Reddit mentions of Beerings 8mm Malt ABEC 7 Skateboard Bearings

I'll start with the non-printable mods:

Replaced the PSU with a 750w ATX PSU I had lying around.
If you do this, you will more than likely need to add a power resistor to the 5v rail. I also removed all the original wires and connectors from the PSU and resoldered just what I needed with better rated wire.

Glass bed on top of the aluminum. I just went to Lowes and got them to cut a few pieces of single pane glass.

Mosfet circuit for the heated bed:
https://www.amazon.com/BIQU-Power-Module-Expansion-Printer/dp/B01HEQVQAK/ref=sr_1_1?ie=UTF8&qid=1493092441&sr=8-1&keywords=3d+printer+mosfet

Upgraded Y Carriage:
https://reprapchampion.com/collections/heated-beds/products/anodized-aluminum-y-carriage-plate-upgrade-v2-for-prusa-i3-reprap-3d-printer

New Belts:
https://reprapchampion.com/collections/linear-motion/products/10-meters-6mm-width-gt2-timing-belt-for-reprap-delta-3d-printer-kossel-rostock

Geared Pulley to replace the smooth one:
https://reprapchampion.com/collections/linear-motion/products/3d-printer-idler-pulley-aluminum-dual-ball-bearing-3mm-bore-16-teeth-gt2-belt

Upgraded Heated Bed, this bed heats up slow and I also lost a little bit of build volume. I plan on getting something better here very soon. Once it's up to temp it works well though.
https://reprapchampion.com/collections/heated-beds/products/new-improved-mk3-aluminum-reprap-3d-printer-prusa-i3-heated-hot-bed-build-plate

Inductive Sensor for auto level:
https://www.amazon.com/gp/product/B01LWNCY4C/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

Copper Tape Because the inductive sensor can't see glass I put this on the bottom side.
https://www.amazon.com/Tapes-Master-10ft-Copper-Foil/dp/B00Z8MCJW2/ref=sr_1_6?s=industrial&ie=UTF8&qid=1493092625&sr=1-6&keywords=copper+tape

Firmware:
To get the sensor working, you'll have to change the firmware unless you only want to use it as a limit switch. The only option that i'm aware of is Skynet which is based on Marlin and works fairly well. You can find that on their facebook page: https://www.facebook.com/skynet3ddevelopment/

Blue LED Extruder Fan (because the original broke). I don't remember where I got this from. I'd like to find an RGB one! ha

I added a bunch of WS2812 LEDs controlled by an Arduino at the moment, I am using OctoPi so eventually i'll have that control them but at this point they're set to UV colors because it looks cool.


Printed mods:

Frame braces:
http://www.thingiverse.com/thing:1857991
http://www.thingiverse.com/thing:1430727

Y Carriage Risers:
The Y carriage sits too low and will smack into the Y axis motor so I made these risers to solve that:
http://www.thingiverse.com/thing:2226564

Y Belt Clamp: You'll need one for the new carriage, but I cannot find the one that I used.

Auto level bracket: Though I only have PLA and it kept warping so I made a metal version of it:
http://www.thingiverse.com/thing:2006986

Anti-Z Wobble I modified this but no longer have the file, I also printed a cylinder to wedge into the hole above the lead screws.
http://www.thingiverse.com/thing:1858435

Bearings I used:
https://www.amazon.com/Beerings-Malt-ABEC-Skateboard-Bearings/dp/B005NFXHQG/ref=sr_1_2?ie=UTF8&qid=1493094188&sr=8-2&keywords=beerings

Belt Tentioners I can't remember which ones I finally used.

I think this is everything. If I remember something else i'll post it.