Reddit mentions: The best furniture legs
We found 292 Reddit comments discussing the best furniture legs. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 106 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. BQLZR Stainless Steel Kitchen Adjustable Feet Round 2" Dia Furniture Leg Pack of 4
- [Load-bearing] Each load-bearing capacity is 25KG, 4 of them have a total load-bearing capacity of 100KG, and the number can be added as needed.
Although the stainless steel part is hollow, the stainless steel itself is very hard. Our product qualification certificate proves this. The service life of the product can reach fifteen years or more. - [Screws] The suitable screws for the furniture legs are M3.5x16mm, They are not included in the product
- [Basic function] The amount of adjustment provided by the threaded rubber stop is sufficient to compensate for uneven ground
It is an ideal choice for coffee tables, sofas, TV cabinets, beds, bathroom cabinets, office furniture, kitchens, cabinets, shelves, etc.
It can also be used as a support for the desktop partition to create a drawer space
They can adjust the height of the cabinet feet from 10CM to 11.5CM, which can blow out the debris under the cabinet - [Features] The plastic part design will not wear your painted partitions or wooden floors
The lightweight design of stainless steel, even if the body bumps against the stainless steel furniture feet, there will be no pain or injury
Smooth design of stainless steel material, you can paste your favorite drawings on the stainless steel part - [Note] 1,The furniture needs to be lifted instead of pushed and pulled when moving, which is beneficial to prolong the service life of the furniture feet2. Need to tighten the plastic thread part.3.Adjust the furniture to a suitable height for more comfortable use
Features:
Specs:
Color | Black,silver |
Height | 3.93700787 Inches |
Length | 1.968503935 Inches |
Width | 0.0393700787 Inches |
Size | 104mm |
Number of items | 4 |
2. VOVOV Furniture Cabinet Metal Legs Adjustable Stainless Steel Kitchen Feet Round Black and Silver 50 x 50mm Pack of 4 + 16x Screw
Unique design of adjustable height.Accessories for DIY furniture, cabinets, shelves ect.Size: 50x50mm (DiaxH);Black Steel Pads Width:60X60Mm (2.35X2.35Inch);Height:50mm/1.96InchMade of Stainless Steel durable.Easy Install, Adjustable Height. Including 16 screw
Specs:
Color | Black/Silver |
Height | 1.968503935 Inches |
Length | 1.968503935 Inches |
Width | 1.968503935 Inches |
3. Black Adjustable Table Leg Set - Set of 4
- Legs simply screw into mounting plates
- Four 28'' Long x 2'' Diameter metal legs
Features:
Specs:
Color | Black |
Height | 2.01 inches |
Length | 34.02 inches |
Width | 9.02 inches |
Size | 50mm x 710mm |
4. SMARTSTANDARD 28" Heavy Duty Hairpin Coffee Table (Black) 1/2" Thick Set of Four (Legs x 4), 28 Inch 4PCS
ADDITIONAL FLOOR PROTECTORS – When you purchase a set of mid-century modern legs you’ll also get a set of rubber feet! Use them to protect your floors from damage or as an added stabilizer for that wobbly chair or table.DIY PROJECT - Mount these 28inch legs (set of 4) with the tabletop of your c...
Specs:
Color | Black |
Height | 6.3 Inches |
Length | 29.53 Inches |
Weight | 19.58 Pounds |
Width | 6.3 Inches |
Size | 28 Inch |
Number of items | 4 |
5. BQLZR Furniture Cabinet Metal Legs Adjustable Stainless Steel Kitchen Feet Round Black and Silver 50 x 50mm Pack of 4
- [Load-bearing] Each load-bearing capacity is 37.5KG, 4 of them have a total load-bearing capacity of 150KG, and the number can be added as needed.
Although the stainless steel part is hollow, the stainless steel itself is very hard. Our product qualification certificate proves this. The service life of the product can reach fifteen years or more. - [Screws] The suitable screws for the furniture feet are M3.5x16mm, they are the parts you need to buy extra
- [Basic function] The amount of adjustment provided by the threaded rubber stop is sufficient to compensate for uneven floors
It is an ideal choice for coffee tables, sofas, TV cabinets, beds, bathroom cabinets, office furniture, kitchens, cabinets, shelves, etc.
It can also be used as a support for desktop partitions to create space as a drawer
They can be adjusted between 50 mm (2 inches) and 70 mm (2.75 inches), which can blow out the debris under the cabinet - [Features] The plastic part design will not wear your painted partitions or wooden floors
The lightweight design of stainless steel, even if the body bumps against the stainless steel furniture feet, there will be no pain or injury
Smooth design of stainless steel material, you can paste your favorite drawings on the stainless steel part - [Note] 1,The furniture needs to be lifted instead of pushed and pulled when moving, which is beneficial to prolong the service life of the furniture feet2. Need to tighten the plastic thread part
Features:
Specs:
Height | 1.968503935 Inches |
Length | 1.968503935 Inches |
Width | 1.968503935 Inches |
Size | 50mm |
6. IKEA - CAPITA Leg, Stainless Steel 4 3/8-4 3/4" (X4)
Package quantity: 4 packDiameter: 1 1/8 " Min. height: 4 3/8 " Max. height: 4 3/4 "Mounting plate: Steel, GalvanizedLeg: Stainless steel
Specs:
Weight | 1 Pounds |
7. Heavy Duty Leg Leveler, Wide Foot (1)
Leg leveler, 2-3/8" diameter footFeatures a lipped mounting bracketPerfect for cabinets, tables, or shelving unitsUse a #5 hex wrench for adjustmentMade of heavy gauge, plated steel1-3/4" adjustment
Specs:
Color | Stainless Steel |
Height | 2.5 Inches |
Length | 4 Inches |
Width | 2.5 Inches |
8. Rok Hardware 4 Pack Heavy Duty 8000 LB Capacity Adjustable Furniture Leg Leveler
Holds Up to 8000 Lbs Made of heavy duty steel with a 2000 Lb capacity Per leg levelerIncludes allen key for height adjustment. And #10 x 3/4" high strength installation screws.Leg Base Diameter: 1-1/4" | Leveler Total Height: 2-1/2"Leveler Pin Length: 3 InchesRok Brand is sold exclusively by Rok Har...
Specs:
Height | 9.9999999898 Inches |
Length | 2.99999999694 Inches |
Weight | 1.15 Pounds |
Width | 2.99999999694 Inches |
9. Leg Leveler with T-nut (4-Pack)
- Screw on T-Nut
- 3" Tall Leveler with 1-7/16 Pivoting Nylon Glide
- 3/8-16 Thread
- Easily adjust with screwdriver on top or wrench at base
- Includes 4 - leg levelers and 4 - t-nuts and screws
Features:
Specs:
Color | Nickel |
10. IKEA - CAPITA Leg, Stainless Steel 6 1/4-6 3/4" (X4)
Package quantity: 4 packDiameter: 1 1/8 " Min. height: 6 1/4 " Max. height: 6 3/4 "Mounting plate: Steel, GalvanizedLeg: Stainless steel
Specs:
Height | 1.90157480121 Inches |
Length | 6.20078739525 Inches |
Weight | 2.05 Pounds |
Width | 5.70078739576 Inches |
11. Waddell 2506 Taper Round Leg, 6-Inch
- Waddell 2506 6-Inch Taper Round Leg
- Hardwood taper leg Round
- This Product is manufactured in China
Features:
Specs:
Color | Yellow |
Height | 1.5 Inches |
Length | 5.5 Inches |
Weight | 0.1 Pounds |
Width | 1.5 Inches |
Size | 6 Inch |
Number of items | 1 |
12. Industrial By Design - 16” Hairpin Table Legs - (Raw Steel) Elegant Mid Century Modern - Two Rod Design - Premium Heavy Duty Build - Easy DIY Installation - Set of 4
- Book: a new course in reading pali: entering the word of the buddha
- Binding: paperback
- Language: english
Features:
13. Signstek 28" Hairpin Table Legs with Heavy Duty Metal and Industrial Design for Coffee Tables, Modern Desks and Night Stands,Set of 4
- High-quality and Sturdy: Made of 3/8" Solid cold rolled iron and coated powder on black finish, it is so solid that it can carry up to 350 lbs. Provide great stability for furniture hardware projects.
- Classic Design: a classic mid-century modern hairpin legs help you to create industrial modern furniture designs and make it unique, durable and beautiful.
- Easy Installation: The mounting bracket is pre-drilled with 5 holes for easy and quick assembly. Comes with screws.
- Multiple Applications: Great for DIY coffee tables, modern desks, night stands, stools, media centers, and benches and school desk for home. Packaged with a U type sponge bar and coated powder on black finish, no worry to cause scratches. (Not include hardware)
- Extra Bonus: come with 4 hairpin leg feet protector to protect your floors from damage
Features:
Specs:
Color | Black |
Size | 28 inch Three-Rod |
14. Set of 2 Ikea Capita Stainless Steel Legs
- Main Specifications Product Description Logitech Marble Mouse - trackball Device Type Trackball
- Connectivity Technology Wired - PS/2, USB Movement Detection Technology Optical Buttons Qty 4
- Features Scrolling 2-way button Cables Included 1 x mouse adapter - external
- OS Required Microsoft Windows 95/98, Apple MacOS 8.6 or later, Microsoft Windows 2000 / NT4.0, Micro
- Manufacturer Warranty 3 years warranty - NOTE: THIS PRODUCT CANNOT BE SHIPPED TO MASSACHUSETTS OR DISTRICT OF COLUMBIA (WASHINGTON, D.C.)
Features:
Specs:
Height | 3.3 Inches |
Length | 8.7 Inches |
Weight | 3 Pounds |
Width | 4.8 Inches |
15. AECOJOY 16" Black Hairpin Legs, 3/8" Diameter, Set for 4 Heavy Duty 2 Rods Table Legs, for DIY Desk, Stand, Bench
- AECOJOY 16" Hairpin Table Legs, the set of 4, 20pcs 4/5" screws,4 rubber feet, 3/8" Solid Raw Steel and Stain Black finish
- IDEAL FOR ANY DIY PROJECT: apply to coffee tables, night stands, end tables, media console, self-designed desk and bench.
- EASY INSTALLATION: Pre-drilled holes in mounting plate for quick assembly
- INDUSTRIAL QUALITY: Manufactured with industrial strength quality, support 350 pounds
- -SATISFACTION GUARANTEED: 100% money back guarantee if unsatisfied with item
Features:
Specs:
Color | Black |
Height | 19.9999999796 Inches |
Length | 3.99999999592 Inches |
Width | 3.99999999592 Inches |
Size | 16 Inch |
16. Rustic 30 Inch Industrial Pipe Decor Table Legs - Set of 4, Authentic Rough Black Iron Fittings, Flanges and Pipes for Custom Vintage Tables and Furniture Decorations, DIY Kit with Hardware, 30” X 1”
- Set of 4, 1 inch pipe table legs; kit comes with all pipes, fittings, and hardware needed to assemble your own 30 inch DIY industrial table legs for kitchen or dining tables; step by step instructions and screws to attach legs to tabletop included; tabletop not included
- Easy to clean and seal; components are coated in a light industrial grease in order to prevent rusting; easy and quick clean and seal instructions included; see video tutorial for more information
- Made with durable materials; all fittings are industrial grade malleable iron; pipes are standard grey steel, known as black within the plumbing industry
- Industrial quality; all pipes and fittings made to meet American Society of Mechanical Engineers and American Society for Testing and Materials standards
- Suits every aesthetic; steampunk lighting, industrial, factory, urban chic, French country farmhouse, vintage, retro, reclamation, minimalist, DIY customized, and more; can be painted to match any color scheme or clear coated neutral black or grey
Features:
Specs:
Size | 30 Inch |
17. WoodRiver Heavy-Duty Leg Levelers, Small Foot (4)
- Set of four 1-5/16" diameter leg levelers, small foot
- Features a lipped mounting bracket
- Set of four levelers has a load capacity of 600 lbs
- Fixed base with plastic protective cap - Made of heavy gauge, plated steel
- WoodRiver is proudly made by Woodcraft, America’s leading supplier of saws, planes, power tools, hand tools, wood stain and paint, routers, sanding, wood, kits, dust collection and more. Our award winning family of brands includes WoodRiver, Highpoint, Woodcraft and Woodcraft Magazine as well as the greatest selection of woodworking books, videos, and plans.
Features:
Specs:
Color | Stainless-steel |
Height | 2.65 Inches |
Length | 6.75 Inches |
Width | 3.95 Inches |
18. 28" Tall, Single Table Leg, Office Height - Brushed Steel - from TableLegsOnline
- Diameter: 2-3/8" (60mm)
- Finish: Brushed Steel
- Height: 28" (711mm)
- Sold as single leg, includes mounting plate with 1" adjustable leveler foot and mounting screws
- 220 lbs. (100kg) vertical load rating per leg
Features:
Specs:
Color | Brushed_steel |
Height | 28 Inches |
Length | 2.38 Inches |
Weight | 4 Pounds |
Width | 2.38 Inches |
Size | 28" |
19. 2 Rod Hairpin Legs - Made in The USA - Commerical Grade - Each Leg Sold Separately (40” Height x 3/8" Diameter - Each Leg Sold Separately)
INDUSTRIAL TABLE LEGS: Apply these timeless hairpin table legs to the tabletop of your choice to create a one of a kind mid-century modern piece. A great DIY project, these 2 rod, 2 pin designed table legs can create a custom coffee table, end table, laptop desk or night stand.EACH LEG SOLD SEPARATE...
20. Homend Plastic Sofa Legs, 4 Pack Sofa Legs Replacement Furniture Sofa Legs with Mounting Plates Screws Chair/Couch/Loveseat/Cabinet M8 Thread (Metric 8mm) Compatible for IKEA Or US Made Furniture/Beds
✅【Durable Material】: Plastic sofa legs are made with high density polypropylene which can bearing a certain weight and not easy to bending or breaking, can be used for a long time✅【Size】: Height: 6.8’’ (17cm), Top Width:2.3’’(6cm), Bottom Width:1.5’’ (4cm). 5/16’’ Diamete...
Specs:
Color | Black |
Size | Leg Height: 5.6"(142mm) |
🎓 Reddit experts on furniture legs
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where furniture legs are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
I’ve always really been into music. I imagine that’s a given for most people on here. It started when I fixed up the amp and speakers I found in my moms basement when I was home from college one winter. They are both Pioneer, late 80s I’m guessing. Originally I wanted to use the amp and speakers to play music from laptops, phones, etc. at our college house parties which we did and it was awesome. I also took back all of my parents records to school with me and really didn’t listen to them, didn’t think a college party house was the safest place for a set up and didn’t own a player. Fast forward 7 years I’m finishing grad school and moving in with my girlfriend...we do a favor for her sister and brother in law and end up with an Audio Technica player for the free. Found Discogs pretty soon after that, and I’ve been collecting since. Today I added the tuner, also late 80s Pioneer. Big fan of the green light on the face of it. The shelf where the records are is a super cheap cubicle from Target that we didn’t put in the middle shelves. Ordered the legs from Amazon, probably a total of 75$ between the two. Anyways thanks for reading.
EDIT: Wow, didn't really expect this to blow up like it did. You all are really nice, thank you! I'm gonna try to answer some of the comments here:
Throwing out a few ideas.
Starting with the pine countertop. Apply a contact paper such as this marble one to add a more refined look. Choose a contact paper that is made for countertops and matches your home. Consider something similar to your bathroom or kitchen counters. There are many styles of contact paper such a tile and stained wood. I would also add table legs like these to stabilize the countertop, especially for my next suggestion. Make sure the countertop sits at least a couple of inches above your washer and dryer (I know it seems like a no brainer but just in case).
To help distract away from everything thats going on, I would add a cube shelving unit like this one. Use fabric cube boxesto store your detergent and other cleaning supplies. They come in different colors and designs. Make sure you order the right size for your shelving unit. This idea would help visually clean up the space. If you decided to do this, I would remove the wall shelf. I would not suggest doing this without attaching table legs to the pine.
Throw up a tension rod with a neutral curtain to divide off the room. I would use rings since fabric on rod isn’t good for constant movement. If your home calls for it or you’re into some extra, look into decorative hooks.
Hopefully my suggestions will help you create a great laundry room that fits your needs and requests.
After a massive backache from a play session on my new cocktail cabinet, I decided I needed to add some height. Sitting in an 18" kitchen chair, the control deck was situated between my knees.
Here's how I added an easy 6" of height. The bolts on the sofa feet are slightly larger than the bolts on the feet that came with the cabinet, but it you remove the old mounting plates, the existing holes for the feet line up with the new mounting plates perfectly! Easy win!
It's much more comfortable for me to play sitting on an 18" chair now, though my 5'2" wife says she wants a phone book to sit on. 😆 I'll get her a 24" bar stool.
Hi, thanks in advance for any help or advice.
I wish to build a work-space for painting that is 2.4 meters long (7.87 feet), 120 centimeters tall (3.9 feet), and 60 centimeters deep (1.9 foot). There will be a lip of maybe 2 centimeters (an inch) on the front and sides, and a 30 centimeter (a foot) splash-back. The most important requirement is that it needs to be perfectly level at all times across the entirety of the surface, and it needs to be easily adjustable to make it perfectly level.
Im planning on using laminated MDF for the surface, and 8 leg levelers
Is this the best route for creating a perfectly level work-space? Cheers guys and gals.
Thanks! It was a fun build and I've loved using it so far.
https://www.amazon.com/gp/product/B0035Y5XUK
I haven't used anything like it prior, but they seem to be strong and well built. So far no wiggle, even on the legs where they are extended fairly far. The hex head top was easy to adjust with a long enough drill bit, but a flex bit might make it easier. With all the weight on them, it did take a second to adjust when I tried to do it by hand. One thing to note is that the screw positioning is wider than the edge of the 2x4, so I had to position all of them on the flat. For my use it wasn't an issue, but it could be a problem in some cases.
Thanks! I'm very happy with how they are working out great how ever I would recommend not getting the 4" ones if you a shorter person. I'm 6'4" and it is border line to tall for me lol unless you don't mind you legs hanging.
BQLZR Stainless Steel Kitchen Adjustable Feet Round 2" Dia Furniture Leg Pack of 4 https://www.amazon.com/dp/B00KQH8HMU/ref=cm_sw_r_cp_apa_QtXozbXJ4V6DC
Thinking about assembling a desk as my first DIY project, inspired by a lot of the posts over at /r/battlestations/. I'd be very grateful if someone with experience can double check my plan for obvious faults or suggest a better way of doing things.
I was considering buying a butcher's block countertop, since I really like the way they look. I was looking at this one from Home Depot as the length is pretty much exactly what I want.
I know this needs finished, a friend of mine recommended Danish Oil and this guide. Is Danish Oil sufficient? Whatever I use as finish I don't want it to be overly shiny. I'll use coasters for drinks and might occasionally eat food at the desk.
After I sand/finish the wood, all I would need to do is attach some legs, I was looking at these 28 inch hairpin legs from Amazon. I'm not super attached to these and would welcome alternatives. I just know that I don't want drawers.
Things that I may want to add but haven't decided on: mounting my monitors to the desk itself with an arm, and something to attach to the underside of the desk to assist with cable management.
Is there anything obvious that I'm missing here? I own a drill, other than the wood and legs I'd need to buy some sand paper and danish oil for the finishing. Would this length of wood need support in the middle? I have two 27" monitors that will sit in the middle of the desk, and keyboard/mouse at a minimum. My PC and PS4 might also go on top to the sides.
Thanks in advance for any guidance.
The desk is IKEA and one part from Amazon:
Karlby Countertop:
https://www.ikea.com/ca/en/p/karlby-countertop-oak-90335211/
Alex Drawers x2:
https://www.ikea.com/ca/en/p/alex-drawer-unit-white-10192824/
Desk Risers:
BQLZR Stainless Steel Kitchen Adjustable Feet Round 2" Dia Furniture Leg Pack of 4 https://www.amazon.com/dp/B00KQH8HMU/ref=cm_sw_r_cp_api_i_1su7CbPE8JM5P
If you look up the “Karlby IKEA Desk” online or YouTube or any media outlet I’m sure you’ll find a plethora of information. It’s a very popular desk setup.
Not to mention it fit perfectly in my bedroom nook.
You all are correct, I went to ikea store and got the countertop karlby wood. Very durable and meant for rough encounters. Mixed with Grey or black Alex drawers and I love it. Very popular on reddit, I don't bolt them down but you can with these if you want. Also upgraded from a glass desk and I love this setup!
VOVOV Furniture Cabinet Metal... https://www.amazon.com/dp/B01NCKZRTL?ref=ppx_pop_mob_ap_share
This is from an earlier reply I've made.
picture of the door (also yes, the color is ugly, but I'll repaint it at some point).
You can do what I do.
Door Table! All you do is buy a door, buy some adjustable legs, a screw-in keyboard tray if you feel like it, and screw those motherfuckers together!
Advantages
Parts
Door
Door - $66. Note that this one does not have a finish coat, the one I bought did (it's pretty easy to paint, or find one that has a basic weather coat). Can't see anything in america (my one was made in australia).
edit: same door with white primer
Obviously, you'd have to pay for the entire door even if you do cut it down. That being said, it already has a finish coat, and for the quality of the wood (and the fact it is already in a table shape) it is worth the $66.
legs
Ikea GERTON adjustable leg * 4 - $25 each, for $100. Amazon also has a heap of legs, but your mileage may vary (example)
if you are going to cut it down to half the size (or less) you can use these half-diameter legs and save some space/money:
http://www.ikea.com/us/en/catalog/products/30264301/
accessories
And that's about it! You can add a fifth leg if you want the extra support, but you don't need it. All that is left is a keyboard tray, like this.
Once you're all said in done, for a couple hours of work, you will have an extremely sturdy and customizable desk. It's also hell of a lot cheaper to do then to buy a premade desk.
It looks like the counter is supported by a piece of angle iron bolted to the wall. And that whatever they put the bolts into isn't providing sufficient structure to carry the weight of the counter top.
Get a piece of stain grade wood that's almost the right length, and attach something like this to the bottom to get it level and carry it: http://www.amazon.com/Heavy-Duty-Leveler-Wide-Foot/dp/B0037MK8XC/ref=sr_1_8?ie=UTF8&qid=1416936895&sr=8-8&keywords=leveling+leg
You'll then of course need a way to secure that leg to keep it stable.
I have almost this same desk (check my post history). The capita legs at Ikea are 4inches tall which almost made my desk TOO high. Love it over all though. There are better ones which I wish I would have went with BLQZR legs on Amazon which I believe are 2-2.5inches which would have been better, although I don't know the build quality on those. The Ikea Capita legs are sturdy as hell.
EDIT: these are the legs I was talking about on amazon, they were the ones the YouTuber RandomFrankP used as well https://www.amazon.com/BQLZR-Stainless-Kitchen-Adjustable-Furniture/dp/B00KQH8HMU
Thanks. I ended up having to cut and paint my own pieces to make the second level. Like I’ve seen others do on this sub, I bought the Ikea 6” risers to raise it up https://www.amazon.com/gp/aw/d/9178881986/ref=yo_ii_img?ie=UTF8&psc=1
Having the second level is pretty awesome
For any of your metal tools, coat them in a layer of oil to protect them from the moisture. Just spray some wd-40 into a shop rag and wipe them down with it if you don't have anything fancier. Old tools with some rust can mostly be recovered with persistence, but you want to keep them from getting worse. New tools you'll want to oil as well, and keep in a toolbox or similar.
I just bought these levelers with the plan of using them with my workbench to both get a level surface and to keep the posts off the ground. Getting the wood off the floor will definitely help slow any rot. You could also try weatherproofing/sealing the lower part of the legs on your bench, but it may be too late for the existing legs.
If you're going to be storing boards and other wood stock in the garage, I'd definitely suggest at least a canopy cover for your stack, given how leaky the garage sounds.
Is the door with the gaps the overhead garage door, or a regular swing door to the outside? If it's a swing door, you could replace both the door and frame somewhat easily and all your gaps would go away. Harder than replacing a broken piece of glass in a window, but easier than replacing an entire window frame.
not op but i think you have to buy them separately. like the table top is one item, the two drawers are both individual items, then the 8 (or however many) legs are individual items (they do come in bundles however) then after you purchase you can assemble them in any formation you want
edit: looked up those stands if you’d like to check them out on amazon i think it’s the same ones
They are actually pretty sturdy. I have 8 legs, 4 per side desk with the top mounting to both, and they all came with rubber feet. The feet make a big difference as far as sliding, but the legs themselves are solid.
I went with the 3 rod design over the 2 rod because I feel like it'd also help. Here is a link to what I bought.
my sub built one from the toilet sit. He drilled these legs into them. Trust me I am very happy that he did that. It was as if I was rimmed for the first time.
Quite sturdy for me to sit on and good enouth space for him to go under with a pillow.
You could try a version with a side mount bracket...but not as clean looking.
Good luck and thank you :)
What I ultimately wound up doing was going the Ikea route. I bought 2 of the Alex drawer units, and a 98" kitchen counter top as well as 4 legs. You can get a smaller counter top to match your available space. I am very happy with the set up and the whole thing was around $300 which is far less than you would spend on a purpose made desk. Links to the parts are below.
Alex Drawer Unit
Ekbacken Counter Top
Olov Legs
Small legs for spacing off the top of the drawer units.
Thank you! This definitely feels like the way to go. I'm considering these to strengthen the back, and I'll pull the Alex drawers forward so they're flush with the front.
https://www.amazon.com/gp/product/B001DSZVTI/
Is there anything that attaches both to the top and bottom?
This looks somewhat close.
Edit: pretty sure this wouldn't work since the bottom part needs to rotate freely and not be attached to anything.
If it isn't too heavy, I would use some hair pin legs like here. Alternatively, consider some cross legs with a middle brace, it might looks really nice with that thick of a table top.
Also a Shou sugi ban wood burn finish with a coat of poly on top looks very good in my opinion. It really depends on what other pieces you have in the room/house. I just like the burnt finish because it keeps the grain of the wood and makes the table a center piece of the room. Just IMO
https://www.amazon.com/BQLZR-Stainless-Kitchen-Adjustable-Furniture/dp/B00WWPVXK2/ref=as_li_ss_tl?ie=UTF8&dpID=41QXD-3cxDL&dpSrc=sims&preST=_AC_UL320_SR320%2C320_&psc=1&refRID=8HB11SPCRMTK69RXA5RR&linkCode=sl1&tag=randomfrankp-20&linkId=7033e16448fe196dc583bea3139b5309&th=1
I've seen some people use these and they're about half the height of my risers. I honestly might switch to them when I move in a few months. Seems like they'd be perfect.
Thanks and sorry for the late reply. The wallpaper is from Ori and the Will of the Wisps, an upcoming game (first game called Ori and the blind forest is also worth looking at, has some great visuals too). The two stands at the side are custom made simply by using some small furniture legs similar to these which made it easy to adjust the height of the monitors.
Thanks!
When I bought them, they were a $4 add-on item. Home depot sells similarly priced legs. Both retailers sell them in a variety of shapes and sizes. I used the same stain on the legs, and it matches better than the pic indicates.
Here are the support things.
Thanks for the love y'all! Here's the link to the legs!
Hey! Thank you I appreciate that! I made them using these [legs] (https://www.amazon.com/gp/product/B00KQH8HMU) and used just the top part of this [monitor riser] (https://www.amazon.com/gp/product/B01A6LS9P0). Anything for the top works, one of the stands is a computer door from an ikea desk (can you tell which one, haha). I just found a monitor riser that was close in size.
Wish I would say they were thrifted, but it was just our future overlord Amazon. Only 40$ which is pretty decent.
That sounds pretty cool!! Here is a link for hair pin legs.
Signstek 28" Hairpin Table Legs with Heavy Duty Metal and Industrial Design for Coffee Tables, Modern Desks and Night Stands,Set of 4 https://www.amazon.com/dp/B01LVTW8JB/ref=cm_sw_r_cp_api_i_0R1XDbH8E4W23
I only do wood working for personal use for our home. I’m still learning but I’ve come a long way. I need a better table to work at to do more detailed projects.
Some of the stuff was on sale when I got it so price is a little off.
https://www.homedepot.com/p/Hardwood-Reflections-6-ft-2-in-L-x-2-ft-1-in-D-x-1-5-in-T-Butcher-Block-Countertop-in-Unfinished-Birch-BBCT152574C/301812823
For the legs I also got them trimmed to 28inches and had them rethreaded on the trimmed side, they can do that for you had Home Depot/Lowe’s . Make sure there all perfect and not different lengths from each other, had that happen.
https://www.amazon.com/Rustic-Inch-Industrial-Decor-Table/dp/B07FLKHBB8/ref=mp_s_a_1_4?keywords=industrial+pipe+legs&qid=1569683709&sr=8-4
Get a bigger can of you want a big table(at least 4 coats)
https://www.lowes.com/pd/Minwax-Polycrylic-8-fl-oz-Gloss-Water-based-Polyurethane/999914411?cm_mmc=shp-_-c-_-prd-_-pnt-_-google-_-lia-_-219-_-interiorstains-_-999914411-_-0&store_code=2545&gclsrc=aw.ds&&gclid=EAIaIQobChMI65yMi-jz5AIVPv_jBx2gnAGMEAQYBSABEgK0UPD_BwE
And then the stain is whatever you want, I did dark walnut
https://www.homedepot.com/p/Varathane-1-gal-Dark-Walnut-Classic-Wood-Interior-Stain-340614/305502034?cm_mmc=Shopping%7CG%7CVF%7CD24%7CMulti%7CVARATHANE%7CPLA%7CPaint%7CVarathane_INT_Liquids_Smart|71700000043732766|58700004596122067|92700038640637724&gclsrc=aw.ds&&gclid=EAIaIQobChMInvGdy-jz5AIVCr7ACh23JQY7EAQYASABEgIIWfD_BwE
That height is correct. The KARLBY is 1 1/2" thick. So the top of the desk is 29". My old desk was 31 1/2" high so I was skeptical about loosing the few inches as well. But I can honestly say I much prefer the height of the IKEA build now that I'm used to it.
Also you can always use something to make it higher if you don't like it. I've seen a few IKEA builds use these to make increase the height. Here is a Reddit post where the person has these legs
I’m also 5’10” and I fit in just fine. I went from having the IKEA Linmon desk and it was almost the exact height as this one so I’m already used to it. If height is a problem for you I would recommend ordering some adjustable metal legs like for furniture. A lot of people are using these to put between the desk and cabinets to raise it up a little bit, and plus they make it look a bit nice imo. VOVOV Furniture Cabinet Metal Legs Adjustable Stainless Steel Kitchen Feet Round Black and Silver 50 x 50mm Pack of 4 + 16x Screw https://www.amazon.com/dp/B01NCKZRTL/ref=cm_sw_r_cp_api_i_HVysDbDZYE9PG
I would advise you to forget about attaching it to the wall and instead put some real furniture legs on that piece of furniture. IKEA's CAPITA legs will probably do the job http://www.amazon.com/IKEA-CAPITA-Leg-Stainless-Steel/dp/9178881986/ref=lp_511274_1_15?s=hardware&ie=UTF8&qid=1459220311&sr=1-15
The real problem isn't attaching it to the wall, but rather that your existing supports kinda suck.
2) If you must attach it to the wall, once it is on some good supporting furniture legs, drywall screws placed into a stud will work exceptionally well. However I doubt this will really be necessary if you get some good legs on it.
I found them!
They look perfect. Thanks. Now I just gotta rip everything off my desk and put them on. Hmph.
Whoops! Can't believe I completely looked over that haha. I'll update the post.
I ordered 5 legs in total, 4 as a set and an additional thicker one for support in the middle of the back of the desk.
The set of 4 legs was "Black Adjustable Table Leg Set - Set of 4": https://www.amazon.com/gp/product/B001DSZVTI/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
And the 5th leg was "28" Tall Office Height Table Leg - Matte Black": https://www.amazon.com/gp/product/B000WIXH8M/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
So could i use something like this for the legs to help level?
4 pack of 2000 Lb. Capacity Heavy Duty Leg Levelers
74" butcher block counter top from Home Depot.
Antique Walnut stain with satin finish.
Legs are here.
Center leg (plus a 1/2 inch wooden brace) is [here.]
(https://www.amazon.com/gp/product/B000WITW86/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1)
Built in monitor stand and charging port are here and here.
I'll have a full size midi keyboard underneath the monitor soon, and will drill a grommet hole for the keyboard and mouse cables to travel through - so that they can run beneath the desk and not over/under the piano.
And I'll probably get some LED since that seems popular. And replace the banana stand with a real headphone stand, lol.
I used these. They work great!
I used these for center support :) That's the way to do it.
VOVOV Furniture Cabinet Metal Legs Adjustable Stainless Steel Kitchen Feet Round Black and Silver 50 x 50mm Pack of 4 + 16x Screw https://www.amazon.com/dp/B01NCKZRTL/ref=cm_sw_r_cp_apa_i_c0UwDb7V8HY8N
Not OP, but you can find hairpin legs pretty much anywhere these days. Here's a set on Amazon.
Good point. That sparked my curiousity, so I went on Amazon and found these: https://www.amazon.com/Heavy-Duty-Leveler-Wide-Foot/dp/B0037MK8XC#productDetails
I feel ya. For what it's worth, the door was just a plain flat thick piece of wood, no holes for a door knob or anything like that. It's quite robust, went with these legs for it.
Just a thought for ya.
They are not from ikea.
https://www.amazon.com/dp/B01NCKZRTL?ref=ppx_pop_mob_ap_share
​
As for the install... I screwed mine into the tops of the alex drawers and put a small piece of double sided 3M tape on the top of each leg. I have a 98" top with a lot of equipment on it, so im comfortable with it not fully being bolted to the top, it really doesnt move at all.
I think Ikea has some, but maybe something like this https://www.amazon.com/VOVOV-Furniture-Cabinet-Adjustable-Stainless/dp/B01NCKZRTL/ref=sr_1_5?keywords=4+furniture+legs+steel&qid=1570707326&sr=8-5 ?
/u/Romeo-X you rock!! I know the price is absurd. But you got me looking in the right spots. For anyone else in need they seem to be sold on amazon.com and ship to Canada: https://www.amazon.com/Ikea-Capita-Stainless-Steel-Legs/dp/B00DGRYI48
Thanks a million random redditor!
These for the turntable. https://www.amazon.com/Nobsound-Aluminum-Speakers-Isolation-Amplifiers/dp/B07K9ZYP84
These for the Kallax. https://www.amazon.com/gp/aw/d/B01NCKZRTL?psc=1&ref=ppx_pop_mob_b_asin_title
My toddler loves to run around the house and this combination helped me dramatically with my skipping issues.
Ikea sells similar ones, but it looks like the risers in OP's photo are these ones.
Hello, not OP, but they are something like these I believe.
​
https://www.amazon.com/gp/product/B00KQH8HMU/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
https://www.amazon.com/dp/B01NCKZRTL/ref=cm_sw_r_other_apa_i_8CIRDbPKTQ0E7
Thanks. Got these on Amazon.
Ikea Capita Legs are popular: https://m.ikea.com/us/en/catalog/products/art/60263574/
Others on Amazon: https://www.amazon.com/dp/B01NCKZRTL/ref=cm_sw_r_oth_api_G7KVBbXT06DCJ
https://www.amazon.com/dp/B00KQH8HMU/ref=cm_sw_r_oth_api_Z8KVBbDM4Y4N2
I found a cheap used table online and ordered these hairpin legs from Amazon. Heres a update picture. I just sanded it down and put on a new coat earlier today so it's not quite finished. But it's a major upgrade for cheap. You could definitely add some hairpin legs on your current tables for a quick DIY upgrade.
Leveling feet designed for an aquarium will have no problem holding that kind of weight, but they are difficult to install if your stand doesn't already have them. Wooden shims are cheaper and easier, lay down your plywood base first, then level the tank on top of the plywood.
Do not use these style that mount on the side of the legs/stand as they will rip out of plywood or MDF easily.
How about some leveling legs?
These have brackets that would make them easy to attach to your bookshelf.
http://www.amazon.com/gp/aw/d/B0035Y5XUK/ref=mp_s_a_1_4?qid=1426555747&sr=8-4&pi=AC_SX110_SY165_QL70&keywords=leveling+foot
BQLZR Stainless Steel Kitchen... https://www.amazon.com/dp/B00KQH8HMU?ref=ppx_pop_mob_ap_share here you go (:
I use the Capita legs on mine. This looks more like what OP has though.
Hey OP, i came across this which may help you
https://www.youtube.com/watch?v=mBeTm723xFs
He links to the legs he used in the description, they are here - https://www.amazon.com/gp/product/B00KQH8HMU/ref=as_li_tl?ie=UTF8&tag=i0698-20&camp=1789&creative=9325&linkCode=as2&creativeASIN=B00KQH8HMU&linkId=474da406e3943f49980ac15715cf8c5f
SMARTSTANDARD 28" Heavy Duty... https://www.amazon.com/dp/B072R2PNX3?ref=ppx_pop_mob_ap_share
Essentially it's just a nice piece of wood attached to some of these and finished. As for the shelves it's just some trim boards from home Depot I had laying around.
>...aside from the bose tulip stands...
Here are some frugal tulip stands.
Your speakers weigh roughly 104 pounds each. Searching for "plant stands," "coffee table base," or "table base" provides interesting results. Attaching table legs to a wood plank is a no brainer.
Even this looks cool.
I mounted these to my desk, then just gorilla double sided tape (the industrial stuff) my play 5's to them.
https://www.amazon.com/gp/product/B00DGRYI48/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
They're... not going anywhere ;P
Sure thing!
Countertop
Drawer
Legs
The desktop is an Ikea Karlby kitchen countertop. It's sitting on top of 2 Ikea Alex drawers and I used some furniture legs you can get on amazon for cheap as the lifts.
https://www.ikea.com/us/en/catalog/products/70335212/
https://www.ikea.com/us/en/catalog/products/10192824/
https://www.amazon.com/VOVOV-Furniture-Cabinet-Adjustable-Stainless/dp/B01NCKZRTL/ref=pd_sbs_60_1?_encoding=UTF8&pd_rd_i=B01NCKZRTL&pd_rd_r=J5N6CJZBVHEDD9ZZKN99&pd_rd_w=QJghL&pd_rd_wg=aFD2C&psc=1&refRID=J5N6CJZBVHEDD9ZZKN99
Are they like these?
https://www.amazon.com/dp/B00WWPVXK2/ref=cm_sw_r_sms_apa_i_qgHWDbXB3MH6F
https://www.amazon.com/BQLZR-Stainless-Kitchen-Adjustable-Furniture/dp/B00KQH8HMU
Probably something like these
The Container Store is a store that sells home organization stuff; IMO, it's an IKEA without furniture.
Their desk legs. See their examples on that page.
Other desk leg from Amazon.
As for the suggestion I made, check out some of the ideas here:
http://sasayuki.com/laminate-countertop-desk/laminate-countertop-desk-superb-diy-do-it-yourself-search/ (random website I found with a few 'countertop' desk examples) Note the example where they added a matching keyboard tray.
I mean, you really just need to find a suitable surface and then whatever you want that's the right height to use for legs. If you have the budget, you could even get a motorized sit/stand desk frame and attach whatever top to it you want.
They're these, which I've seen be popular on here: https://www.amazon.com/gp/product/B01NCKZRTL
But I didn't like the metal look so I wrapped the metal parts in this to match the drawers: https://www.amazon.com/gp/product/B078W57WGY
This is what you want, but a gate leg table would work just fine. If you're concerned about stability you can always put two legs on the table.
yeah bro its the ikea linnmon desk with two alex drawers https://www.ikea.com/us/en/p/linnmon-alex-table-white-s59932698/
and i also added these stands to the drawers to raise the tabletop up a little https://www.amazon.com/gp/product/B00KQH8HMU/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1
How much are you willing to mod it?
[Leveling feet] (https://www.amazon.com/dp/B0037MK8XC/ref=asc_df_B0037MK8XC5110807/?tag=hyprod-20&creative=395033&creativeASIN=B0037MK8XC&linkCode=df0&hvadid=198095900368&hvpos=1o3&hvnetw=g&hvrand=16877040462279695856&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9027240&hvtargid=pla-319952916403) and a 2 x 4 should do just fine
The raisers are these: https://www.amazon.com/gp/product/B00KQH8HMU/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1
I've had the desk for maybe 8 months and I haven't noticed any sag or any abnormalities. I've very pleased with how the desk is holding up so far. I had the IKEA Linnmon before this and my monitor stand would always leave a dent where it was being placed and with desk, there's no dent.
Monitor: Dell AW3418DW
Keyboard: Vortex Race 3
Mouse: Logitech G703
Karlby + Alex drawers combination
Lamp from Amazon
Furniture legs to raise up height of the desk
SKADIS Utility board from IKEA
PC:
NZXT H200, i7-8700k, X52 Kraken, 18GB 3200Mhz Trident Z RGB Ram, Evga 2080Ti, 650W PSU
Pictures of PC here
Logitech z33 2.1 Speakers
These, and they've worked out alright so far.
Ah that makes sense. I'm planning to use some 4 in legs to give my desk some extra height. https://amzn.com/B00KQH8HMU If I don't bolt the braces into the Aleks drawers, do you think sagging will be a problem? Thanks!!
Oh those are just kitchen legs from amazon
https://www.amazon.ca/BQLZR-Stainless-Kitchen-Adjustable-Furniture/dp/B00KQH8HMU/ref=asc_df_B00KQH8HMU/?tag=googleshopc0c-20&linkCode=df0&hvadid=292948034357&hvpos=1o2&hvnetw=g&hvrand=12992890320284480019&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9000671&hvtargid=pla-349478070909&psc=1
try amazon for the capitas
I bought them on amazon. Here is a link: https://www.amazon.com/Signstek-Three-Rod-Hairpin-Vintage-Coffee/dp/B01LVTW8JB
Note: When I bought them, they had one of those 'click for $5 off' coupons. That appears to be gone now.
Got them from Amazon. If you search for “hairpin legs,” you’ll find many other styles online.
There are plenty of heavy-duty leveling feet. E.g. these ones claim to support 2000 lbs per foot.
If you're worried about catching you could bevel the leading edge slightly.
No problemo, here you go.
They are adjustable but they work nicely for me at the lowest height.
They are available on amazon, but expensive...
https://www.amazon.com/dp/B00DGRYI48/ref=asc_df_B00DGRYI485359706/?tag=hyprod-20&creative=395033&creativeASIN=B00DGRYI48&linkCode=df0&hvadid=193166724913&hvpos=1o1&hvnetw=g&hvrand=13439013181184893743&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9014984&hvtargid=pla-307085826667
You can use thr Capita legs from IKEA, or [these](http://www.VOVOV.com/ Furniture Cabinet Metal Legs Adjustable Stainless Steel Kitchen Feet Round Black and Silver 50 x 50mm Pack of 4 + 16x Screw https://www.amazon.com/dp/B01NCKZRTL/ref=cm_sw_r_cp_apa_i_-dDlDb0QNS036) from Amazon since they're half the height
https://www.amazon.com/gp/aw/d/B071W8DCM2?psc=1&ref=ppx_pop_mob_b_asin_title
Found them. Wasn't as hard as I thought it would be.
https://www.amazon.com/BQLZR-Stainless-Kitchen-Adjustable-Furniture/dp/B00KQH8HMU/ref=sr_1_1?keywords=BQLZR&qid=1566188661&s=gateway&sr=8-1
https://www.amazon.com/VOVOV-Furniture-Cabinet-Adjustable-Stainless/dp/B01NCKZRTL/ref=sr_1_30?keywords=silver+couch+legs&qid=1565704323&s=gateway&sr=8-30
https://www.amazon.com/VOVOV-Furniture-Cabinet-Adjustable-Stainless/dp/B01NCKZRTL/ref=sr_1_8?crid=14R384LY8XMQS&keywords=cabinet+feet+adjustable&qid=1565299864&s=gateway&sprefix=cabinet+feet%2Caps%2C172&sr=8-8
These are the ones I have
Set of 2 Ikea Capita Stainless Steel Legs https://www.amazon.com/dp/B00DGRYI48/ref=cm_sw_r_cp_apa_i_RAYsDb0XQNP33
BQLZR Stainless Steel Kitchen... https://www.amazon.ca/dp/B00KQH8HMU?ref=ppx_pop_mob_ap_share
Probably BQLZR Furniture Cabinet Metal Legs Adjustable Stainless Steel Kitchen Feet Round Black and Silver 50 x 50mm Pack of 4 https://www.amazon.com/dp/B00WWPVXK2/ref=cm_sw_r_cp_apa_i_X2IxDb6208S6Z
Personally, I'd just grab a set of leveling legs.
I can't quite visualize what you are looking for, but I know that some people build a shelf/stand using these.
Set of 2 Ikea Capita Stainless Steel Legs https://www.amazon.com/dp/B00DGRYI48/ref=cm_sw_r_cp_apa_i_SDZvCb2WM6H08
Here
BQLZR Stainless Steel Kitchen... https://www.amazon.com/dp/B00KQH8HMU?ref=yo_pop_ma_swf
I’ve been considering building a workbench with https://www.amazon.com/Rok-Hardware-Capacity-Adjustable-Furniture/dp/B01N4BUE1P and https://www.amazon.com/SPACECARE-Swivel-Caster-Polyurethane-Bearing/dp/B07K2S25D3
Probably using this friendo i use the longer ones for my desk. https://www.amazon.com/dp/B00WWPVXK2/ref=twister_B01MU4ZRXR?_encoding=UTF8&psc=1
A lot of people use risers like these
Rok Hardware 4 Pack Heavy Duty 8000 LB Capacity Adjustable Furniture Leg Leveler https://www.amazon.com/dp/B01N4BUE1P/ref=cm_sw_r_cp_api_i_gsCACbY99EXWS
Oh, that's right. I forgot they only sell one kind of desk... /s
For those that also wanted to know, it actually appears to be the Karlby countertop combined with two Alex drawer sets and then with some risers (probably these but maybe these as pointed out by /u/unsupportive-tech) all combined to make the desk, which is not a product all in itself (at least it wouldn't seem that way.
https://www.amazon.com/BQLZR-Stainless-Kitchen-Adjustable-Furniture/dp/B00KQH8HMU
I got you my friend
Non-mobile: http://www.amazon.com/dp/B0035Y5XUK/ref=mp_s_a_1_4?qid=1426555747&sr=8-4&pi=AC_SX110_SY165_QL70&keywords=leveling+foot
^That's ^why ^I'm ^here, ^I ^don't ^judge ^you. ^PM ^/u/xl0 ^if ^I'm ^causing ^any ^trouble. ^WUT?
https://www.amazon.com/gp/aw/d/B071W8DCM2?psc=1&ref=ppx_pop_mob_b_asin_image
https://www.amazon.com/gp/product/B01NCKZRTL/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1
Here. but it's on amazon.ca
https://www.amazon.com/gp/product/B00KQH8HMU/ref=oh_aui_detailpage_o07_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B071W8DCM2/ref=oh_aui_detailpage_o07_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B00KQH8HMU/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B00KQH8HMU/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/aw/d/B00KQH8HMU?psc=1&ref=ppx_pop_mob_b_asin_title
https://www.amazon.com/gp/product/B00KQH8HMU/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
Another example, but not at this price, haha... and doesn't need to be angled.
https://www.amazon.com/gp/product/B00DGRYI48
This
I found them on amazon. These things are seriously heavy duty and a fraction of the price of other levelers. They have a hex head on the top of the screw. Couldn't be happier.
http://www.amazon.com/Heavy-Duty-Leveler-Wide-Foot/dp/B0037MK8XC/ref=pd_sim_hi_6?ie=UTF8&refRID=1F75J66434J8P08ZBMZJ
http://www.amazon.com/gp/product/B001DSZVTI
Eight screws per leg and it's rock solid.
They make rubberized feet that'll fit on a 4x4 table leg. I think my father grabbed these at a local wood working store, but I bet Home Depot or Lowes would offer something.
Pic of my table showing what I'm talking about.
https://www.flickr.com/gp/64462769@N06/jCrn97
​
Or you could grab a heavy duty leveler... but it may not look as nice since it'll be visible.
https://www.amazon.com/Rok-Hardware-Capacity-Adjustable-Furniture/dp/B01N4BUE1P/ref=pd_lpo_vtph_60_bs_img_1?_encoding=UTF8&psc=1&refRID=BKJ2ZYVMXNJSNRCRKW4J
​
Mousepad - https://www.pcgamingrace.com/products/glorious-3xl-extended-gaming-mouse-pad-24x48#
PC Specs - https://pcpartpicker.com/list/Pvp6tJ
The metal spacers - https://www.amazon.com/gp/product/B00KQH8HMU/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
The spacers are screwed into the tops of the alex drawers with some small screws, and the desktop just sits on top and its heavy enough it doesnt move.
​
These ones are the ones I got https://www.amazon.com/dp/B00KQH8HMU/ref=olp_product_details?_encoding=UTF8&me=
Yes Exactly. I screwed them to the top of the Alex drawers, they even came with the screws.
Yea no worries, here you go
BQLZR Stainless Steel Kitchen Adjustable Feet Round 2" Dia Furniture Leg Pack of 4 https://www.amazon.com/dp/B00KQH8HMU?ref=yo_pop_ma_swf