Best products from r/CuringChamber
We found 3 comments on r/CuringChamber discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 3 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. VIVOSUN 4 Inch 195 CFM Inline Duct Ventilation Fan Vent Blower for Grow Tent
- Powerful Airflow: This VIVOSUN powerful blower with a fan speed of 2500 RPM can create an airflow of 195 CFM; It works efficiently in ventilating grow tents, transferring heat or cool rooms, circulating fresh air, as well as controlling proper humidity, temperature, and air quality for your grow area
- Quiet Operation: Fitted with a flow deflector that concentrates the fan stream and cuts turbulent kinetic energy to reduce sound output to just 30 dB, which does not have any harm to your health and will not disturb your work
- Safety Protection: The motor is ETL listed and features an automatic reset function to prevent overheating or other safety issues; The electrical junction box is made from flame-retardant components for fireproofing
- Simple Hookup: The flanges on both the intake and exhaust ends are simple to assemble with the vent hose by locking tabs; A cord of 5.9-feet long for hassle-free setup; The housing, even the impeller and blades, are easy to detach for cleaning and maintenance
- Wide Applications: It can improve airflow to reduce humidity, block odors, and lower temperatures in grow rooms, basements, or kitchens; Can be used with a variable speed controller (bought separately)
Features:
2. Kuman 0.96 Inch White IIC OLED Moudle I2c IIC Serial 128x64 LCD Display for Arduino Raspberry pi KY34-W
3. Diymore SHT2000 Thermostat Temperature Humidity Controller AC 110V-230V 10A Digital LED Display Multifunction Thermometer Hygrometer
【Overview:】Diymore SHT2000 AC 110~230V10A temperature and humidity controller, just make your life more convenient.【Heating Mode:】Start value < stop value (program automatically determines working mode is heating/humidifying mode). For example, controlling the water heater, heat to 65℃ to ...
Where to start with my update.
I began collecting the parts for the controller. I am using a BME280 for the temp and humidity sensor, this little screen for reading conditions at the chamber, 8 channel relay to control the various electronics, this fan and this filter for fresh air.
Here is an album of updated photos. The first is a blast gate controlled by a servo to control the fresh air flow. When the fan turns on the servo will open the gate and allow the fan to suck air out (more on that later). Next up is the freezer with the collar on. Its not put together properly yet but just a rough test fit shows its looking good. Then I have two inside shots of the chamber itself.
After talking with someone who understands air flow much better than I do, I changed the position of fan and filter as well as direction. The fan is going to suck air out from one side and the other will have the filter on it. This will keep the lid down, where as if the fan pumped air in it could lead to a pressure build up and the lid may crack open slightly. The elbows are put in so its not just the top air that is circulating. I am thinking of turning them so they don't point straight down but for now its good.
The inside shot show the slots made to hold up to 7 bars. I am going to seal in the collar with a piece of wood on the top then fill it with spray foam insulation and silicone it to the freezer.
The other thing that has changed since I last posted was that I was going to try to do the code myself. As I got parts in and tried to put something together it became clear there is no way I can do it. After searching around I put out a bid on upwork.com and now I am working with a friendly fellow from Nepal. We haven't gotten to far but I am excited by his proposal and he will be adding the ability for me to control it from a webpage.
Anyway that is it for now. I can see there isn't much activity on this post or another related post but I am going to follow through with the updates because in my searches for this project I cam across a lot of half finished ideas and projects. RemindMe! 2 months
They seem to be mostly unbranded. There's an example here