Reddit mentions of Elenco Practical Soldering Project Kit

This. You can find decent starting irons on Amazon with solder. You might consider buying a few ”learn to solder" soldering kits from Amazon. They come with all the parts needed, and the instructions teach you how to assemble the components (you then have to solder them in the board it came with)

Iron set example: (good for basic /beginner projects) https://www.amazon.com/gp/aw/d/B01H1IFT54/ref=mp_s_a_1_4?ie=UTF8&qid=1523313329&sr=8-4&pi=AC_SX236_SY340_FMwebp_QL65&keywords=soldering+kit&dpPl=1&dpID=51rAt23O28L&ref=plSrch

Electronics kit beginner example (these are fun to do imo)

https://www.amazon.com/gp/aw/d/B0002LUAL6/ref=mp_s_a_1_2?ie=UTF8&qid=1523313465&sr=8-2&pi=AC_SX236_SY340_QL65&keywords=elenco+soldering+kit&dpPl=1&dpID=519bj4ev-jL&ref=plSrch

For a soldering kit, I used this one on amazon, it was great practice.

As for a soldering iron, look on ebay/amazon for a "936" soldering iron. Any of them are about the same, most are clones of the famous hakko 936.

The original 936 is too expensive in my opinion, I'm using a sparkfun clone 936 that unfortunately is no longer sold. Most of the other clones should be ok though.

The only think I would really recommend getting legit is a hakko chisel tip, like this one. Don't get those 10pc tip sets, they are cheap and it is much better to use just one good tip than a bunch of bad tips.

Lastly, if you want your tip to last a longer time, don't use a wet sponge, that can damage your tip. Use one of those copper hard brush things, I forget what they are called, but you can buy them at amazon/ebay.

I would start by doing one of these practice kits to brush up on soldering. They come with instructional booklets. As for mods just figure out one you'd like to do and go for it. AV mods tend to be pretty simple. Further reading:

MMMONKEY

Console 5

Just to add onto this, I used this kit as my first project before soldering Game Boys, and it helped a ton. It comes with an instruction booklet explaining how to solder, strip wires, mount 555 timers and resistors, etc. It even has an unused part of the board you can practice on.

Something along these lines would be a good place to start, just to get more comfortable with soldering in general: https://smile.amazon.com/gp/aw/d/B0002LUAL6

Or honestly, any other kit that looks interesting to you on Amazon, Adafruit, Sparkfun, etc.

Specifically for mechs, grabbing some switches from a switch tester and playing around with small boards like these could be a good follow-up step to get direct experience with what you'd be doing when assembling your own board:

• http://techkeys.us/collections/accessories/products/the-enabler
  
• http://techkeys.us/collections/accessories/products/techkeys-keyboard-business-card
  
  Hope that helps.

Cool project. The soldering should be pretty simple, and it's fairly easy to learn. I would recommend buying a soldering project kit, something silly like this: amazon link that you don't mind messing up and learning on.

If after reading these comments, you decide to learn to solder, here's a simple $8.59 kit that I recommend. Iron not included.

I used this one. It also has you intentionally foul up a few joins so that you can learn to properly fix them.

https://www.amazon.com/gp/aw/d/B0002LUAL6/ref=mp_s_a_1_1?ie=UTF8&qid=1482521154&sr=8-1&pi=SY200_QL40&keywords=solder+practice+kit&dpPl=1&dpID=519bj4ev-jL&ref=plSrch

This is the one I used.

I'm in the same boat so I got a practice soldering kit from Amazon for $11. http://www.amazon.com/gp/aw/d/B0002LUAL6/ref=sr_ph_2?qid=1463770366&sr=sr-2&pi=AC_SX236_SY340_QL65&keywords=soldering+kit

Hey bud, I think it's great that you're interested in this hobby and am happy you're doing some research before plunging in. Do you know how to solder yet? That's an important skill in building your a drone since nearly everything in the building phase will require it. I had to start out with a little soldering practice kit before I started building a quadcopter. Soldering with a quadcopter can be difficult because everything is so small!

If you've got soldering down though, and you want a good starting kit that comes with pretty much everything, you can find some on eBay for pretty good prices, I've built four ZMR250 DIY kits purchased on eBay over the last couple years and they've all flown great. (That kit isn't totally complete though, you'll still need a transmitter/receiver and batteries.)

That kit is about £61, you can get a FlySky FS-T6 transmitter which comes with the receiver for £35 which leaves you over £50 to cover a couple batteries, a LiPo Charger, other misc electronics/parts you might need like voltage regulators or connectors and shipping. (which might end up being a little over £150, but that's how this hobby tends to go..)

Hey! I actually had very little knowledge of drones/electronics, and then I started lurking on this subreddit and became inspired! I did a bunch of research first, which pretty much consisted of watching build videos and googling "how do I build a quadcopter". I made sure to google any words or lingo that I didn't understand, like "what is an ESC", and "how does a flight controller work". I also tried to search this subreddit for things like "what flight controller should I use" and watched a lot of build videos.

Once I had a decent understanding of the basic parts and components, I bought a toy grade RFT quad, flew/crashed it, and took it apart to look at the various components. I also decided at that point that I wanted a deeper understanding of electronics, and bought this book, though I think that step is highly optional and not required to build a quad. I started working through the book, and also bought this soldering practice kit. After completing the practice kit, I felt more or less ready to try to build this tiny whoop.

Since this was my first build, I tried to keep it simple. It really just consisted of some very easy soldering and then putting the rest of the parts onto the frame. If you'd like more specific instructions or explanations of anything I did, let me know! I think this build could definitely be accomplished by anyone with a desire to learn. I learned a lot along the way, and I'm already planning a bigger more complicated build.

I suggest this:

http://www.amazon.com/Elenco-Practical-Soldering-Project-Kit/dp/B0002LUAL6/ref=sr_1_4?ie=UTF8&qid=1406761425&sr=8-4&keywords=learn+to+solder+kit

It's a very good kit, and will give you plenty of practice before you solder your Poker 2. No frills, and will give you plenty of practice for through hole soldering.

Combine this with a practical, but good quality soldering station:

http://www.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC/ref=sr_1_3?s=power-hand-tools&ie=UTF8&qid=1406762091&sr=1-3&keywords=soldering+iron

A desoldering pump:

http://www.amazon.com/Sucking-Vacuum-Desoldering-Solder-Remover/dp/B005GIPKOW/ref=sr_1_3?s=hi&ie=UTF8&qid=1406762167&sr=1-3&keywords=desoldering+pump

And some solder:

http://www.amazon.com/Alpha-AT-31604-60-40-Solder-Ounces/dp/B00030AP48/ref=sr_1_1?s=power-hand-tools&ie=UTF8&qid=1406762345&sr=1-1&keywords=solder

To learn, there are plenty of Youtube videos, I recommend you also solder the Elenco kit, then desolder everything to get a feel for how the desoldering pump works (it's super easy, you can't really screw it up). Then, solder it together one more time for extra practice.

All together, about $66 bucks. Add in the cost of the switches, and you're looking at a little over 100. Still a bunch cheaper than the Poker 2 from Massdrop ($143.50), and you've just learned a life skill. For me, that's totally worth it, but then again, I'm an engineer, and learning useful skills is what my entire profession is based on.

---

EDIT: Get this soldering kit instead:

http://www.amazon.com/Elenco-SP3B-Practical-Soldering-Project/dp/B0002LUALG/ref=pd_tcs_compl_t_3?ie=UTF8&refRID=00RQRQTCJ767WDS4D7KV

Cheaper and has more soldering points. The other one has a shitty speaker which doesn't add much to the soldering lesson, but drives the cost up.

Get something like this to learn the basics:
http://www.amazon.com/Vintage-Sports-Cards-MX-906-Electronic/dp/B00005K2SY/ref=sr_1_1?s=toys-and-games&ie=UTF8&qid=1313696934&sr=1-1

The various parts in there will be useful when you start breadboarding stuff.

and this to learn soldering:
http://www.amazon.com/Elenco-Practical-Soldering-Project-Kit/dp/B0002LUAL6/ref=sr_1_4?s=toys-and-games&ie=UTF8&qid=1313696934&sr=1-4

You might have a local hackspace where people would be willing to help you out if you are having trouble with the soldering.

http://www.amazon.com/Elenco-Practical-Soldering-Project-Kit/dp/B0002LUAL6/ref=sr_1_6?ie=UTF8&qid=1324164212&sr=8-6