Reddit mentions of Wagner 0503040 HT3500 Digital Heat Gun, 12 Temp Settings 250ᵒF-1350ᵒF, soften paint, caulking, adhesive, putty for removal, shrink wrap, bend plastic pipes, and loosen rusted nuts or bolts

Thanks! :D

The wax is a nice finish so far. I was messing around with some wood I found last night and dinged the wax finish with a saw. A glob of wax and about 45 seconds and the ding was gone! I'm sure if I actually hit the wood it would be a little harder to fix, but none-the-less I think wax is a good way to go.

I've used wax for lots of other projects too. It's a nice, non-coloring protector and water resisting barrier. Greta for indoors. I never tested it outside, but probably not as good outside.

The way I put the wax on is very similar to a car: first smooth the wood down to about 150 grit sand paper. Then throw a bunch of wax on and rub it into the cracks and crevices, any big voids you can just throw a big glob on the them and rub them down a bit. wait about 20 to 30 minutes for the wax to set. Then I attach a shop rag (yeah, the ol' red rags) to my orbital sander and buff away to a semi-shine. Repeating the process gets more shine.

You can also lightly heat the wood with a heat gun after you've rubbed wax on but before it's dry to open the wood pores and let the wax really penetrate the wood. I've only done this once (not on my workbench) and I was nervous of it causing the glue to fail and boards to separate - it didn't though. But always test it out first before you go and take reddit advice!

What size/type of tubing are you using?

I use 12mm bitspower acrylic or 12mm PETG barrow tubing.

My favorite set of tools are:

https://www.amazon.com/3Pcs-Hardline-Mandrel-45-90-180-Rigid/dp/B01IDVQC8Q

https://www.amazon.com/Wagner-Digital-Heat-HT3500-503040/dp/B00BV14VMA

https://www.amazon.com/Wolverine-PST085-Inner-Outer-Reamer/dp/B0002YVLHA

For the barrow PETG:

For cutting: https://www.amazon.com/Apollo-Valves-69PTKC001-Plastic-Tubing/dp/B0054YDY0A or similar

The insert: https://www.amazon.com/Barrow-Silicone-Bending-Tubing-Black/dp/B01M9CTQ1S for when I buy barrow tubing (it's 8mm ID, 12mm OD)

For the bitspower acrylic:

For cutting: https://www.amazon.com/Premium-Mini-Hack-Blade-Angles/dp/B01COE3YZ2 or similar

Edit: Found the insert: http://www.performance-pcs.com/bitspower-silicon-bending-cord-10mm-clear-1m.html

Cleaning up and shaving down to size (this thing is amazing): https://www.primochill.com/products/primochill-rfb-rigid-tubing-finishing-bit

Buy the insert made by the company that makes the tubing for best compatibility imo.

Also I use a belt sander.

Edit: Also I use Mayhems dyes with either white pastel or their X1 clear. Both should be safe with PETG or Acrylic.

I love projects like this. Your furnishings feel much more your own, and they take on a sense of permanence you can't get with big box furnishings.

A heat gun and putty knives work very well to remove the stickers. Use a low setting, don't keep the heat focused on one area for too long and keep an eye out for browning, singeing, smoking, and fire. You've got lots of space to work with so skip around to allow the wood to cool. You'll potentially be removing whatever finish is on the couch if you are too heavy handed and or use too much heat. If you plan on refinishing use the heat gun and putty knife to remove the finish.

You can try just scraping with a razor blade to remove most of the stickers and then saturating the area with full strength degreaser, such as D-Limonene.covering the area with a paper towel to keep the degreaser in place.

A couple of razor tools to consider: 4" wide short handled for large areas with thick layers of stickers. Smaller razor scrapers with metal and plastic blades. Plastic detail scrapers might be useful too.

Instead of using Goo Gone I like pure D-Limonene solution. It's a potent degreaser extracted from citrus peels and contains no petroleum distillates, unlike Goo Gone. It also comes in food safe solution - though to be safe for digestion it really does need to be quite dilute.

Use the putty knife and rags or gauze to clean the adhesive from the wood. Large Woven Gauze Sponges are more scratchy and will give more traction with absorption. Rolled Stretch Gauze Bandages have the same great absorbing properties but they're softer and great for detail work. You'll get to know what you prefer - I'm partial to gauze sponges. They're cheap and I just toss them into the compost bin as long as they aren't too bummed up with adhesive top.


To remove the degreaser dish soap and rubbing alcohol work well. I like Dr Bronner's castile soap diluted for dishwashing. Wipe down with 90% Isopropyl Alcohol. You should be good to move on to your next step, probably sanding and smoothing, patching any holes or gouges to prep for staining and finishing or painting.

I linked a whole bunch of products to give you an idea of what will work for certain applications. There are definitely other ways to achieve the same goals, this is just how I tackle this task. Please don't order everything listed here at once, see what works from you. I link Amazon because they have everything but locally owned small businesses are an invaluable resource and great when you get stuck in a project.

Don't forget your PPE'S!

Dust Mask - I like this one as you can vacuum the filters out to extend the life and reduce waste. It has a smaller profile too - my husband actually doesn't complain about wearing it, just puts it on.

N95 Respirator
Replacement filters available on Amazon

Comfortable Safety Glasses or Goggles

Heat Resistant Gloves

Long Cuff Gloves Disposable

Some type of work gloves

Good luck!