Reddit mentions of Aluminum Tape / Aluminum Foil Tape – Professional / Contractor-Grade - 1.9 inch x 150 feet (3.4 mil) - Perfect for sealing & patching hot and cold HVAC, Duct, Pipe, Insulation home and commercial

If you haven't done the wheel slip fix then your motor is slipping on the wheel. That's likely the root of your "traction" issues. I bought this tape https://www.amazon.com/gp/aw/d/B01FROBUXE/ref=ya_aw_oh_bia_dp?ie=UTF8&psc=1

You have to take the wheel skin off, wrap about 2 layers of that tape around the motor, then slide the wheel skin back on. Your performance will improve greatly.

Aluminum Tape may be what you're looking for. People use it for prop making all the time. It can be polished to a pretty good mirror finish.

Edit: Fixed link.

Find ways of protecting yourself while you're sitting still and sleeping, as that's when you're most vulnerable. I've written about radiosurgery, which is the act of destroying select tissue with electromagnetic radiation. There's a real threat of permanent brain damage. Do what it takes to stay healthy.
What is your budget?

I've tried the following (from /r/emshielding sidebar):

• Twin-size 8ft x 4ft conductive blanket: PET felt sandwiched around a copper layer (copper taped to the PET felt's aluminum backing), w/ground braid to wall outlet. Try without grounding first. Use hot glue for a flexible bond between the layers.
  
• Aluminum panels connected end-to-end with aluminum tape, with outer copper flashing layer, around the perimeter of a bedframe, to test nearby horizontal line-of-sight vectors (even if through the walls).
  
• Steel panels coated with layers of butyl rubber products for damping.
  
  I would recommend instead of the above (which was me prototyping and testing vectors), do it the right way the first time, and build my ventillated sleeping enclosure (~$1,000 for aluminum, plus add'l layers), and coat it with layers of shielding materials (copper flashing > butyl > sheet steel > buytl > sheet lead > butyl), until you achieve complete relief. Don't skimp on the fans and power supplies.

I used Aluminium tape, like that: https://www.amazon.com/Aluminum-Tape-Foil-Ducts-Insulation/dp/B01FROBUXE (not exact brand, I purchased the tape at a local shop). The glue on that is MORE than strong enough to hold onto the lid without moving. That type of lid normally has indentations in it, but I filled them with cardboard before putting the tape on top. It also makes for a more even surface, so I could apply the LED strips more easily :3

grab a roll of this with the part.. it'll prob be in the same section

https://www.amazon.com/Aluminum-Tape-Foil-Professional-Contractor-Grade/dp/B01FROBUXE

you can bend/cut the corrugated side and jam it in the hole.. and make it airtight with the foil tape.

I use foil tape and rolled up towels. You can also tape up a piece of plexiglass/lexan/whatever over top of the window to create another buffer.

Looks good. May I suggest you go get some aluminum tape for the blade. LIke the link below. Fold it around the blade and smooth it out with your fingers. Gives a good blade effect. Also, the smoother the wood of the blade the smoother the tape.

https://www.amazon.com/Aluminum-Tape-Foil-Ducts-Insulation/dp/B01FROBUXE

It's a hot mess at the moment and I don't have a good photo, but here are the pieces:

• Inline fan https://www.amazon.com/gp/product/B01CTM0JF2/
  
• Flexible duct like this https://www.amazon.com/gp/product/B017S4JPW4/
  
• An HVAC "Boot" like this https://www.amazon.com/Midwest-Ducts-Degree-Angle-Register/dp/B00BHLFBAK/
  
• a 6" "Wye" connector so I could connect multiple machines https://www.amazon.com/Single-Wall-Galvanized-Wye-Tee/dp/B00E0Q4902/
  
• Foil tape designed for HVAC https://www.amazon.com/Aluminum-Tape-Foil-Ducts-Insulation/dp/B01FROBUXE/
  
  I put the Amazon links for reference, but shop around. Some of this stuff is much cheaper at Home Depot or other online stores.
  
  I use the foil tape to connect a "boot" directly to the back of the case my mining rig is in. Then connect the flex duct to the boot. Connect the other end to the inline fan. Connect a second piece of flex to the output of the fan and hang the end out of the window.
  
  I've found pulling the heat out works much better than blowing cold air in.
  
  If you have an open mining rig, I've seen people put up small tents like this one: https://www.amazon.com/Valuebox-2x2x4-Small-Indoor-Hydroponics/dp/B01GCHXUVU/ and then just connect the duct to it. That seems to work okay too.

https://www.amazon.com/Aluminum-Tape-Foil-Ducts-Insulation/dp/B01FROBUXE

Hard alumium tape with adhesive backing.

Interesting.... I wonder if the insulation aluminum tape would also work. I have this already at home: https://www.amazon.com/Aluminum-Tape-Foil-Ducts-Insulation/dp/B01FROBUXE/ref=sr_1_sc_2?ie=UTF8&qid=1543196012&sr=8-2-spell&keywords=insulatin+tape

I would suggest an ultratherm. They are awesome UTH's. But as far as securing this to the tank, whether is the zoo med or the ultratherm, use aluminum duct tape.

Ultratherm - https://beanfarm.com/collections/heating/undertank-heaters (Same company also sells on Amazon)

Aluminum Tape - https://www.amazon.com/Aluminum-Tape-Foil-Ducts-Insulation/dp/B01FROBUXE/ref=sr_1_3?ie=UTF8&qid=1525098985&sr=8-3&keywords=aluminum+duct+tape

After securing the heater to the tank, Insulate at least the back, if not 2-3 sides. The best stuff to use is reflectix.

Reflectix Insulation - https://www.homedepot.com/p/Reflectix-16-in-x-25-ft-Double-Reflective-Insulation-with-Staple-Tab-ST16025/100012574?MERCH=REC-_-PIPHorizontal2_rr-_-100052556-_-100012574-_-N

Doesn't get any better than those three links, IMO. Here is a picture of how my tank uses them. https://imgur.com/mfhU7Tk (this was mid-construction)

Also I used this tape to keep the mat attached :https://www.amazon.com/Aluminum-Tape-Foil-Ducts-Insulation/dp/B01FROBUXE/ref=zg_bs_256160011_13?_encoding=UTF8&psc=1&refRID=8MWBZYPB8AWYK1CSQHJK