Reddit mentions: The best rc engine bearings
We found 12 Reddit comments discussing the best rc engine bearings. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 10 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Tamiya TT-01 Chassis Sealed Bearing Kit
- ✅ Join the thousands of expert racers drivers and bashers that have been trusting FastEddy Bearings for over 15 years. Engineered by our Pro R/C Racing Team you are not only getting the highest quality bearings for the lowest price but the top brand in the industry.
- ✅ FastEddy Bearing Kits include all the bearings to upgrade your R/C to peak performance. Experience faster longer and smoother runtimes with peak performance.
- ✅ Trusted High Quality Chromium Steel 52100 (GCr15) Precision Races and Balls are used for the construction to ensure longevity and the highest possible quality available.
- ✅ Our proprietary high heat low drag synthetic lubrication formula that will last the life of the bearing allowing you to reach top speeds for extended periods of time.
- ✅ Low drag minimum contact rubber seals will keep contamination out and extend the life of your bearings.
Features:
Specs:
Weight | 0.0125 Pounds |
2. Traxxas 5116 5x11x4mm Replacement Precision Ball Bearings MR115-2RSBU (10)
- Inner Dia 5mm Outer Dia 11mm Width 4mm, ID = 5mm OD = 11mm Width = 4mm
- Compatible with Axial: AXA1221 Arrma: AR610019 Losi: LOSA6947 HPI: B022
- Compatible with Tamiya: 58041, 58354, 58056 Compatible with Traxxas: 4611, 5116 Team Associated: 25239, 25618
- Lubricated with Grease, Chrome Steel 52100 (GCr15) ABEC 3 Precision Races, Hard Chrome Steel 52100 (GCr15) Balls
Features:
Specs:
Height | 0.59 Inches |
Length | 4.21 Inches |
Number of items | 10 |
Weight | 0.01 Pounds |
Width | 4.02 Inches |
3. 5x13x4mm Precision Ball Bearings ABEC 3 Rubber Seals (10) 695-2RS-BU
- Compatible with: Losi: LOSA6955, HPI: B018
Features:
Specs:
Height | 0.8 Inches |
Length | 3.5 Inches |
Number of items | 10 |
Weight | 0.01 Pounds |
Width | 2.3 Inches |
4. Tamiya Subaru BRZ R&D Sport 2014 Fuji (TT-02) Sealed Bearing Kit
- ✅ Join the thousands of expert racers drivers and bashers that have been trusting FastEddy Bearings for over 15 years. Engineered by our Pro R/C Racing Team you are not only getting the highest quality bearings for the lowest price but the top brand in the industry.
- ✅ FastEddy Bearing Kits include all the bearings to upgrade your R/C to peak performance. Experience faster longer and smoother runtimes with peak performance.
- ✅ Trusted High Quality Chromium Steel 52100 (GCr15) Precision Races and Balls are used for the construction to ensure longevity and the highest possible quality available.
- ✅ Our proprietary high heat low drag synthetic lubrication formula that will last the life of the bearing allowing you to reach top speeds for extended periods of time.
- ✅ Low drag minimum contact rubber seals will keep contamination out and extend the life of your bearings.
Features:
Specs:
Weight | 0.0125 Pounds |
5. Traxxas 1/16th Mini E-Revo Sealed Bearing Kit
- ✅ Join the thousands of expert racers drivers and bashers that have been trusting FastEddy Bearings for over 15 years. Engineered by our Pro R/C Racing Team you are not only getting the highest quality bearings for the lowest price but the top brand in the industry.
- ✅ FastEddy Bearing Kits include all the bearings to upgrade your R/C to peak performance. Experience faster longer and smoother runtimes with peak performance.
- ✅ Trusted High Quality Chromium Steel 52100 (GCr15) Precision Races and Balls are used for the construction to ensure longevity and the highest possible quality available.
- ✅ Our proprietary high heat low drag synthetic lubrication formula that will last the life of the bearing allowing you to reach top speeds for extended periods of time.
- ✅ Low drag minimum contact rubber seals will keep contamination out and extend the life of your bearings.
Features:
Specs:
Height | 0.3 Inches |
Length | 2 Inches |
Weight | 0.0125 Pounds |
Width | 3 Inches |
6. 10pcs 2x5x2.5mm MR52-ZZ Precision Ball Bearings Chrome Steel, Metal Shield
Chrome Steel 52100 (GCr15) Precision RacesChrome Steel Balls
Specs:
Height | 0.6 Inches |
Length | 4.2 Inches |
Number of items | 10 |
Weight | 0.01 Pounds |
Width | 4 Inches |
7. 10x19x5mm Precision Ball Bearings ABEC 3 Rubber Sealed Blue (10) 6800-2RS
- Chrome Steel 52100 (GCr15) Precision Races
- Chrome Steel Balls
Features:
Specs:
Height | 0.7 Inches |
Length | 5.1 Inches |
Number of items | 10 |
Weight | 0.01 Pounds |
Width | 4 Inches |
8. 5x10x4mm Precision Ball Bearings ABEC 3 Rubber Seals (10) MR105-2RS-BU
- Compatible with Axial: AXA1218, Arrma: AR610002, ECX: ECX1015, Losi: LOSA6954, HPI: B021
- Compatible with Traxxas: 5115, TLR: TLR6932, Team Associated: 25237, Vaterra: VTR237004
Features:
Specs:
Height | 0.6 Inches |
Length | 4.2 Inches |
Number of items | 10 |
Weight | 0.01 Pounds |
Width | 4 Inches |
9. Traxxas 5114 5x8x2.5mm Replacement Precision Ball Bearings MR85-2RS (2)
- Chrome Steel 52100 (GCr15) Precision Races
- Chrome Steel Balls
- Compatible with Axial: AXA1213, Losi: LOSB1728, HPI: B020, Tamiya: 42111
- Compatible with Traxxas: 5114, TLR: TLR23700, Team Associated: 31400
Features:
Specs:
Height | 0.1 Inches |
Length | 4 Inches |
Number of items | 2 |
Weight | 0.01 Pounds |
Width | 4 Inches |
10. 20x32x7mm Precision Ball Bearings ABEC 3 Blue Rubber Seals (2)
- Quality ABEC 3 Races, GCr15 Chrome Steel Races & Balls, Rubber Seals
- This Bearing is Compatible with Part #: HPI: B094
Features:
Specs:
Height | 0.28 Inches |
Length | 0.79 Inches |
Number of items | 2 |
Weight | 0.01 Pounds |
Width | 1.26 Inches |
🎓 Reddit experts on rc engine bearings
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where rc engine bearings are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
The steering linkages limit front suspension travel. You want to taper the holes on both end to stop them limiting front suspension travel. When the suspension hits those limits it can make the car do unpredictable things.
Pick up some 1,000,000 weight diff oil. Put that in the front, use the kit grease in the rear diff. Or if you're willing to throw a few more dollars at it, use 200k out back. When you aren't diffing out, life is much better. Also, if you wanna slide around like your favorite rally star put the million weight out back, and the 200k out front. :-) (it's 5 minutes to make the swap..)
Pick up a "decent" steering servo. I like the Turnigy D99 when i'm feeling cheap.
I run the TT01e in Euro truck... so I've got some time on mine. :-)
Buy bearings! https://www.amazon.com/Tamiya-TT-01-Chassis-Sealed-Bearing/dp/B00KKPG086/ref=sr_1_2?ie=UTF8&qid=1543398520&sr=8-2&keywords=tt01+bearings
And have fun! (Bug me if you need more advice)
​
I personally use these, but most people recommend avid RC revolution bearings for thier value.
From amazon, pretty sure local hobby shops might have them. I went with rubber seals insteal of metal. 5x13x4mm Precision Ball Bearings ABEC 3 Rubber Seals (10) 695-2RS-BU https://www.amazon.com/dp/B00ZVF8J3O/ref=cm_sw_r_cp_apa_i_723FDb3P3PMPW
It looks like it comes with plastic bearings in the manual that's online. I assume you just mean that it's an upgrade that should be done from the start? If so, should these bearings do me good?
Here is everything that I can see that is missing. I've listed everything except transmitter/receiver, charger, battery and body.
If you have all that plus what is pictured you're looking at $100+ in parts and that is still operating under the assumption that everything pictured is working. If you wanted to try to do this on a budget, I'd look at broken "for parts only" trucks on ebay or local craigslist. (You can get a new "roller" there for $179 btw)
TRA7022 chassis
TRA7026 Battery covers /vents
TRA7024X receiver box
TRA7043 shock mount posts / steering pivot / steering horn
TRA2080 steering servo
TRA7090 motor mount plate (I cant tell if its in the picture)
TRA7077 motor mount hinge and gear cover
TRA7015 body mounts
TRA7023 tie bars
TRA7158 rocker arms
TRA7037 skid plates
TRA7135 bumpers
Optional parts/upgrades:
TRA7121 Wing mount +
TRA7122/TRA7123/[TRA7122G] (https://www.rcplanet.com/Traxxas_Wing_with_Decal_Sheet_Exo_Carbon_Finish_1_16_E_Revo_VXL_p/tra7122g.htm) Wing
TRA7184 wheelie bar assembly
Full bearing kit (if you're rebuilding anyways might as well replace missing/shot bearings)
Stainless steel screw set optional but it makes the truck easier to work on later especially if you drive in wet conditions.
chassis brace aftermarket chassis braces (can help prevent future chassis breaks)
These WILL fit:
https://www.amazon.com/2x5x2-5mm-MR52-ZZ-Precision-Bearings-Chrome/dp/B00TVPSCVO/ref=sr_1_1?ie=UTF8&qid=1502528708&sr=8-1&keywords=2mm+bearing
https://www.amazon.com/Miniature-Bearings-MR63ZZ-L-630-673ZZ/dp/B00ZHSQX42/ref=sr_1_1?s=industrial&ie=UTF8&qid=1502528834&sr=1-1&keywords=3mm+bearing
Here's an amazon link: (hope it's allowed)
https://www.amazon.com/10x19x5mm-Precision-Bearings-Rubber-6800-2RS/dp/B01BO7USG8/
@OP, you're looking for 10x19x5mm bearings. If you want ceramic, check out eBay but you're not going to notice the difference.
I know this is old post but when i frist build my D-Bot is couldn't get the gantry to move worth a damn. It all stemmed from the awful Chinese bearings in the wheels. The worst part was that it was nearly impossible to get the bearings out of the wheels without nicking the delrin.. I endded up getting all new wheels from open builds and some good quailty bearings. Everything moves like butter since. I truly believe its worth the extra $$
For affordable break barrel for humane squirrel kills I got this : https://www.amazon.com/dp/B004V959NO/ref=cm_sw_r_cp_apa_SOFBybKH01K1C
The stock trigger pull is crap but it can be fixed with one of these: https://www.amazon.com/dp/B00NKS95HS/ref=cm_sw_r_cp_apa_UPFBybGPAWKWZ
There are youtube tutorials for this if you decide to try it.
EDIT:
This is the weird big bearings on the back of the V1's.
What to search for:
6804 20x32x7mm
There's shit everywhere.