Reddit mentions: The best brake cleaners
We found 22 Reddit comments discussing the best brake cleaners. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 9 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. CRC 05089 BRAKLEEN Brake Parts Cleaner - Non-Flammable -19 Wt Oz
- The original brake parts cleaner
- Formulated to quickly & effectively remove grease, brake dust, brake fluids, oils, & other contaminants from brake parts, lining, pads
- Cannot be sold for use in ca or nj
- Non-flammable
- This item is not for sale in catalina island
Features:
Specs:
Color | RED |
Height | 11.25 inches |
Length | 10 inches |
Number of items | 1 |
Release date | March 2010 |
Size | 1 lb 3 Oz |
Weight | 1.4 pounds |
Width | 8.5 inches |
2. VHT SP736 Gold Brake Caliper Paint Can - 11 oz.
Paint has been specifically designed for brake, drum, caliper and rotor custom detailingSuperior heat and chemical resistanceBest when used with primer color paint and clear coat processWithstands temperatures up to 900 degrees when cured properlyThis item is not for sale in Catalina Island
Specs:
Color | Gold |
Height | 7.95 Inches |
Length | 2.61 Inches |
Number of items | 1 |
Size | 11 Ounce (Pack of 1) |
Weight | 0.7275254646 Pounds |
Width | 2.61 Inches |
3. Permatex 82450 Non-Chlorinated Brake and Parts Cleaner, 14.5 oz.
- Penetrates, dissolves and removes dirt and oil from brake systems and metal parts
- Safer for aluminum; helps manage EPA halide limits
- Leaves no contaminant-attracting residue or chlorinated solvent run-off
- Can be applied without disassembling the brake unit since Brake & Parts Cleaner will penetrate to clean
- Suggested Applications: All brake systems, C.V. joints, machinery, tools, and farm equipment
Features:
Specs:
Height | 0 inches |
Length | 0 inches |
Size | Pack of 1 |
Weight | 1.14 Pounds |
Width | 0 inches |
4. 3M 08180 High Power Brake Cleaner - Mid-Level VOC - 14 oz
- Cleans brake parts and assemblies without leaving residue
- Large, ergonomic actuator delivers high powered stream to remove tough deposits
- Cleaner removes brake dust, solvents, greases and oils
- Thorough cleaning action helps eliminate squeal and chatter
- Formula dries quickly and leaves no residue
- For industrial/occupational use only. Not for consumer sale or use.
Features:
Specs:
Color | $$$ |
Height | 12 Inches |
Length | 4 Inches |
Number of items | 1 |
Release date | October 2011 |
Size | 1-pack |
Weight | 1 Pounds |
Width | 4 Inches |
5. CRC Industries (CRC05089) Brakleen Brake Parts Cleaner, 19 oz Can, 12 per Pack
- The original brake parts cleaner, improves the life of car's braking system
- Removes brake fluid, grease, brake dust and oil from brake parts, lining and pads and leaves no residue
- Safe for all brake systems, non flammable
- Cannot be sold for use in CA or NJ or Catalina Island
- Proudly Made in the USA
Features:
Specs:
Color | Colorless Liquid |
Height | 9.25 Inches |
Length | 2.63 Inches |
Weight | 1.3 Pounds |
Width | 2.63 Inches |
6. VHT SP731 Real Red Brake Caliper Paint Can - 11 oz.
- Paint has been specifically designed for brake, drum, caliper and rotor custom detailing
- Superior heat and chemical resistance
- Best when used with primer color paint and clear coat process
- Withstands temperatures up to 900 degrees when cured properly
- This item is not for sale in Catalina Island
Features:
Specs:
Color | Real Red |
Height | 7.874 Inches |
Length | 1.9685 Inches |
Number of items | 1 |
Size | 11 Ounce (Pack of 1) |
Weight | 0.75 Pounds |
Width | 7.874 Inches |
7. OEM TOOLS 24686 Brake Hub Resurfacing Kit
- BRAKE HUB RESURFACER: Maintenance of the brake hub is essential to the overall health of your braking system; Our wheel hub cleaner tool kit easily eliminates the rust on lug studs and rotors on the hub assembly
- ACCESSIBLE TOOL: This wheel stud cleaner tool is compatible with most power drills; Simply select one of the pads and insert the shank into your power drill; Low RPMs and steady pressure will remove rust with ease
- RESURFACE AROUND LUG NUTS: Using a wire brush is inefficient; Our rotor rust remover fits around lug nuts to resurface the space between the nut and the brake hub without disassembling the hub
- RESURFACE ON MANY MODELS: This wheel hub cleaning tool works on cars, light trucks, and SUVs on front and rear brake hubs and rotors; Work on most import and domestic vehicles without hassle thanks to our adaptable brake hub cleaning tool
- SPECIFICATIONS: Includes 4 pads and a mounting surface with an accessible shank; Can be used on passenger cars, light trucks, and SUVs
Features:
Specs:
Color | Multi |
Height | 0.7 Inches |
Length | 11.4 Inches |
Number of items | 1 |
Release date | February 2017 |
Size | Small |
Weight | 0.3 Pounds |
Width | 4 Inches |
8. VHT ESP734000 Gloss Black Brake Caliper Paint Can - 11 oz.
- Paint has been specifically designed for brake, drum, caliper and rotor custom detailing
- Superior heat and chemical resistance
- Best when used with primer color paint and clear coat process
- Withstands temperatures up to 900 degrees when cured properly
- This item is not for sale in Catalina Island
Features:
Specs:
Color | Gloss Black |
Height | 7.874 Inches |
Length | 1.9685 Inches |
Number of items | 1 |
Size | 11 Ounce (Pack of 1) |
Weight | 0.94 Pounds |
Width | 7.874 Inches |
9. Nigrin 74057 Brakes and Parts Cleaner 500 Ml
Removes dust, oil, grease, tar, hydraulic fluid and other tough stainsAbsorbs asbestos dust and even loosens resin residuesAcetone-free and quick-drying
Specs:
Height | 10.236220462 Inches |
Length | 3.93700787 Inches |
Weight | 0.0220462262 Pounds |
Width | 3.93700787 Inches |
🎓 Reddit experts on brake cleaners
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where brake cleaners are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
Thank you!! Absolutely, here's the video that we watched and followed very closely: https://youtu.be/H9xn066qfKo
Some notes:
CRC 05089 BRAKLEEN Brake Parts Cleaner - Non-Flammable -19 Wt Oz https://www.amazon.com/dp/B000LDR9HI/ref=cm_sw_r_cp_apa_i_fbdvDbZNSKSJG
120 Grit Dry Wet Sandpaper Sheets by LotFancy, 9 x 3.6", Silicon Carbide, Pack of 45 https://www.amazon.com/dp/B075WV8PN9/ref=cm_sw_r_cp_apa_i_NfdvDbPYQJ1VG
A. Good for the holes in the caliper and very tight spots (I painted almost all the way to the back of the caliper to make sure it looked red at every possible angle).
Check out this item at Target https://www.target.com/p/e-l-f-blending-eye-brush/-/A-14653397
B. A stiffer brush for the verrrrry tight spots where the caliper meets the brake pad and you do NOT want to have Shakey hands and get anything near those pads.
Check out this item at Target https://www.target.com/p/e-l-f-concealer-brush/-/A-13958833
C. For extra measure when you are doing touch up in those tight spots (this one is $3):
Check out this item at Target https://www.target.com/p/e-l-f-angled-eyeliner-brush/-/A-13586153
https://www.ebay.com/itm/TESLA-HI-TEMP-PREMIUM-BRAKE-CALIPER-DECALS-STICKERS-CAST-VINYL-/362070373338
https://teslamotorsclub.com/tmc/threads/want-painted-calipers-dont-want-to-spend-600-on-them.140873/#post-3346753
My husband didn't want to do this method because prep looked much more intense and he'd figure I wouldn't mind a painting project on a cloudy Saturday afternoon.
If you are in my state, I'd be happy to help. I'm new to reddit so not sure how to do the direct messages but let me know! Hope this helps! Please don't hesitate to ask questions when you start this. 150% worth the effort. It's beautiful and the Tesla service man honestly thought our SR+ was a P3. Even after pulling up the computer to look at the specs, he kept saying,"You're so lucky to have a performance!". I didn't have the heart to tell him it wasn't. Best of luck!!!
For anyone who is interested, I used VHT Gold Caliper Paint.
I kept the brake lines connected but removed the calipers and pads. Then washed/scrubbed them with soap water, followed by a wipe down with denatured alcohol to remove any oils.
Then I masked everything off, as you can see in the first pic. After three coats I was happy with how they looked. Next came a heat gun to cure the paint. About 20 minutes on each caliper.
Reassembled and was done! I'm more than happy with the stock brakes on the SV but wanted a bit more color. I'm really pleased with how they turned out!
edit: Not A Lawyer
 
 
This is absolutely the answer.
I suggest a Fernco seal rather than a wax ring. It is more secure and a tighter/better seal than oldschool wax rings.
A wax ring only gives you one shot to get a good seal. Once mushed it won't seal well. If the toilet moves, it may leak.
The Fernco has a powerful adhesive that sticks to the bottom of the toilet and the funnel extends a little bit into the pipe.
There are two sizes, 3" and 4".
To do an extra good job, use brake cleaner or Goof Off (not goo-gone or citrus) to strip all the wax residue from the toilet.
Make sure the toilet is well bolted down, doesn't rock.
 
Links: (no affiliate/interest)
https://www.amazon.com/Fernco-Inc-FTS-4-4-Inch-Toilet/dp/B000BVMZUG/
https://www.amazon.com/CRC-05089-BRAKLEEN-Brake-Cleaner/dp/B000LDR9HI/
https://www.amazon.com/Goof-Off-FG653-Professional-Strength/dp/B002MPPYYS/
https://www.amazon.com/LASCO-04-3645-6-Inch-4-Inch-Washers/dp/B000FH6GI8/
I'm probably gonna die, but I use a quick blast of automotive brake parts cleaner to get my cams clean, dry them with compressed air, and apply Liquid Wrench Teflon spray lube. Seems to get the cams good and clean without scrubbing, and keeps things nice and smooth operating for a long time without attracting gunk.
I recommend the paint route, it doesn't look cheesy, leaves all clearances as OE intended (no interference from covers causing certain wheels to have fitment issues), and is easy to maintain.
My general steps when doing it are:
kit
single can
single can again- This is what I always use
Also some people like to paint the rotor hats to match, I personally think they look weird except in black, but its your car so do what you want to do.
Be sure to post some pics for us as well!
Question.
Why does the grease need removed? Greasing electrical contacts isn't necessarily uncommon to help prevent corrosion (and copper loves to corrode in ways that electricity doesn't like).
If you're sure you want to remove the grease, use America's favorite libation: CRC Brākleen in the non-California-approved red can. It's usually cheaper locally: I bought some today at Harbor Freight for $7.
You can also buy it by the gallon or larger, up to (at least) 55 gallon drums.
I'll just give you a list of the items I've been using (and like):
https://www.amazon.com/Hakko-T18-D08-D12-D24-D32/dp/B00C1N30DI Hakko FX-888D. The extra tips may be unnecessary, I only ever use the one chisel tip
https://www.amazon.com/gp/product/B00068IJPO Leaded solder
https://www.amazon.com/gp/product/B004SPGFT8 Brushes
https://www.amazon.com/gp/product/B00FZPDG1K Side cutters
https://www.amazon.com/gp/product/B00425FUW2 Flux
https://www.amazon.com/gp/product/B008O9VLA2 Solder Wick
https://www.amazon.com/gp/product/B0013HT2QW KimWipes
https://www.amazon.com/gp/product/B001B5JT8C Isopropyl Alcohol
https://www.amazon.com/gp/product/B005CU56KM Acetone spray (use carefully/sparingly)
https://www.amazon.com/gp/product/B004G5T9M0 Jewelers loupe
https://www.amazon.com/gp/product/B019SLLOMY Tweezers
https://www.amazon.com/gp/product/B00P8Z4RPG Hot air station (works well despite Chinesium)
Also, I noticed in Dave's videos he rarely adds flux, just the flux that's built into the multicore solder. I don't know if I'm alone on this one but with flux I always felt the bigger the glob the better the job. Just have to clean it afterwards with the solvent, tissues & brushes.
Edit: Okay that's a much bigger list than I thought, this stuff can get expensive!
Have you ever tried something like that with success? Is this: https://www.amazon.com/3M-08180-Power-Brake-Cleaner/dp/B002WQHY9K the product you might use to clean off the WD40?
You don't know what brakekleen is?
Edit: it's the best stuff in the world
https://www.amazon.com/dp/B000LDR9HI/ref=psdc_15718981_t1_B0002FU44K
You have to get the chlorinated stuff though, if it says non chlorinated don't waste your money.
My $100ish must have use everyday options include: cordless 3/8 ratchet https://www.amazon.com/dp/B07CZWBYBK/ref=cm_sw_r_cp_api_i_Tw.2DbXFTMF30, lighting! a good rechargeable headlamp https://www.amazon.com/dp/B07CV3VTYB/ref=cm_sw_r_cp_api_i_aI.2DbYZ76FY7, flashlight or decent under hood light https://www.amazon.com/dp/B01MTXC016/ref=cm_sw_r_cp_api_i_sK.2Db40MCX8D, a portable jump box https://www.amazon.com/dp/B015TKUPIC/ref=cm_sw_r_cp_api_i_mL.2DbX8E94SN or 24 cans of brake cleaner https://www.amazon.com/dp/B00JRPDW7M/ref=cm_sw_r_cp_api_i_Du.2DbZ2WMZDE
CRC Brakleen Brake Parts Cleaner - Non-Flammable https://www.amazon.com/dp/B000LDR9HI/ref=cm_sw_r_cp_apa_GlHrzbCJQDQZZ
Order it yourself, unless you live in CA or NJ, in which case this might be more useful.
Try brake parts cleaner. The kind that contains tetrachloroethylene, which is a dry cleaning fluid. It won't disturb the paper. Idk about the ink, but it is worth a try.
Nintendo joystick shafts go through a captured ball in the base which probably needs a thorough cleaning.
I would start by completely disassembling it and cleaning the entire base, especially the area around the ball. I use Brakleen to de-gunk them. Then after it dries, I use a silicone lubricant on all the metal mating surfaces.
I use a bit of scotchbrite pad or a small abrasive wheel (just remove the rust).
One VERY handy thing is a hub-cleaner attachment that has a hole so you can scrub off the rust around the wheel studs. ALWAYS clean the rust off the hub face and the back of the wheel.
Also in terms of doing brakes the right way, get a runout gauge and caliper and learn how to index rotors. Failing to index rotors will result in pedal vibration over time,
http://www.hendonpub.com/resources/article_archive/results/details?id=1787
https://www.amazon.com/OEMTOOLS-24686-Brake-Hub-Resurfacing/dp/B06W55QQHG/
check this out
strip them with Brakleen and then re-oil them with some tool oil.
CRC Brakleen is the best instant killer of Black Widow spiders money can buy
I had to change both pads (front and back) after not even 300 km (~185 miles) riding (~10.000 meters (~33.000 ft) altitude change). Pads used: Link
I am not that light weighted (but sub 100 kg (~200 lbs)) but changing the pads every month sucks. Discs are clean (and I clean them every now and then with breakcleaner and I have no rubbing/sound problem.
I mean brake-parts cleaner. it melts that shit right off. I just had to do it with my car.
I found this but I don't know how well it will stick to or be nearly as durable as the original porcelain coating. Is it really bad?