Best products from r/AutoDetailing

We found 389 comments on r/AutoDetailing discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 1,452 products and ranked them based on the amount of positive reactions they received. Here are the top 20.

Top comments mentioning products on r/AutoDetailing:

u/jauntworthy · 4 pointsr/AutoDetailing

I've always struggled to keep my vehicles clean because 1) they were always old, 2) I've lived in condos, 3) car washes did a terrible job / detailers charged too much, and 4) I didn't realize you could do all of this yourself pretty effectively.


When I bought a new truck at the beginnging of the year, I randomly stumbled upon an Ammo NYC video and the nerd / clean-freak was intrigued. A couple dozen videos later, and I was hooked. Shout out to Larry for your passion - thank you for the insane amount of information on your channel. (Wish I could afford all of your products, or that you had some of them on Amazon!).

Living in a condo, I have to swing by my local coin wash and take up a bay with a few buckets during off-peak hours, but I've gotten it down to 1.5 hours and looking like this every time.

I've only been doing this for a few months, but thought I'd share the products I've researched and selected based on reviews and costs. Hope this helps save someone time!

TOOLS

  • McGuire-Nicholas 22015 15-Inch Collapsible Tote - https://amzn.to/2HXGsvd - I love this thing. Handle is sturdy and holds every chemical I need.
  • Relentless Drive Ultimate Car Wash Mitt - https://amzn.to/2KJC7td - Great mitt and would strongly recommend it. I've only used the mitt for a few washes so I can't comment on durability, but if I had to guess I think it's going to hold up. My only complaint is that it's so voluminous that it's difficult to rinse / wring out the dirt when using the two-bucket method. Not a big enough problem to look for another mitt, though.

    BUCKETS

  • Chemical Guys ACC_101 Detailing Bucket Kit - https://amzn.to/2KJb552 - a good starter bucket, but it's worth calling out how much of this stuff is BS marketing: the bucket is only 4 gallons, the gamma lid can be bought for cheaper on amazon, the citrus gloss is OK, and the wash mitt is worthless / isn't going to hold up. I barely used the mitt once and fuzz falls off constantly when handling.
  • Adam's Grit Guard Wash Bucket with Lid - https://amzn.to/2IoSflo - Better value than chemical guys, but the bucket is just a regular bucket ($4 at Home Depot) and the gamma lid can be purchased for $10-15 on Amazon. I'm not convinced grit guards are worth it, but more on that later.
  • Grit Guard Washboard Bucket Insert - https://amzn.to/2HW4juZ - the product is well made and does what it's intended to do, but I'm skeptical of its value. Yes, rubbing your mitt on a washboard would intuitively get dirt to fall off, but is it actually more effective than using your hands (which you do anyway to wring out the mitt)? And I'm not buying that the fins "trap dirt." Anybody who looks at their rinse bucket while washing wheels for example can plainly see the water's black. Dirt's floating everywhere.


    CHEMICALS

  • Mothers 08216 California Gold Instant Detailer - https://amzn.to/2KJ2f7t - this stuff has done a pretty good job for quick wipe-downs, spot cleans, etc.
  • Griot's Garage 11108 Window Cleaner - https://amzn.to/2Iq5CSF - The spray bottle itself is awesome and works really well. The solution also seems to work well, though I've only ever used it after washing the truck and so I'm not sure how much it helps.
  • Meguiar's G3626 Ultimate Waterless Wash & Wax - https://amzn.to/2jFg3DJ - I used this a few times with the microfiber directional pass method after some serious pollen clouds invaded Austin, and it worked surprisingly well. Ran through 3-4 towels to do my entire truck, then spot-cleaned with an instant detailer. Even though wheel wells and a few pieces were still dirty, it was a huge improvement without the hassle of a full wash. Will definitely be using this as my in-between wash method.
  • Chemical Guys V7 High Gloss Spray Sealant and Quick Detailer - https://amzn.to/2HXiQ9R - I'm new to detailing, but this stuff is probably the most impressive chemical of everything I've used. The combination of a damp microfiber + V7 produces the result everyone thinks about when they think about car washes: a clean car with no streaks or water spots. Wringing out my microfiber towel can get old, but the end result is just awesome.
  • Chemical Guys Citrus Wash and Gloss - https://amzn.to/2I1knvx - I don't have the luxury of a frother right now, but from simply adding some in a bucket and using a power washer to generate suds, I get decent foam and the soap seems to work well. That said, it's not earth-shattering and I will probably try other washes when I run out.


    INTERIOR

  • Mothers 06512 All-In-One Leather Care - https://amzn.to/2IlawAg - This stuff works great and smells even better.


    WHEELS

  • Adam's Deep Wheel Cleaner - https://amzn.to/2K09l6f - The spray bottle is terribly difficult to press and I always end up using way more than I want. I'm not confident I need to use this instead of just using soap. Maybe it's for exceptionally dirty cars or those with tons of brake dust, but I'm rarely in either camp so I may not buy some more after I run out.
  • Adam's Hex-Grip Pro Tire Dressing Applicator - https://amzn.to/2HYtb5y - Works well and easy to handle.
  • Mothers Wheel Brush - https://amzn.to/2K0Ky1Y - really like how easy this is to handle and how soft the bristles are. Highly recommended.
  • Optimum Opti-Bond Tire Gel - https://amzn.to/2KJsxGP - This is a good low-gloss gel, though I need to try additional coats to see if I can get those tire shinier.
  • ABN Car Wheel Rim Cleaning 3-Piece Kit - https://amzn.to/2KFgSIR - Yes the big woolie has good reach and allows you to clean the inside of your rims effectively, but the handle is annoyingly difficult to hold after it becomes saturated / heavy to hold.


    TOWELS

  • Chemical Guys Professional Grade Premium Microfiber Towels, Gold - https://amzn.to/2HY8Q0a - these things are outsidanding and are a great value. Definitely watch Larry's video on microfiber care, which fixed all of my annoyances with microfibers accruing fuzz in the dryer.
  • THE RAG COMPANY EAGLE EDGELESS 500 Korean 70/30 Super Plush 500gsm Microfiber Detailing Towels - https://amzn.to/2HYVmky - very high plush and high quality, though I end up using the Chemical Guys towels more often and save these for random spot details. Probably not ideal.
  • THE RAG COMPANY Premium Window, Glass, Mirror & Chrome Korean 70/30 Microfiber - https://amzn.to/2rrveVg - work great for cleaning windows and mirrors.
  • Nylon Laundry Bag - https://amzn.to/2rtYOcP - I have one bag for clean and one for dirty. Has done a great job of keeping dust off the rags during storage.
u/LagunaGTO · 31 pointsr/AutoDetailing

Overview

Here is my work from this last weekend. I am a completely mobile detailer and live in the Chicagoland area. I do not actually open until May but this client reached out to me and I wanted to make sure they were taken care of properly and establish a good relationship.

This detail was a lot of fun. I always enjoy interiors because they are such a huge turn around for not as much work as something like a full-blown paint correction.

The client had brought his car to a bodyshop to have it repainted. Unfortunately, while the windows were removed from the vehicle, they were not covered. This resulted in the work of the body shop making its way into the vehicle and covering it. This vehicle is definitely this client's baby and fun car. He was absolutely devastated and really wanted his vehicle brought back to life so he could once again enjoy something he has put a lot into.

I look forward to potentially working on this vehicle again and helping this owner get his car to any level of perfection he is looking to achieve.

---

Work Done

The client wanted a Definitive Interior Cleaning as well as a Showroom Engine detail. Services described here

To a great help to me, this client removed the seats and cleaned them all before I even came on site. This allowed me to focus a lot more time on the interior and door jamb areas and the engine. We did not put the seats back into the vehicle as I wanted the fabric coating to fully dry before they were put back in. That is why you will not be seeing any seat pictures. They were just fine.

The interior was vacuumed and then was completely cleaned with Detailer Pro's Total Interior Cleaner. This product is my go-to for interiors. It works flawlessly and it has a great smell that does linger and just smells naturally clean. I use these types of interior clothes for working with that product.

To assist in cleaning some of the interior trim and the vents, a steam cleaner was used. The steam cleaner was very carefully used on the headliner as well. It is very important to not let a headliner get soaked or too wet as the glue is very thin. Doing this can cause headliner sag.

Nothing beats cleaning the interior of a vehicle with this brush. It is absolutely my favorite brush.

All interior hard surfaces were treated with Lexol Premium Protectant.

The entire interior carpet was cleaned utilizing a heated carpet cleaner. The entire interior carpet where feet will be, the two front seats, and all four mats were treated with CarPro Cquartz Fabric Coating.

The pedals were cleaned up with steel wool as much as possible. Lots of plastic on them which made it difficult to polish to the level it could have been.

All door jambs were sealed with Sonax Polymer Net Shield.

The engine was completely cleaned using P21S Total Auto Wash and just general microfiber clothes from a place like AutoZone. The engine was then dressed with Adam's In&Out Spray to enhance the appearance of all plastic/rubber parts.

---

Response

Overall the client was very satisfied and could not stop staring at the vehicle.

He stated that it looked like new again and like a completely different car. He definitely seems ecstatic to have his vehicle back to the way it should be.

The client did point out the spots still left on the headliner and was instructed on properly cleaning that overtime to remove them. I expressed no issue/charge to work on the headliner again if I come out for new work.

---

Reflection and Lessons Learned

Not much for this one. I had a chance to finally clean a headliner that really needed it. It's definitely very difficult to clean something when you can't be that aggressive with and just have to take time and a lot of patience.

I got pictures of the interior beforehand, but not the engine. The engine was worse off than I was planning and without the use of water like normal, it took quite a bit of time. It turned out just fine though. Engines can be cleaned either way.

---

Total Time: 5 hours on interior, 2 hours on engine

Total Cost: $390

www.chicagosdad.com

www.facebook.com/chicagosdad

u/DaegenLok · 1 pointr/AutoDetailing

Hope this helps! This isn't an exhaustive list of the best professional products but some of the best top rated affordable and highly rated by forums and high subscriber YouTubers. I'll try to answer questions as they come. Thanks for all tye comments and positive/critical feedback. Promise is all helps in the end!

Wash/Decontamination

  1. Meguiar’s Gold Class Shampoo Car Wash - $23 - https://www.amazon.com/gp/product/B071HR14SJ/ref=ppx_yo_dt_b_asin_title_o07__o00_s04?ie=UTF8&psc=1
  2. Mothers California Gold Clay Bar System (Best out of the packaged kits compared to “professional” line expensive clays/lubes) - $16 - https://www.amazon.com/gp/product/B0002U2V1Y/ref=ppx_yo_dt_b_asin_title_o07__o00_s02?ie=UTF8&psc=1
  3. Carpro Iron X Iron Remover 500 ml with Sprayer - $19 - https://www.amazon.com/gp/product/B004UM6DLE/ref=ppx_yo_dt_b_asin_title_o03__o00_s00?ie=UTF8&psc=1
  4. CarPro Eraser Intense Oil & Polish Cleanser (Rated a little higher than Gyeon Prep – A few options out there but this is cheap and works great compared to straight IPA spray/wipe. It’s not rough on the clear coat and doesn’t cause issues with using higher % of IPA over time) - $17 - https://www.amazon.com/gp/product/B00FY0XY1S/ref=ppx_yo_dt_b_asin_title_o00__o00_s00?ie=UTF8&psc=1
  5. 2x Five-Gallon buckets with a dirt guard in the bottom. – Lowe’s $10-$15 with the dirt guard (already had that)

    Wheels/Tires
  6. CarGuys “Premium Wheel Cleaner” - $17 - https://www.amazon.com/gp/product/B014V9GFJU/ref=ppx_yo_dt_b_asin_title_o07__o00_s05?ie=UTF8&psc=1
  7. Mothers Mag & Aluminum Polish (Classic Product but you really won’t find a more reliable and top notch wheel polish than this – Here is Amazon link but usually you can pick this up cheaper at Walmart for about $4 or $5 I believe) - $7 - https://www.amazon.com/Mothers-05101-Mag-Aluminum-Polish/dp/B0009H519Y/ref=sr_1_3?ie=UTF8&qid=1549046381&sr=8-3&keywords=mag+and+aluminum+polish
  8. 1x 2.5 Gallon Bucket Dedicated To Wheel Cleaning ONLY – Lowe’s $5

    Compounding/Polishing
  9. Meguiar’s New m110 (Newer m105) Compound (Try To Find A 15% Coupon) - $40 - https://www.autopia-carcare.com/meguiars-m110-pro-compound.html#.XFRhIlVKhpg
  10. Meguiar’s New m210 (Newer m205) Finishing Polish/Swirl Remover (Try To Find A 15% Coupon) - $40 - https://www.autopia-carcare.com/meguiars-m210-pro-finishing-polish.html#.XFRhIVVKhpg
  11. 6x Pack Lake Country CCS Compounding/Polishing Pads – 3x Orange/2x White/1x Green – $60 (Try to find a usable 15% coupon) - https://www.autopia-carcare.com/ccs-pads.html#.XFRfgVVKhpg
  12. Meguiar’s PlastX Clear Plastic Cleaner & Polish (Using for rear/front light polishing – Could use your compound to polish as an alternative but I like the protection factor built into this plastic polish) - $5 - https://www.amazon.com/gp/product/B0000AY3SR/ref=ppx_yo_dt_b_asin_title_o05__o00_s00?ie=UTF8&psc=1
  13. Car Foam Drill Polishing Pad Kit - 22x Piece 3” Buffing Pads (Cheap drill adapter + pads for head/tail lights only – You could go with a legit company for 3” pads but for the cost it was a joke and they are only for head/tail lights, NOT paint) - $11 - https://www.amazon.com/gp/product/B076ZJMHB1/ref=ppx_yo_dt_b_asin_title_o04__o00_s00?ie=UTF8&psc=1


    Finshing Wax/Protectant/Plastic & Trim Restorer
  14. Meguiar’s Ultimate Liquid Wax - $16 - https://www.amazon.com/gp/product/B004HCM9H4/ref=ppx_yo_dt_b_asin_title_o07__o00_s05?ie=UTF8&psc=1
  15. TriNova Plastic & Trim Restorer (Hard Pressed to find anything as affordable for the ratings) - $13 - https://www.amazon.com/gp/product/B01AAZ1OAE/ref=ppx_yo_dt_b_asin_title_o07__o00_s00?ie=UTF8&psc=1


    Interior/Glass Cleaners
  16. 303 PROTECTANT: Interior & Exterior UV Protectant (Use it to wipe leather seats, dash, and plastics) - $10 - https://www.amazon.com/gp/product/B0185PU38A/ref=ppx_yo_dt_b_asin_title_o07__o00_s05?ie=UTF8&psc=1
  17. Invisible Glass Premium Glass Cleaner w/ EZ Grip (Awesome stuff) - $4 - https://www.amazon.com/gp/product/B00KAON5Q2/ref=ppx_yo_dt_b_asin_title_o07__o00_s01?ie=UTF8&psc=1


    Convertible Fabric Top Cleaner/Protectant/Sealer
  18. RaggTopp Fabric Convertible Top Cleaner/Protectant Kit (This is top in class. There aren’t really any other higher rated options. Go with kit that has cleaner/brush/protectant sealer.) - $50 - https://www.amazon.com/gp/product/B008MM5ZFI/ref=ppx_yo_dt_b_asin_title_o06__o00_s00?ie=UTF8&psc=1


    Microfiber Cloths/Car Drying Microfiber Cloths/Buffing Microfibers/Brushes/Etc.
  19. Zwipes Microfiber Cleaning Cloths (24-Pack) (**Found this on a couple lists online for high ratings and they are soft/Highly rated on Amazon and cheap!) - $13 - https://www.amazon.com/gp/product/B00ANZHG7C/ref=ppx_yo_dt_b_asin_title_o07__o00_s04?ie=UTF8&psc=1
  20. Chemical Guys Chenille Microfiber Premium Scratch-Free Wash Mitt (Might consider 2-3 of them for washing the top and bottom parts of car – prevent further scratching) - $7 - https://www.amazon.com/gp/product/B003TTL0TE/ref=ppx_yo_dt_b_asin_title_o07__o00_s04?ie=UTF8&psc=1
  21. Mothers Wheel Brush - $8 - https://www.amazon.com/gp/product/B001GJ3DZS/ref=ppx_yo_dt_b_asin_title_o07__o00_s04?ie=UTF8&psc=1
  22. Chemical Guys Microfiber Wash Cleaning Detergent Concentrate (Almost all the videos put this one as #1 compared to a couple other companies that offer dedicated microfiber wash detergent) - $10 - https://www.amazon.com/gp/product/B001TJXWH4/ref=ppx_yo_dt_b_asin_title_o04__o00_s00?ie=UTF8&psc=1
  23. Chemical Guys Woolly Mammoth Microfiber Dryer Towel (25 in. x 36 in.) - $25 - https://www.amazon.com/gp/product/B0042Z0LEO/ref=ppx_yo_dt_b_asin_title_o05__o00_s00?ie=UTF8&psc=1
  24. Other Random buffing foam applicators and microfiber cloths that came with some of the kits listed above. Will use those for compound wiping and etc.
  25. Plastic Containers For Organization – Hefty 1.625 (Microfiber container) & 3.75 (Other products w/o squirt triggers) Gallon Containers I believe are the ones in the picture. These are awesome considering the cheap pricing. The plastic is heavy duty and the lathes aer decent all things considered. - https://www.lowes.com/pd/Hefty-1-625-Gallon-6-5-Quart-Clear-Tote-with-Latching-Lid/1000505511

u/Fyrel · 7 pointsr/AutoDetailing

I'm reposting some suggestions I made from a previous similar thread, hope it works out for you (the last person's budget was $100; not sure what yours is, but you can pick and choose!)

 

Optimum No Rinse: Concentrated and capable of being diluted as a wash, quick detailer, clay lubricant, window cleaner, light interior cleaner, and more.

Optimum Opti-Seal: Incredibly easy to use sealant (wipe on and walk away!), can be used in place of RainX on windows, good drying aid, and useful as an interior dressing as well. Opti-seal ALL the things!

Detailing brushes: Because every detailer can use more brushes!

Nanoskin Autoscrub Sponge: Makes the process of decontaminating your paint much faster. Much longer life than clay and can be used even after dropped on the ground! Use the ONR as lubricant and you save tons of money.

The Rag Company Eagle Edgeless Towels, 4 pack: These will be the best towels he's ever used.

The total for all of this should be $97.96, just under your budget :)

 

A couple other suggestions if you want to mix and match:

Smaller Opti-Seal: Since it's the biggest budget item here and a little goes a long way, you can go with the small one to include more items in your bundle.

Adam's Wheel Cleaner: The least terrible smelling wheel cleaner, but extremely effective as well. Good if that truck throws a lot of brake dust.

CarPro PERL: For protecting exterior plastics as well as dressing them, and for use as a satin look tire dresing.

Wheel Woolies: Makes cleaning wheels a much nicer experience, and won't fling brake dust into your face like the brushes do.

Hope this helps! If you want any more specific recommendations for any category, feel free to ask! As for things to avoid, Armorall, Turtlewax and Chemical Guys in my opinion.

u/kmets4 · 2 pointsr/AutoDetailing

I would reccomend these materials for the two bucket wash method. Its probably the most common method, and one of the safest. There are plenty of youtube how to's on this. These are the materials you'll need.

  • Two buckets that will be used for the two bucket wash method. They can be purchased from a local home center for relatively cheap. $10
  • Grit Guards. Preferably two, in order to prevent grit from reentering the wash mitt. $20
  • Wash Mitt. Something like this will be just fine. $8
  • Car soap. This is completely up to you. Something like Meguiar's Gold Class is fine. $10

  • Wheel brush. Dependent on what you type of wheels you have. A quick amazon search will give you an idea. $10-20
  • Sealant. I use Meguiar's M21. Not the best not the worst. Im sure others will chime in an have recommendations for you. $20.
  • Wax. I don't use a wax because my car is older, and the sealant does just fine.

  • Microfibers. The Rag Company has some great starter kits.

    Not Necessarily essentials, but recommended.

  • Wheel cleaner. Something like Sonax. $15
  • Clay Bar. This will be used to intitially remove contaminants from the car. Plenty of youtube how to's and kits can be found easily through amazon or your local auto parts store. $20

    I don't think you need anything like a DA at this point. Others will have recommendations for you, and I encourage you to take their advice as well. Some great youtube channels are Ammo NYC, Larry is a master at explaining how to's. He has is own line of products but they're expensive. You can even email him with questions and he'll respond quickly and go above and beyond to explain somethingto you. Junkman, also another great channel. Chemical Guys, they have some pretty good products but their customer service is shit. Their youtube videos are pretty good but all they do is upsell their products.

    I'm fairly new to detailing like you. I dont have the best products, but what I use seems to work for me. There are better products out there but budgets can only be so large.
u/Jhadur · 11 pointsr/AutoDetailing

>Wash car using 2 bucket method, wash mitt. For soap I am using Meguiars Carnuba Wash

Yep, 2 bucket method and remember to use the right ratio of soap to water. I think that soap is 1oz --> 1 Gallon. I tend to use an old laundry cup and mark the different oz on that cup so that i know i have the right ratios.

>Scrub car with Nanoskin sponge, and a soapy mitt - or should I use ONR - what ratio.

Baggy test the paint but it most cases for a newbie there paint will need a clay/decon. IronX or TriX(Tar and Iron remover) is a nice thing to have but really is a luxury. In the case with what lubrication to use while you nanoskin, I like o just use my soapy water that is at the right ratio and should be clean due to the to bucket wash keeping junk out of the wash bucket. If your using ONR as clay lube the ratio 1:64.

>Rinse car with water

Yep using the flood method. The water should just sheet off and shouldn't leave much behind. https://www.youtube.com/watch?v=WAmb9DWdnFc

>Dry with ONR 1:16 ratio & Dry Me a River towell - is that a good ratio?

With ONR less is more in most cases. This will leave some behind. If i used ONR as a clay lube then the 1:64 is what i would be using. If i am mixing fresh i would be going 1:128. Reminder to pre-wet your towel wring it out.

>Wax - I was going to use Meguiar's G12718 NXT Generation Tech Wax 2.0 I am not sure about this one to be honest. My car is a daily driver, so I want something that will last a long time. Is there something else I should be using? Maybe the Meguiar's ultimate liquid wax instead? https://www.amazon.com/Meguiars-G18216-Ultimate-Liquid-Wax/dp/B004HCM9H4/

The biggest thing for protection staying is the prepwork. The step alot of people tend to forget is using IPA wipedown after everything as this will give the surface the cleanest, and driest area for the protection to bond to.


The Meguiar's NXT Tech Wax is also Meguiar's Sealant M21. This should get you 3-4 months depending on where the car is kept(inside vs outside 24/7)

The Meguiar's ultimate liquid wax they pushed more for a beading looking because care enthused like that. I think if you have the budget I would get Jescars Powerlock and Collinate 845 look for these on autogeek,autopia-carcare, fav detailing site as they will tend to have deals better than amazon

I would watch https://youtu.be/34GKKyrFrFI?list=PLG_BGdABDC9vWAZVwdmLNAU7J7kwNmJGH and kind of follow it but depending on the level of effort you want to put in.

If your looking to get just one protection product I would get Collinate 845


Any protection truly lasting longer then 6 months is either on a car that isn't exposed to the elements or is a coating. Protection should be reapplied at regular intervals. My daily driver is black, 3 kids and sits outside 24/7 so my interval is 3 months.


Hope this helps and enjoy your detailing path.

u/GetABucket · 2 pointsr/AutoDetailing

The answer to your first question of what makes vehicles "have that glorious-mirror almost appearance" is paint correction. There is no miracle product that will instantly turn shitty paint into 100% flawlessness in 1 application. It will take good claying, compounding, and polishing to get the results you are looking for. I'm sure that the clay, HF DA, M105 and M205, and the various pads you have will be able to get the results you are looking for. The only problem is time. It is going to take more time to get the results because the HF DA is not powerful, when compared to something like the Rupes or the Flex.

Carnauba waxes. The consensus is that they add depth and shine, but don't last long. Sealants last longer, but with less shine and depth. Both sealants and carnauba waxes will make shitty paint look less shitty, with carnauba slightly edging out sealants. But like previously stated, its all about the prep work. Sealant on flawless paint will still look better than carnauba wax over sealant on shitty paint.

Glazes. The sole purpose of glaze is to fill in scratches. No amount or type of glaze will replace correcting paint. It is unnecessary to put glaze immediately after a vehicle just had paint correction as there are no scratches for the glaze to fill in. However, sometimes it makes sense to glaze and not correct the paint. Generally, the two situations where glaze is better than correcting paint are when you don't have enough time to correct the vehicle, or the customer does not have the funds to correct the vehicle. Correcting paint takes hours and hours, while glaze (depending on vehicle size) may take up to an hour to apply and remove. Obviously, paint correction costs more than an application of glaze.

Spray on wax compared to Collinite #845 is like comparing pee wee football to the NFL. Even a shitty application of Collinite that is 4 months old will still be better than spray on wax. That said, I think it is still good to use spray wax after washing the vehicle.

One thing I didn't see you mention is wheels, tires, and trim. You also want to spend great care on these three areas because they create contrast with the paint, thus making the paint look even better. Essentially, you want all aspects of the wheel clean (face, spokes, barrel). You want the tire to be scrubbed with cleaner and then dressed with a water based dressing. You then want to clean the trim with all purpose cleaner and use either dressing or a trim restorer to give it the original look. Good wheel cleaner: Sonax Good APC for tires and trim:Meguair's D101 Good tire dressing: Adam's Super VRT

Anything I have said here is open for constructive discussion.

TL;DR Correcting paint is above everything. Glazes mostly unnecessary. Both sealants and carnauba waxes have their purposes. Look into cleaning and dressing wheels, tires, and trim.

u/zenautodetailing · 12 pointsr/AutoDetailing

2015 Ford Focus ST

I performed my Express Detail on this 2015 Ford Focus ST for a client. This client emailed me Thanksgiving morning hoping I could help with a gift his best friend "spilled" in his vehicle. I couldn't help him since I was on my way out of town, but I gave him instructions of how to help get the gift out. He ended up booking me to come over when I got back :)

His car is pretty new (a month + if I remember correctly), so my Express Detail was perfect for his vehicle.

This package is my most popular as I believe it's the most bang for your buck (or at least I tried to price it that way).

Products Used:

Wash

u/FightOrFlight · 3 pointsr/AutoDetailing

> Griots Garage Fiber Mit

Great kit.

> 2 or 3 buckets with Grit Guards

You can stick to 2 buckets to save money and just rinse it out after washing the wheels before starting your wash.

> Several Brushes for my wheels/Liners

I suggest getting the following brushes. Mothers wheel brush, Mother's wheel well brush, Tuf Shine tire brush. Then buy some wheel woolies if you want to clean your barrels without taking off the wheels.

>Soap

I suggest Chemical Guys, Meguiar's, or CarPro for your soap.

>I do a pre-soak with a hose powered foamer...do I need a special soap for this step?

A high foaming soap will be best for this. Most Chemical Guys soap works pretty well. I would suggest not getting a hose powered foam gun. Unless you're going off roading its not worth it. It's best to save up for a power washer and a foam lance.

> Plenty of microfiber towels

Make sure to buy some crappy towels for your dirty jobs like drying wheels, cleaning the undercarriage, and the carpets. I suggest zwipe microfiber towels for the cheap ones, and the rag companies eagle edgeless towels for your nice pair.

> Interior spray (I like the Meguiars Natural Finish, this okay?)

I have not had experience with that one yet. I have tried the Meguiars quik interior detailer before and it makes the plastics look stock. It doesn't do much cleaning, more of a finishing step. If you want to clean the interior I suggest getting Optimum Power Clean (diluted 1:10) or Chemical Guys NonSENSE (diluted 1:10).

> Waffle Towels (Oddles of them!)

Once your car is waxed you'll only need 2 large towels to dry your car. I really like the Chemical Guys waffle towels because they have good value for the money. Cobra towels are way better but way more expensive. I've heard the rag company has good ones too.

> See if I can get my hands on a leaf blower with a filter on it.

I bought a troy bilt leaf blower for $40 at home depot and it works pretty well.

I think you're forgetting 3 things.

  • Clay - the meguiar's clay kit you can buy over the counter is pretty good. Otherwise get a clay alternative like nanoskin autoscrub. If you get the alternative I suggest getting Optimum No Rinse and diluting it 1:8 for a lubricant.
  • Wax - I suggest getting a was with fillers in it so it hides some small scratches. Meguiars NXT liquid wax and Collinite #845 are both really good.
  • APC - an all purpose cleaner can be diluted to fulfill multiple purposes. Meguiars D101, Optimum Power Clean, and Chemical Guys NonSENSE are my favorite APC's at the moment. Each can be diluted to do different tasks. 1:10 for interior, 1:4 for NASTY interiors/carpets, 1:1 or undiluted for tires and trim.
u/Citecla · 2 pointsr/AutoDetailing

Hey guys i'm new to this detailing scene..but I do hope to learn a lot from everyone! I have an 05' white civic and the exterior isn't terrible, but there's definitely parts where there's medium oxidation and swirl marks. Just overall the paint doesn't feel glossy and smooth, just weathered and feels like metal.

Please let me know if I got the steps correct...any inputs is greatly appreciated!

  1. First do a thorough wash, and dry completely.
  2. Clay bar the entire exterior (I'm going to use http://www.amazon.com/gp/product/B0002U2V1Y/ref=ox_sc_act_title_3?ie=UTF8&psc=1&smid=ATVPDKIKX0DER)
  3. Here's where I don't know what I should do...do I compound or is that not necessary? I'm thinking if I skip compounding, I will use Scratch X (http://www.amazon.com/Meguiars-G10307-Scratch-X-2-0/dp/B0002UNON8)
  4. Then I will Polish with This: http://www.amazon.com/Meguiars-Ultimate-Polish-16-oz/dp/B004HCOE8Q
  5. What do you recommend I do next? Could I follow the Mother's 3-step Ultimate Wax starting with this product? http://www.amazon.com/MOTHERS-07100-California-Gold-Polish/dp/B0002U26QE

  • By the way, as you see I have attached the pictures...what do I do with the oxidation on the exterior windshield trim?
  • Next, this paint damage, I was thinking to get a touchup paint from the dealership, but how should I apply this?
  • Lastly, whats the most effective way to clean this part..the door jambs?

    Thanks so much for all your suggestions and inputs. I hope to learn a lot from all of you.

    PS. Extra question, I'm doing a roadtrip after the detail...(stupid i know) but what's a good product to get rid of the bug stains while I'm out on the road?

    THANKS!!
u/thisonewillsurelybef · 2 pointsr/AutoDetailing

Detailing products are usually not cheap. The best way to save money is to buy in bulk (gallon size), you'll save over time rather than having to go to autozone to buy more soaps, waxes, microfiber towels, wheel cleaners.

Will save you money for years. For instance Meguiar's glass cleaner (gallon concentrated). $20, dilute 10-1 with distilled water, you just bought yourself 10 years worth of glass cleaner. I'd say buying in gallon concentrated gives you a 5x better value over buying the parts-store consumer stuff. I know because ive already spent probably hundreds at autozone / parts stores on just car shampoos and glass cleaner just taking care of a Camry.

Meguiar's Shampoo Plus (amazon link)

Meguiar's Glass Cleaner (amazon)

Meguiar's Xpress Spray Wax (amazon)

Also the Last Touch detailer, wheel cleaners, interior cleaners, leather products. All good value.

etc. Compare the costs to parts-store grade products.



Kirkland microfiber towels (amazon) good for basic jobs that you don't want to use more expensive towels on.

Save all your spray bottles bottles of spray wax, interior cleaners, glass cleaner sprays, etc to recycle & reuse. Put the gallon-sized concentrated versions in them, re-label the bottle with a sharpie. You just saved $25 in bottles costs.

Invisible Glass Reach and Clean tool. This saves your back and neck muscles from becoming dislocated trying to reach into corners while cleaning glass. This tool is an essential in my book. I think its $15-20.

For DA polishing, look into the meguiar's DA microfiber system. You want the one with the 5" backing plate. Also buying in bulk principle also works here, you'll want a lot of buffing wheels so buy the 12-pack. amazon link

You'll want a clay bar kit. Meguiar's clay bar kit is a good value, I like that it comes with a case to store the clay.





u/daniellinphoto · 6 pointsr/AutoDetailing

Sorry this kinda became a small essay, I hope it's not too verbose but there's a lot of ground to cover if you're just starting out.

I got kinda shafted started out since I had a pretty damn oxidized, single-stage red Miata as well as a pretty-ok silver 2015 Subaru, so I kinda had to build two kits at a time since I didn't want to cross-contaminate my systems. I ended up getting a bunch of orange and white Lake Country CCS foam pads along with playing around with some Meguiars foam cutting pads for the Miata and the 5" Meguiars Microfiber Correction Kit for the Subaru and anything else that's clear coated.

I'm using the same Harbor Freight DA, but with the 5" backing plate that comes with the Meguiars kit. If you don't get the Meguiars kit, at the very least you need to order a new backing plate for Harbor Freight DA because the one that comes with it is well-known for being really shitty. I prefer using a 5" system as it fits a better into tighter spots and gives you noticeably more correction power over a 6" at very little perceived loss of coverage efficiency because of the smaller size.

Of note: I've only had poor experiences with microfiber pads on single-stage since they seem to clog up so fast, but they've been great on clear coat. Most people won't face this issue, but I figured I'd put it out there.

Pair whatever kit you build/get with the 36-pack of microfibers from Costco and you'll be in business in no time.

I did pick up a 6.5" Lake Country CCS red wax/sealant pad since I like to apply Collinite 845 to everything I care about. I intentionally picked an oversized pad for my backing plate because I'm only using my DA at the minimum speed possible (like 1.5 on the HF DA) to spread a thin layer of wax efficiently. If you crank up the speed by accident or out of curiosity, yes, the 6.5" pad does tend to get totally out of control in a hurry, so don't do that haha.

Don't forget your pad brush, or if you have an air compressor, you can use that to blow out your pads (Youtube it). Some method of cleaning pads is absolutely mandatory and for some reason, this is often overlooked or skipped by many people starting out.

Whatever you get, I like to have at least 2 cutting pads on hand and I'll make a conscious effort to switch halfway through the car, usually hood/driver's side for one and trunk/roof/passenger side for the other. I usually can get through a car with just one polishing pad but it's reassuring to have a backup on hand in case the pad explodes or I'm an idiot and set it down on the ground or something. I'm also kinda anal about cross-contamination of LSPs, so I now have a dedicated Lake Country red CCS pad for each LSP I use.

Finally, I know you're looking for advice on pads, but I ended up getting a bottle of the Meguiars DA Microfiber Polish since I prefer to lay down my own LSPs and the lifespan of the DA Finishing Wax was iffy, especially compared to the Powerlock+ and Collinite 845 combo that I use on cars I actually care about. The DA Finishing Wax is now reserved for my detailing side-hustle (which is currently helping fund putting a turbo in my Miata), since it saves quite a bit of time over separate polishing and waxing.

u/SPARTANsui · 3 pointsr/AutoDetailing

This is what I have. It works awesome. You will need a velcro backing plate and the pads to go with it.

So for example, my setup was the porter cable polisher, the Meguiar's 105 & 205 polishes, a 6in. velcro backing plate, orange pads used with the 105, and white pads used with the 205 polish.

I started with the orange pads and the 105 to "cut" the paint. Just to get all those deeps swirls out. This will leave micro swirls, which is why you have to follow up with the 205 and white pads. You could probably skip the 105 step all together and just use either the white pads or black pads. (that is if you don't have really bad swirls) I would probably try to black pads first as they would be the safest and less abrasive.

So here's how I would do it with your car if you just want to try and get minor swirls out. I would 2 bucket wash, dry, and then clay. I would then tape off all your trim (if you plan on doing the whole car) as getting polish stuck between trim or on trim is a PITA. I would just worry about trim that is close to paint. Prep work will take time, but you won't have to slow down when polishing each panel. So once your trim is taped off it's time to get to work. Decide which panel you want to start with. Apply 3-5 drops of 205 polish to the black pad, have some water (preferably distilled) in a spray bottle and mist the pad. Go over to the panel and stick the pad against the panel to spread out the polish. You should have a couple spots where there's 3-5 drops of polish on the panel now. Bring the polisher up to speed, (I usually do a middle speed) and start working the polish into the panel going back and forth in a sweeping motion. Once you have thoroughly gone over the panel, carefully turn off your polisher without lifting off. If you lift off you will get polish EVERYWHERE. Now wipe it dry with a soft microfiber towel. I purchased brand new microfiber towels (basically the softest ones too) from The Rag Company. You want to remove ALL polish residue from the panel as soon as possible. Do not move onto the next panel without doing this. This will also give you an opportunity to check your work. Use a bright light to see if you can spot anymore swirls. You shouldn't see any.

I am by no means a professional, I have only done this once on my own personal vehicle. I believe I got pretty good results. Take my advice with a grain of salt. I just watched Youtube videos to learn what I know. I hope this helps! Don't be too worried or nervous. It's pretty easy and was pretty fun. But I won't lie, because I went over my car twice, my arms were killing me by the end of the day. I could barely finish the last panel (it was on the side) because my arms just wanted to give out. It was hard work, but so so worth it!

It should also go without saying, but be sure to either do this in a garage or in complete spot. You want the paint to be cool and you don't want the polish to dry on the panel. Also you don't want to have any dust blow on your paint or settle. Basically you want your paint as clean as possible before you go to town with your polisher.

u/oc412 · 3 pointsr/AutoDetailing

This a a copy reply to a post from yesterday with pretty much the same question. This should help. YouTube the "Garry Dean Wash method" and do it that way.
___
Look into towels from The rag Company the [Eagle Edgeless] (https://www.amazon.com/RAG-COMPANY-Professional-Microfiber-Detailing/dp/B00GXRG64I/ref=sr_1_1?ie=UTF8&qid=1465578999&sr=8-1&keywords=rag+company) , [platinum pluffle] (https://www.amazon.com/RAG-COMPANY-Professional-Microfiber-Detailing/dp/B01691FHKQ/ref=pd_sim_263_1?ie=UTF8&dpID=51ZnYnkDerL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=T72HWKSGJSNY28KCRR5N) and the [creature edgless] (https://www.amazon.com/RAG-COMPANY-Professional-Dual-Pile-Microfiber/dp/B01CW21D9U/ref=pd_sim_263_23?ie=UTF8&dpID=61mdEodibyL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=4930TCHKYCSNPB5QDMAF) are my favorite. They are just better quality then CG towels and are perfect for using the "Garry Dean" wash method which is good for apartment dwellers.

EDIT: Also look into [WolfGang Uber] (https://www.amazon.com/Wolfgang-WG-3700-Uber-Rinse-less/dp/B017KSJ5ZK/ref=sr_1_1?s=automotive&ie=UTF8&qid=1465579171&sr=1-1&keywords=wolfgang+uber) rinseless wash. Its more costlier but WELL WORTH it to me. I just got a gallon of it from their website. I use it for my business on some customers vehicles and they notice when I do. Its by far my favorite rinseless out there that I have used. I have tried numerous different ones. [ONRWW] (https://www.amazon.com/dp/B00GG9FB8U/ref=sr_ph_1?ie=UTF8&qid=1465708329&sr=sr-1&keywords=optimum+no+rinse+wash+%26+wax) is good, don't get me wrong but I've had it streak and [ONR] (https://www.amazon.com/Optimum-NR2010Q-Rinse-Wash-Shine/dp/B00D8DR0AO/ref=sr_1_2?ie=UTF8&qid=1465708329&sr=8-2&keywords=optimum+no+rinse+wash+%26+wax) stains my wash media. I've never had a single issue with WG Uber and it smells like cherry candy. I feel like drinking the bottle every time I use it which makes it great to work with.

u/Santo_R · 2 pointsr/AutoDetailing

There was this one here, but it’s out of stock. Decent price too.

There’s also this. It’s an off brand (but I mean 90% of stuff comes from China anyway) and the brush bristles are soft.

This too. I don’t know how good microfiber is on wheels though. I personally have one similar to this that I bought in a kit from Costco, and use it for interior. But with a true brush style you can just rinse it out, vs microfiber that’s stains and needs to be washed.

There’s also this one. I’m pretty sure Canadian Tire has a smaller one to, but I can’t seem to see it on the site. Was in a store a few weeks ago and I think I saw one.


For something like wheels and tires, I don’t really see a point in spending crazy money on brushes. That may be an insult to people, but just as a hobby, I care that my rims are clean. For paint I use good towels and mitts (obviously to not scratch the paint) but for wheels, I’d rather save the money. I haven’t felt a good pro quality wheel brush vs a random one from Amazon or in-store, but even if I did, I don’t see how I’d justify the price difference (compared to something like a Eagle Edgeless 500 vs some random microfiber towel)

u/Trokeasaur · 2 pointsr/AutoDetailing

Meguiar's D101 is a really cost effective and solid product that can be diluted to interior and exterior concentrations.

Chemical Guys AllClean+ is another good option that can be diluted to interior and exterior concentrations, it also has a light almost fruity smell that I like. Some folks in /r/autodetailing have cooled a bit on Chemical Guys due to their ridiculous marketing and occasionally questionable customer service, but AllClean+ is a pretty solid product.


Ultima Interior Shampoo Gel is a nice, not dilutable product that smells amazing and does a great job on a lot of surfaces. It is less cost effective than the other 2 options but if you arent doing cars in bulk, its a good product.

u/YankeeATZ · 1 pointr/AutoDetailing

Been slowly building up 'maintenance' type supplies and think I'm on the right track but have a few questions. Here's what I've got:

  1. I have been considering getting some Meg's APC. Am I correct that I could use this on tires, light buildup on tailpipes, Husky (like Weatherbeater) all-weather floor mats? Any guidelines on dilution for these applications; and what else could the APC be used for?
  2. For interior cleaning, can I safely use the Meg's QID with the brushes to get inside crevices including around switchgear without risk of short-circuiting something?
  3. QID on a MF OK to clean nav/LCD screens?

    We had both of our cars detailed a couple months ago by someone who has a small side business in our neighborhood, so they are in pretty good shape, and just want to keep them that way. At some point in the future, I may consider getting a DA but for now just want to get better at regular maintenance.

    Thanks for reading this long-winded post!
u/gswoff · 2 pointsr/AutoDetailing


Here’s a straightforward shopping list and beginners guide. This will knock out most if not all of your swirl marks.

Shopping List:

Machine Polisher - PORTER-CABLE Variable Speed Polisher, 6-Inch (7424XP) https://www.amazon.com/dp/B002654I46/ref=cm_sw_r_cp_api_i_l7SADbKPP1Q6Q

Backing Pad - Astro 4607 5" PU Velcro Backing Pad https://www.amazon.com/dp/B003CH3Z8W/ref=cm_sw_r_cp_api_i_T7SADbZ187WK1

Buffing Pads - Chemical Guys HEX_3KIT_5 5.5" Buffing Pad Sampler Kit (4 Items), 16. Fluid_Ounces, 4 Pack https://www.amazon.com/dp/B01J588UNG/ref=cm_sw_r_cp_api_i_d9SADb8WF470V

Compound - Meguiar's G17220 Ultimate Compound, 20 oz https://www.amazon.com/dp/B06W5HCZ9M/ref=cm_sw_r_cp_api_i_M9SADb0ADEMZJ

Finishing Polish - Meguiar's M20532 Mirror Glaze Ultra Finishing Polish, 32 Fluid Ounces, 1 Pack https://www.amazon.com/dp/B001O7PNXC/ref=cm_sw_r_cp_api_i_i-SADbWXADMQT

Wax - Your preference


Here’s the guide:

1 – Tool Prep

Set aside the dual-action polisher, backing pad, and foam pads. Remove the included backing plate that’s already attached to the Porter Cable polisher, use the included wrench. Re-attached using the Astro pad, secure tightly.

2 – Wash

Wash your car by hand, preferably using the two-bucket method. Afterward, move the car into your garage or shaded area. You’ll want to be out of direct sunlight, keeping the paint as cool as possible.

3 – Clay Bar

Clay bar the entire car. Make sure to wipe down the finish afterward, keeping it as clean as possible.

4 – Compound Buffing

Grab your machine polisher, the Ultimate Compound, and the orange pad. Attach the pad to the polisher using the velcro backing, make sure it’s centered. Prime the pad by dabbing 8-10 dime-sized amounts across the surface. Start working one section at a time, around 2 x 2 feet. Before you turn on the polisher, press the pad against the paint. Compound polish should be soaked within the pad, along with the paint. Press the pad against the surface, set to speed setting 2-3, and begin spreading the compound around in quick passes. Then, turn it up to 5-6 and let the fun begin. Use overlapping, slow passes. Once you’re done, wide the area clean with a microfiber towel.

5 – Inspection

Check out your results of the first section. Go over the area again if most of the swirl marks aren’t gone. If the swirls are gone, but a light haze is present, don’t worry. The finishing polish will take care of it.

6 – Polish Buffing

Use the M205 Finishing Polish with the white pad. Follow the same steps from before. Prime the pad and rub it against the paint before turning on the polisher. Use a max speed of 3-4 with medium pressure. The Finishing Polish will take care of the rest of the haze and micro scratches. Once you’re finished with the first section, wipe clean.

7 – Inspection

Again, check out the results of the M205 Finishing Polish. It’s doubtful you’ll need more than one application, but double-check all the same. If it’s looking great, move on and finish the rest of your car.

8 – Wax

Your paint is looking great. The swirl marks are gone, leaving a bright clean finish. Apply the wax using the black foam pad. Use very light pressure, letting the pad float along with the paint. You’re just coating your car’s finish, that’s all. Wipe clean with a microfiber towel.

u/cf2121 · 5 pointsr/AutoDetailing

How To: Decontaminate your paint & wheels

  1. Gather your supplies. I have used a combination of a paint safe iron dissolving product, a clay bar, and a Nanoskin Sponge (picture 1)
  2. WARNING: If you are using an iron dissolving product, DO NOT have your car parked in the sun. Remember the flash point with chemicals? You do not want something strong enough to dissolve metal particles drying on your paint. Liberally spray the product on your paint, focus on the areas around the wheels as obviously kick up crap from the roads (picture 2).
  3. You should see a color change happening just as if you had sprayed the product on your wheels. Note: Because of the dark color of my car, I couldn’t get the camera to capture any color change efficiently. Dwell time shouldn’t really last longer than 5 minutes or so.
  4. Hose down the car. Yes, if you’re doing this step you’ll have to dry the car again. But you know how to do it now, so it shouldn’t be too bad!
  5. I like to clay bar the wheels next. I’m using an old piece of clay, and seeing as my wheels are pretty beat up already, I don’t really care. However, a new(er) piece of clay is always recommended. Examine the wheels. See any bits of tar or brake dust that didn’t come off from washing? (picture 4)
  6. Lube up the wheels using the product of your choice. For the wheels, I am using QD strength ONR. One the paint, I like to use the leftover soap from the wash bucket during the 2 bucket wash. Note: water is NOT an adequate lube for clay. Using back and forth motions, not circles, rub the clay on the wheels using medium pressure (picture 5).
  7. Examine to see if the problem area has been resolved (picture 6).
  8. Continue onto the rest of the wheels (picture 7).
  9. When clay becomes too dirty, fold and kneed it up until you can longer see the dirt accumulated (picture 8).
  10. When you can longer find a clean side, it is time to toss the clay (picture 9).
  11. If you drop clay, it’s time to toss it. This sucks, especially when you have just broken off a new piece to use. Clay picks up anything it touches, dropping it on the ground renders it useless (picture 10).
  12. NanoSkin products act the same way as clay. However, they require no refolding, last longer, and if you drop them you can just wash them off. The only real downside is that they tend to be a little more expensive, but are totally worth it in my experience. The sponge (which I am using) is the cheapest option. They also offer mitts, towels, and pads for a DA.
  13. Dunk the sponge in the wash bucket (picture 13).
  14. Using back and forth and up and down motions, ‘clay’ the paint (picture 14). Again, use medium pressure. No need to ‘grind’ the sponge into the paint. Note: when using soap as clay lube, I like to hose down the panel first again to give the soap extra lubrication. I know I know, you just hosed down the car and dried it again. It really isn’t so bad. It seems like a lot of steps backward, but trust me, you’re moving forward!
  15. Oh no! You dropped your sponge! (picture 15)
  16. No worries, hose it off and you’re good! (picture 16)
  17. I like to work in half panels at a time, and remember to start from the roof down. This way when you rinse off the car again, you’re working from the top down and not going back and forth.
  18. I will be tackling window decontamination in the Sealing ‘How to’.
    Note: When using a clay bar and/or sponge, you will feel the contaminants being picked up. When running over the paint or wheels, you’ll feel little bumps. Keep the clay/sponge motion going and the bumps should go away. It’ll start to feel smooth. To be 100% sure you’ve gotten everything up, place your hand in a plastic sandwich baggy and run your hand over the paint. Because of the ‘finer’ surface area of the bag, you’ll feel what you missed. https://www.youtube.com/watch?v=Ml434m7ILNA Here is a video of Mike Phillips explaining it.

    Congrats! Your car should be contaminant free and ready to be polished!


    Dodo Juice Ferrous Dueller

    The Mother's & Meguiar's Clay Bar Kits can be found over the counter for about $15-20.

    NanoSkin Fine Grade Sponge

    Optimum No Rinse

    CG Citrus Wash & Gloss
u/Zokuta · 1 pointr/AutoDetailing

> wheel cleaner plus would be an infrequent use, not every time. D143 would be your every-time use.

So, should I get both or just Meguiar's D143?

> griots fast correcting cream and a microfiber cutting pad from meguiars for the cutting portion of the polishing. replaces 105 and maybe the heaviest foam pad, but i'd just get a microfiber cutting pad in addition to the others.

Would you happen to have a link to both? I am a little confused on what those are.

> Meguiar's D120 glass cleaner concentrate instead of rainx glass cleaner. a gallon will last you the rest of your life. (dilute 1:10)

Seems like a lot, but I guess it is more worth it in the long run.

> a more neutral soap like Adam's or Optimum's. Gold Class has wax additives.

These are a little more expensive (unless I am looking at the wrong one). Is Optimum Car Wash CW2006G the correct one?

> as for concerns: do not use D143 on plastics. don't spray it on the wheel wells either. wheels only. yes you can use optibond on all plastics

Should I stick with Meguiar's D101 in for the plastics, wheel wells, and wheels?

> 303 Aerospace will protect your dashboard. Leatherique has a good conditioner but really you're not going to be able to stop creases from forming.

What would be a recommended cleaner for either/both? Should I use 303 Aerospace Protectant on with the leather conditioner as well? Should I get both the Leatherique Leather Rejuvenator/Prestine Clean or just the Leatherique Prestine Clean?

u/DasWerk · 3 pointsr/AutoDetailing

Buy three buckets, one for wheels, the others for a two bucket system.

Buy something to clean the wheels as well. I have the wheel woolies but I'm going to ask for the woolly wormit for my birthday from my wife.

Get a Waterless Wash and/or Quick Detailer for the times when you don't need a wash but you want to clean stuff up.

Take a look into this new Meguiar's Hybrid Ceramic Wax for a sealant. I have used the Fast Finish and it's great so this should be even better.

I also use Meguiar's Ultimate Quik Wax (D156 is the same but in a gallon jug) as a drying aid and it makes the car POP!


As a final suggestion, buy some 303 for the interior. You're going to love it. Not greasy, smells okay (not fruity), and leaves things looking great.

u/timbotx · 1 pointr/AutoDetailing

Hello,

I've read the wiki and its a huge resource. Thank you to all who put it together!

Some of the product reccommedations are unavailble on Amazon so I just wanted to ask a few questions with regards a brand new car I bought and see if these products are whats needed:

So firstly, washing the exterior of the car:

I have Meguiars Gold class wash, I have two buckets, and grit guards, I will do the two buckets method. Now do I dry the car with:

this: https://www.amazon.com/gp/product/B01ERU0F3A/ref=ox_sc_act_title_5?smid=A1RKELVBY446LD&psc=1 or

this: https://www.amazon.com/gp/product/B00GXRFLY4/ref=ox_sc_act_title_3?smid=A1RKELVBY446LD&psc=1

Once I have washed the outside and dried it with the towels, I then apply the wax, I will be using #845 - can I use these to apply it:

https://www.amazon.com/Viking-Car-Care-Microfiber-Applicator/dp/B0051MYL8E/ref=pd_bxgy_263_2?_encoding=UTF8&pd_rd_i=B0051MYL8E&pd_rd_r=BG4S92NE1D9CH9E2J67C&pd_rd_w=HVEIG&pd_rd_wg=6EheM&psc=1&refRID=BG4S92NE1D9CH9E2J67C

I know I needs to get a clay bar or a micro sponge I'm just not sure where/how this fits into the process, what items do I need to buy

These?

https://www.amazon.com/Mothers-07240-California-Gold-System/dp/B0002U2V1Y/ref=pd_bxgy_263_3?_encoding=UTF8&pd_rd_i=B0002U2V1Y&pd_rd_r=BG4S92NE1D9CH9E2J67C&pd_rd_w=HVEIG&pd_rd_wg=6EheM&psc=1&refRID=BG4S92NE1D9CH9E2J67C

https://www.amazon.com/gp/product/B00CUAWJ6G/ref=ox_sc_act_title_1?smid=ATVPDKIKX0DER&psc=1

Lastly, I am buying this window cleaner -

https://www.amazon.com/gp/product/B0006SH4KU/ref=ox_sc_act_title_8?smid=ATVPDKIKX0DER&psc=1

Is it safe to use inside and out? I would imagine spray directly on outside windows and just use some microfiber towels like this - https://www.amazon.com/gp/product/B00WC5KQGE/ref=ox_sc_act_title_4?smid=A1RKELVBY446LD&psc=1 to clean it off? On the inside I would imagine spraying directly onto the cloth would be better.

Do I clean the outside windows after the car has been cleaned and waxed?

I understand the basic process and with this being a new car I want to be 100% I'm doing the right thing, I fully intend on washing it every other week and taking great care of it!

Thanks

Tim

u/pbs094 · 1 pointr/AutoDetailing

Watch this for how to clean your seats.

For the rest of the interior like the dash, steering wheel and center console you want an All Purpose Cleaner and then a dressing/protectant to put on after. I like Optimum Power Clean and here's a review I recently did on it.

I use this as a dressing to protect afterwards. Note: most dressings including this one can leave behind a slippery/greasy residue so don't put it on your steering wheel.

The windows can be cleaned with glass cleaner then coated with rain-x or similar to make water bead off of it.

Here's a post I made on cleaning the engine on my Grandma's car. and here's mine after I did it. All you need to do is cover up any sensitive stuff that you don't want to get wet like the alternator or any exposed electrical connectors...I only did the alternator for mine. Then you rinse the entire engine bay lightly with a hose to knock off any loose dirt/grease/grime. Then you soak the whole thing with degreaser...I use this from Home Depot. Make sure you get it into all the small crevices where gunk builds up. Then agitate everything with a brush. I use this one and this one. Once you've scrubbed every inch of the engine bay and worked the degreaser into a foam it's time to rinse everything off with the hose again. The whole process takes only about 10 minutes. One important thing is to not let the degreaser dry on anything. shouldn't be a problem, but don't spray it on your engine then forget about it for a few hours. After a thorough rinse you can remove the bag from over the alternator and dry the engine. If you have a compressor then use it to blow dry all the water out of all the small places it collects in. If not then soak up as much as possible with an old towel then run your engine for a few minutes or drive around for a bit to dry out the rest of it. Then you can dress your engine with something like this or this.

Hope that helps and feel free to ask more questions!

All these products can be replaced with other similar products, these are just the ones that I personally use and like.

u/911x335 · 1 pointr/AutoDetailing

Look at all of the colors of pads out there. Blues, blacks, and Red are for finishing. Whites, oranges,and yellows are medium to high aggressive.

On my black paint I used an Orange, Green, Black, then red for waxing. I used CG V36 and V38. But used the V36 on my Orange pad only then V38 on the Green and Black pads. To bring me to a liquid wax/sealant on the red pad. Let it cure, then the next day applying Collinite as my last step.

I don't think you should focus on removing 100% of the swirls. But make it look 50-80% better. You don't want to wear down your paint. I highly recommend a test spot. My favorite is the top of the trunk. Tape off half of it. Do half through all of your steps. Review it with a few different lights, and sunlight to see your progress. Maybe take some photos of it. Once you get to the waxing with the polisher, it'll cover up the remaining swirls as the machine is amazing for waxing. Just don't machine wax a car if you haven't clayed or polished.

The biggest thing is to get the pattern of buffing down. And to be patient. For me, I could never do an entire car in one day. I'd do the hood and one half of the car, as best I could, then do the other half the next weekend or the next day.

Another thing, go on the Lexus Forums or even Autopia detailing and look at their detailing steps on the same car/paint. They may show the products they used and pads. But it's also not about the products but you can ask them questions if you need any quick tips. Overall, I think a few passes with 3 pads with a liquid wax will do wonders for your test spot. And if you proceed then tape off sections of the hood into 6ths and door panels into 4ths.

Amazon example: Hover over the Style for the pad and it will show you the color.. You can review the crap out of every product out there, but you just have to decide, then do it. I've used those exact pads and they worked awesome. Choose 2 polishes and 1 liquid wax along with 1 hand wax like Collinite or something else. Don't forget to clay bar your car before polishing and even though I don't always use a backing plate, it makes handling the DA polisher easier.

u/DarkLordKnoll · 1 pointr/AutoDetailing

Been looking to detail my car, and while I am still getting my stuff along with trying to find the time to do it.. I've started to come up with a couple of questions.

  1. Is it safe to use a magic eraser on the exterior / interior of my windshield + other glass on the car? Or would getting a drill adapter to polish the glass be a better option? Is there anything I can use to seal and protect the glass after cleaning it?

    The windshield has it's fair share of micro pitting and surface knicks (not cracks). And since a magic eraser acts as a very fine sandpaper I was thinking that it could possibly help to smooth out some of the pitting and knicks just to make these spots less noticeable when light hits it at certain angles.

    ​

  1. What is the best product / way to darken the pillars on my doors and seal them?

    Currently they are not that faded, but id like to keep them up before they get to that point.

    ​

  2. When I do detail the car I am planning to polish the car with Meguiar's M20508 Mirror Glaze Ultra Finishing Polish then use Meguiar's G18216 Ultimate Liquid Wax to protect it. What sort of pads or applicators do I need to apply this stuff?

    I have microfiber towels for cleaning and buffing but not sure what type of applicator pads to use.

    ​

    Also, any recommendations on a good / reliable, but repetitively inexpensive shopvac?
    Not looking for one with a bag or anything, just something for cleaning out the interior as those dam gas station vacuums are not worth 2$ for 4 minutes when you cant even get under the seats..

    ​

    Thank you for any and all feedback!
u/lanmansa · 1 pointr/AutoDetailing

A glaze would certainly cover up imperfections but it won't last too long. What country are you in? Can you do shipping through Amazon? If so I would recommend this, if price and shipping isn't too crazy. https://www.amazon.com/dp/B002654I46/ref=cm_sw_r_cp_awdb_y6buzb0CTB6TD

Then check out the chemical guys pads on Amazon as well. If you cant get good shipping via Amazon then I'm sorry, I wish I knew more to be of help! But good luck!

u/radroachbrz · 1 pointr/AutoDetailing

Hey you can try hand buffing it with Meguiar's ScratchX. http://www.amazon.com/Meguiars-G10307-ScratchX-2-0-oz/dp/B0002UNON8/ref=sr_1_1?ie=UTF8&qid=1404933405&sr=8-1&keywords=scratchX

It will take a lot of work, but you should be able to visibly improve it with a lot of elbow grease. Wash car, use clay bar, wash car again, scratch x the scratch, apply polish, apply wax. When using scratchX, work in a shaded area, work a 6 inch area of the car at a time, spread the product evenly and work it in circles for about a couple minutes. Repeat 5-10 times. Then cover with a wax protectant / sealant.

Products I recommend:

Meguiar's Scratch X, Meguiar's Soft Foam "4 applicator pads, Meguiar's Supreme shine microfiber, Gold Class wax.

This kit has everything you need, but I recommend picking up some extra foam applicator pads and supreme shine microfiber towels: http://www.amazon.com/Meguiars-G55032-Complete-Car-Care/dp/B0012ZEZ8A/ref=sr_1_7?ie=UTF8&qid=1404932960&sr=8-7&keywords=scratchX

u/MagneticGray · 1 pointr/AutoDetailing

If you like the Quik Detailer then check out their Synthetic X-Press Spray Wax. Another user on here gave me a tip to try using the X-Press in place of the QD so I'm just passing it on. Turned out to be the best last-step product I've ever used, hands down. I just spray it on and wipe off with a fresh microfiber after I dry my car and it leaves a nice wet looking mirror finish that beads water like a fresh wax. Meguiars says it renews your wax/sealant every time you use it so that makes sense. The final result is more solid and glassy (a lot like a paint sealant) instead of almost sticky or gooey like the QD can get sometimes.

A little goes a long way too. I filled up a 16oz spray bottle like 4 months ago it's probably still 3/4 full. At this rate the gallon container is going to last a few years.

u/JoeyOhhh · 3 pointsr/AutoDetailing

My parents' neighbor has been watching as I borrow Mom and Dad's hose and he recently asked if I could take on his car and I was happy to oblige! Overall, the exterior was in okay shape - couple bugs, a few spots of tree sap and bird poo, as well as just a good amount of dirt and mud tucked in some spaces. I gave the car a two bucket wash, clay, Iron X treatment, Iron X, clay and topped it off with a sealant. Thanks for pointing out that I listed my procedure out of order, /u/Deadfable! Here's the deets:

Products Used:

u/socialisthippie · 3 pointsr/AutoDetailing

You could probably get results that approach professional work like this using a couple machines in conjunction. Obviously pro's tools are going to get things that just won't come out otherwise... but time and determination tends to make up most of the gap.

>Steam cleaner: http://www.amazon.com/HomeRight-C800880-SteamMachine-Cleaning-Wallpaper/dp/B00A1B4B58/ref=sr_1_6?ie=UTF8&qid=1395695083&sr=8-6&keywords=Wagner+steamer

-- Plus --

>Carpet/Upholstery shampoo extractor vacuum: http://www.amazon.com/BISSELL-ProHeat-Compact-Multi-Purpose-14259/dp/B002KCMH6Q/ref=sr_1_1?ie=UTF8&qid=1395695238&sr=8-1&keywords=Bissel+little+green+machine

I'd probably start with the steam to help loosen the really gnarly spots/stains and move on to the extractor to pull all the gunk out.

Combine that with some good upholstery shampoo and some strong degreaser and some elbow grease with a semi-stiff brush and you could get anything out of your interior.

u/Chadman108 · 2 pointsr/AutoDetailing

Most of the clay out there is very similar, but there are different grades of clay (read: aggressiveness). Nanoskin is great for the "average Joe" who has a reasonably clean car but needs to decontaminate it, and clay is great for a 100% decontamination job like a very dirty or neglected car.

If you're new to claying... I'd suggest getting this kit, or something similar. It has everything you need as a beginner. I used these all the time when I first started detailing. I finally needed more so I bought in bulk and gallons of lube at a time.

The second thing I'd recommend is getting a small, fine nanoskin sponge. You can try it without dropping $45 for a mitt or pad and see if you like it and the results you get when working with it.

u/norn_necro · 2 pointsr/AutoDetailing

I drive a 15' BRZ and live in FL

https://www.amazon.com/303-30313-CSR-Protectant-Plastic-Fiberglass/dp/B00KN0UOEE/ref=sr_1_7?ie=UTF8&qid=1499474713&sr=8-7&keywords=interior+cleaner

I see 303 get a lot of good reviews on how nice their interiors look after applying. Is 303 a cleaner or just a UV protectant? Am I better off buying something like Chemical Guy's Interior Detailer and Protectant? or Meguiar's

https://www.amazon.com/Chemical-Guys-SPI-663-InnerClean-Protectant/dp/B008LPKV28/ref=sr_1_1?ie=UTF8&qid=1499476506&sr=8-1-spons&keywords=interior+detailer&psc=1

I keep my interior pretty clean. I do a quick dust wipe with a microfiber every few days so the dust doesn't build up. And every few weeks I'm looking to wipe it down and touch it up with an interior detailer and was wondering which one is preferred.

u/nehmia · 1 pointr/AutoDetailing

I'd get a fine grade nanoskin mitt or something similar for decon. Maybe a foam gun or foam lance and some soap. Might want to grab an APC for interior cleaning, although I think you can dilute ONR down as an APC... I really like Optimum APC though, very safe and effective.

I saw this today on slickdeals, choose subscribe & save to get it down to $13.35: 1-Gallon Chemical Guys Maxi-Suds II Super Suds Car Wash

u/damon_dolo · 7 pointsr/AutoDetailing

I was also a beginner at the beginning of the year. I went out and bought [Meguiars 105] (https://www.amazon.com/Meguiars-Mirror-Glaze-Ultra-Cut-Compound/dp/B003LMGDHI/ref=sr_1_1?ie=UTF8&qid=1496750162&sr=8-1&keywords=meguiars+105), and [Meguiars 205] (https://www.amazon.com/Meguiars-Mirror-Glaze-Finishing-Polish/dp/B003LMJP4Q/ref=pd_sim_263_1?_encoding=UTF8&pd_rd_i=B003LMJP4Q&pd_rd_r=YK6JBJ416NKY6325PPQG&pd_rd_w=WZ6u4&pd_rd_wg=LD9ed&psc=1&refRID=YK6JBJ416NKY6325PPQG), a [chicago electric DA from harbor freight] (https://www.harborfreight.com/6-in-57-Amp-Heavy-Duty-Dual-Action-Variable-Speed-Polisher-62862.html?ccdenc=eyJjb2RlIjoiODkwMjE0MTgiLCJza3UiOiI2Mjg2MiIsImlzIjoiNDkuOTkiLCJwcm9kdWN0X2lk%0D%0AIjoiMTE0NDYifQ%3D%3D%0D%0A), and ordered [orange and white hex logic pads from amazon] (https://www.amazon.com/Chemical-Guys-BUFX-102-HEX5-Hex-Logic-Medium-Heavy/dp/B0040MI9H0/ref=sr_1_1?s=automotive&ie=UTF8&qid=1496750285&sr=1-1&keywords=hex+logic+pads). This will be a good start. Get these things, should cost between 120 and 150 for all of it depending on where you buy, and that DA goes on sale quite often, looks like it's currently down to 49.99, so now would be the time to buy. I started off doing my Formula and then did my Sierra, and now have had a few other people come to me for correction and have a pretty good grasp on what I'm doing.

  1. Watch tutorials by Junkman2000 on youtube.
  2. Use the right size pads for your backing plate. The DA listed above comes with a 6" flimsy backing plate, and you should replace it with a 5" so it is smaller and easier to work with. Mark your backing plate as well, so if you push too hard, you'll see it stop spinning. Good for figuring out how much force you SHOULD be using.
  3. Take your time, and work at it slowly, you will have results.
u/Chocer24 · 9 pointsr/AutoDetailing

Avoid those cheap buffers and get yourself a Dual Action Polisher from a reputable brand. DA polishers are much safer on your car's clear coat and are user-friendly.

Griot's Garage 6" orbital polisher is a popular choice and will last forever.

Porter Cable makes a good polisher although it's not as powerful as Griot's and heavier.

MaxShine Shinemaster M8S is a great budget choice. I personally use this one and love it.

u/Tomimi · 2 pointsr/AutoDetailing

Get a Megs105 or Ultimate Polish (since its a beater I expect the paint is in need of compounding) $10

If you don't want to compound maybe a wax cleaner, its milder, cheaper and you could probably 1-step your car with it but don't put your expectations high because it only removes mild oxidation and some swirls. $7

If you need a backing plate, go get a 5 inch one $10, you need it

Get an CCS Orange Pad from lake (8-10)

Meguires Gold Class Wax on Target/walmart/amazon $10

I almost forgot but you need to clay before you start the magic and the cheapest one and most awarding one I know is this that's like $11.

Invest a few more dollars and if you want your money back you could always clean your friends car for a few bucks.

u/b0ltzmann138e-23 · 1 pointr/AutoDetailing

Newbie here

Someone please recommend an inexpensive and easy to apply sealer. Preferable one available on amazon.

Also - are there any instructional videos on using Nanoskin sponge?

EDIT:
My thoughts were to wash with 2 bucket method, clean up the paint using the nanoskin sponge and then seal it in to give it protection for the coming summer months.

Would any of these work as a sealer? Which one is the best in giving me long term protection? Easiest to apply?
Also - can I use these towels ? Or are they a bad idea?

Meguiar's M21 Mirror Glaze Synthetic Sealant 2.0

Meguiar's M20 Mirror Glaze Polymer Sealant

Meguiars G18216 Ultimate Liquid Wax

u/Stewbear5 · 2 pointsr/AutoDetailing

It's easy to get caught up in all of the information on the internet about detailing. My advice would be to keep it simple. The goal is to keep it clean and prevent swirl marks. Go check out AMMO NYC on YouTube and watch some of Larrys videos. 90% of detailing is a simple concept, prevent dirt or grit from being rubbed again your paint. Foam cannons, 2 bucket washes, air drying, etc. the purpose for all of this is to get as much dirt off without rubbing it into your paint. I bet most of the guys on this sub could achieve great results using the cheapest Walmart products because many have a good understanding of decontamination and technique. The reason we all cringe when we see automatic washes, brushes at self serve washes, squeegees on paint is because it goes again the basic principal of don't rub shit into your paint.

Once you get this principle down you can venture into the money pit that is auto detailing products to achieve even better results.

One thing I would add to your cart is Megs D156, it has a ton of uses and works great as a drying aid.

Meguiar's D15601 Synthetic X-Press Spray Wax - 1 Gallon https://www.amazon.com/dp/B005JPJMI2/ref=cm_sw_r_sms_c_api_2vROybTQWAZC2

u/Baconzjews11 · 7 pointsr/AutoDetailing

If you're trying to keep costs at a minimum then I recommend ditching that kit. Have you googled the Gary dean method of washing? If not then check it out. Basically he uses one bucket and a couple of microfibers as washing media. The pros to this is that 1. You don't have to lug around two buckets. 2. No need for grit guards. 3. After im done washing my car. Since the water is clean I can actually save it for later use. Gary deans method has one downside which is that you have to invest in more microfibers. Honestly, you can buy the ONR, and bucket. Then buy about 6-20 good quality microfiber towels. The clay you have is good and you're on the right track. You can also never go wrong with collinite 845. For the towels I recommend these

u/TheCamboRambo · 2 pointsr/AutoDetailing

Interesting, I'll have to give the Mother's QD and clay bar a shot then. This seems like it?.

Thanks! I love it so far, definitely want to keep it looking as good as I can.

u/ultragib · 2 pointsr/AutoDetailing

Are you talking about getting a DA polisher or just washing, cleaning, and sealing? If you're not getting a DA machine and polishing, you can get everything you need to detail your car for about $100 imo.

Get two $5 five gallons n buckets at Home Depot.

Here's a good car wash kit for $60:

TriNova Car Care Kit

If you want to decontaminate the paint ($15):

Mother's Clay Bar Kit

Here's a super-easy to apply sealant that should last 4-6 months, depending on weather and driving habits ($18 with coupon):

Meguiar's Ultimate Fast Finish

And get a bunch of good quality MF towels ($18 for 12):

12 Pack Microfiber Towels

That's plenty to get started and should be enough product to get you through 10 washes/details.

If you get addicted, be sure to check out The Rag Company for some great drying towels, and look into Optimum No Rinse wash to make maintenance washes a lot easier.

u/kocsenc · 1 pointr/AutoDetailing

So I decided to go for it and take better care of my car detail. Want to make sure I'm not crazy with some questions.

​

  1. Because of the efficiency of pressure washing, I've decided to make my routine cleaning a rinse, foam cannon, wash, rinse, dry. Is that good enough for routine wash?
  2. I have a Wolfgang paint sealant in my garage which I'll apply as a LSP when I'm confident enough, i haven't seen it recommended on the wiki, am I making a mistake with it?
  3. Is it ok to use microfiber towels instead of a mitt for washing?
  4. I've been watching this guys video where he claims using a high pH soap to strip everything and always re-sealing/re-waxing Meguiars spray wax is the way to go. He claims that over time debris gets melded _with_ the wax and so it's better to strip it all out. What are your thoughts?
u/tehlechkang · 9 pointsr/AutoDetailing

I really like it. I was going to pick up a bissell green machine but after watching reviews, it just looked too flimsy. Found this one without much reviews but decided to give it a chance. Things really solid and works great. Thought my floor mats were clean until i tried it out. http://imgur.com/a/nE4ZG

u/R3411yFFS · 2 pointsr/AutoDetailing

I have never used tuff stuff, but I have had good success with Meguairs APC

https://www.amazon.com/Meguiars-D10101-Detailer-Purpose-Cleaner/dp/B0006SH4GE/ref=sr_1_1?ie=UTF8&qid=1469057081&sr=8-1&keywords=d101

Another decent one is 303 multi surface cleaner/303 spot cleaner.

http://www.detailedimage.com/303-M2/Cleaner-Spot-Remover-P15/32-oz-S1/

The process is pretty much the same regardless of which cleaner, You spray it on, agitate it, then blot with a microfiber towel.

If that doesn't work you could try using a steam cleaner

u/redditmakesyoudumb · 2 pointsr/AutoDetailing

I'm fairly new, myself. I've driven clunkers most of my life. Spent about five years downtown where I didn't have a car. Now I'm back in suburbia, so I've got a brand new GTI, and it's the first one I've ever cared to take good care of. Here's what I started with:

u/hellfst · 2 pointsr/AutoDetailing

I never took a class, just watch a lot of videos. If you do decide to get a polisher, mare sure its a DA polisher. The one I use is proven to not burn the paint. At lease if you don't hold it down in one section for 20 minutes lol. It is the Porter Cable 7424 xp. I attach a 6 inch backing plate to it and use it with some of Meguiar's Polishing pads. Here is a link if you want to learn more: http://www.amazon.com/gp/product/B002654I46/ref=as_li_qf_sp_asin_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=B002654I46&linkCode=as2&tag=perfautodet0a-20
Now that I think about it, Chemical Guys also sell like a complete kit that looks like a reasonable price. Here is a link: http://www.amazon.com/gp/product/B003UW1IQU/ref=as_li_qf_sp_asin_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=B003UW1IQU&linkCode=as2&tag=perfautodet0a-20

I actually got mines from a local store and got rip off. This old lady sold it to me for 180 with pads only... bummer.
I think all you really need to do is clean the area well, clay it, mask it, and start with your polisher depending on the condition of the clear coat. edit: I can't spell lol

u/alwaysready · 4 pointsr/AutoDetailing

i think those scratches will come out. they dont seem so bad. you can confirm this by running your nail around them and seeing if it catches your fingernail. youll be better off if they dont really catch.

i think i would go with this car kit from meguiars

as well as ultimate compound

and some polish

i would then wash the car, clay the car, scratchx the scratches, plastx the headlights, compound the car, polish the car, then wax the car.

that will definitely do you. if you have more money, check out a bunch of the sidebar lists for more stuff. maximus's pretty much has it all.

edit: and maybe a couple of these mf applicators. i think they are easier to use and spread the product and work it in really well.

u/pulseOXE · 1 pointr/AutoDetailing

I agree with /u/Pinkman2012. Don't get the Eagle One stuff though. I've used it in the past, and at least for me, it was weirdly hard to remove. I REALLY like D156. That stuff is fantastic. Save some money and get the gallon. Once you use it once, you'll use it a LOT because of how great it is.

http://amzn.com/B005JPJMI2

u/DaytonDetailing · 2 pointsr/AutoDetailing

Okay so the first time you used Ultimate Compound and Ultimate Polish. That means you compounding, an aggressive cut. No matter how "gentle" you were, this is an aggressive paint correction. Depending on the paint, you could have taken little or a lot off(I was shocked to see how much the Cadillac STS I did this week was losing in paint depth after just a polish.). This is why I encourage you to invest in a depth gauge if you plan to do another round of paint correction. I'll be honest, you really shouldn't need to correct this quickly after the first round. You mention that there are swirl marks from previous owners still, so either your paint is hard or you didn't do much with your last round("gentle" I guess, but really with a machine nothing would be gentle IMO). Ultimately I am just telling you this because a gauge is like $125-$150 on Amazon and a repaint is more expensive than this, and if you plan on doing anymore paint correction it is a worthwhile purchase. This is just a cautionary thing, heed it or not.

​

A polish is typically going to be your final step unless you're working on some super finicky paint. In that case you may need a "jeweling" type polish that is super low cut, but this isn't exactly normal. My black Honda paint which is soft can be finished with m205 and a Yellow Rupes pad(m205 is typically a little more cut than polishes and the yellow pad is a standard polishing pad). Really shouldn't need to switch pads either unless again, finicky paint.

https://smile.amazon.com/CM8801FN-Coating-Thickness-0-1250um-0-50mil/dp/B00DKUUUP2/ref=sr_1_8?ie=UTF8&qid=1541731263&sr=8-8&keywords=paint+depth+gauge This is solid. $150<Repainting


You can get away without the gauge, but you're running a risk. Do what you will with that. Typically you should only really need one compounding correction then light polishing after that to maintain assuming you use safe washing methods.

u/ka14 · 1 pointr/AutoDetailing

That's probably the toughest part about detailing, is looking at the number of products and trying to find exactly what is perfect for you! That's the reason why detailing is so dangerous, once you get in, you keep searching and trying more products. If you want to keep up with maintenance, I'd suggest getting a nanoskin mitt. Lasts much longer, easier to use, less of a hassle, the pros go on forever, the only con is the upfront cost. If you want to clay once, clay is more economical but the mitt is DEFINITELY better in the long run. I do 2'x2' sections, and when you finish compounding, you wipe off. You don't want to mix products on the same pad. People say to buy 2-3 of each pad, as when one gets oversaturated it loses its effectiveness and may lead to micromarring, but I've never had a problem using only 1 Orange LCC pad and 1 White LCC pad for 105 and 205, respectively.

u/FagReducingTaskForce · 1 pointr/AutoDetailing

I had this issue and aside from a tool to get in the corners, you really are simply lacking in good microfibers. Once I bought some good ones for the first time in my life, I realized how crucial towels are in the whole equation of detailing. These are the ones I bought which are just great, in fact the best mf towels I own currently: http://www.amazon.com/dp/B00A8MZ7IA/ref=pe_385040_121528360_TE_dp_1

u/Pinkman2012 · 1 pointr/AutoDetailing

These orange pads are 7 dollars with prime. Is that too expensive? I use these occasionally for AIO and they've been ok. Lake country is better but not available the way you want to get them.

You want pads that match the aggressiveness of the product you are using to get the best finish possible using that product. That's just how it works. You can certainly use compounding pads for polish to up the aggressiveness(m205 comes to mind with this) but you still want polishing pads to finish without micromarring. I use a minimum of two per car, per color(except lsp, I have dedicated pads for each of my products that I use), switching at about the halfway point, maybe more if I use heavier polishes/compounds. Never work with a dirty pad, you're creating frustrations for yourself.

u/MainPFT · 2 pointsr/AutoDetailing

I've yet to use it. I have a bottle waiting to try but I've had a few ppl tell me about it. I actually used to use Meguiars D156 as a drying aide everytime I washed & it just didn't feel like it did anything. I'm sure it did, but I never got the feeling it was adding any protection or longevity to my wax job.

Maybe someone else will chime in but it seems like some ppl are using these ceramic sprays as their only form of wax/protection. So to me if that's the case then it should definitely be an added benefit to apply over top of Collinite.

Look up some vids on YouTube. There are plenty.

u/AWildAnonHasAppeared · 2 pointsr/AutoDetailing

Awesome! You definitely helped. One final question if it's ok. Will the following steps (in order) be good for a first time wash/detail?

  1. Wash the car with this soap.

  2. Scrub with these

  3. Dry off with this

  4. Decontaminate with [this]
    (https://www.amazon.com/gp/product/B00CUAWJ6G/ref=ox_sc_act_title_6?ie=UTF8&psc=1&smid=ATVPDKIKX0DER), while using this as the lube for it?
u/identifytarget · 7 pointsr/AutoDetailing

Okay. First off, I'm a newb so take my advice with a grain of salt.

Basic detailing goes like this

  1. Wash / Dry car
  2. Clay bar
  3. Polish [multi-step = (Cutting -> Polishing -> Finishing)]
  4. Wax (remove)

    You can google / youtube for detailed instructions on each step.

    I use a Porter Cable for application / removal

    For polishing, it can be a multiple levels of polish. Think of polish as a really fine sand paper in a liquid. Wipe immediately any that you get on plastic / rubber.

    They make different applicator pads and compound for different levels.

    They make buff pads for removing wax

    For black plastic /rubber you can use [Mother's Back to Black](http://www.amazon.com/MOTHERS-6112--Black-
    Plastic-Restorer/dp/B00GZLMEN4/ref=sr_1_2?ie=UTF8&qid=1417395899&sr=8-2&keywords=back+to+black)

    Buy a shitload of microfiber towels.

    You can get 99% of what you need at Autozone. Once you start getting professional, then maybe you need to go online to get the good stuff. I don't know.


    What you can do is experiment. Wash / Dry / Clay only the hood. Then use painter's tape and divide the hood into four sections. Experiment with the different levels of polish in each quadrant so you can see the different. Experiment with different application removal styles etc until you're happy with the results then repeat on the whole car.
u/niart906 · 1 pointr/AutoDetailing

I use my shop vac for spot cleaning in between my seasonal shampoo'ing of the whole interior. I like to use a foaming cleaner like Tuff Stuff because they're cheap and readily available OTC. Agitate with a good stiff bristle brush, and vacuum it up before all of the foam dissipates.

Just a tip, if you have the extra coin, I've been very happy with this handheld shampoo'er from Bissell. Well worth the money. http://www.amazon.com/BISSELL-ProHeat-Compact-Multi-Purpose-14259/dp/B002KCMH6Q/ref=sr_1_15?ie=UTF8&qid=1409155025&sr=8-15&keywords=carpet+shampoo+bissell

u/twinturbogarage · 1 pointr/AutoDetailing

Sure

This is the one I currently use: Chemical Guys MIC_493 Chenille Microfiber Premium Scratch-Free Wash Mitt https://www.amazon.com/dp/B003TTL0TE/ref=cm_sw_r_cp_apa_0tgFxb1M1HBR5
Literally the only CG product I own. I like that it's green so I can see the dirt. However here is one that is highly rated, but is blue, but if you don't mind that these ones seem good too, especially if you have a large vehicle. Plus you can dedicate one to the upper and lower half or however

Ultimate Car Wash Mitt - 2 pack Extra Large Size - Premium Chenille Microfiber Wash Mitt - Wash Glove - Lint Free - Scratch Free https://www.amazon.com/dp/B011B25IXY/ref=cm_sw_r_cp_apa_0vgFxbQ8H8HA9

u/LtPatterson · 1 pointr/AutoDetailing

Looking for some paint thickness gauge / meter recommendations on the cheap. For personal use. Not interested in spending thousands on a professional gauge.

https://www.amazon.com/dp/B07D337RPW/?coliid=I1B4EN3ZFPAIRQ&colid=3GJZC1EZZLFLA&psc=0&ref_=lv_ov_lig_dp_it

Seems too good to be true, but is it worth trying out?

Otherwise, I might end up with this one, seems like it has good reviews.

https://www.amazon.com/dp/B00DKUUUP2/?coliid=I39I2VK46CLC8P&colid=3GJZC1EZZLFLA&psc=0&ref_=lv_ov_lig_dp_it

u/orlheadlights · 2 pointsr/AutoDetailing

I would pick up the following, if you are ready for machine polishing, you will need to pick up a DA polisher and pads as well.

u/Gad001 · 1 pointr/AutoDetailing

Definitely give Sonax Full Effect Wheel Cleaner a try. I have had amazing success with this stuff. It will turn from green to red as it is working and breaking down iron particles and break dust.


Also, you can give either CarPro's Iron-X or TRIX (Tar and Iron Remover) a try.

Honestly, by looking at the picture, the Sonax should clean up the break dust and those streaks. Just let it sit on the wheel for a couple minutes and agitate it with a brush. I use this brush to get in behind the spokes as well.

As far as keeping brake dust from accumulating as quick, I'm not sure if there's really a remedy. You can wax your rims, there is stuff out there specifically made for rims, but I've never used it, so I'll let someone with experience speak on that. However, I read the other day someone used Collinite #845 Insulator Wax on their rims (same wax I use). I may give this a try next time I wash the car and see if it helps control the brake dust.

u/r4x · 1 pointr/AutoDetailing

I actually LOVE the chemical guys gold MF towel

https://www.amazon.com/Chemical-Guys-MIC_506_12-Professional-Microfiber/dp/B00A8MZ7IA/ref=mp_s_a_1_3?keywords=chemical+guys+microfiber&qid=1557973969&s=gateway&sprefix=chemical+guys&sr=8-3

I've used many different types of towels and these just suit me the best. They're cheap enough ( I got a pack of 12 for $16 so I bought as many as I could afford.)

They last a long time with proper care but ate cheap enough that I'm not afraid to toss them when necessary. Enjoy!

u/Kubi74 · 1 pointr/AutoDetailing

Opinion: I think this at 1/4 of the price will do almost an identical job to the ammo http://www.amazon.com/S100-13700W-Carnauba-Paste-Wax/dp/B000GZQP08/

These carnauba waxes will not last long... especially in heat.

-

Instead of the gold, go with the ultimate like the other dude said, AMAZING wax for the price:

http://www.amazon.com/gp/product/B004HCM9H4/

This stuff will last a long time. great beading.

u/bmcclure937 · 1 pointr/AutoDetailing

Can you please link me to the MIC_506_12 you are looking at?

I found this 12 pack on Amazon... does not look like 46% off for me though. Still a pretty solid deal.

I am also curious, what would be a good use for these different microfiber:

  1. Zwipes (cheaper and thinner)
  2. Chemical Guys MIC_506_12
  3. Chemical Guys MIC_1024_3

u/PhillyLyft · 4 pointsr/AutoDetailing

It's my car! Wow, she looks wonderful. In this case I am working with a "work contest" where I get to pick $50 worth of items, so I'll probably pick out some chems and cleaners. The Meguiars Clay Bar kit is in the recommended tab, for an example. Our I might just tell them to order me this.

u/nakedjay · 5 pointsr/AutoDetailing

Go to Amazon and order this (I like Meg's products),

u/LocalAmazonBot · 1 pointr/AutoDetailing

Here are some links for the product in the above comment for different countries:

Amazon Smile Link: http://smile.amazon.com/gp/product/B0000AY69N/ref=oh_details_o01_s00_i00


|Country|Link|Charity Links|
|:-----------|:------------|:------------|
|USA|smile.amazon.com|EFF|
|UK|www.amazon.co.uk|Macmillan|
|Spain|www.amazon.es||
|France|www.amazon.fr||
|Germany|www.amazon.de||
|Japan|www.amazon.co.jp||
|Canada|www.amazon.ca||
|Italy|www.amazon.it||




To help donate money to charity, please have a look at this thread.

This bot is currently in testing so let me know what you think by voting (or commenting). The thread for feature requests can be found here.

u/pachewychomp · 7 pointsr/AutoDetailing

Great job! Hope you used something other than Armor All otherwise he’s going to have a nice haze on the inside of his windshield.

Aerospace 303 is a really great product that is similar to armor all but doesn’t leave the super greasy feel or oily haze.

303 (30313-CSR) UV Protectant Spray for Vinyl, Plastic, Rubber, Fiberglass, Leather & More – Dust and Dirt Repellant - Non-Toxic, Matte Finish, 32 Fl. oz.

https://www.amazon.com/dp/B00KN0UOEE

u/jb007gd · 1 pointr/AutoDetailing

I use these when applying the M105:
Chemical Guys BUFX_102_HEX5 Hex-Logic Medium-Heavy Cutting Pad, Orange (5.5 Inch) https://www.amazon.com/dp/B0040MI9H0/ref=cm_sw_r_cp_apap_JnEUTcXh1t2xd


Then I switch to these to apply the M205:
Chemical Guys BUFX_104_HEX5 Hex-Logic Light-Medium Polishing Pad, White (5.5 Inch) https://www.amazon.com/dp/B0041MVQ4M/ref=cm_sw_r_cp_apap_3CuEdXSpOPLHj

To be honest, I can't tell much of a difference before and after using the M205. I can definitely see improvement after using the M105 but yeah, last week I did my front driver's side fender and it took me five hours. Sad face.
Sometimes I think I should have bought a flex as I understand they work faster. I went with the PC because I understood it to be extremely safe. Being my first time and all, I wanted to be safe rather than burn my paint. But yeah, five hours/panel is ridiculous.

u/SouthernAutoSpa · 2 pointsr/AutoDetailing

Depends on your budget. I use CarPro Reset shampoo as it cleans extremely well. However, you can also use Meguiars Gold Class and it does quite well. For wax, I would stay away from paste waxes. Find a good liquid wax as it spreads thinner which makes removal easier. Alternatively, if you want the same protection, if you do order from CarPro, pick up their Hydr02 Lite, which is a spray sealant that lasts just as long as wax. Just spray it on while wet, and rinse with high pressure. Protection for 3-4 months. Links below:

Reset - https://www.carpro-us.com/wash/carpro-reset-car-wash-500ml-17oz/

Hydr02 - https://www.carpro-us.com/coatings-sealants-spray-wax/carpro-hydro2-lite-1-liter/

Meguiars Gold Class - https://www.amazon.com/Meguiars-G7164-Class-Shampoo-Conditioner/dp/B0009IQXFO/ref=sr_1_5?ie=UTF8&qid=1549208569&sr=8-5&keywords=meguiars+gold+class+car+wash

You can get CarPro from Amazon but its more expensive. Hope this helps!

u/JuvenileSenseOfHumor · 3 pointsr/AutoDetailing

In my opinion, if this is your first polisher and you're not a seasoned professional, I would not recommend it.

  1. it's a rotary (not a dual action) sander/grinder/polisher. Dual action is a lot more forgiving and a lot more user friendly.

  2. it's 7 inches - that is massive for a first polisher. Most people recommend a 5-6 inch polisher.

  3. simoniz doesn't make the most quality products. Their price points are amazing, but the quality of the product usually reflects why their price is where it is.

  4. 10' cord is good if you want to strangle yourself. Using extension cables when working with a polisher is annoying as it can come unplugged by you pulling on the cord or inadvertently stepping on it moving from point to point.

    Look for the Griots Garage 6in dual action polisher or the Porter Cable 7424xp 6in dual action. Both can be had for nearly as cheap. I kept the GG polisher in my Amazon waitlist because it goes on sale from time to time for $155'ish which is a steal.

    Griot's Garage 10813LNGCRD 6-Inch Random Orbital Polisher with 25-Feet Cord https://www.amazon.ca/dp/B009UKUURO/ref=cm_sw_r_cp_apa_DKqxzbQJ5NVFQ

    PORTER-CABLE 7424XP 6-Inch Variable-Speed Polisher https://www.amazon.ca/dp/B002654I46/ref=cm_sw_r_cp_apa_6Jqxzb3VNSE56

    Also, check out the wikilinks in the sidebar for recommended products - http://www.reddit.com/r/AutoDetailing/wiki/index
u/iamtehstig · 3 pointsr/AutoDetailing

This is the one I went with:
http://www.amazon.com/dp/B003CH3Z8W/ref=cm_sw_r_udp_awd_EFqiub0TTBDWG

I have had it on for a year and it is holding up great. The velcro is very strong and it holds well.

u/GrammarFailure · 2 pointsr/AutoDetailing

Do you want to buy a mildly good one and have it forever or rent an amazing one and have it for a weekend? Rugdoctors can be had at a lot of stores for rentals and will do a great job of any carpet/upholstery. Up to you.

The Bissel Little Green is generally the one people go for. You want a heating element to your extractor or it won't open the pores in the carpet and will do a worse job.

u/redsox985 · 1 pointr/AutoDetailing

This is the Megs kit I was talking about. I figured the cheap towels would be good for dirty jobs like wheels and exhaust. I'll take a look at the Griots offering. I'm thinking I'll be going with hand polishing for now. I want to get a good base before I maybe dive in over my head. Which towels would you recommend over the CG ones?

u/NVdustytrail · 1 pointr/AutoDetailing

What do you mean by air blower/sheeting? I have tried an air compressor and the pressure is just too high and breaks up the beads of water bit doesn't really blow them off. But yeah I need to get the buckets and grit guards and the sheepskin wash mitt. I have been using a microfiber sponge thing kind of like this. What kind of cloth do you recommend for applying wax and what brand wax? I have been using some wax that came with the vehicle but I'm just about out and I've been applying it with some microfiber wax applicator towels from O'Reill. Also how often should I wash the wax applicators and how?

I was just at Walmart and picket up some of this, not sure if it's recommended or not. I also got one of these but I'm not really sure of the purpose of it, I just keep hearing people talking about using "clay bar"¿?.

Sorry for the wall of questions, but like I said I'm really new to this and would greatly appreciate of you could answer most of them (if not all)

u/lithiumbb · 6 pointsr/AutoDetailing

Well the first, and biggest, difference is power. The one you linked is 1.1amp, the griots is 7 amp and has adjustable speed, so it can work faster than the buffer you linked. The type of pads they use is different as well, the griots has a velcro backing plate so you can use pads like these. 10 inches also is quite big and probably nearly impossible to use on tighter areas.
(I'm not an expert so please feel free to correct me on anything)

u/ArtistSchmartist · 1 pointr/AutoDetailing

You can try either bug and tar remover by turtle wax (the only product ID ever buy from them), 90% isopropyl alcohol will work too, as it works great for tree sap and it's safe for clear coats, or if all else fails, you can try a clay bar with some quick detailer as lube. Mothers has a quick detailer and clay bar kit you can buy at any auto parts store like AutoZone/Advanced Auto.

u/Nagare · 1 pointr/AutoDetailing

Because of the Prime Day deals I decided to pick up a few different products without knowing too much. I bought: Optimum No Rinse, Mothers Clay Bar System, Microfiber Clothes, Liquid Wax Paint Sealant, and Hybrid Wax.

My quick understanding is that the recommended process is: wash > clay > wash > wax. In terms of these products, does that mean:

ONR wash > Mothers Clay (should I use their lube or just the ONR water?) > ONR wash > Liquid Wax > Hybrid Wax

Just want to make sure I follow the right order so I can start to keep my car in good shape. How often should I clay? What about the sealant and the wax?

Thanks!

u/NsRhea · 1 pointr/AutoDetailing

Hello!

So I've been lurking here for several weeks trying to soak up what I can. I've checked out the wiki page on starter kits and I guess I'm just wondering a couple things based on the list to get myself going.

Gonna get the buckets and the grit guards. I've got a ton of microfibers I use for my car already.

I was thinking of getting the Griot's DA polisher recommended (here)[https://www.amazon.com/Griots-Garage-10813STDCRD-Orbital-Polisher/dp/B009UKUUWE/ref=as_li_ss_tl?s=automotive&ie=UTF8&qid=1462198536&sr=1-1&keywords=griots+da+polisher&linkCode=ll1&linkId=3a68733089f6c8d0f136c31b5c3bb8d1]

I guess I'm wondering what chemicals I should be using on my vehicle?

I do live in an apartment complex though so I DO NOT have access to a hose because our landlord has got it under lock and key. I read a few days ago about a product that someone used outside and it was still ok (though I do have access to a garage!).

I guess I'm just more lost as to where to start besides the DA polisher.

edit: Oh! I've used a clay bar before and while it was nice, I was wondering about this nanoskin sponge that's also recommended.

https://www.amazon.com/Nanoskin-AS-019-AutoScrub-Grade-Sponge/dp/B00CUAWJ6G/ref=as_li_ss_tl?s=automotive&ie=UTF8&qid=1462198361&sr=1-1&keywords=nanoskin&linkCode=ll1&linkId=4c532041fcdbfa6b35f768083c70423e

Is that like a 1:1 sub for clay bars? Same thing just not wasted if dropped?

u/YuhDunBenShrunk · 1 pointr/AutoDetailing

Hey all!
I recently bought a Meguiar's kit along with some of their microfibers and a "Water Magnet" in order to do my very first detail. My car is a white 2000 Subaru Outback and I was looking around stores and saw that Meguiar's offers a wax specific to white vehicles. I was wondering, is this just a marketing ploy or will it actually improve the end look of my car over the "Gold Class Carnauba Plus" included in my little kit. Thanks in advance for any help!

Link to kit purchased:

http://www.amazon.com/gp/product/B0012ZEZ8A/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

Link to White Wax I'm referring to:

http://www.amazon.com/Meguiars-G6107-White-Wax-Paste/dp/B009OBW23O/ref=sr_1_1?s=automotive&ie=UTF8&qid=1425505116&sr=1-1&keywords=meguiars+white+wax

u/taco_bellis · 2 pointsr/AutoDetailing

Yeah it was really only a couple charts, didn't give much detail. I found this Meguiar's Start Kit on Amazon for $50. Seems like it has pretty much everything. I was just gonna get another set of microfiber cloths to go with it, and maybe a separate wash mitt for the wheels. What do you think?

u/tsreimer · 2 pointsr/AutoDetailing

[Nanoskin Mitt] (http://www.amazon.com/Nanoskin-AS-016-AutoScrub-Fine-Grade/dp/B00DOS0LH2/ref=sr_1_3?ie=UTF8&qid=1422296825&sr=8-3&keywords=nanoskin)

There is also a medium grade sponge that is smaller but works really well, as well as a combo pack that has medium and fine grade together.

Note that you shouldn't use this as a standard 'wash mitt' though. It is literally a substitute for a clay bar.

u/WaterishCube · 3 pointsr/AutoDetailing

I totally get what you mean. For bird poop removal I use ONR diluted to 2oz to a gallon in a spray bottle. Or just do a regular wash and when the mf towel touches the poop I put it in the dirty towel bucket and grab a new one.

For claying I use ONR diluted the same as before and what ever clay I have on hand most of the time it is the meguiars you can buy at the auto store.

For regular soap I use Adam's car shampoo (the blue one) I love this stuff in a bucket or foamer it works amazing for both.

Interior I mostly use onr in what ever dilution I have the most of at that time.

For cleaning glass I use the method Larry for AmmoNYC uses. Invisible glass works wonders for me but if it does not work for you don't be afraid to try other products. fine tuning your process will be trial and error of new products.

If you don't have a bottle of ONR already I would pick one up I use it every time I detail vehicle. You can find it on amazon here
https://www.amazon.com/Optimum-NR2010Q-Rinse-Wash-Shine/dp/B00D8DR0AO/ref=mp_s_a_1_1?keywords=onr&qid=1569990842&sr=8-1

But the biggest tip I can give anyone that is starting out is to drink water during detailing.

Hope this helps.

u/JohnBaggata · 1 pointr/AutoDetailing

How do I get the paint on the right side of this picture looking like the left?

https://imgur.com/tL3kCaW

I bought the car used, neglected and abused. I've patched up the mechanical bits and I want to get my paint looking nicer, and hopefully uniform. My issue is that on certain parts of the vehicle the paint doesn't have much depth to it, but if I look on the inside of the doors, the paint is a deep beautiful color.

Would this be a good kit for it?

Mother's Clay Bar + Meguiar's Compound, Polish, and Wax

u/Checkers10160 · 2 pointsr/AutoDetailing

Interesting, so I guess I will save the bays for actual dirt and grime then.

So I will need a bucket, some ONR wash (Is this diluted with water?), a drying aid, and a drying towel. What exactly is a drying aid, is that like a product?

Will these works?

ONR

NO.1 Wash mitts

NO.1 Drying Towels

Also, you said you do a quick 10 minute wipe down, is that the process you use? Or do you have another touch up product or something?

Thank you by the way!

u/Warmachine- · 2 pointsr/AutoDetailing

Nice ride. I myself have a 2015 Mazda 3 GT. I use Lexol for cleaning and conditiong (protecting) leather. Just use some TRC microfiber towels to clean the leather and the rest of the interior. For the dash, I just use Meguiar's Quik Interior Detailer and D101 APC. It doesn't leave a shiny residue on the dash. I use those two for almost everything on the interior.

u/mckeefner · 1 pointr/AutoDetailing

It is an 05. Paint is in decent condition but a lot of contamination. It was sitting under a sap tree for 2 years. I spent about an hour claying the hood and it removed maybe 70% but there was a lot of stuff. I was using chemical guys clay.

Thank you..glad you said something :)

Like this

u/procrastislacker · 1 pointr/AutoDetailing

I believe clay bar qualities are different. Just like with most stuff, generally the higher the quality, the more expensive it is. The cheaper ones I've worked with have streaked heavily and more often. Depending on the vehicles condition, and how often you detail, a clay bar can last a long time. This CLAYBAR is pretty cheap & plenty of people like it. For a clay sponge it does the job.

u/DJdannyK · 1 pointr/AutoDetailing

I used Meguiars Ultimate Liquid Wax http://www.amazon.com/Meguiars-G18216-Ultimate-Liquid-Wax/dp/B004HCM9H4. And thanks for the positive thoughts!

u/smoochara · 2 pointsr/AutoDetailing

Noob detailer. Please help to check my rinseless wash process for mistakes and/or advise on existing paint damage.

Started following this sub when I got a nice enough car to care for. It's a Mazda with soul red paint though and seems like every little thing is super visible and the clear coat scuffs when you look at it wrong. I street park in Brooklyn, dust, leaves, pollen, bird bombs and all, every day. Was recommended to adopt ONR rinseless 2 bucket method, researched and tried to follow to the best of my ability.

First, the list of equipment I obtained thus far:

  • 2x buckets + grit guards
  • ONR concentrate (1 Gal. bottle)
  • Big Red Sponge
  • Mother's 07240 Calif. gold clay bar + instant detailer bottle kit
  • Opti-Seal (20239) 8oz. bottle with applicator sponge
  • Costco MF towels
  • Aliexpress stuff: few MF sponges, couple of high gsm/edgeless mf towels to try out.

    Below is the workflow I had going today, so much new stuff to use and new methods, I did not feel in the least bit confident that I did it right. Asking for folks here to review it and point out any mistakes I have made along the way as well as tips to optimize the process for the future:

    I went out to the car with two buckets, each with grit guards, one with 256:1 ONR solution, the other just warm water for rinsing. I started applying ONR solution in straight line motions with BRS one panel at a time starting with the roof>rear window/trunk gate>windshield>hood>front fenders>rear fenders>rear doors>front doors. I do not aim to detail interior or wheels much tbh, but i did dedicate about 6 costco towels to wheel duty by cleaning up the nooks and crannies of the wheels and wheel wells, rinsing them in rinse bucket and never dipping them back into the ONR bucket after first use. Following that, I cleaned and refilled rinse bucket and went back to repeat the panels. Why? Well, the car was very dirty with BRS quickly becoming black with dirt and me switching to costco MF towels to make another two passes over each panel, discarding towels that get visibly dirty on all quarters into laundry pile. I tried folding dirty halves/quarters away and using the Ammo NYC sweep and rotate style to minimize contaminants dragging across paint. Eventually, I felt ready to move onto claying because costco towels and BRS were no longer looking dirty as I passed them across.

    Here is where my confidence and excitement of a new auto detailing convert took a big hit. First of all, I had a superficial but long scratch across the right side which I expected to be possible to mask down with claying>using opti seal, since I could not actually feel it with my fingers. That didn't work at all, although I could tell by doing the ziploc bag drag test that the clayed areas were much smoother than the untreated ones. I used Mother's detailer spray bottle to lubricate, half panel at a time, then slide the pancake shaped clay sideways with no inward pressure until i stopped feeling drag resistance. I added lubricant if I felt clay stop on dry areas.

    I wanted to change pace after failing with masking the scratch, so I started on the inside of the windshield. I made a 10:1 ONR solution in a spray bottle, sprayed it direct onto a high gsm fluffy mf towel from aliexpress and started wiping away at the inside. I then used the flat looking towel (also from aliexpress) to wipe down streaking. I was pretty happy with the results, but unsure if I did something wrong or missed a step. Still, I moved on.

    I then wiped the entire exterior with a clean towel and soaked up the Opti seal applicator, proceeding to apply the stuff one panel at a time and following up with another clean mf towel to wipe off the excess wherever i saw streaking (which was almost everywhere as it was my first time and I wanted to lay a generous protective coating). I got rid of streaking easily, but....

    The result was clean, silky smooth paint, but upon closer inspection, it was covered in etchings from leaves, bird bombs and whatnot. The ONR>instant detailer>clay>opti-seal did not remove it. I did not apply pressure onto paint in affected areas during any of the above procedures, as I was afraid of damaging clear coat even further. Did I need to apply more inward force and scrub down the etched areas once it was cleaned from contaminants? Or the only solution to these spots now is to polish? Here is a picture of one of many etchings. some others are bigger in size, some area smaller, one is shaped like an outline of a small leaf -( . The hood also has some tiny black dots that seem to have a white halo of discolored paint around them ~1mm wide.

  • scratch close up (https://i.imgur.com/glgivGd.jpg?1) (taken with 1:1 macro lens, so looks rather thick, it really isn't)
  • Bird bomb #1 (https://i.imgur.com/wlK9j7J.jpg?1)
  • Bird bomb #2 (https://i.imgur.com/FsUQBm4.jpg)
  • Bird bomb #3 (https://i.imgur.com/vE5j9IM.jpg?1)
  • Leaf etching (https://i.imgur.com/wIm1I2v.jpg?1)
  • black dot with white 'halo' discoloration (https://i.imgur.com/oj9Tili.jpg?1)

    What would be recommendations for me at this point, and what ballpark cost to fix if I am not skilled/dedicated enough to get into polishing myself if that's the route I have to take? I did look over the field guide link for paint damage in the sub wiki section, says etching removal can require up to polishing depending on severity, but I couldn't tell what severity etching I got going tbh.

    Finally, are there any parts of this process that were done wrong or could be done better? Are the instant detailer spray and 10:1 ONR spray different in what they can do, or do they more or less perform same function to lubricate and suspend contaminants on the clear coat? Do I need to somehow strip opti-seal layer every few months to re-clay and re-seal, or just ONR on top and instant detailer spray>spot clay>reapply opti-seal in trouble spots from here on out?
u/_revy_ · 1 pointr/AutoDetailing

So my first ever detail is planned out like is this

  1. Foam Cannon wash + rinse
  2. ONR Rinseless wash + dry
  3. ONR Lube + Nanoskin AutoScrub Fine Grade Sponge (https://www.amazon.com/gp/product/B00CUAWJ6G/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1)
  4. Meguiars ScratchX 2.0 Polish and buff off with MF towel
  5. Wax

    My understanding is polish basically scrapes a layer off in order to go deep, is there anything i need to "refill" that digging?

    Does my order of detailing sound good, in other words do i need to add anything else?
u/b-hop · 5 pointsr/AutoDetailing

https://www.amazon.com/PORTER-CABLE-7424XP-6-Inch-Variable-Speed-Polisher/dp/B002654I46 is a great starter and fairly capable, I still use mine for personal and some jobs.

u/ATRAZiiNE · 1 pointr/AutoDetailing

What kind of towels do you use to dry?
I typically use these but not sure if it would be the best for my car
https://www.amazon.com/gp/product/B00A8MZ7IA/ref=ox_sc_act_title_1?smid=ATVPDKIKX0DER&psc=1

u/hellul · 2 pointsr/AutoDetailing

Don't use just water.

You can pickup blue ONR https://www.amazon.com/Optimum-NR2010Q-Rinse-Wash-Shine/dp/B00D8DR0AO/ref=sr_1_1?ie=UTF8&qid=1510851008&sr=8-1&keywords=optimum+no+rinse which you can use as clay lube, detailer, rinseless wash depending on the dilution with your distilled water.

Clay lube: ratio 1:64 or 2 oz/1 gallon



Those types of clay do the job and some people perfer it to traditional clay. I haven't heard of that brand, but i'm sure its the same stuff. I personally have little sponge from Nanoskin. https://www.amazon.com/Nanoskin-AS-019-AutoScrub-Grade-Sponge/dp/B00CUAWJ6G/ref=sr_1_3?ie=UTF8&qid=1510851254&sr=8-3&keywords=nanoskin
I like this better than that "towel" since this has a nice grip.

u/DMAC55 · 2 pointsr/AutoDetailing

Well I've just started getting together my own kit and felt I HAD to get these:

  1. Meguiar's Clay bars and quik detail spray

  2. Butt-load of microfiber towels

  3. Waffle-weave drying towel

  4. Grit-guards

  5. Iron X wheel cleaner

  6. Industrial Spray bottles

  7. Meguiar's Gold Class car wash soap

  8. Meguiar's Gold Class Wax

  9. Purple Power

  10. Proper wash mitt

    I still feel like there are atleast ten other products that I NEED!

    -Pressure Washer

    -Foam Cannon

    -Detailing brushes

    -Sealants/Compounds combined with a proper rotor drill

    -ETC

u/truckosaurus · 2 pointsr/AutoDetailing

If you want that particular DA I would buy it off amazon its 117.99 with free shipping (click add to cart to see the price)

http://www.amazon.com/PORTER-CABLE-7424XP-6-Inch-Variable-Speed-Polisher/dp/B002654I46/ref=lh_ni_t?ie=UTF8&psc=1&smid=ATVPDKIKX0DER

then, since you're kinda new to machine finishing I would go with a microfiber pad and something less aggressive like megs microfiber formula

http://www.detailersdomain.com/Meguiars-DA-Microfiber-Compound-D300-16-oz_p_552.html

u/aydonmill · 2 pointsr/AutoDetailing

If you mean a spray wax, check out D156 by Meguiar's. Solid spray wax that smells really good, and can be used on the paint and any plastic trim. Not exactly sure what the durability is like, though.

Also if you want it for a bit of a discount, I (and others on here) have a wholesale account with Detailed Image.

u/Ready_4_Change · 4 pointsr/AutoDetailing

Porter Cable 7424XP can be found at Amazon and I would highly recommend the following Junkman videos specific to that DA Polisher. Also he states some supplies to go along with the polisher to help with your shopping list for your brother.

PC7424: https://www.amazon.com/dp/B002654I46

Videos: http://youtu.be/KP-eAddv2sk

u/poopfeast89 · 5 pointsr/AutoDetailing

I've never heard of ONR, is this the kind of thing you use?

https://www.amazon.com/Optimum-NR2010Q-Rinse-Wash-Shine/dp/B00D8DR0AO

Would you recommend it? Thanks!

u/wdgiles · 2 pointsr/AutoDetailing

Harbor freight is definitely cheaper, but for ease of use and reliability, you can't go wrong with the PC7424.

u/Chanclaso · 1 pointr/AutoDetailing

I would like a Rupes 21 or 15. If I were to get the 21, it would be with the 5" backing plate. Probably the only thing that I would want. As for Nanoskin, maybe a Nanoskin wash-mitt. These are awesome and make claying a lot faster. The only downside is tighter areas. I would keep traditional clay for that. http://www.amazon.com/Nanoskin-AS-016-AutoScrub-Fine-Grade/dp/B00DOS0LH2/ref=sr_1_2?ie=UTF8&qid=1411408985&sr=8-2&keywords=nanoskin