Best products from r/Pieces
We found 12 comments on r/Pieces discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 12 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Gorilla 2 Part Epoxy, 5 Minute Set, .85 Ounce Syringe, Clear, (Pack of 1)
- Strong, permanent, fast and gap-filling; Great for multiple surface applications
- Best for tough repairs requiring a durable bond, gap-filling and solvent resistance
- Dries clear; Ideal for clean, easy finishing
- 5 minute set; Plenty of repositioning time for the perfect fit
- Easy-to-Use Syringe; Separate barrels of resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses
Features:
2. J-B Weld 8265S Original Cold-Weld Steel Reinforced Epoxy - 2 oz.
- J-B WELD ORIGINAL: The Original Cold Weld two-part epoxy system that was designed as an alternative to torch welding. J-B Weld Original provides strong, lasting repairs to multiple surfaces and creates a bond stronger than steel. Perfect for DIY household, automotive, marine, craft repair and much more.
- CURE AND SET TIME: After mixing the tubes at a 1:1 ratio, it takes 4-6 hours to set and 15-24 hours to cure. Once cured, J-B Weld Original can be tapped, filled, sanded, molded and drilled. J-B Weld Original’s set and cure color is dark grey.
- VERSATILE & DEPENDABLE: J-B Weld Original is steel reinforced, has a tensile strength of 5020 PSI and can withstand temperatures up to 550 degrees Fahrenheit (287 degrees Celsius). When fully cured, J-B Weld Original is waterproof and resistant to petroleum, chemical and acid.
- SURFACE APPLICATIONS: Metal, Plastic & PVC, Wood, Concrete, Ceramic & Tile and Fiberglass.
- DO IT YOURSELF: Big or small, you can DIY it with J-B Weld. Our heavy duty epoxy and adhesives repair & restore it right the first time. J-B Weld delivers superior performance, quality, and results for the World’s Strongest Bond.
- Will set in 4-6 hours, and cure in 16-24 hours
- Waterproof, petroleum, chemical, and acid resistant when fully cured
- Can be drilled, tapped, machined, filed, sanded and painted
- Stong and nontoxic after it has set and temperature resistant up to 500F
- Tensile strength is 3,960 PSI
Features:
3. F.e.s.s. Long Churchwarden Tobacco Pipe
- Comes with a Gift Box
- Fast Shipping!!!
- Durable
- Bowl Chamber Depth: 33.2
- Bowl Chamber Diameter: 17.1
Features:
4. Invisible Glass Windshield Chip Repair Kit, 95141
No mixing and cures in sunlightNylon resin chamber is rigid and will prevent leaksWorks on vacuum AND pressure Vacuum removes air pocketsEasy-to-use for even the non-DIYerMade in the USA
5. Diamond Drill Bit Set, DRILLPRO 10 PCS Glass Hole Saw for Tiles Glass Ceramic Marble Bottles DIY,6mm - 30mm
- SMALL RESISTANCE: Small incision resistance, opening speed is quickly, easy removal of chips and other advantages.Also help to open accurately. Large chip holes to ensure that when the punching smooth, punching accurate.
- DURABLE: Nickel-plated with a diamond dust coating offers superior performance and cutting strength.Extended service life.This diamond drill bits are high quality and good performance that excellent for making clean and accurate hole.
- IDEAL FOR: This diamond coated core drill bit removes a complete circle from glass, marble, tiles,granite, ceramic or other.Reduced drill speeds, low drill pressure and increased use of water lubrication will extend drill bit life considerably.
- TIP: Can be used with a standard electric drill (not included), Always use lubrication (water), otherwise the diamond core drill will burn. Warnings: Not for use on Concrete or for depths beyond about 1/2"; Water is required for lubrication when drilling.
- 10 SIZES: Total 10 different sizes (6mm,8mm,10mm,12mm, 14mm, 16mm, 18mm, 20mm, 22mm, 30mm).Different sizes meet your different needs,help you in different places.
Features:
6. Skyway Couch Tobacco Pipe Stand Holder - Black
- Tobacco Pipe Stand Holder Rack Holds 1 Pipe
- Couch Design is Unique and Has A Beautiful Black Finish
- Keeps Tobacco Pipes Accessible and Ready To Use
- Perfect Way To Display A Pipe
- Perfect Gift For Any Pipe Smoker and Measures: 4 x 3 x 2 Inches
Features:
7. 16mm Diameter Diamond Coated Core Drill Bit Hole Saw
16mm Diameter, DIAMOND COATED CORE DRILL BITSize: 16mm outside diameter, 8mm shank, 35mm depthRemoves a complete circle from glass, tiles, marble, granite, ceramic or other materialsOnly needs water for lubricationCan be used with a standard electric drill.
8. Five Star PBW - 1 lbs - Brew Cleaner Buffered Alkaline Detergent
- PBW is an alkaline, non-caustic, environmentally and user friendly cleaner
- Cleaner is very effective in removing thick, difficult, and caked-on organic soils
- Effective substitute for caustic soda cleaners and household cleaners
- Can clean items that cannot be reached with a brush or sponge by simply soaking and rinsing
- Safe on skin as well as stainless steel, rubber, soft metals, and on plastics
Features:
9. Zen Bundles Zen Pipe Cleaners Hard Bristle, 132 Count
- Zen the name you know & can trust for all your cleaning needs & 420 help
- Clean & repair old antique tube radios, t.V.'S, ham radios / receivers (especially from 1918-1965)
- Such as philco, rca, admiral, Zenith, hall crafters, sears, Brewster, crossly, firestone, plus hundreds more
- Arts & crafts projects for many pre-school, kindergarten, elementary & jr. and high school teachers, as well as Sunday school classes
Features:
10. Waterproof Case Pelican Storm iM2950 Case With Foam (Black)
- 29" x 18" x 10.5" Interior Dimensions. Two Padlockable Hasps
- Press and Pull Latches
- Rugged In-Line Wheels
- Molded-In Lockable Hasps. LID DEPTH: 2.00 inches,BOTTOM DEPTH: 8.50inches ,TOTAL DEPTH: 10.5inches
- Three Double-layered, Soft-grip Handles
Features:
11. StonyLab Glass 500ml Heavy Wall Borosilicate Glass Filtering Flask, Bolt Neck with Tubulation - 500ml
- Used for pressure filtration; or to increase flow rate when some concentrated solutions are slow or difficult to filter under normal pressure
- Made of borosilicate glass; capacity: 500 milliliters
- Flasks have a narrow mouth and tooled top finish
- Special notice: As this item is handmade, please allow an error range of 2~3mm
- StonyLab ensures high quality products and premium customer service; if received damaged, please contact us immediately; we will solve it until satisfied
Features:
Easiest way to fix it. Go to wal-mart or target and buy this or order it from amazon. clean the edges and follow the directions. works perfectly. I did this for 3 of my pieces that broke. It's very clean and will be as good as new. Make sure you don't overapply it so that it oozes out inside. Might be bad for the downstem. It's the cheapest and easiest way to do it. Best of luck! toke on
Edit: Epoxy does not melt or dissolve by acetone so you can clean it with acetone after fixing it too! Source
>There are two broad classes of plastics, thermosets and thermoplastics. A thermoplastic can readily be dissolved or melted, while a thermoset cures and changes. Once cured, it forms a tough, crosslinked network which resists solvents and will degrade instead of melting. Epoxy is a thermoset. The advice to trim or slice it off is good. Solvents like acetone or whatever, unless extremely powerful and dangerous, will have little effect on a cured epoxy. Things that easily swell and dissolve epoxies will do the same with rubber or plastic gloves or portions of your anatomy.
The glass doesn't get extremely hot, but it does get pretty warm when you're lighting the bowl, so I don't trust glues. I would use JB Weld, it's extremely strong, water resistant and heat resistant up to 500 degrees F. It won't last if you put the flame right to it, but it will easily handle the low heat from the bowl. Make sure to lather it on thick on the the broken edges, and around the outside to create a support. it won't be super clean, but if you lather on enough it can be sanded down to be smoother.
http://www.amazon.com/F-e-s-s-Long-Churchwarden-Tobacco-Pipe/dp/B004ECU1W2
Picked this one up a couple years back. Ultra cheap, pretty durable, massive bowl (as it's intended for tobacco), filter is incredibly hard to clean so I just removed it. Best of luck!
If the seal is still airtight its salvageable. Slather some Clear Epoxy on or some of this. Just make sure it gets into the cracks but not into the inside of the tube.Good luck
Sorry for taking so long to respond.
We held the drill on an angle we wanted while drilling the hole. Used a drill we thought was the size too small but with the angle it ended up perfect.
used these drills
And
this stem
It was $10 from amazon
It works great.
i used a circular glass drill bit like this one. i got it at my local hardware store but you can prolly find it at a HD or Lowes. just make sure when you drill you use a lot of water or your glass will have a greater chance of breaking and the drill bit will get ruined from the heat generated by the bit
I used PBW, which brewers use to clean their gear when making beer. It's non-toxic and works incredibly well. What I personally do is place a stopper in the downstem hole, and then place a TBSP of PBW into the bong. I then fill the bong with water as hot as I can get it and let it sit. After the water has cooled some I will shake the bong up a bit, and then do a salt and ISO wash. The glass always looks brand new, without any signs of resin. This has worked for completely cleaning my most complicated pieces and is completely non-toxic, and cheap, as a $10 tub of PBW lasts years:
http://www.amazon.com/PBW-Five-Star--1-lb/dp/B0064O7XBA/ref=sr_1_1?ie=UTF8&qid=1407519502&sr=8-1&keywords=pbw
http://www.amazon.com/Bundles-Pipe-Cleaners-Hard-Bristle/dp/B000W5R6UA i use these a lot for my warez too
giyf
Here is what you want...
https://www.amazon.com/gp/product/B076GPVFSJ/ref=s9_acsd_topr_hd_bw_bQcZad_c_x_w?pf_rd_m=ATVPDKIKX0DER&pf_rd_s=merchandised-search-3&pf_rd_r=4AAT93DBSAKGEHT8Y7YD&pf_rd_r=4AAT93DBSAKGEHT8Y7YD&pf_rd_t=101&pf_rd_p=4ffede3a-006f-57cc-82f4-a39b63f61991&pf_rd_p=4ffede3a-006f-57cc-82f4-a39b63f61991&pf_rd_i=393378011
Fuck, I just typed it all out for you and then it went back a page and erased. I used these and bought a separate glass bowl that was jb welded to the lid. It is set up 3x2, and it is set up like a normal bubbler. I have plastic elbows connected to the incoming airflow that becomes submerged, and then a line exiting the same jar with a hole above the water line. I repeat 5 times and connected all the hoses. I attached each jar to each other with double sided tape and electrical tape. A pair at a time, then taped them all together. After letting everything set, I sucked the air to see how it worked and I heard a nice whistle from the bowl. I knew it was ready, I then drilled a carb in the bowl jar and was ready to go.
Oh also, the holes are drilled at 1/2 inches with 5/8 inch vinyl tubing. Sorry if its confusing or kind of vague, it is a lot easier to explain in person. If you need anything clarified or other things I left out, just ask.
Edit: The jar bottoms are connected to each other, I thought it would be easier for filling but was wrong, you kind of just have to fill it from where you suck, it will be easier to empty though.