Best products from r/s10
We found 21 comments on r/s10 discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 23 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. 4x6 LED Rectangular Headlight Projector Lens Sealed Beam Replacement CREE HID Xenon Headlamp Bulb H4651 H4652 H4656 H4666 H6545 for 86-95 JEEP WRANGLER Peterbilt Kenworth FREIGHTLINER (4x6)
- SUNPIE 4" x 6" Headlight Compatibility: H4651 H4652 H4656 H4666 H6545. Can be used as low beam or high beam. Pins on plug may need to be moved on some vehicles. You may need to adjust the PINS - Toyota vehicles use different Ground/Low/High beam positions on the pins.
- Come in applications that fit up to 95% of vehicles, including sedans, light SUVs and trucks, motorcycles, and off-road vehicles. Some vehicles such as : Dodge Challenger,Dodge Charger, Dodge Dart, Chevelle, Corvette, Nova,Ford Galaxie,Oldsmobile Cutlas,Pontiac GTO,Plymouth Barracuda,Plymouth Road Runner Can be used as low beam or high beam.
- Plug: H4; Power: 45W (15 Ultra Bright 3W LED Chips); Effective Luminous Flux: 4200LM@high beam,2500LM@low beam; Waterproof Rate: IP68; Dimension:6.7(length) x 4.33 (width)x 3.15 inch(depth)
- Notice! You can buy up to 4 if you want to change low and high beam. Remember! These fit vehicles that have 4 headlamps. Sold individually.
- 45W LED create the perfect light for your vehicle with sealed beam light system. Better and more durable than HID kits. Simply change your headlight out.
Features:
2. OBD2 Scanner CAN OBDII Code Reader - Scan Tool for Check Engine Light - Universal Diagnostic for Car, SUV, Truck and Van (MS300)
SMALL SIZE: Measuring 2.75”L x 4”W x 24”H and weighing in at 8 ounces, the OBDII scan tool will comfortably fit in the palm of your hand.COMPATIBILITY: Works with most 1996 & newer US-based vehicles that are OBDII compliant (including CAN) and supports all OBDII protocols.EASY TO USE: Once plu...
3. TADD Replacement for Chevrolet S10 / S15 & GMC Sonoma Rear Driveshaft 1994-2003 2 Weel Drive 4.3 Liter Automatic Transmission
- Extended Cab Problem Solving CV Eliminator
- This NEW Driveshaft is complete, balanced and ready to install using your front section over.
- Dynamically high speed balanced for vibration-free operation
- Measures 46 3/4" from the face of the flange at rear end to end of the slip yoke that slides on to the splines near the center support bearing
- Includes slip yoke and rear flange
Features:
4. CREACLE V2.1 Super MINI ELM327 Bluetooth OBD/OBD2 ELM 327 Multi-Language 12Kinds Works ON Android Torque/PC
1.The Smallest Size ELM 327 SUPER MINI Bluetooth2.Woks on Android Torque/PC(only windows XP and close anti-virus programm),no work IOS!3.Bluetooth Password: 0000/1234/67894.Latest Software Version V2.15. Supports Multi-Language 12kinds:
5. Monroe 58523 Monroe Load Adjust Shock Absorber
All Weather Fluid: Contains special modifiers to reduce friction and ensure smooth rod reactionFull Displaced Valving: Tuned specifically for each application, this valving automatically adjusts to road extremes to provide consistency and rideFluon Banded Piston: The fluon band provides consistent s...
6. Steck Manufacturing 21910 Car and Light Truck Door Spring Tool
Compresses spring for easy, safe removalSides safely enclose springHeat-treated, high carbon steelThe safest tool available for coil springs in GM doors
7. Red Hound Auto Door Hinge Pin Single Kit 4 Pin 2 Door fits 1995-2004 Compatible with Chevy GMC S10 S15 Premium
Door Hinge Pin and Bushing KitReference Numbers: 38419, 15562609, 15653790, 15691494, 15964971, 15964972, 16632192, 16632193, 25640501, 88891731, 93356553.Heavy Duty Steel.(4) Steel Door Hinge Pin, (8) Bushings and (4) Retaining Clip.
8. ACDelco 213-70 GM Original Equipment Engine Coolant Temperature Sensor
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Features:
9. ACDelco 213-928 GM Original Equipment Multi-Purpose Temperature Sensor
- Helps keep engine operating at proper temperature
- Sends accurate temperature readings to the gauge
- GM recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Features:
10. ACDelco MU1733 GM Original Equipment Fuel Pump and Level Sensor Module with Seal, Float, and Harness
- Helps deliver a reliable supply of fuel to the engine
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Features:
11. uxcell 2 x DC 12V H4 9003 Ceramic Wire Headlight Harness Sockets for Car Headlight
- New
- Mint Condition
- Dispatch same day for order received before 12 noon
- Guaranteed packaging
- No quibbles returns
Features:
12. 4x4 Posi-Lok PSL500 Axle Disconnect
- package dimensions :7.31 " L x 6.25 " W x 4.89 " H
- Product type :AUTO PART
- Package Weight: 2.8 lbs
- country of origin : China
Features:
13. Dorman 82560 Oil Adapter and Cooler Gasket Assortment, 15 Piece
Dorman82560Components
14. Steadfast Auto 10203 Chevrolet Compatible Fixed Mast Antenna 8 Inch Black, Replacement For Chevrolet S-10
- Manufactured for superior structural strength
- Best radio reception for antenna of this size
- High-Grade Stainless Steel mounting hardware
- Threaded shaft ends will not come apart like press ons
- Full 1 Year Warranty against defect in the product or workmanship of the product
Features:
15. Street Scene 950-11210 Style 1 CAL-VU Sport Mirror
- Tough abs materials
- Aerodynamic styling
- Convex passenger side glass
- Modular construction
- Custom paintable
Features:
16. UAC CO 20145C A/C Compressor
Brand New, OE replacement: UAC branded HT6 Compressor Assembly100% Guaranteed Fit! Add your car (year/make/model) to Amazon's garage to confirmPremium ISO/TS 16949 quality; tested to meet or exceed OEM specificationsIncludes: body, clutch, pulley & coil; compressor may come charged with shipping oil...
17. Lantee Car Clips for GM - 50 Front Door Trim Panel Retainers Clips Replaces for GM 10153057
Lantee White Nylon Front Door Trim Panel RetainerTop Head Diameter: 18mmBottom Head Diameter: 20mmStem Diameter: 8mm; Stem Length: 23mmReplaces for General Motors 10153057 1982 - On
18. 180 PCS Wirefy Heat Shrink Butt Connectors - Crimp Connector Kit - Electrical Wire Terminals - Waterproof Butt Splices
WATERPROOF - Butt connectors with heat activated adhesive protect against corrosion and vibrationSUPER STRONG CRIMPS - Crimp connectors have thick copper barrels to tightly grip any wiresMAX CURRENT FLOW - Heat shrink butt connectors use tinned copper barrels for highest conductivityEASY TO SHRINK -...
19. Dorman 600-500 Transfer Case Switch for Select Chevrolet / GMC / Oldsmobile Models
- Direct replacement - this 4WD switch matches the fit and function of the original switch on specific vehicle applications
- Effective fix - restores proper 4WD operation after original switch degrades and fails
- Durable construction - built for reliable longevity, free of defects in materials and craftmanship
- Trustworthy quality - backed by team of designers and engineers in the United States
- Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool
Features:
20. Delphi FS0177 Fuel Strainer
- Delphi brings 80 + years of OE Heritage into each Delphi strainer, ensuring quality and fitment for each Delphi part.
- Filtration performance and micron rating meet or exceed OE requirements
- Replacing the strainer is always recommended when replacing a fuel pump
- Strainer uses saran strainer material to ensure filtration performance
- OE replacement strainer designed for use with Delphi electric fuel pumps
Features:
Your best bet is to get a code reader, if you don't already have one. Here is a cheap one on Amazon. Failing that, your nearest VIP or other auto shop will usually read the code for you for free.
Once you know the diagnostic code it's throwing, you'll have a better idea what happened.
I'm leaning toward it not being a frozen anything; if something froze in the injectors, you have a lot of water in your gas, which would cause problems even when it's not cold out.
Very often rough idle is caused by MAF and O2 sensors. You also might be having issues in the ignition system, so check your plugs, wires, and distributor.
Good luck, and please come back to post more question, or if you found the solution, post that.
I have a 96 ext cab 4.3v6 Auto that came with the two piece and double cardan. I was experiencing horrible noise and vibration and ended up replacing the carrier bearing and the double cardan half of the shaft with this unit from Amazon.
​
I've had it in there for over a year on a truck that's lowered 4" all around(pinion angle corrected). It's been on a few road trips totaling over a 1,000 miles and has seen plenty of runs up to the speed governor(95mph), sometimes holding 90mph+ for many miles.
​
My personal experience with it has been really great. I have no basis to a good stock unit but it was a dramatic improvement over the one I had in it. Vibrations and noise virtually zero and there seemed to be a difference in throttle response as well.
​
This was a direct bolt in and go. I changed it out over a couple hours in the driveway with some help.
​
If this place still insists on that price I would suggest replacing it yourself either with the unit I linked or a stock replacement.
What year truck do you have? I used these on my 95. You have to do some wiring on your own but it illuminates the road way more than the stock halogens. These fit right in to the sqaure perfectly.
​
https://www.amazon.com/gp/product/B01DEXAOUK/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
I have owned 3 2.2s. They tend to run cold because they don't produce a ton of heat like larger displacement engines. If it's cold out it runs cold. If it is hot out and the mechanical fan is stuck on it runs normal temps. Also the dash gauge is not as accurate as the ECU temp readouts.
My guess is that you live in a cold environment and your mechanical thermostat is broken or old enough that it doesn't work right.
I currently have a built 2.2 turbo. When it is cold out, the gauge will read 150-185 when it is 30 or lower to 60 degrees. That is cruising on the highway at 50-70. Now I also use HPtuners to tune. I monitor my temps. Typically the loop from the heater core to the block will be within 180 to 195 where it is supposed to be.
My recommendations.
[obd2 to bluetooth adapter] (http://www.amazon.com/gp/product/B00N2K6M2A/ref=pd_lpo_sbs_dp_ss_2?pf_rd_p=1944687642&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B0051CAE1C&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=0T816CFEDTS905VMXVPW) - I own this one. It works.
GLHF
https://www.amazon.com/Monroe-58523-Adjust-Shock-Absorber/dp/B000C59ME
​
These will stiffen up the rear a good deal. they replace your shocks as well, easy change out.
This is the 1 pin. It is for the gauge, and does not need to be changed. It's on the cylinder head
https://www.amazon.com/ACDelco-213-70-Original-Equipment-Temperature/dp/B000C9GRDI
This is the 2 pin, it's on the intake manifold near the thermostat, and this tell your ECM the temperature
https://www.amazon.com/ACDelco-213-928-Equipment-Multi-Purpose-Temperature/dp/B000C9I038
Of course you don't need the AC Delco brand parts, but it's the numbers i got from the factory parts diagrams from YOUR SPECIFIC TRUCK just to be absolutely sure.
I ordered mine from ACDelco.. On Amazon about a week ago ACDelco MU1733 GM Original Equipment Fuel Pump and Level Sensor Module with Seal, Float, and Harness https://www.amazon.com/dp/B001S2TPVE/ref=cm_sw_r_cp_apa_i_F.mPDbCJYV6C2
This. I recommend deleting this component and replace it with a posi-lok cable. Plug the vacuum line with a bolt. Then order and install 4x4 Posi-Lok PSL500 Axle Disconnect. https://www.amazon.com/4x4-Posi-Lok-PSL500-Axle-Disconnect/dp/B004TOLFMU Here's mine installed. It will work for all s10s. https://i.imgur.com/L0m7eQu.jpg
Street Scene 950-11210 Style 1 CAL-VU Sport Mirror https://www.amazon.com/dp/B000BRA6R4/ref=cm_sw_r_cp_apa_lGTlzbTR4TA9Z
Steadfast Auto 10203 - Chevrolet S-10 Antenna 8 Inch - Black https://www.amazon.com/dp/B00VW0JQ9I/ref=cm_sw_r_cp_apa_LHTlzbEVNN0ET
Are you these the ones? door panel clips
Quick and easy, for sure. Unfortunately they don’t really seal and are notorious for causing wire corrosion. As an alternative, I’d suggest considering these instead. A little extra work, but they’re much more reliable when properly installed.
Well that stupid bulb is an expensive fuck for how delicate it is. I tried a cheaper ($40) one and it didn't work once, it tried to actuate and the plate that's supposed to do the pulling just went C-shaped. The decent ones cost about $80, but I haven't tried any of them. There's a kit to convert it to a pull-cable setup where you push the button to get the t-case to select gear, and then pullcable engage the diff yourself. Or you can get one of these guys and rig it up yourself somehow.
I'm not entirely up to speed on how the whole system works but the bulb is a common point of failure, or the switch that sits on the t-case itself. Which is this guy. If that fails, it'll suck ATF into the vacuum system that controls the front diff engagement, which can tear up the bulb.
Here's a good post that has some more info on the 4WD system, and also a possible mystery vacuum hose you may or may not have loose.