Best products from r/RetroPie

We found 320 comments on r/RetroPie discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 755 products and ranked them based on the amount of positive reactions they received. Here are the top 20.

Top comments mentioning products on r/RetroPie:

u/e39 · 4 pointsr/RetroPie

Disclaimer: I'm here, ready to answer any specific questions ... but the following is a copy & paste job. The topic of arcade parts comes up quite a bit.

(begin paste)


There's a lot to consider when choosing a joystick. It all comes down to personal preference and how much you want to spend.

American Style:
Happ parts were infused in arcade machines in the 80's and early 90's. if you grew up playing Mortal Kombat and Street Fighter 2 at your local bowling alley, you were touching Happ parts. Also, these setups were designed to withstand a thrashing. The sticks have a very heavy re-centering spring. The buttons (when paired with with a 75g Cherry Microswitch) provide a ton of bounce.

Durning this era, Happ sourced parts from a European manufacturer, Industrias Lorenzo or "IL". Now, Happ is owned by Suzo, operating under the name "Suzo-Happ" and sources all of their parts from China.

Industrias Lorenzo still exists today and sells the same parts from the golden era of US arcade gaming. Their "Euro Joystick" is awesome.

Personally, I built a 12 button (Start, Coin, A, B, X, Y, L, R, L1, R1, L2, R2) w. joystick using all IL parts and Cherry Microswitches. It feels exactly like the arcades I grew up in.

Japanese Style:
Sanwa rules the scene. These joysticks are extremely tight and compact, allowing the user to quickly get off button combinations without misfires. There's quite a bit of customization too (dealing with directional gate/restriction plates, colors, etc).

Everything about the Japanese style stick is built for efficiency. The buttons are very sensitive and require less force to trigger.

USB Encoder:
If you're not doing any competitive play and aren't considering multi-purposing the controller for a modern console, the Zero Delay USB Encoder is magnificent. It's very easy to use, comes with the wires and works as designed. Note: You may need 1 extra cable if you're using a Japanese style joystick.

A heads up:
Be weary of the arcade joystick kits you find on eBay and Amazon. There's no way to vouch for the authenticity or quality of the parts. Again, it all comes down to budget. These kits will get the job done, but you may experience some in-game frustrations when certain things just don't feel like they're working (especially throwing a fireball in SF2).

I know this is a ton of information to absorb and research, but I found building an arcade stick to be quite enjoyable. Also, you don't need to be a master electrician to make this stuff work. It's mostly plug and play.

I've purchased parts from:
Paradise Arcade Shop
Focus Attack
UK Arcade World

The kits seem like a better deal, but if you piece together what you need, you gain a lot more customization (colors) and peace-of-mind (legitimate, authentic parts).


(end paste)

It comes down to personal preference and budget. Also, take a look at the games you want to play the most. Arcade games used various hardware setups. Find the one that mimics the cabinet belonging to your favorite titles.

(Ex. As a Mortal Kombat fan, it would feel super weird to play with a Sanwa stick.)

u/johnnyringo771 · 2 pointsr/RetroPie

Some people have PMed asking for more info, so I may as well put it here.

I used the following:

8inch 28AWG High Speed Male to Female HDMI® Port Saver - Black

For the hdmi port. I also bought another hdmi piece, like a corner basically, it's in some of the early pics, but I didn't use it in the final build.

Tiesto USB Hub 2.0 4-port/4 port hub USB 2.0 Speed Cute Octopus Design - BLACK
I removed the black case on this as well as the black rubber around the usb ports. Then basically hot glued the ports in place against painters tape to make it even and smooth.

Your Cable Store
6 inch USB Micro male to female OTG extension cable

I cut these in half and spliced it into the original Gamecube power switch/button. That way I can leave my pi plugged in and switch it on like a normal console.

Evercool 60x60X10mm 5v Ball Bearing Fan, 3 Pin EC6010M05CA
I set up these fans to run off the main power, so they turn off and on with the pi.

To take apart each Gamecube, i bought this screwdriver.

Also got each person a Buffalo Classic USB Gamepad for PC
And a Retrolink N64 Style Classic Controller For PC

I forgot to mention, I took apart and weighted the buffalo classic usb controllers to be closer to the weight and feel of the original snes controller.
The exact increase in weight is about 10 pennies, but I used 8, 4 on each side, inside the controller, in stacks, glued in, because 8 fit better than 10.

It's a really tiny thing, but if you weight one controller and then hold an unweighted and a weighted one to compare, the unweighted one feels like a toy.

The N64 controller felt decently heavy on it's own. (Plus the rumble pack used to make them super heavy and I wasn't going to try and match that weight.)

Other things, these have in them the pi2 with 1gb of ram. I bought the 2 amp power supplies that are recommended for the pi.

I also bought some other odds and ends: ethernet couplers, each pi has a 16gb sd card in it.

I also replaced the power switch in my final one (the silver one) because I damaged the original switch. I used these switches.

I bought Rust-Oleum metalic base and Dupli-color spray paints.

Tools/materials used:
Bought a dremel, didn't need it.

Used my soldering iron and clamps constantly.

Used a lot of hot glue and gorilla glue.

Mod podge for applying the logos to the top of the cases. I also had some spray sealant from another project I put on the logos, before I applied them to the cases, so the ink wouldn't smear.

I used a fair bit of heat shrink and electrical tape. Also wires with couplers so the entire bottom of the console can unplug from the top if I need to repair something. Basically these though not the same brand.

Much of my job is working with electronics and soldering so this was all fairly easy for me. If you're new to building and soldering, please be careful. I've cut myself and burnt myself quite a few times. Be more careful than me.

u/goldfingeroo7 · 8 pointsr/RetroPie

I wanted to show off an arcade cabinet that my brother in-law and I built.

Imgur Gallery

We designed the cabinet in 3d to make sure everything would fit. Then cut out everything using a CNC router. We used wood glue and wood putty to put everything together. For the monitor we used a Dell 17" (we had lying around) mounted portrait. The guts of the arcade are

  • Internal PC fans used for cooling. We did this because the monitor would get a little warm after playing. Plus it couldn't hurt. Not too loud either.
  • Speakers are from an old kiosk that we were throwing away at work. I did look at some other solutions but since I already had them and they were powered, we decided on using them. It also helped that the size matched the PC fans so the hole pattern would look nice on the side
  • Buttons and Joysticks were purchased from [Amazon].(
  • We used a Raspberry Pi 3 purchased from Amazon.
  • For power, we took a power strip and removed the plug and bought (this power socket)[] from Amazon. Soldered the connections from the power strip to the power socket.
  • Still waiting on the custom piece of tempered glass that will go on the top.
  • It's got 2 coats of stain and a couple of coats of polyurethane to protect the wood.

    In all it took us a couple of weeks to design in 3D. My brother in-law did all this work. He also cut out everything and assembled the shell. I did all the internal wiring and software side of things. It is running RetroPie 4.0.2. The only really PITA is that this is a cocktail arcade. Most if not all the games needed a custom shader to correctly implement the rotation and dual flipped screens. A big shout out to hunterk from ([] forums for helping me with this. It turns out that NES, SNES, Arcade, etc... needed their own shader to correctly display the image to both users. Also, the mame emulator has the ability on some 2 player games, to set cocktail mode. That way, when it is the 2 players turn, the screen auto rotates so they can play on their side.

    We were pretty impressed with ourselves when we finished. We built it to give away at a foundation raffle a couple of weeks ago and the winner was very excited to win it.

    I'll be glad to answer any questions you guys/girls have about the build. I plan on putting the glsl shaders on my github so others using the RetroPie OS in cocktail mode can use them.
u/8Bits1132 · 3 pointsr/RetroPie

The CanaKit ones are usually good as a starting point (unless you don't want to buy the components individually, though as another person said, the power supplies that ship with them aren't the greatest.

If you DO want to buy the components individually, however, you only need to get the board itself, an optional case, and the power supply. Here's what I've seen most people use.

  • Raspberry Pi 3 B+ (around $35 USD. It's the most powerful iteration of the Raspberry Pi. It might fit your needs, as it can play PS1 games pretty well.
  • Official Raspberry Pi Power Supply (5V/2.5A)

    You could also invest in heatsinks or fans if you want to keep the Pi a bit cooler in temperature. Or, you could also buy a Flirc case, which is around $15 USD, which acts as a giant heatsink. It's one of the more popular cases around here, and for good reason. It's very reasonably priced in my opinion, and it does a good job at keeping the Pi nice and cool, so you don't need a fan.

    Speaking of cases, if you want that retro console look, there are some pretty good options, with one of the most well known case makers being Retroflag. They don't come with any form of cooling like heatsinks and fans, so you'll have to provide those separately.

    If you are asking about controllers, you can use both wired USB or wireless Bluetooth controllers as well (though you'll need to have at least a USB controller or a keyboard connected to the Pi for the first part of setting it up which will ask you to configure your controls which work across the RetroPie environment (that includes EmulationStation which is used to launch your games, and RetroArch which powers most of the emulators included with the default RetroPie install).

    You can read the RetroPie documentation for more information on RetroPie itself too.
u/Pastoolio91 · 1 pointr/RetroPie

Good to find someone else in my shoes, lol. I was in the exact same position a couple months ago before grabbing a Pi, so I'm not an expert by any means, but I've learned a few things.

As for plug and play kits, I'd avoid the ones with NES/SNES style cases as they have horrible cooling. If you're planning on using it as a RetroPi, you'll definitely need some better cooling. For passive cooling, you'll need something like the FLIRC case, which basically turns the entire case into a giant heatsink ( or for active cooling, I'd suggest grabbing a cheap acrylic stack with a small 30mm fan off Amazon ( Keep in mind that these are Pi 3 B+ cases, and they won't work with the Pi 4 as the USB and ethernet are switched around, plus different HDMI ports.


For your first Pi, a kit is nice as it includes heatsinks and a decent power supply. If you want to use RetroPi then having a kit with an SD card that includes NOOBS wont matter, as NOOBS doesn't let you install RetroPi. Also, the cases that come with CanaKit and Abox have terrible cooling if you're running something heavy like RetroPi, so I'd recommend getting these:

Rasbperry Pi 3 B+ Basic Kit:

FLIRC case:


Other than that, you'll just need an SD card to flash with RetroPi, maybe a USB stick to transfer ROMs over with, and a controller. 8BitDo make some really solid retro replica controllers so I'd suggest that possibly.


As for a gaming PC, you could easily run most ROMS on a low end gaming PC, so if emulation is your main goal then you could easily build a 500-600 PC that would kick ass for ROMS. I mean, my Chromebook can run RetroArch pretty easily, so you don't need a ton of power. It's just that the Pi is a tiny SoC running an ARM chip so it's different than a full fledged x86 PC.


The Pi 3 B+ struggles with N64 and PS1 some, so waiting for the Pi 4 to be RetroPi compatible would likely be the cheapest option to get yourself going. I have high hopes for it with regards to the N64 and other systems from that generation.

u/Sadistic_Sponge · 6 pointsr/RetroPie

I haven't heard any word about 4.3 coming out, but updating is very easy from within retropie.

Some stuff from an old post that is applicable here:

Don't waste your money on the heat sinks, they don't do much without a fan. The nintendo case is cool, and it will work for the NES emulation, but it will not cut it for N64, since you'll probably overheat with an overclock. Overclocking is basically required for N64 to run even sorta smooth. Instead, get a better case that can handle heat effectively. I use; but others have used a Flirc with great success:

It's worth going for function over form in this scenario.

As for other advice/tricks for setup:

  1. Install this mod to minimize errors where phanton controllers and keyboards end up in the player 1 slot:

  2. Set up WinSCP and SSH to transfer roms easily:

  3. Swag polish:

    Get video previews set up:

    Get slick loading splash screens set up when you start a game:
u/Alfonzo9000 · 3 pointsr/RetroPie

I'd buy a Cana Kit since it has everything you'd need to have a complete pie.
That's the most full featured Pi3 kit they have but there are other more affordable options.

There are tons of tutorials online but I suggest you look up ETA Prime on YouTube because he helped me a lot with setting up Emulation Station and getting tons of games on my Pi.

As for controllers, the wired iBuffalo ones are great but if budget concerns aren't an issue then get the 8Bitdo SNES30. It's a Bluetooth SNES controller with a 1 to 1 look and feel. It's pricey but you really won't regret it.

Good luck and have fun! Hope she enjoys it!

Edit: As a side note you want to invest in a case with a fan! There are ones that look like a tiny NES or SNES and seem neat but have next to no ventilation so your pi WILL overheat. I made this mistake and wasted $20.

u/Euronymous316 · 1 pointr/RetroPie

The power supply needs to be a micro USB one (sorry I forgot to mention that). So like a phone charger. I find my Samsung phone charger works fine - it is only something like 2.1A so occasionally I get slowdown (a little lightning symbol appears on the screen which means "Low voltage"), so ideally find a 5V micro USB charger at 2.5A for optimal performance. On the USA Amazon site, this one is good: But if you have a micro USB phone charger already, you could just try it and see if it works.

For the control pads, yeah if they work with a PC through USB then it should hopefully work on the Retropie as well. It's pretty much plug and play - when you put a new controller in, it asks you to press some keys and it is all set up automatically.

Don't know which websites in Canada would be good sorry. Where I am from I just went into a local electronics shop and got everything (Raspberry Pis are actually pretty common, you don't even have to go to a dedicated computer shop).

u/Echoj2 · 1 pointr/RetroPie

Friendly warning, asking for the name of sites with roms is against the subreddit rules, so I advise you remove that question from your post. Posting links to such sites or the ROMs/BIOS themselves on the subreddit is also against the rules.

Follow that guide. Several emulators are included with the RetroPie image by default, and any others you find that you need later can be installed within the RetroPie Setup Menu.

As for controllers, some people like these

but their price has been all over the place due to low supply, high demand, or sellers just realizing they can increase the price and people will still pay.

I can't attest to any other controllers, though someone else will probably give you better recommendations. You'll want a controller with analogue sticks if you plan to play PS1 or N64; I wouldn't advise getting your hopes too high with N64 though due to the fact that the Pi3 can't run N64 perfectly. Not sure if there are any other consoles that the Pi3 can emulate that need analogue sticks.

As for pitfalls...

You might want to get a case with a fan so you can overclock, though people mostly do that when they are trying to make N64 closer to playable, but I've seen some people say it does help push a few problematic SNES and PSX games to 100% speed. I couldn't stand the noise of the fan though and am waiting on a jumper cable pack from eBay so that I can under-volt the fan with the 3.3v pin 1.

A USB 3.0 card reader is another nice thing to have, if you have a PC with a USB 3.0 port that is. Backups take a fifth of the time they took compared to my USB 2.0 card reader.

I use a on/off switch as well, after properly shutting the Pi3 down and waiting ten seconds for all the shutdown stuff to complete of course. You don't want to be yanking the USB power out of the Pi3 because of port wear and unplugging from the outlet isn't very easy to do for most. You could always just leave it on all the time like many other people do and I get a lighting bolt (low power) alert for two seconds at boot during my custom startup video due to the one I posted below. Guess I'll see how it affects overclocking later.

u/Maindric · 17 pointsr/RetroPie

Several years ago I got a Raspberry Pi model A and it lagged in most SNES games. Needless to say, I was disappointed. Well, I just finished this SNES RetroPie build and I am happy. Here is the parts list I used:

u/ragormack · 1 pointr/RetroPie

For safe shut downs, charging warnings, and charging status - Adafruit PowerBoost 1000 Charger - Rechargeable 5V Lipo USB Boost @ 1A - 1000C-Purchased from amazon,

Shell used-Gametown® Full Housing Shell Cover Case Pack with Screwdriver for Nintendo Gameboy Classic/Original GB DMG-01 Repair Part-White (pick whatever color you want)-Purchased from amazon,

Screen used- BW 3.5 Inch TFT LCD Monitor For Car/Automobile – purchased from amazon, (side note here is that in order to make this fit nicer, I installed it upside down in the case.

Speak used - uxcell 16pcs 27mm External Magnetic Speaker Loudspeaker 8 Ohm 0.25W, purchased from amazon, (do not put ANYTHING on the top of the speaker when you install or it will not work.

Prototyping bread board, I purchased from amazon but it is no longer available at the link.

I used this PCB for the buttons on 1 build, the drill guide is VERY useful for this project. - 4 Button PCB For Gameboy DMG-01DIY Pi Zero Made In USA With Grounds and Hole Guide BY:Atomic Market, purchased at amazon,

L-R buttons- 100 Pcs 6 x 6mm x 9.5mm PCB Momentary Tactile Tact Push Button Switch 4 Pin DIP, purchased at amazon

28 Gauge Wire - Ribbon Cable - 10 Wire (15ft), purchased at amazon, (I recommend going to a smaller (higher) gauge than 28. 30 or 32 would have made it a lot easer but 28 will do.

Indicator lights, Uxcell a11092800ux0119 Uxcell (Pack of 75), purchased at amazon, (these are totally optional)

Resistors and capicitors (audio), purchased from Note: heres the guide I used for the audio too!

Old Gameboy game cartridge. For aesthetics.
Headphone jack, ebay,

Volume wheel, ebay,

Micro SD card (16 GB minimum)

Female Micro usb Port, (I know I did buy these but I can’t find the link. I bought female micro usb ports to make charging easier.)

I want to say this is the battery that I used, specifically because after taking the shell off it was the perfect fit inside of a gutted Gameboy Game cartridge-

3d printed button wells-

Extra buttons-

Screw bracket-

I got A LOT of buttons, glass screen shields, the other three builds button PCBs, some stickers, seriously a lot of stuff from his store is unfortunately closed as he has had life catch up to him and has some shit to attend to. If he comes back online show him some love.

Stuff I got from kitsch
PCB board with LR input points
Buttons for X/Y (you can opt to just get replacement snes or an extra set of Gameboy buttons.
Glass screen that fit the GB shell after removing extra plastic

And obviously you should have a pi zero/w as well a shit ton of patience.

u/IronmanGamer24 · 1 pointr/RetroPie

The old skool one which is now kintaro is popular, but known to make the pi hotter. I put a fan in it and run it fine with overclock.
small nes case

There's a another china one that's interesting and gained popularity. It has function power buttons, spot for a fan. NES style as well. Have to wait for in stock again though. Both run for $20
NESPi Case

u/tm258 · 1 pointr/RetroPie

I've only used the Logitech F310 with it. I think it's a good controller in general. Was super easy to set up with RetroPie the first time I turned everything on, and has worked well with the few nes, snes, and genesis games I've used it on so far. I also found that when I plugged a second one in I didn't have to do any extra configuring. It immediately had the same button mapping as the first controller, which was nice. I don't know for sure if the same thing would happen for other standard usb controllers though.

I'm kind of interested in buying a couple of the Buffalo SNES-style usb gamepads too, to give it that extra retro feel. They seem pretty nice.

Here's that Amazon link for the case/fan combo.

Let me know if you have any more questions! :)

u/JDFanning · 3 pointsr/RetroPie

Haven't had any issues with my China 5v 3A adapter -- but I'm not OC'd - try reverting back to standard clock and see if the bolt goes away - if it does you might need to get a larger/better power supply ( I've seen a few reports saying the Canakit supply doesn't actually provide 2.5A @ 5V )

For example this review on Amazon by Chris Satterleeon April 4, 2016 ( )

He does some Testing and includes a chart which shows it and says :

An interesting point is where the curves cross their rated current values. The Kootek 2.0A supply crosses 2.0A at about 4.6V (2.04.6 = 9.2W). The Canakit 2.5A supply crosses 2.5A at about 4.5V (2.54.5 = 11.25W). Both of these are well below 5V. Probably high enough that the RPi won't crash, but cutting it close.

Another interesting point is where the curves cross 5.0V. The Kootek 2.0A supply crosses 5.0V at about 0.8A (0.85.0 = 4.0W). The Canakit 2.5A supply crosses 5.0V at about 1.0A (1.05.0 = 5.0W).

People who are claiming that this supply doesn't deliver 2.5A are correct - if they are expecting it to deliver 2.5A at 5.0V. But what is important is whether the supply is sufficient for the RPi 3. All I can say for sure is that it does deliver proportionally more power than a 2.0A-rated power supply that has worked fine for me with the Gen 1 RPi B+. For that reason, I'm giving it four stars. "

So by the time it hits 2.5A the voltage has dropped to 4.5V which may be the reason the lightning bolt is showing if the case adds even a small amount more of drop by using the GPIO pins for the power in !

u/TheSecondTier · 1 pointr/RetroPie
  1. Yes, even with overclocking the Pi won't handle PSX and N64 perfectly. I don't emulate those systems because I'm using an old model B so I can't really tell you much about specific performance, but I have heard that Super Mario 64 and Mario Kart work.

  2. ¯\_(ツ)_/¯

  3. It gives you a warning about potentially voiding your warranty. I've tried overclocking both of my Pis and the older one can't handle anything above Medium without getting unstable (freezes and crashes), the Pi 2 I haven't really tried an overclock over Medium but it works fine at that setting. It kind of depends on your Pi, some can handle the highest default overclock with no issues.

  4. It appears that English isn't your first language, so I'm not sure what you mean by "family controller". I use the Buffalo SNES controller, as do many other people, and it works great.

  5. I'm using the default theme and the console-stripe splash screen. I didn't look into themes very much, though, I just wanted the cool splash screen.

  6. Follow the wiki, it's super informative.
u/DrakeFS · 2 pointsr/RetroPie

You do not need fans. This CanaKit is probably the only one I would suggest. The power supply has worked very well for me and it is basically the same price as buying a 3b+ and power supply separately.

The issue I have with most kits, is that they are trying to make as much money as possible on a lot of parts. This means you are going to be getting cheap parts. There are much better cases, like the Flirc Case(I use this one) or the Retroflag cases(if you want that retro console look), both of which are available on Amazon.

You would be better off getting some 8bitdo or iBuffalo controllers. Cheap controllers just do not feel right. While I have never used the CanaKit controllers they do not review well.

Finally, the SD card. Always buy this yourself, from a good brand and from a good vendor. Samsung (what I buy) and Sandisk seems to be the best reviewed and performing SD Cards. Performance is not that big of an metric for the Pi 3b+ though. You will want reliability from your SD card. A cheap card will cause more problems than what they are worth in my experience.

Just know, building a RetroPie without having anything already will cost you ~$100. They are not cheaper or easier than SNES classic. That being said, if you like tinkering, RetroPie's are a hell of a lot more fun.

u/TrashSlutArt · 2 pointsr/RetroPie

I got a canakit with the B, I feel like I’ve seen that there’s issues with Retropie and the B+, but maybe I’m thinking of something else... mine came with a sandisk microusb. Used etcher on my Mac to format and write the retropie image. I got the innext controllers and I think they work well (two for $14.99 on Amazon). In the future I may buy a case with a fan built in, but that’s just something I’m interested in, not too worried about it.

This is what I got and it came with everything as listed

I’ve had a lot of fun with it, hope it works out for you

u/cxg-pitch · 2 pointsr/RetroPie

You can make lots of cool stuff if you've got the skill/time, but if you just want something simple, the Old Skool Tools NES case rocks. Doesn't come as a kit that I know of, but just grab a Pi, power supply and microSD card and you're set. It's super easy to put together. And if you want an extra little DIY project, you can add a power indicator light or maybe a functioning ON/OFF button. That's what I did with mine, and I love how it turned out.

u/Thranx · 15 pointsr/RetroPie

Any time an SNES case comes up, I have to pimp the Super Kintaro. It's REALLY well made. Great heat sink, buttons work... just an awesome case, and suprisingly well prices for the high quality.

u/wickedcoddah · 9 pointsr/RetroPie

Parts List:

Power Adapter

Raspberry Pi

USB Super Nintendo Controller (This is the best one I have found so far)

HDMI Cable

WiFi Dongle

Other Items you will need:

USB Keyboard

Monitor or TV with HDMI Support

Now you dont have to use these parts exactly, there are plenty of other parts you can use. I am pretty sure that you can play Roms up to Playstation 1.

There is also a new Raspberry Pi 3 that is compatible with the RetroPie software which has WiFi and Bluetooth integrated into the board.

Helpful Video's to tackle technical issues with your RetroPie:

Here is the Case I found on Etsy. There are plenty of other sellers but this guy was great!

u/Paranoid_Pancake2 · 3 pointsr/RetroPie

SD Card:

CanaKit Raspberry Pi 3 Kit with Clear Case and 2.5A Power Supply Use the heat sinks it comes with. Mine got a little warm yesterday but I was using it for a few hours, nothing crazy though. I don't think you will need a fan, the case has an open rim around the top.

Classic USB Gamepad

AmazonBasics USB 2.0 Extension Cable - A-Male to A-Female - 6.5 Feet (2 Meters) The controller cord is pretty long but I bought this because my couch and TV are really far apart, you probably won't need it.

You will need a keyboard to set up the controller for the first time, I borrowed my boyfriend's but I ordered this: Tripsky T9 2.4GHz Backlit Wireless Mini Keyboard, Handheld Remote with Touchpad Mouse for Android TV Box, Windows PC, HTPC, IPTV, Raspberry Pi, XBOX 360, PS3, PS4(Black) It is supposed to work with Pi but I'll have to get back to you when it gets here tomorrow.

I already had an HDMI cable but it's an Amazon Basics cable.

I was super pissed about not being able to get the SNES last week but this came out to around the same price for tons more games, plus Kodi. I don't think I'd be able to build it myself, so the card was awesome.

Power off by hitting quit on the main menu, then shut down. Wait until it's off (disconnected from TV screen) and unplug the power cord. Some people add buttons but this works just fine.

(When you load a game it says press any button to configure before it comes up, DO NOT PRRSS ANYTHING. It will do it on its own and start, you don't have to do any of that. I messed up and pressed it and didn't know how to get out.)

u/wilted_apostrophe · 4 pointsr/RetroPie

I ordered this case off of Amazon that came with a fan and a few heat sinks for about $11. However, you can also buy this fan for about $8.

This video helped me see exactly what GPIO pin the red wire needed to be connected to (the fan only takes up two pins).

Do you have a fan or AC vent you could set it next to for a more immediate fix? Good luck!

u/CBandicootRS · 5 pointsr/RetroPie

Kintaro SNES inspired Raspberry Pi Case - Super Kuma 9000 with functioning Power & Reset buttons, LED and Custom Aluminum Heatsink

This one is pretty cool, also the flirv case on Amazon is good for keeping the pi cooled without additional fans.

u/legacyblade · 2 pointsr/RetroPie

Yeah. Those tiny little heat sinks don't do much (since they're so small, they "fill up" with heat pretty quickly. And if you have no fan to dissipate that heat, they become useless at that point). They're more of a comfort blanket than anything. But for normal use, heat isn't an issue. (Even when overclocking).

If you ever get Kodi and notice the yellow square on screen, you might want to try a fan case. This is the one I'm using. It's pretty cheap, and the fan is pretty quiet (

u/Korruptor1 · 3 pointsr/RetroPie

I just built one today. The popular 2.5A power adapter is this one, which is probably on your list

Then I bought this case, which acts as a giant heat sink and was shown to cool the CPU more then the little heatsinks

I followed the instructions that others posted and I've been trying it out all night, with a few hiccups for certain systems (Neo Geo, Family Computer Disk System), but Google searches fixed those issues.

I'm using my Xbox One controller, which has been working great and has extra buttons for different things (like save states, which I don't think can be done an an SNES controller)

u/interfreak · 1 pointr/RetroPie

It's pretty easy to do. Don't be too concerned about damaging your Pi, it will simply not boot if you put some 'out there' figures in config.txt. If that happens, you can just pop the SD card back in your PC and delete out any lines you've added or change them.

As mentioned however, you'll need to make sure that your Pi has sufficient cooling to deal with the increased temperatures that are a side effect of overclocking. Personally, I use a Flirc Gen 2 case ( and it keeps temps at a reasonable level due to it's impressive passive cooling. I think ETA has done a review on this case as well.

edit here is the review -

I'm also very new to Retropie and have had a ball experimenting with various settings and building an image that it just right for me. :)

u/NBQ5 · 3 pointsr/RetroPie

Thanks! GBA games perform rather well actually as well as GBC games. I was playing oracle of seasons and it seemed to run great! I couldn't figure out how to use the original gameboy screen so I purchased and modded [this] ( screen to fit my needs. It only draws about 270-300mA so it's not too power hungry making it a fairly good choice for this project. Unfortunately the resolution is crap and reading the small text in the OS menus is difficult.

u/GuardianFerret · 1 pointr/RetroPie

Thank you for your reply. Based on what you've said, I think I will go with this 32GB Canakit here. I would like to see how well the Gamecube emulation works.

You seem to be experienced, so I hope you don't mind me asking a couple other questions real quick:

  1. How would I turn the Rasp Pi on and off if I am building an arcade cabinet enclosure to put it in? I know it can be powered off by accessing the menu with the controller - can it also be turned on with the controller?

  2. Does a sudden power failure have any detrimental impact on the device? (ex. if it was randomly unplugged prior to being shut down properly)

  3. What direction would you look for screens that I can plug into the Pi? I am looking for between 22-32 inches. Would the best bet to be buying a cheap TV of the right size that takes HDMI?

    Thanks for all your help!
u/chrono13 · 2 pointsr/RetroPie

Flirc case.

It looks nice, has very tight tolerances for sealing the case, comes with a thermal pad to connect the CPU to the entire aluminum block that is the case. One of the best passive cooling cases out there. Note that passive cooling still does not beat a fan, but it is often good enough.

Combined with the CanaKit which includes the excellent inline power switch.

Using one for a pihole, and one for a retropie.

u/ErantyInt · 9 pointsr/RetroPie

My favorite kit is this one:

CanaKit Raspberry Pi 3 Kit with Clear Case and 2.5A Power Supply

$50 for a $35 Pi3, an $8 case, a $10 PSU, plus some cheap aluminum Heatsinks.

This provides you with the bare minimum hardware, a good PSU, and a nice tool-free case, for cheaper than you could buy the individual components.

Add a good SD card (SanDisk or Samsung SDXC Class 10) and an HDMI cable, and you're in business.

u/realitybender · 5 pointsr/RetroPie
  1. if I remember correctly the SNES version doesn't shut down the fan when turned off. I like this case better


  2. I recommend 64 GB or more for MicroSD card, and don't cheap out ether, you need a good one for read and write speed.


  3. If you get a controller with analog sticks you can play most PS1 and N64 games
u/MiOdd · 3 pointsr/RetroPie

I just helped a friend of mine build his own, it's very easy to put together yourself. Here's our component list, that you may find helpful.

Raspberry Pi 3B

Flirc Raspberry Pi Case Gen2

8Bitdo Sn30 Bluetooth Gamepad

SanDisk 32GB Micro SD

AmazonBasics High-Speed HDMI Cable

NorthPada RPi3 Power Supply

Of course, there are many different cases and controllers you can use, you don't need to buy these specifically but it'll give you a good idea what you need to get started and what it will cost you when all is said and done. This is also assuming you just want something to play on TV. If you are a building a handheld, that's a different beast.

u/FlamingBagOfPoop · 6 pointsr/RetroPie

Looks like nespi by retroflag. Just got mine in yesterday. The power and reset button functionality is awesome. Though I’ve been reading I may need to link a python script to the reset button to be safer.

Retroflag NESPi Case+ Plus Functional POWER button with Safe Shutdown for Raspberry Pi 3 B+ (B Plus)

u/1thUponATime · 1 pointr/RetroPie

Thanks for the offer! I may just take you up on it. I decided to order THIS from Amazon with a 32gb MicroSD card the other day. Still have to get ROMs and do more research, but that is this evening and tomorrow before Easter Sunday. Will probably just use my PS4 controller for the time being, but I really would like to get a classic looking NES/SNES controller for the aesthetics. I really want the kids to have the same sort of experience I had.

Basically I am just looking for the classics, and your link to Racketboy looks real useful. I have seen a few rom packs out there with basically every NES and SNES game out there, but I am always worried about authenticity. I was reading one site earlier this morning and it mentioned that some of the bigger games like Zelda were in spanish, which is a problem. Looks like there is a lot of work to get all this done, so I may have a few questions.

u/Midgetforsale · 2 pointsr/RetroPie

I'm not sure about using a breadboard. Honestly, I use two zero delay usb encoder boards for my controls and it works perfectly. They came in the gamelec kit I bought, but you can buy them separately here - super simple to wire and just plugs into the usb on the pi. One note, if you have two sets of controls, make sure you wire the boards the same way. And by that I mean the same buttons to the same slots on each board. Otherwise, your controls will constantly seem to remap themselves.

u/dsotm75 · 1 pointr/RetroPie

CanaKit 5V 2.5A Raspberry Pi 3 Power Supply / Adapter / Charger (UL Listed)

Sorry for the delay in getting back to you, but this is the power adaptor I use. It works great with the case. If you are having a mating issue with the power port, check to make sure that the pi is sitting correctly in the case, and also make sure that the ends of the case line up and aren't pushed too far one way or the other.

u/Fdotg · 1 pointr/RetroPie

Power adapter I would say get the canakit for the rpi3b+

I have a case from wish that I spent 2 bucks on. So that’s totally up to you. If you plan to use it heavily I would say get some good fans and beat sinks

iUniker Raspberry Pi 3 B+ Dual Fan with Raspberry Pi Heatsink, Raspberry Pi Fan for Raspberry Pi 3B+/Pi 3 B/Pi 2 B

Then get a new memory card and download the Retropie image and flash it using something like applepibaker.


u/speeb · 19 pointsr/RetroPie

Like u/Jack_Bohlen said - the documentation is really good and you should be able to find answers to most of your questions. Being able to read and follow instructions carefully is important, especially if you get into doing anything from the command line.

If you can follow directions, you should have very few problems going from a box full of components to a basic working system in a short time.

Here are the instructions I gave a friend recently:

u/pickAside-startAwar · 7 pointsr/RetroPie

I love my old skool nes case for my retropie!! Hey, why don't you include a link to the product and maybe an image?! Show people how awesome this little case is.

Old Skool NES case for Raspberry Pi 3,2 and B+

u/Gamerdad09 · 1 pointr/RetroPie

I did this exact mod. I just used plain black electrical tape. Glad I did too as I had to open and recheck everything a few times after doing this mod and running into a few issues. The big one was the lighting bolt error caused by the cheap power wire. (The wires you cut to install the Pololu board between the rear USB micro port and the power button board.) You might consider replacing that whole section of +/- wires while you are in there.

I don't know how good it is, but there's also a brand new Nespi Case+ that is supposed to integrate safe shutdown with a script. I don't know if it's any better but here's a link. Hopefully we get some reviews soon.

u/ForgottenJoke · 2 pointsr/RetroPie

This is from a post I made on another thread like this:

Here is a list of the parts I used, from Amazon, to make an NES Mini.

Raspberry Pi


Power Supply


Micro SD

You would also need an HDMI cable if you don't have one already. Some people use wireless Bluetooth controllers, (the PI has Bluetooth and WiFi built in), but I don't know how well they work, latency wise.

Edit: For SNES and N64 you would need a more robust controller. You can use just about any USB controller that works with a PC, and a corded Xbox 360 controller works fine. I have heard others have used he WiiU Pro Controller, but I haven't tested that myself.

u/dt9779 · 3 pointsr/RetroPie

Yes it is possible, I don't have my pi with me currently but I have hundreds of NES, SNES, game gear, master system, and Genesis roms all saved on my micro SD card with the retropie setup. If you haven't bought your pi yet I would suggest buying the whole package off Amazon, it's what I did and it was helpful.
CanaKit Raspberry Pi 3 Complete Starter Kit - 32 GB Edition

u/red_rock · 10 pointsr/RetroPie

I have answers

  • You do, you can find finished models here. I actually have a 3D printer. But I found it hard to find the correct colored filaments, that´s why I bought the case instead.
  • Controllers can be found here. Just google "8Bitdo NES30 PRO" to find a local reseller.
  • I am using a Raspberry PI 3, with a 128gb SD card. Also added heatsinks on it.
  • To create one, I just downloaded this image (was by far the thing that took the longest, the actual download). I used this to copy the image over to the card (takes about an hour). Applied heat sinks on the Pi3 then screwed the Pi in to the case. I updated the firmware on the controller, then connected everything to my TV plus a keyboard. Once booted I expanded the file system, added the controller and wifi. Then I updated RetroPie. Once all of that was done I spend some time playing around with it, making changes as I saw fit. I also added new roms to it via my computer by just accessing it via the network (\\retropie). Once I was happy with everything I used the same tool to write to the SD card to create an Image from it, and backed that up to my computer. Then it just was a matter of putting the other ones together and then I just installed my image. Only thing I need to do is to expand the file system and adding the controllers. So 30 minutes building and configuring a Pie and 1h to write the image.
u/thenriques45 · 2 pointsr/RetroPie

I have the standard case that came with the CanaKit sold at Amazon (

I'm not very good at code or mod, but I found some guides and bought a small fan and made a script that control it. I fixed it at the case cover. When it is on it gets a little noisy for sure. Without a script it will be always on, but with the script it will turn on only when the Pi gets to certain temperature that you can set. As soon as it get below it, the fan turns off.

Works great for me!

This is the guide that I used to set the fan on the hardware side ( you will need a resistor for that. It's not hard tough. As I said, I'm a total noob and I actually did it.

The script that I use is this one (

One problem that I had is that the script, when started by crontab would not work properly for some reason. Solved by adding to the crontab a command to kill the script before it restart it. Can give you more details if you go trough this road.

u/JerkfaceJr777 · 3 pointsr/RetroPie

I think certain bundles are a good deal. The pi 3 bundle below is a good example- it comes w case, computer, and power. It’s cheaper to buy HDMI and SD card separately and you can get better controllers than the ones included in packages.

I’d use these bundles to get a sense of what you need to buy for the whole package and then buy those items a la carte.

u/-THEMACHOMAN- · 2 pointsr/RetroPie

Here's a 32 GB canakit package with case, power supply, HDMI, etc. Pretty much everything but the controllers. You save little by buying individually, and I've had good experiences with these (made about 12 thus far).

iBuffalo is the king of wired SNES controllers:

8Bitdo gear is the way to go for wireless, but if your recipients aren't tech savy, wired might be better:

I'd really stay awaay from controllers not made by those 2 brands. Everything else tends to be shit unless you're using an old Wii, Xbox, or PS controller.

u/Conterd22 · 1 pointr/RetroPie

Thank you, this Monday I bought this ( ) (sorry for formatting, I'm on my phone) thank you for the hope tho. Do you have a recommendation to a guide or anything like that?

u/lazd · 1 pointr/RetroPie

The FLIRC case is super clean, and it looks nice with one of these buttons installed in it as a soft power switch.

u/yallfrompurchasing · 34 pointsr/RetroPie

I recommend the Canakit.

For $70 everything is included. I put an RPie together last Christmas and instead of relying on the wife and family to find the parts as gifts, I just sent them to that link. Super easy, and it's been running non-stop all day since then.

u/jackster1232002 · 3 pointsr/RetroPie

> All i'm really looking for is something that I can plug in and play some old games on for a little while here and there.

You do realize it's not plug and play like the NES classic right? There's still some light software intallation involved with the Rpi. In fact it is illegal to sell/distribute a rpi with preloaded roms.

To answer your original post question, the price of the product is way to high for what you're getting. Taking 5 mins on amazon can get you much cheaper items especially with prime.

I still think this is too expensive, but it's still cheaper than the ebay link:

You just need to source your own controller which you can get here:

Best controller you can buy for $30. Which in total is still cheaper than the ebay kit.

u/Lordnerble · 2 pointsr/RetroPie

also depending on where you live and if you have amazon prime, you can get free 2 day shipping and it cost pretty much the same via amazon
thats where i got mine last week

u/OldSkoolTools · 2 pointsr/RetroPie

I happen to know a guy.

Good luck :)

u/rhinofinger · 22 pointsr/RetroPie

The RetroFlag NESPI+, Super Pi, and Mega Pi cases have safe shutdown circuitry and scripts, and are pretty popular here.

u/Triquick · 2 pointsr/RetroPie

If you don't want to deal with the noise of a fan the Flirc aluminum case is a amazing deal that really helps with overlocking. It fits over the raspberry pi CPU/GPU/RAM units and turns the whole case into a heat sink while providing a ton of protection to the Raspberry pi.

u/MaloCerebro · 2 pointsr/RetroPie

This is my bartop arcade that I built and I really happy how it came out.

I used the following parts from Amazon:

Raspberry Pi 3 Kit

Joystick and Buttons


I used 3/4'' MDF to build the structure and had a buddy who owns a print shop design and print the decals for me including the marquee. Most of the hardware used for electrical was bought at a local hardware store (Lowes, Home Depot, etc.)

Took about 15 hrs to build and was so much fun as is it to play with it. I mainly built it for my daughter which is just discovering retro gaming.

Maybe I will upload a video in action but everyone knows what it looks like and how it functions for the most part.

If there is anything you guys have a question about let me know in the comments.

Album not link?

u/clambert11 · 1 pointr/RetroPie

A really fun Raspberry Pi project. My goal was to keep as much of the soul of the Atari 2600 as possible. It was important to me to keep the mainboard in the unit. Unfortunately both the chips for the Television Adapter Interface and the CPU had to be removed so that the HDMI connector would fit. I mounted the chips inside the body to still be present.

It cost a little more to build it this way but I'm extremely happy with the result. My total came to just over $150, with the majority of the expense being the Raspberry Pi 3 and a 256 GB Micro SD Card. I guess I’m an idiot because I meant to buy a 3B+ but just now noticed I got only a model 3. Oh well.

There are 3 USB ports and 1 HDMI port extended. The power switch for the Pi was wired to Game Reset switch since it's a momentary switch. A wireless keyboard with touchpad is connected directly to the Pi.

I'm currently running the 256GB VIRTUALMAN-PLAYBOX! v2.0-4.4.11 RHODIUM RETRO-PARADISE image.

The stuff I bought to build this mod:

u/blackhecilopters · 1 pointr/RetroPie

That is a nice case, but as for the on/off switch I heard they pull down the amps. You need 2.5A for that sort of clock/performance.

I've got this one and it's been great so far.

u/PoorSpanaway · 1 pointr/RetroPie

Yeah, I think that building your own is the way to go. It's not really that hard to do if you can follow instructions and can write an image to a micro sd. I recently put one together and you can get away with spending around $100 for a great setup. This was my parts list:

SNES wired controllers x 2 ($16.00 ea):

The case ($27.99) :

Memory card 32 GB ($11.99):

Raspberry Pi 3 Model B ($34.81):

And then these optional luxury controllers - Wireless controllers x 2 ($47.16 ea):

u/alark · 1 pointr/RetroPie

Here are the files:

Here is the part list, the bone cost ~$100, just fyi. Here are my notes and the parts list:
Battery: $20
Raspberry Pi:$30
The power boost didn't work, the setup drew too much current, and I had to buy the 1000c. The case is build for the 500c, so I had to file the powerboost chip down a tiny bit to get it to fit. Make sure wires coming from powerboost can handle ~1A, I suggest 20-22 gauge wires.
Also, I use a volume control knob to help my volume situation:
And small ~1 inch speakers:
The LCD screen works, but you have to remove the top left voltage transformation chip and tap into the 3rd pin to get the 5 V to the rest of the screen. Also, I bought a cheaper version of the same screen.

u/PRG013 · 4 pointsr/RetroPie

Overpriced. He built that using a $5 Pi Zero.

Personally, I bought this:
It's about 10x more powerful and can play many more types of games. Has Bult-in WiFi and Ethernet.

Download RetroPie disk image from the official site.
There are a ton of videos out there to help you set it up.

I use my Xbox 360 Controllers.

u/hiccup50073 · 1 pointr/RetroPie

doesn't really matter. just make sure it has:

-2 heat sinks (just look on youtube how to install them. a toddler could do it)

-the circuit board

-the case- the standard cases are a bit boring so you might want to skip that and buy some awesome custom nes case like this

Anything else you need you can buy at walmart

u/phertiker · 3 pointsr/RetroPie

Here's one that looks like a mini-NES. It's good quality, though kind of pricey at $20-ish.
The only thing I don't like are the HDMI/power ports are on the side, USB/Ethernet under the NES cart flap, and no access to GPIO without modification. Those are minor things, though, and the "That's dope" factor is high.
I paired it with this bluetooth gamepad which is surprisingly good.

u/sardu1 · 1 pointr/RetroPie

I've found that one of the best cheap clone is the SNES controller made by Buffalo. There are others but I'm satisfied with it.

u/CrapInc · 2 pointsr/RetroPie

raspberry pi 3: $33.53

power supply: $7.99

case: $19.99

32GB SD Card w/ adapter: $12.31

2pk SNES USB iNNEXT Controllers: $16.99

So that's $90.81 before tax and shipping. Plus no choice in custom color of top and bottom of case, having to put it together yourself, download an image and configure it. So for a non-technical person it might be worth it since they'd be paying an extra $15 - $20 in this case for the labor/time involved.

(and yes, those controllers are garbage, but at least they can get replacements easily after the fact)

u/Broman_907 · 12 pointsr/RetroPie

Same here. Tried to be honest but Nintendo shipping 10 total minis to each store in Anchorage (insanity) pushed me over the edge. Amazon. Do it. that's the one I ordered. Complete kit. Join the resistance

u/omgwtfnon · 3 pointsr/RetroPie

I've chosen the Flirc case, looks nice and does a good job with cooling compared to heat sinks. Haven't had the chance of testing it out myself, I need to wait for it to arrive. My source was youtube, so you can check that out if you want.

u/zer0guy · 2 pointsr/RetroPie

buy this kit for $50

it includes the chip, case, and power.
the main thing you will need besides that is a microSD I'd recommend at least a 64gb. so that's about $22.
if you have a HDMI cable, and ps3 controller laying around, your pretty much done. so about $75 total.

u/Steven_Q_Glansberg · 1 pointr/RetroPie

Yes, it's the CanaKit here:

The tape was already on the sinks. Black in color, if that helps?

Correct, nothing tweaked as in software or settings. It's running all on default settings.

u/DMPSTRFR · 2 pointsr/RetroPie

$45 MicroSD card, sold by Samsung through Amazon. The odds of this card being "fake" are slim enough that I'd wager real money. Sandisk sells the same thing for the same price.

Definitely beware of $20 128GB cards, but $40 could be achievable, especially during a sale.

Edit: Link

u/StopPlopAndRoll · 1 pointr/RetroPie

I used this one. It's cheap and it works but you need to solder it so it can run on 5v.

The screens inside aren't all the same so if you check over at there is a thread in the forums showing where people have soldered them based on the different guts. Hope this helps!

u/knowreason · 1 pointr/RetroPie

I use a couple of the Buffalo USB controllers. They feel, look, and work great.

u/samus12345 · 1 pointr/RetroPie

I had great results with this. The only other thing you need is a controller and keyboard.

u/theWinterDojer · 2 pointsr/RetroPie

If you're just using SNES get these, they're awesome.

u/-_galaxy_- · 2 pointsr/RetroPie

Just about any SNES USB controller will work well. The Buffalo ones are better than generic Chinese ones and they're 12 bucks :

u/grem75 · 1 pointr/RetroPie

It can be made to work with RetroPie, but you'll only get about 15fps out of it with that resolution. The 320x240 resolution screens are a bit better, but still nowhere near 60fps.

Right now the only option in that size with a decent frame rate is a composite screen. A lot of people use these.

u/muhaski · 25 pointsr/RetroPie

I'd go with a Canakit, but not the complete one. This version is only the case, Pi, and power cable for $50. Your complete starter kit comes with a generic SD card and HDMI cable for an extra $20 which you can get better versions of for around the same price or cheaper (or you have an HDMI cable laying around).

u/SausageKingOfKansas · 1 pointr/RetroPie

It's the v3 starter kit purchased on Amazon:

The image is retropie-4.4-rpi2_rpi3.img

I did initially set everything up with the keyboard.

I did just start it up for the first time in months. I have two of the Buffalo USB controllers. One doesn't appear to work at all and I tried multiple USB ports. The other seems to work for navigating around RetroPie but once I get into a game nothing works.

Any ideas? Thank you for the help. I was so excited about this when I first set it up and it's mostly been a disappointment because I can't get the damn thing working.

u/tsoliman · 4 pointsr/RetroPie

I looked it up, it's "Vilros" not "Viros" apparently. No clue if it works and never heard of it before.

For that price you should get the flirc case instead. Kind of a famous case that's proven to work.

u/exobuzz · 3 pointsr/RetroPie

>To remove hiss or static or white noise when using the 3.5mm headphone jack:

> Run at the command line: sudo nano /boot/config.txt and insert at the bottom of the file: disable_audio_dither=1
turn up Retropie volume to 100% in the settings menu in the program.
> get an inline volume control:
Another option is to set audio_pwm_mode=2 in the same config - this is a new audio driver that should significantly improve the sound quality - see

with disable_audio_dither=1 or audio_pwm_mode=2 audio is fine here.

u/ICanHearYouClearly · 1 pointr/RetroPie

As others have mentioned, a micro SD and an adapter are necessary as well. I'd also recommend this power supply for guaranteed 2.5A, though the one you already have may be very similar:

What I haven't seen anybody note, though, is that Buffalo offers newer controllers that also happen to be cheaper:

u/shadowstitch · 2 pointsr/RetroPie

It's just Amazon defaulting the price to the first person who has them in stock at this moment.
Give the original 3rd party seller time to restock and the price will drop back to 20.

u/epichuntarz · 1 pointr/RetroPie

Just a note in regards to the controllers-try this one:

The controller model ending in 815 seems to be all they ship now. Yours is the 801 and currently at 18.88, but you will receive the EXACT same controller as if you ordered the 815 version above (there's also another listing for them), and they're 16.48. Just an FYI!

u/Feanor23 · 24 pointsr/RetroPie

That is exactly what got me here... can someone confirm this as a decent option? For now I just want to do older sims up to SNES, I realize I would probably need an upgrade for PSX/N64/Wii.

How about a good controller option?

u/Jon76 · 1 pointr/RetroPie

Alright, here is how to install RetroPie (to play classic games)

For the raspberry pi, get this set and a class 10 micro SD card.

u/davidmt · 1 pointr/RetroPie

Yes, that is exactly what I have. It is the one that comes with the Canakits that I got from Amazon.

u/ruppdogg78 · 1 pointr/RetroPie

I got the canakit, a Bluetooth controller, and 32gb micro sd. Around $70 give or take.

CanaKit Raspberry Pi 3 Kit with Clear Case and 2.5A Power Supply

Matricom G-Pad BX Wireless USB Rechargeable Bluetooth Pro Game Pad Joystick (Samsung...

Samsung EVO 32GB Class 10 Micro SDHC Card with Adapter (MB-MP32DA/AM)

u/viverx · 2 pointsr/RetroPie

Do you have a Sd card reader ?

Buying this kit will get you the same power Adapter and Pi for 2 dollar cheaper and some free heatsinks

u/ab2650 · 4 pointsr/RetroPie

That's pretty close. I just did a build, so here's some recent prices:

Pi 3 with 5v 2.5A power supply and heat sinks - Was $49.99, now $46.99
32GB MicroSD - Was $9.99, now $11.99
This plain case, which I put custom stickers on - $6.99
Two SNES-style USB gamepads - $12.20 each

I didn't include an HDMI cable because I had several laying around, so your minimum cost is about accurate.

Edit: Oh, and this case to keep it organized while traveling.

u/3wooki3 · 1 pointr/RetroPie

Cases are like $12 on Amazon. You can't afford that?


That was $12 a month ago when I bought 2 of them. Now they're $16. I put a pi 1B in one of them.

u/mellow65 · 2 pointsr/RetroPie

I don't have any experience with those so I can't comment one way or another.

Do you have any other controllers that you can try? Or do you know anyone else with a pi you can try your controller on?

This is what I got
Buffalo Classic USB Gamepad for PC

And it works great. The lag, if there is any, is so microscopic that I can't even tell.