Reddit mentions of Bondo Bumper Repair Kit, 00280, .34 fl oz

This might help in giving you some direction, though I'm not sure if it's exactly what you're looking for: http://www.amazon.com/Bondo-280-Bumper-Repair-Syringe/dp/B0046VN8JO/ref=sr_1_1?s=automotive&ie=UTF8&qid=1373148270&sr=1-1&keywords=bumper+repair+kit

The mesh is used as the backing to reinforce the split, the epoxy is basically used like bondo for plastics, sandable with low grit sandpaper.

I used it when I removed some emblems on my rear bumper and needed to fill in the holes, it worked perfectly. The bumper itself was pretty messed up, with random marks and divets where other drivers have gone into the rear, license plate first. The epoxy worked great as a filler, I was able to restore the shape and make it smooth without much effort. That said, I'm not sure how well it'll work if you're stitching together 3-4 inches of side skirt together, though I can see it holding its shape together, especially if it's not in a high traffic area.

Just get this:

https://www.amazon.com/Bondo-280-Bumper-Repair-Syringe/dp/B0046VN8JO

Then get a can of this:

http://www.paintscratch.com/touch-up-paint-directions/tricoat.htm

The issue with tri coats is it is almost impossible to blend within the color which white is hardest since it gives off the most hues.

If you ran over a tire the underneath of your car is the bigger issue. That underbody shield can actually cost quite a bit to replace and if you ever get an oil change they are going to wonder where it is.

So I would just get a paint scratch kit and then worry about repainting the whole bumper later.

The tri coat paint costs more in a can but its not like BMW prices and if a shop gives you an issue about blending to the rest of the car I would just say fuck it. I have never seen a tri white that was perfectly blended even from the factory and on white its harder to blend but its harder to tell a bad job too.

It comes down to how long do you want it to last?

You're getting a lot of old school suggestions here with bondo and fiberglass stuff. There are products for this that work that consumers can get which are significantly easier to use and more effective.

Pick up what is called a "bumper repair kit". I know you are not preparing a bumper but it contains everything you need. The kit is sold at most auto store places. It contains a two-part dispenser of a black urethane epoxy and a sheet of webbing and some plastic tabs. When I get to my computer I will come back here and post a YouTube link on the basics for how you can repair this it's not the exact same issue but the similar process will work.

The kit looks like:
http://www.amazon.com/Bondo-280-Bumper-Repair-Syringe/dp/B0046VN8JO/ref=sr_1_1?ie=UTF8&qid=1420828130&sr=8-1&keywords=bumper+repair+kit

Use that kit with this method:


https://www.youtube.com/watch?v=ZqtOGI2To7s

Follow the steps in this video as they apply to you, but use the the bumper repair kit you buy at the store. The same prep and application method. If you can't get to the backside of the cut, that's okay. If you have a drill, drill two small holes on each side of the cut, then apply the repair material over the little holes you drilled, and the big one you are trying to fix, all with one patch. The material will go through the little holes you drilled, expand, then dry-effectively the same thing as a rivet, but stronger and easier.

I've had good luck with this coupled with a fibrous backing like fiberglass.

Also, the correct answer is zip ties. Chicks dig scars, but whatever.

doesn't look too bad. try this with some creativity and color match paint. wont be perfect, but way less than $700

Then you can try Bondo 280 Epoxy Bumper Repair Syringe Kit

Don't use regular Bondo though, your bumper needs a certain amount of flex. Regular Bondo would be too hard.

I cracked mine as well, clean it up, use sand paper on the back, apply mesh and bondo to the back side and fill cracks with bondo, apply clamp works surprisingly well. It will still be sort of visible unless you paint it.

Bondo 280 Epoxy Bumper Repair Syringe Kit - 0.34 fl. oz. by 3M http://www.amazon.com/dp/B0046VN8JO/ref=cm_sw_r_udp_awd_YB-tub1HXVC4W

Like the others have said, pull the pumper cover off, and take a heat gun and push them out. From personal experience though, it doesn't take much heat to make that plastic malleable, so take it slow. If you can't get it perfect, this Bondo bumper repair kit is great too. Just put it on, let it cure, sand it down and finish it with some glazing putty. This formula worked well for me and I repaired a puncture with it. Also, if you need paint, Sherwin Williams automotive seems to be significantly cheaper than any of the online color match sellers.

You can fill chips and this hole with body epoxy and sand then wrap over the top of that. Most automotive pait stores have it. Amazon link

This is the bondo you would recommend? https://www.amazon.com/Bondo-280-Bumper-Repair-Syringe/dp/B0046VN8JO/ref=sr_1_1?ie=UTF8&qid=1517862027&sr=8-1&keywords=bondo+epoxy

Would the 3M or JBweld epoxy work as well?