Best products from r/prusa
We found 10 comments on r/prusa discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 9 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Genuine E3D V6 Extra Nozzle - 1.75mm x 0.40mm (V6-NOZZLE-175-400)
- Genuine E3D V6 replacement nozzle for 1.75mm filament at .4mm nozzle size.
- This premium quality E3D replacement nozzle allows you to truly customize each and every print.
- This high quality nozzle have been created using community feedback and notes over multiple revisions from E3D
Features:
2. Liquid Bearings, SUPERIOR 100%-synthetic oil for lubrication of drones, RC vehicles and equipment
- 100%-synthetic lubricant, perfect for all typewriters
- Immediately begins to displace old petro-oils or sprays.
- Excellent corrosion prevention for any metal surfaces.
- Essentially odor-free, a pleasure to use!
- Includes both 1/2" AND 1-1/2" needles, each with tip scabbard!
Features:
3. Gizmo Dorks Kapton Tape (Polyimide) for 3D Printers and Printing, 9 Inches x 100 Feet
- Superior quality Kapton polyimide tape for 3D printing
- Resistant to high temperatures making it perfect for plastic filaments requiring heated build beds such as ABS
- 3D prints adhere very well especially under high heat but release cleanly when cooled
- Great durability for multiple print cycles without needing to change the tape
- Long lasting tape roll that is 9 inches wide by 100 feet long
Features:
4. AMX3d Pro Grade 3D Printer Tool Kit - All The 3D Printing Tools & Accessories Needed to Remove, Clean & Finish 3D Prints (Pro Grade)
- THE ESSENTIAL TOOLS FOR 3D PRINTING: Our Pro Grade Tool kit has everything needed to remove, clean & finish 3D printed models in one convenient toolkit. Selected for function and quality, these tools were selected, designed, assembled and are supported by AMX3d in Lisle, Illinois. These high quality, Professional Grade tools are the essential addition to any 3D printing system.
- EASY CLEANING: Clean and finish your 3D prints - so they look like the pro prints on the 3D Printer Box!
- SIMPLE REMOVAL: Get your 3D prints off the print bed without damaging either! Slide one of the 3 removal tools under your print and lift (don’t pry) your prints away.
- PERFECT FINISH: The 3 piece / 6 Tool precision scraper / pick / knife blade combo tools get into the smallest crevices to perfectly finish your print.
- QUALITY: The Best Prints Start With The Best Tools! Choose either the Pro Grade or the Pro Grade PLUS. AMX3d provides 3D printing supplies of the highest quality.
Features:
5. SIQUK 33 Pcs 3D Printer Nozzle Cleaning Kit 30 Pcs 0.15mm, 0.25mm, 0.35mm, 0.4mm, 0.5mm Cleaning Needles 2 Pcs Tweezers and 1 Pc Cleaning Cloth
- Fine sizes assorted - 0.15 mm, 0.25 mm, 0.35mm, 0.4 mm and 0.5 mm cleaning needles not only suitable for most of sizes nozzle but also they can use for cleaning other small parts, such as throat and feeder gear
- Premium material - SIQUK 3D printer nozzle cleaners are made of premium stainless steel material, sturdy, durable and flexible, easy to twist
- Wide compatibility - compatible with most of 3D printers extruder nozzles offered from E3D Makerbot, MK8 Makerbot RepRap
- Free gift - come with 2 different shape precision tweezers and 1 piece cleaning cloth, help you cleaning excess filament gear material and keep nozzles clean
- Package include - there are 30 pieces 3D printer nozzle cleaning needles in 5 different size, 2 pieces different sharpe precision tweezers and 1 piece cleaning cloth, totally 33 pieces nozzle cleaning kit
Features:
6. Prusament Prusa Galaxy Black, PLA Filament 1.75mm 1kg Spool (2.2 lbs), Diameter Tolerance +/- 0.02mm
- Manufactured in-house by Prusa Polymers - We were not satisfied with the quality of filaments on the market. So we decided to make our own. As a part of Prusa Research companies group, we are the only 3D printer manufacturer with its own filament production.
- Premium-grade materials and thorough testing - The whole manufacturing process is closely monitored and tested – string diameter, color consistency, and mechanical properties – to make sure that every spool is perfect.
- High Quality you can check yourself - We are the only manufacturer that gives customers the option to fully inspect parameters of every filament spool. Just scan a QR code on the spool to see all details online.
- 0. 02 mm Manufacturing Precision - We believe the industry standard of 0. 05 mm isn’t sufficient for perfect 3D printing. Instead, we 0. 02mm precision and highly-consistent colors in our filaments.
- Prusa Galaxy Black is inspired by the frame of our Original Prusa i3 printers.
Features:
7. Thekkiinngg Prusa MK3 /S Double-Sided Textured Pei Powder-Coated Sheet V4
Made of high strength spring steel sheet Made of steel from U.S.A. with Pei Powder coat . We guarantee that this Bed plate contains Ultem PEI .Special coating that helps your pieces to adhere better than any other plates on market .Easy to separate the plastic parts when cooling.Rough finish of bott...
8. FYSETC 3Pcs Upgrade HT-NTC100K Thermistor 3D Printer Parts Thermistor Sensor High Temperature +300 Degrees for Reprap CR10 Ender Anet A8 Monoprice Maker Pro Hot End Heater Block
- Upgrade HT-NTC100K 3950 Thermistor: Pack of 3Pcs. Note: Temperature measurement head cylinder diameter is 3mm, length 15mm, The connector is 2pin XH2.54, so make sure your heater block is the right hole, the board Connection terminal is the right type, can be used with the heating block that support the thermocouple.
- The temperature measurement: -20 °C ~ +250 °C for a longer lifecycle, sometimes can reach +300℃(but not recommand to use it long time)can replace the original K-type thermocouple temperature, very fit for printing high-temperature filament.
- Adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. If need a longer one, please search our 2m thermistor (Asin:B09WMRW8HC).
- HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off.
- Not fit for CR-6 SE heater block.
Features:
9. CyberPower CP1000AVRLCD Intelligent LCD UPS System, 1000VA/600W, 9 Outlets, AVR, Mini-Tower
- 1000VA/600W Intelligent LCD Battery Backup Uninterruptible Power Supply (UPS) System uses simulated sine wave output to safeguard workstations, networking devices, and home entertainment equipment
- NINE NEMA 5-15R OUTLETS: Five battery backup & surge protected outlets; Four surge protected outlets; INPUT: NEMA 5-15P right angle, 45 degree offset plug with six foot power cord
- MULTIFUNCTION LCD PANEL: Displays immediate, detailed information on battery and power conditions, including: estimated runtime, battery capacity, load capacity, etc
- AUTOMATIC VOLTAGE REGULATION (AVR): Corrects minor power fluctuations without switching to battery power, thereby extending the life of the battery
- 3-YEAR WARRANTY – INCLUDING THE BATTERY; dollars350,000 Connected Equipment Guarantee and FREE PowerPanel Personal Edition Management Software (Download)
Features:
Hm, so some quick stuff. The pi zero is kinda slow, i would not recommend it tbh. i got the regular pi 3 and it works pretty well. if you want timelapses and stuff (octolapse) then it's a must
they do have prints on thingiverse for the regular pi, you can still mount it on the printer. shouldnt matter what material, you just want to make sure it doesnt hit the printer head/heatbed (or any moving parts) and ensure it can get somewhat airflow.
https://www.thingiverse.com/search?q=pi+prusa&dwh=485d4388e714606
PLA is the easiest, start with that and you can try others (abs/flex/etc) later. get used to printing. prusament is really nice stuff but a tad more pricey. amazon has a few colors in stock
https://www.amazon.com/Prusament-Galaxy-Filament-Diameter-Tolerance/dp/B07M8GWZBS/
other brands i like, hatchbox, paramount, matterhackers, just look at the reviews and see what people say
noob kit, hm, these are kinda nice, few useful tools
https://www.amazon.com/40-Piece-Printer-Tool-Kit/dp/B07BM8C6SS/
needles to help clean clogged nozzles (though it doesnt happen often)
https://www.amazon.com/Printer-Cleaning-including-Cleaner-Needles/dp/B07G493V8M/
liquid bearing for the steel rods should help, need to oil them up ever few months or when its dry
https://www.amazon.com/Liquid-Bearings-100-synthetic-lubrication-equipment/dp/B016YSLMXA/
i ilke kapton tape to hold parts to the heatbed better but you dont need it
https://www.amazon.com/Gizmo-Dorks-Polyimide-Printers-Printing/dp/B01FECA0E4
extra nozzle is always good (ive bought this brand but others SHOULD work, your results may vary)
https://www.amazon.com/Genuine-E3D-Extra-Nozzle-V6-NOZZLE-175-400/dp/B00NAK9TWM/
extra ptfe tube is nice too, i got some on ebay (a few feet for my mmu2)
blender is nice since it's free, i used 3d max myself but its expensive
ive printed a lot haha, my stuff is here https://www.instagram.com/dude2k5/
Makes sense on the case. I am using a regular pi 3 for mine. I heard that the Zero can't quite keep up anyway. Is that still the case?
Here is the sheet that I ordered. It was Amazon, not eBay, but I think it's the same seller.
https://www.amazon.com/gp/product/B07HQZCWDV/ref=ppx_od_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
I like it much more than the smooth PEI sheet, because I don't have to worry about PETG sticking to it too strong (or putting glue down). I've ruined a few smooth PEI sheets because I forgot to put glue down before printing. No such problems with the textured, and the finish looks really cool. But I also agree that it's good have the smooth when you need it.
Not sure of the one you're are looking at, but I broke mine about 6 months ago and successfully replaced with this https://www.amazon.com/Upgrade-HT-NTC100K-Thermistor-FYSETC-Temperature/dp/B07D9LSKWK/
I have one of these and haven't seen any issues yet.