Best products from r/MeepoBoards
We found 11 comments on r/MeepoBoards discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 9 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. eRCaGuy Brake Saver Electric Skateboard Charger Adapter DIY Solder Kit: Prevent regenerative Brake Failure, Reduce Battery wear (for Meepo, WowGo, Ownboard, and Others)
- Prevent your brakes from going out! WowGo/Meepo/Ownboard/etc. compatible.
- Your life is worth more than the cost of one of these--guaranteed. Especially useful if you live at the top of a hill.
- Free 1-on-1 email support from the engineer who made this if you have questions (typical response within 3 business days--usually much less).
- Prolong the longevity of your battery by not charging it up all the way. Or, put your battery into long-term storage mode to prolong its life when not in use.
- Assembly (soldering) is required. It does NOT come pre-assembled. WARNING: small parts--keep away from children.
Features:
▼ Read Reddit mentions2. SOLMORE LED Strip Lights, RGB 6.6ft 60 LED Battery Waterproof Flexible Rope Ribbon Lights TV Backlight Battery-powered with Wireless Remote Control,Decoration Lights for DIY Party Living Room 200cm
▼ Read Reddit mentions3. I-WONDER Skateboard Headlights or Taillights, USB Rechargeable Safe Lights, Waterproof LED Flashing Safety Rear Light, Easy to Install for Longboard, Helmets, Bikes and Backpacks
- ✅SUPER BRIGHT TO KEEP YOU SAFE ： The Light with a micro-COB chips(Super energy saving and bright), produces an extraordinarily 210° wide-beamed of light which is eye-catching from all angles. Featured with 5 different modes ,which highly improving your visibility in the dark ,and get noticed on the road.
- ✅EASY TO INSTALL AND TAKE OFF： （Under The Skateboard）The bracket is screwed onto the bridge frame of the slide plate. Then clip the LED lamp on the bracket. （Above The Skateboard）Match gaskets and screw the bracket. Then clip the LED lamp on the bracket. Note：Please mount it properly. The Light should not exceed the deck after mounted, to avoid crash.
- ✅MULTIPURPOSE TAIL BIKE LIGHT： Such as handlebar, the back of a helmet, even your body, you don't just have to be riding a skateboard to use this light - you could be out jogging or walking at dusk and you'll be seen from a great distance, kill two birds with one stone.
- ✅USB RECHARGEABLE： Save your money on batter, give you a good running time, just 2 hours charged time and automatic fully charged cut-off system, built in lithium battery, with environmentally friendly features, run time up to 4 hours.
- ✅COMMODITY CONTENT： Led Light*1, Fixed Bracket*1, USB Cable*1, Washers*2, User Guide*1, Screw M5-45 *2 LED lights specially designed for skateboards. We are committed to improving the customer's shopping experience with our service.
Features:
▼ Read Reddit mentions4. 5 Pcs 5.5mm X 2.1mm Male DC Power Plug Connector + 5 Pcs Screw Lock Female Panel Socket Mount Adapter by Keaiduoa
- ✿Male DC Plug, solder termination with solder bucket and tag
- ✿DC power plug/jack/socket/adapter made of plastic and metal material
- ✿Solder to the solder terminals and connect a DC Barrel plug into the end.
- ✿Application to Media Player, MP3 Player, MP4 Player, Audio-Video Equipment, AV Equipment, Note Book, Cellular Phone, Mobile Phone, Cell Phone, Smart Phone, PDA, Car Audio etc.
- ✿These DC male & female Connectors are attached to a power cable using solder terminals, perfect for making a cable to a desired length or replacing a broken connector.
Features:
▼ Read Reddit mentions5. tangsfire 36V Lithium Battery Charger Output 42V 2A for Electric Bike Batteries Pack DC 5.5mm2.1mmPlug
- Input: 100-240VAC,50/60Hz, Output: 42V 2A Power Max: 84W
- Security protection: OVP(Overvoltage protection)/OCP(Overcurrent protection)/ OLP(Overload protection)/ SCP(Short-circuit protection)
- 42V 2ACharger, Indication Light: Green(full), Red(charging), it stop automatically when the battery is full.
- Global applicable AC input voltage 100V-240V , High efficiency, Soft starting current, reduced the impact of AC input effectively, small size, light weight. Faster and safer charging with our adapter, Intelligent high-speed charging.
- 42V Charger is only suitable for 42V / 36V versions scooters batteries and not for 24V batteries or lower.
- Universal power supply charger with 5.5mm 1 prong plug for 36 Volt Lithium battery. Compatible with Gotrax and many brands. Charger Plug Size:5.5mm(0.21in)x2.1mm(0.08in)x10mm(0.39in)
- CC-CV working mode optimize the life span battery Auto-stop when full charged.
- Eco-friendly, High efficiency, light weight, Heavy duty.
- The case maded of Fireproof ABS friendly to the environment.
- If you are not satisfied with our product, let us know and you will be offered a full refund or replacement. Enjoy this absolutely RISK FREE purchase by clicking the yellow Add to Cart button.
Features:
▼ Read Reddit mentions6. Atom Drop Through Longboard (40 Inch)
- Deck: Maple/Bamboo hybrid laminate with photo heat transfer graphic
- Trucks: Navigator Drone - 40 degree base - 180mm hangers
- Wheels: Atom AREA 51 - 70mm diameter - 51mm wide - 78A - SHR
- Bearings: ABEC 9 with high-speed lubricant
- Grip: Coarse 46 grit
Features:
▼ Read Reddit mentions7. UTG Tactical Low Profile Rail Mount for Ruger 10/22 Rifle
10/22 tactical rail mount1 Picatinny rail with 11 slotsLow profile with middle V-cut for use with iron sightsPrecision machined from aircraft aluminum; contoured bottom perfect fitting the receiverLength: 4.9 inches; weighs 1.2 ounces
▼ Read Reddit mentions8. Ulincos Latching Pushbutton Switch U19C1 1NO1NC SPDT ON/OFF Black Metal Shell with Blue LED Suitable for 19mm 3/4" Mounting Hole (Blue)
Latching switch: Push it, ON; Push it again, OFFMetal shell,100% brand new and high quality, mechanical life for 500,000 cyclesThe switch and LED are separated, LED can be on all the time or only on when switch is on, depending on how you wire itCan be use as a switch for various additional electric...
▼ Read Reddit mentions
Top comments mentioning products on r/MeepoBoards:
Summary
1. eRCaGuy Brake Saver Electric Skateboard Charger Adapter DIY Solder Kit: Prevent regenerative Brake Failure, Reduce Battery wear (for Meepo, WowGo, Ownboard, and Others)
- Prevent your brakes from going out! WowGo/Meepo/Ownboard/etc. compatible.
- Your life is worth more than the cost of one of these--guaranteed. Especially useful if you live at the top of a hill.
- Free 1-on-1 email support from the engineer who made this if you have questions (typical response within 3 business days--usually much less).
- Prolong the longevity of your battery by not charging it up all the way. Or, put your battery into long-term storage mode to prolong its life when not in use.
- Assembly (soldering) is required. It does NOT come pre-assembled. WARNING: small parts--keep away from children.
Features:
▼ Read Reddit mentions2. SOLMORE LED Strip Lights, RGB 6.6ft 60 LED Battery Waterproof Flexible Rope Ribbon Lights TV Backlight Battery-powered with Wireless Remote Control,Decoration Lights for DIY Party Living Room 200cm
▼ Read Reddit mentions3. I-WONDER Skateboard Headlights or Taillights, USB Rechargeable Safe Lights, Waterproof LED Flashing Safety Rear Light, Easy to Install for Longboard, Helmets, Bikes and Backpacks
- ✅SUPER BRIGHT TO KEEP YOU SAFE ： The Light with a micro-COB chips(Super energy saving and bright), produces an extraordinarily 210° wide-beamed of light which is eye-catching from all angles. Featured with 5 different modes ,which highly improving your visibility in the dark ,and get noticed on the road.
- ✅EASY TO INSTALL AND TAKE OFF： （Under The Skateboard）The bracket is screwed onto the bridge frame of the slide plate. Then clip the LED lamp on the bracket. （Above The Skateboard）Match gaskets and screw the bracket. Then clip the LED lamp on the bracket. Note：Please mount it properly. The Light should not exceed the deck after mounted, to avoid crash.
- ✅MULTIPURPOSE TAIL BIKE LIGHT： Such as handlebar, the back of a helmet, even your body, you don't just have to be riding a skateboard to use this light - you could be out jogging or walking at dusk and you'll be seen from a great distance, kill two birds with one stone.
- ✅USB RECHARGEABLE： Save your money on batter, give you a good running time, just 2 hours charged time and automatic fully charged cut-off system, built in lithium battery, with environmentally friendly features, run time up to 4 hours.
- ✅COMMODITY CONTENT： Led Light*1, Fixed Bracket*1, USB Cable*1, Washers*2, User Guide*1, Screw M5-45 *2 LED lights specially designed for skateboards. We are committed to improving the customer's shopping experience with our service.
Features:
▼ Read Reddit mentions4. 5 Pcs 5.5mm X 2.1mm Male DC Power Plug Connector + 5 Pcs Screw Lock Female Panel Socket Mount Adapter by Keaiduoa
- ✿Male DC Plug, solder termination with solder bucket and tag
- ✿DC power plug/jack/socket/adapter made of plastic and metal material
- ✿Solder to the solder terminals and connect a DC Barrel plug into the end.
- ✿Application to Media Player, MP3 Player, MP4 Player, Audio-Video Equipment, AV Equipment, Note Book, Cellular Phone, Mobile Phone, Cell Phone, Smart Phone, PDA, Car Audio etc.
- ✿These DC male & female Connectors are attached to a power cable using solder terminals, perfect for making a cable to a desired length or replacing a broken connector.
Features:
▼ Read Reddit mentions5. tangsfire 36V Lithium Battery Charger Output 42V 2A for Electric Bike Batteries Pack DC 5.5mm2.1mmPlug
- Input: 100-240VAC,50/60Hz, Output: 42V 2A Power Max: 84W
- Security protection: OVP(Overvoltage protection)/OCP(Overcurrent protection)/ OLP(Overload protection)/ SCP(Short-circuit protection)
- 42V 2ACharger, Indication Light: Green(full), Red(charging), it stop automatically when the battery is full.
- Global applicable AC input voltage 100V-240V , High efficiency, Soft starting current, reduced the impact of AC input effectively, small size, light weight. Faster and safer charging with our adapter, Intelligent high-speed charging.
- 42V Charger is only suitable for 42V / 36V versions scooters batteries and not for 24V batteries or lower.
- Universal power supply charger with 5.5mm 1 prong plug for 36 Volt Lithium battery. Compatible with Gotrax and many brands. Charger Plug Size:5.5mm(0.21in)x2.1mm(0.08in)x10mm(0.39in)
- CC-CV working mode optimize the life span battery Auto-stop when full charged.
- Eco-friendly, High efficiency, light weight, Heavy duty.
- The case maded of Fireproof ABS friendly to the environment.
- If you are not satisfied with our product, let us know and you will be offered a full refund or replacement. Enjoy this absolutely RISK FREE purchase by clicking the yellow Add to Cart button.
Features:
▼ Read Reddit mentions6. Atom Drop Through Longboard (40 Inch)
- Deck: Maple/Bamboo hybrid laminate with photo heat transfer graphic
- Trucks: Navigator Drone - 40 degree base - 180mm hangers
- Wheels: Atom AREA 51 - 70mm diameter - 51mm wide - 78A - SHR
- Bearings: ABEC 9 with high-speed lubricant
- Grip: Coarse 46 grit
Features:
▼ Read Reddit mentions7. UTG Tactical Low Profile Rail Mount for Ruger 10/22 Rifle
10/22 tactical rail mount1 Picatinny rail with 11 slotsLow profile with middle V-cut for use with iron sightsPrecision machined from aircraft aluminum; contoured bottom perfect fitting the receiverLength: 4.9 inches; weighs 1.2 ounces
▼ Read Reddit mentions8. Ulincos Latching Pushbutton Switch U19C1 1NO1NC SPDT ON/OFF Black Metal Shell with Blue LED Suitable for 19mm 3/4" Mounting Hole (Blue)
Latching switch: Push it, ON; Push it again, OFFMetal shell,100% brand new and high quality, mechanical life for 500,000 cyclesThe switch and LED are separated, LED can be on all the time or only on when switch is on, depending on how you wire itCan be use as a switch for various additional electric...
▼ Read Reddit mentions
Hey, I'm glad you found the infamous "Computa Pranksta". That's awesome! I hope you enjoy it. It's far from a perfect product but it does the job most of the time.
As for the charge adapter, here is a preliminary listing on Amazon. https://www.amazon.com/eRCaGuy-Electric-Skateboard-Charger-Adapter/dp/B07KNN9PZZ/ref=olp_product_details?_encoding=UTF8&me=. If you'd like one, I'm currently selling the kits (you must solder it together yourself) for $25 with free shipping, or $35 for the pre-assembled version. You'd have to do the purchase direct through me over PayPal. You could do a PayPal "donation" to me here (https://www.electricrcaircraftguy.com/2016/01/contribute.html) for the right amount and make sure your address is correct and all, and make a note what it's for, and I'll mail it out. I only ship once a week though, and this product is guess what?--also not perfect.
I only have 1 pre-assembled version in stock right now, but quite a few kit versions. I'm in the process of a re-design but don't know when it will be complete. The current version as shown on Amazon requires a 4" jumper wire on the back due to a missing trace (done for your on the pre-assembled version of course), and if you use two chargers at once can get pretty smoking hot: way too hot to touch, but still within operating limits of the components. If you think this is for you feel free to make an order. Here's a couple photos: https://photos.app.goo.gl/ob95f5xUcx1QkubB6.
Also, for anyone assembling your own: I have a 30 minute video showing me doing the entire assembly process that I can put on YouTube. It's an unedited video as that's not a skill I have yet (video editing), but it's better than nothing.
I love my Shredlights, but I also found a decent budget light on Amazon that has a mount specific to skateboards as well:
I-WONDER Skateboard Headlights and Taillights, USB Rechargeable Safe Lights, Waterproof LED Flashing Safety Rear Light, Easy to Install for Longboard, Helmets, Bikes and Backpacks https://www.amazon.com/dp/B07SK9G83X/ref=cm_sw_r_cp_api_i_NQIPDbMPZB1BB
It has both a red and white light function with flashing modes, so it can be utilized for either the front or tail.
I also ride with a headlamp on my helmet that pivots so I can control my field of vision in front of me.
For anyone who is wondering about the lights:
Amazon DE: https://www.amazon.de/gp/product/B07NL1J9V4/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
Amazon com: https://www.amazon.com/SOLMORE-Waterproof-Backlight-Battery-powered-Decoration/dp/B073BC8WYW/ref=sr_1_8?keywords=Battery-operated+LED+Strip+Lights%2C+24+Buttons+Remote+Controlled%2C+DIY+Indoor+and+Outdoor+Decoration&qid=1566386367&s=gateway&sr=8-8
Amazon UK: https://www.amazon.co.uk/Battery-Powered-Controlled-Decoration-Waterproof/dp/B07MTY1F2T/ref=sr_1_19?keywords=Battery-operated+LED+Strip&qid=1566386479&s=gateway&sr=8-19
and for the corners i used extensions/quick connectors i already had. But something like this should do it:
https://www.amazon.de/LitaElek-Schnellverbinder-Eckverbinder-Verbindungskabel-Anschlusskabel-Rgb-5050-Nicht-Wasserdicht-Verbinder-10pcs/dp/B01EJ32EXO/ref=sr_1_9?crid=1DV7KKWKB5UPV&keywords=led+schnellverbinder&qid=1566386621&s=lighting&sprefix=led+quick+%2Clighting%2C159&sr=1-9
There are a lot of connectors like this you just need to search for the ones you want.
For the bottom of the battery pack i used strong double sided tape and to clean the corner wires i used black electrical tape.
I bought those https://www.amazon.ca/Connector-Female-Socket-Adapter-Keaiduoa/dp/B07T316DFH/ref=mp_s_a_1_4?keywords=5.5mm+x+2.1mm+Coaxial+Charger+Port&qid=1561681846&s=gateway&sr=8-4 and soldered the female one with the wires from the old connector that I cut off. You'll see once you open your board, it is actually really easy since the connector is actually made to be replaced. Then, you'll want to glue your new connector in place (I used hot glue). MAKE SURE TO UNPLUG YOUR BATTERY BEFORE YOU DO ANYTHING.
Take a look at this. tangsfire 36V Lithium Battery Charger Output 42V 2A for Electric Bike Batteries Pack DC5.5mm2.1mm11mm Connector https://www.amazon.com/dp/B0779RQ4Z4/ref=cm_sw_r_cp_apa_i_ayiBDb94RBYMV
I got the Atom Drop Through Longboard (40 Inch) https://www.amazon.com/dp/B00M3IIGJE/ref=cm_sw_r_cp_apa_i_SB4ODb0RDAZYF it was cheap and had 9 ply
Ulincos Latching Pushbutton Switch U19C1 1NO1NC SPDT ON/OFF Black Metal Shell with Blue LED Suitable for 19mm 3/4" Mounting Hole (Blue) https://www.amazon.ca/dp/B017KP67FY?ref=yo_pop_ma_swf
Yeeco Waterproof LED Digital Battery Meter DC 12V 24V 36V 48V 60V 72V 84V 96V Acid Lead/Lithium Polymer/Lithium Iron Phosphate/NiMH Battery Capacity Indicator 6-120V Voltage Volt Meter Multi Tester https://www.amazon.ca/dp/B01MU6V9RD?ref=yo_pop_ma_swf
UTG Tactical Low Profile Rail Mount for Ruger 10/22 Rifle https://www.amazon.ca/dp/B002GNYCJ4?ref=yo_pop_ma_swf
Valken Rifle Accessory Offset Ring Mount, 1" https://www.amazon.ca/dp/B01IU9DV8K?ref=yo_pop_ma_swf
Angled Wedge Hard Rubber Riser Pads with 1.5" Screws (Blue) https://www.amazon.ca/dp/B01LDO3NZU?ref=yo_pop_ma_swf
Bones Bearings Bones Reds Precision Skate Bearings https://www.amazon.ca/dp/B000FDRQ1S/ref=cm_sw_r_cp_apa_gC.RBbKB0KG0H
Homyl Aluminum Alloy Skateboard Longboard Anti Sinking Gasket Prevent Sag Washer - Black, as described https://www.amazon.ca/dp/B07BKS964N/ref=cm_sw_r_cp_apa_SC.RBbNY1EJVH
https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.ca%2Fulk%2Fitm%2F132701686112