Best products from r/BITMAIN
We found 17 comments on r/BITMAIN discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 11 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Speedi-Products SM-RDP 1612 16-Inch by 12-Inch Round Galvanized Plain Reducer
- 16-Inch x 12-Inch Galvanized Sheet Metal three piece reducers
- Used to reduce the diameter of a HVAC supply, return or exhaust round duct
- Seal joints with approved duct mastic sealants
- Insulate Ductwork for improved energy efficiency and comfort
- Consult your local building codes for approved installation practices
Features:
2. Tripp Lite Basic PDU, 30A, 20 Outlets (16 C13 & 4 C19), 200/208/240V, L6-30P Input, 15' Cord, 1U Rack-Mount Power, 5 Year Warranty (PDU1230)
- Single phase PDU: safe, reliable power distribution unit delivers 200/208/240V single-phase AC power to multiple loads from a utility outlet, generator or UPS system in a high-density it environment. Ideal no-frills basic PDU for networking, telecom, security, PDU networking, and audio/video applications
- 20 outlet power distribution: The PDU features 20 total outlets rear C13, four front C13 and four front C19. The NEMA L6-30P input Plug with long 15-foot (4.5 M) cord connects to your facility’s compatible AC power source, generator or protected ups to distribute power to connected equipment. Pdu offers 208/240 volts AC, 30a maximum input current
- Switchless design: the switchless design prevents an accidental shutdown, which could lead to costly downtime. Built-in circuit breakers protect connected equipment from dangerous overloads
- 1U metal Housing: reversible all-metal housing faces front or rear in rack. Power distribution unit mounts horizontally in 1U of EIA-standard 19 in. 2- and 4-post racks, as well as on a wall or workbench or under a counter. Also known as - PDU power strip, power distribution unit rack mount, basic rack PDU, PDU 30a, rack mount PDU and power distribution unit 19 rack mount
- 5 year warranty & free tech support: Tripp Lite warrants this product to be free from original defects in material and workmanship for the duration of the warranty. If the product should prove Defective in that time, Tripp Lite will gladly repair or replace it.
Features:
3. Leviton 2620 30 Amp, 250 Volt, Flush Mounting Locking Receptacle, Industrial Grade, Grounding, V-0-MAX, Black
Color-Coding Indicates Voltage RatingsUL/Fed.Spec./CSA/NOMUL V-0 Flammability RatingNEMA and Non-NEMA Configurations
4. C14 to C13 Power Cord - Black, 15A/250V, 14/3 AWG, IEC 60320 - Iron Box Part # IBX-4903-05
DURABLE C14 to C13 Server Rack Power Cord, Blue 14/3 SJT Jacket w/ Flexible Strain ReliefAVAILABLE IN MULTIPLE COLORS AND LENGTHSCONNECT A POWER SUPPLY TO A PDU IN A SERVER RACKSQUALITY CONTROL - Manufactured to the highest standards and tested for Voltage Hi-Potential, Continuity, Polarity and are ...
5. RV & Generator NEMA 10-30P & 10-50P,125/250V,Dryer Power Plug (ETA:7-12 WORK DAYS)
RV & Generator NEMA 10-30P & 10-50P,125/250V,Dryer Power Plug (ETA:7-12 WORK DAYS)
6. NEMA L6-30P to C13 Power Cord - 10 Foot, 15A/250V, 14/3 SJT Wire - Iron Box # IBX-4942-10
- NEMA L6-30P Plug
- IEC C13 Connector
- 10 Foot Length
- 14/3 SJT Wire
- Rated for 15A, 250V
Features:
7. ELC T-3000 3000-Watt Voltage Converter Transformer - Step Up/Down - 110V/220V - Circuit Breaker Protection [3-Years Warranty]
- Up to 3000 Watt Maximum Capacity, Heavy Duty Step Up/Down Voltage Converter Transformer (110/120V 220/240V)
- NOTE: This converter is designed only for European/Asian 220V (Single Phase) , it will not work with American 220 (Dual Phase, Not designed for US 220V)
- Dual Circuit Breakers Protection for Each Voltage (120V & 220V) 1 x 110V Socket, 1 x Universal 220V Socket Weight: 15 lbs., Dimensions: 10.25" x 8" x 4.5", CE Certified
- MAX - 3000 Watt for 30 Mins Use. For continuous use: 1500W. Make sure you multiply x2 the wattage of your item and get a transformer bigger than that
- WARNING: We do not recommend for high wattage heat producing items such as Coffee Maker, Expresso Machine, Toaster & Welding Equipment ETC
Features:
8. Indoor Air Quality Monitor can Real-time Detect Formaldehyde(HCHO) TVOC PM2.5 Accurately and The Color LCD Screen Intelligent Air Quality Detector
- Premium High Quality Background Support
- Backdrop Crossbar 10' of 4 Sections
- High Qulity Carrying Bag for the Whole kit
Features:
9. Tripp Lite Metered PDU, 30A, 18 Outlets (16 C13 & 2 C19), 208/240V, L6-30P, 12 ft. Cord, 2U Rack-Mount Power, TAA (PDUMH30HV)
- 208/240 30A metered Power Distribution Unit (PDU) in 2U horizontal rack mount form factor
- 30A maximum capacity (Agency derated to 24A continuous)
- Attached L6-30P input plug with 12 ft./3.6m line cord
- 18 total output receptacles (16 C13, 2 C19)
- Outlets are arranged in two separately breakered and metered 20A load banks (each with 8 C13 and 1 C19 outlet)
- 2-Year Limited Warranty (Not a Lifetime Warranty)
Features:
10. EVGA Supernova 850 T2, 80+ Titanium 850W, Fully Modular, ECO Mode, 10 Year Warranty, Includes Free Power On Self Tester, Power Supply 220-T2-0850-X1, 850 Watt
- EVGA 850 T2 - "Nothing Beats Titanium"
- 80 PLUS Titanium certified, with 94% (115VAC) / 96% (220VAC~240VAC) efficiency or higher under typical loads
- Fan Size / Bearing: 140mm Double Ball Bearing
- Heavyduty protections, including OVP (Over Voltage Protection), UVP (Under Voltage Protection), OCP (Over Current Protection), OPP (Over Power Protection), SCP (Short Circuit Protection), and OTP (Over Temperature Protection)
- 10 Year and unparalleled EVGA Customer Support
Features:
If possible, you should try to run your S9s on 240V. You should be able to run all 4 S9s on one 30A 240V circuit. Connect them to the circuit via a PDU like this one: https://www.amazon.com/gp/product/B0007YG85A
Ambient intake air temps can safely be up to around 100F. I like to keep them below 95F.
I also like to keep Chip temps below 85C, preferably below 78C.
The most important part of Antminer ventilation design is air replacement (not AC). You need to have about the same amount of fresh air (filtered preferably) going into the front of your miners as is being exhausted out. A good ballpark rule of thumb is 200CFM per Antminer in AND out. You will need intake fans AND exhaust fans.
You can read-up on the factory specs and recommended ambient/PCB/chip temps in the various Antminer user guides available at https://service.bitmain.com/support/download .
Power-cycling your Antminers will not hurt them. If you have an older Bitmain firmware version that allows SSH access, you will preferably want to SSH (Putty) into them (IP address) first and do the following prior to pulling the plug.
(Default SSH login name is: "root" and password is: "admin" (both no quotes).)
type "poweroff" (no quotes), and press Enter.
Close the SSH session.
Wait 5 minutes while the miner cools down, and then physically unplug the power supply to your S9.
To restart, simply plug the power supply back in and let your miner boot up. Takes about 5 minutes before it's mining again.
If you don't have SSH access, don't sweat it, just reboot the miner, and unplug the network cable. Usually by the time it has rebooted and completed the fan test, it has cooled down enough to unplug.
If you don't want to use either of the above methods, just pull/disconnect the power. It's not ideal, but it will do the job.
I prefer to use Slushpool. Helpful instructions here:
https://slushpool.com/help/mining-introduction/?c=btc
Feel free to check out my ASIC setup for more tips at https://www.youtube.com/channel/UCFtqDvpWNSKQs40u2mUiTJg
Good luck!!
Thats a twist lock with the correct c13 end for a computer / bitmain power supply yeah. 14 gauge is nice too... thats what I use from my PDU's to each machine. The 3 prong wont fit the outlet in your picture though, you'll need to rewire it to something like this:
https://www.amazon.com/Leviton-2620-Receptacle-Industrial-Grounding/dp/B00002NAT9/ref=pd_lpo_vtph_23_bs_t_1?_encoding=UTF8&psc=1&refRID=AB56ZCHD7BGJW6QN1DGH
Should be a really simple job for any electrician... just need a box, the outlet and a few minutes.
If you switch out the outlet you could also run one of these:
https://www.ebay.com/itm/Tripp-Lite-PDU-Basic-208V-240V-30A-20-Outlet-15-ft-Cord-PDU1230/112826455467?epid=1837218544&hash=item1a44fb15ab:g:Nz4AAOSw2cNakT4K
which will let you run the number of miners that outlet is capable of (30 amp). 30 amps * 80% = 24 usable amps. Each miner runs around 6amps on 240, so 4 s9's safely from the one outlet (through a PDU of course).
You might have to make your own cord. Thats what I did with that kind of receptacle. You just need this plug and this cord or any other 240v cord that terminates in a c13. That cord will support one miner to be safe since its rated for 15A.
Anyone mining with 110v with luck? or this transformer? https://www.amazon.com/gp/product/B00ER52DMW/ref=ox_sc_act_title_1?smid=ALEWIQ2F9CQDR&psc=1
Holly Shit... Looks like I'm not alone.
My meter model: https://www.amazon.com/gp/product/B071LB8MPZ/
Plugs:
https://en.wikipedia.org/wiki/NEMA_connector#/media/File:NEMA_simplified_pins.svg
See the wikipedia page on it. Your dryer might be listed there. I had electrician install a L6-30 receptacle and a 240(220) / 30 amp breaker.
Then I got a unit like this:
https://www.amazon.com/gp/product/B0053YIUPK/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
you can do a 15 amp, 20 amp version though also as its cheaper, just stay 240v
Does this wire look like it could work for the rig? https://www.amazon.com/NEMA-L6-30P-C13-Power-Cord/dp/B004WODG6A
What's the biggest issue if I use this cord?
I use this one, pretty decent. I can handle 3 to 4 antminers (depending on model). Tripp Lite Basic PDU, 30A, 20 Outlets (16 C13 & 4 C19), 200/208/240V, L6-30P Input, 15 ft. Cord, 1U Rack-Mount Power (PDU1230) https://www.amazon.com/dp/B0007YG85A?ref=yo_pop_ma_swf
Oh I didn't know the L3+ only uses 800W compared to the S9 which uses 1200W
Does that mean I can purchase the EVGA 850W version for the L3+
https://www.amazon.com/dp/B018JYHGOQ/ref=twister_B01AHMAHXK?_encoding=UTF8&psc=1
So please someone correct me if I'm wrong. I believe you need a L6-30r recepticle with a L6-30p pdu and use c13 to c14 cables preferably 14awg. [Cable] (https://www.amazon.com/gp/aw/d/B0027JTJ22/ref=mp_s_a_1_6?ie=UTF8&qid=1522540645&sr=8-6&pi=AC_SX236_SY340_FMwebp_QL65&keywords=c13+to+c14+power+cord) [pdu] (https://www.amazon.com/gp/aw/d/B0007YG85A/ref=mp_s_a_1_1?ie=UTF8&qid=1522540759&sr=8-1&pi=AC_SX236_SY340_FMwebp_QL65&keywords=tripplite+pdu&dpPl=1&dpID=31M8t%2BMq9yL&ref=plSrch)