Reddit mentions of Honbay 25Pcs Silver Tone Alligator Clips Test Lead Crocodile Clamps

Hangers with clips (Either alone or on the hanger). On the hanger is fun because you can usually slide them towards or away from each other, and the tension will hold them a bit in place.

Vice grips - the weight can be really satisfying

Binder clips - even better are the ones with the magnet on the end!

Alligator cilps

Jumper cables, but probably need some heavy padding.

Chopsticks and tight (small) rubber bands.

Almost anything with "clip" or "clamp" in the name. So, for instance, if you have those heavy-duty clamps that get used to hold down a tablecloth at an outdoor picnic, that can be fun. Or woodworking clamps.

There are also things you can do to up the intensity even with gentle things. Ex: after the clothespins have been on a while, turn them 90 degrees. Or go more for the edge of the nipple rather than the base. Or get a spatula/paddle and slap your nipples to get them tender first.

You can really have fun with anything that squeezes. I remember as a kid using two clipboards. It was tough to get the nipple in, but was a fun sensation.

Hope that gives you some ideas!

I believe I have finally decided on my first Gunpla, the HG Age II Magnum and want to make sure the items I have added to my Amazon cart are ideal or not for a beginner/future use for HG and MG kits. The list is as follows:

• Gundam Model Builder's Cutting Mat 12"x9"
  
• Findfly 9Pcs Gundam Model Tool Kit
  
• Gundam Marker Value Set
  
• Mr. Super Clear Flat Spray
  
• Bamboo Skewers
  
• Alligator Clips
  
• ScotchBlue Painter's Tape
  
• Styrofoam Blocks
  
  I know that this sub has a list of tools and tutorials, but because I'm trying to budget, I was thinking no more than $100 would be ideal for me to start with. Since I'm beginning with HG models, I don't think I need a full set of Gundam markers, but if it's needed/required/highly suggested, I might pick them up as well.
  
  So I have read and seen that top coating and panel lining are essential for MG models to make them pop. Are they just as essential for HG model kits? Looking at pictures of the Age II Magnum I'm planning on getting from Amazon, it doesn't seem to have a lot of indents for panel lining. Of course, I could be wrong and be blind as a bat. If I don't do any sort of panel lining, is it still a good idea to add a top coat regardless?
  
  Also, how soon can one get into MG kits? I was originally going to jump straight into either the MG GM Sniper II or the RX-78-2 Ver 3.0 but after doing some research over the past few days, I've decided I'll be doing a few HG's to begin with as I haven't built model kits since I was like 7 or 8 with my dad. I'm thinking after the Age II Magnum, I was thinking about getting either the HG Double O Diver or the HG 00 Shia Qan[T]. Maybe after I complete the 3 HG's I've listed, is it possible to jump to the the GM Sniper II?
  
  TL;DR:
  
  

• Are the items I have listed a good starting point?
  
  
• Is a full set of Gundam Markers a necessity for HG/beginners?
  
  
• Are panel lining and top coatings important for HG model kits?
  
  
• Is it okay to use top coat on an HG model if no panel lining is used?
  
  
• Edit Do people usually top coat the accessories? I can't seem to find any info on that.
  
  
• What color panel lining pens do people normally use based on different parts of Gunpla's?
  
  
• What level of skill should one be at before getting into MG model kits?