Reddit mentions: The best soldering stations

Preface: for some ungodly reason Mass Drop expects people to create an account before showing what the page has.

What is on the page is the description of the keyboard along with everything in the kit.

Here is an image of the web page to fix this so that you can see what keyboard I am talking about: https://minus.com/lE02abi6ORu87.png

It is stupid I know, but that is how they are for some reason.

You don't have to use Facebook to log into it though thankfully.

Alright, so this kit is finally back as an option on Mass Drop after over a month or two of absence, and it is on it's third or fourth Mass Drop group buy, all of which have been successful with no complaints from buyers amazingly.

Ordering it as a group buy is the only way to get this keyboard and it isn't offered anywhere else on the planet.

Everyone who has tried the keyboard is in love with their ErgoDox and how comfortable using the brilliant design is.

The ErgoDox keyboard is an open source hardware, open source software design, which as people who use GPLv3 software I hope you can appreciate how huge that is in light of how unapproachable hardware design has been in the past, plus with the group buy concept instead of the total cost being over 1500 USD (I priced all of this thinking to make my own being very unhappy with the lack of any intelligence present among keyboard manufacturers) it is less than 300 dollars, even after purchasing keycaps, which is huge.

What is brilliant about this keyboard, and I mean absolute genius in a domain defined by the lack there of is that it uses open source hardware with the specifications fully available, open source software for the firmware, the micro controller is very easily modified and installed thanks to their work on the configuration software, it uses all high quality parts including the very popular Cherry MX key switches (the mechanical part of a mechanical keyboard) for excellent tactile feedback and soothing ambient noise through the clickity clackety of the key switches, provides everything you need in the kit, has excellent instructions for assembling them, and allows you to decide on your own term caps, for which there is another group buy for to bring the cost of those way down.

You will absolutely love having thumb keys, which I use for all of my modifier keys and it saves my hands from career ending emacs pinky thankfully. Thumb accessible keys is an absolute boon for the information worker that has long days and nights.

I have liked them ever since experiencing them on a Kinesis Contour Advantage keyboard, and I cannot recommend that design enough.

But wait, there's more: in addition to all of that the keyboard also brilliantly went with not only a mirrored, symmetric layout for the keys and frame, and it also had the insight and genius to go with a split-keyboard layout so that the keyboard can not only accommodate a variety of human sizes, but doing so also ensures that the user can conform to proper ergonomic keyboard uses that entails having the arms and hands orthogonal to the key layout.

And even then, this design has another stroke of genius: removal of the typical function keys and escape key.

I know, you are thinking this is insane I need those.

And yes dear reader, I thought so too, but here is why this is actually a good thing, by not having that row there not only does it save space, it also ensures that you do not have the courage to try and chord the function keys without leaving the home row and anger the tendon gods in the process.

Thanks to the multiple layouts available (more not that below) you don't actually lose access to these, they just move to wherever you have decided to locate them.

This design is the most comfortable and ergonomic keyboard design I have ever seen and it puts the rest f the industry to shame for their hubris that has ruined many a career and been generally bereft of excellence as it makes no sense to design a keyboard this way now that we are not using bloody type writers from middle ages.

I am going to order at least two myself, one to use then a backup in case I can't get it in the future, which is what has happened to another keyboard design I liked and made it impossible to get or very expensive. Also, so I can take one to work and leave another at home.

Anyways, for those of you who do not have electronics experience and are worried about soldering things together or flashing the firmware on the micro-controller, do not be alarmed.

It is quite easy if you have moderately steady hands, plus you will learn a cool skill and hopefully take up the joy of hobby electronics.

You will be able to make your own ham radios and mess around with the great arduino micro-controllers and do all kinds of awesome tricks with sensors in your residence or wherever.

I recommend getting a fine point soldering iron and desoldering pump sucker for picking up solder off the pcb if you need to redo a trace. A soldering iron like this will work fine for this project.

A beautiful person took the time to make a how to assembly video showing the entire process too, which is superb: https://www.youtube.com/watch?v=x1irVrAl3Ts

This image has the assembly instructions that cover the soldering and other hook ups: https://i1.minus.com/ibeVgc381INcEF.jpg

Here is the configuration page you use to set up the layout and the site generates the hex file you need to upload to the firmware for you, which is the tricky part normally: https://www.massdrop.com/ext

Here's an image mirror of that in case the previous link does not work: https://i.minus.com/ivk3kHgNCgsTl.png

Here is an example modified qwerty layout. https://minus.com/l5Tnw5yL3TuMb.png

There are multiple layers because on this keyboard you can have multiple layouts that you jump up and down through via the L+ and L- keys, which is absolutely brilliant design.

L+ moves up in the layout stack, and L- moves down in the layout stack.

Also, you can configure keys to move up or down through two layers at a time for ever faster switching between layouts.

Having a way to progress through multiple layers of layouts is something I had not thought of in my prototype design and would have sorely missed having such a wonderful feature if I had not seen the ErgoDox keyboard before I had a go at having my own custom layout manufactured.

I really cannot hype this design enough, from quality to its concept to its execution, every aspect is flawless and free as in freedom on top of that.

I hope you all consider grabbing this beautiful product.

I realize it is considerably pricy compared to other keyboards, although within a normal price for ergonomic keyboards, but this is absolutely an investment in your own health and career regardless of your age that will pay for itself.

It is a pittance to pay for compared to the agony that will succeed if you happen to come down with crippling repetitive stress injury (RSI) or carpal tunnel syndrome (CTS).

As someone who has had that, and also as someone who did not take the situation seriously, it is completely devastating and takes months to heal even with great precaution and doing everything possible outside of surgery (which at most will have 80% return of functionality in your hands and ensure that you will be maimed for life in the process).

It is much, much better to go with the ounce of prevention instead of the pound (and months to years) of cure along with hundreds of dollars in the process that entails an slew of treatments.

Even one lost paycheck due to injury will cover the cost of this investment in yourself.

If you choose not to go with this product, at least take the time to invest into researching how to avoid injury and what you can do to give yourself the best chance of staying in the game rather than being sidelined by injury and wasting your own time and brilliance.

Xah has reviews of other keyboards (none of the ErgoDox that I know of though) that are ergonomic options as well. You can find those reviews here: Xah's reviews.

Cable

• If you're stateside, Anixter is our main supplier since they have branches all across the country. However we use several local vendors as well, NedCo in Las Vegas, Pacific Radio in Los Angeles, etc.
  
  
  
• EWI looks fine, I haven't ever worked with it personally, but looking at their site it looks fine.
  
  
  
• My company personally uses Belden whenever possible for installations and for inside racks. For touring and studio a mixture of Mogami and Canare for microphone, instrument cable etc. For speaker cable I personally prefer CCI/Coleman cables. I've seen those jackets take extreme beatings in all environments and all sorts of machinery run over them.
  
  For your question about 3.5mm to TS, you really just need any audio rated cable and what it's purpose is. For these I personally find it easier to purchase a stereo 3.5mm and solder on the connector I need; RCA, TS, XLR, etc.
  
  
  
• When looking you should shop around multiple vendors and get pricing for various cables at each location. See how their pricing and shipping differ.
  
  
  
• Most 22-26awg signal cable will use foil due to it's small size. Outside of that should be a twisted dump wire. Solid dump wires I've found are not the best for audio as they break easily if a cable is over extended/bent too far. For microphone, as close to 100% coverage over your other pairs is ideal. Any reputable cable manufacturer will provide this information.
  
  
  
• Microphone cable is the same cable as instrument cable. The only difference is there is an extra wire. A balanced XLR will have a dump wire/shield, a hot, and a neutral. An instrument cable only has the dump wire/shield and the neutral generally. The only real thing to look for is the cable's resistance. Digital RCA should be around 75ohms, while Analog RCA is around 20-40. Same for DMX and Audio, DMX looks the same, but is around 110ohms, whereas audio cables will be around that 20-40ohms. This is done to protect the digital transmission of their square waves more, whereas audio doesn't need to and is a sine wave.
  
  Solder
  
  
• Each solder will have a different melting point, another key thing is to look at the melting point of the wires insulation/jacket. Most Lead based solders will have a melting range of 350-450°F. Generally the silver solder will melt around 1,145°F, this is known as easy silver solder, as it is only around 56% pure, hard flow silver solder is closer to 1,375°F. What you'll typically find/use is 70/30 or 60/40 which should be around 350-375°F range. Why some people prefer Silver Solder is for clarity, it has less imperfections that disrupt the flow of the electrons. However your usual 70/30 or 60/40 is just fine as well, the majority of cables you'll work with have been made with this type of solder. One key thing to look for is that the solder you have contains a Flux Resin Core. This helps the solder flow easier and bond to other metals easier.
  
  
  
• Watch videos on youtube, make sure you have a decent Iron [I personally prefer Hakko] the Digital FX888D is a great inexpensive soldering station for beginners. The next thing to do is to practice. Practice, practice, practice. Cut off a few feet of wire and go at it, practice tinning and terminating over and over again. Another thing is to practice undoing a connection. To do this you'll want to put your tip on the joint, and then add solder with a flux resin core. Once solder melts, its melting point goes up in temperature, the flux and resin help to lower that back down to make it flow faster/easier. Then, if you don't have a solder sucker, just pull the wire out of the connection point and while the solder is still flowing tap it out onto a safe surface. This will remove the excess solder but will still make it tinned, ready for your next wire. Key point clean your tip! If your iron didn't come with a gold foil cleaner, get one, they're around $5-25 and worth every penny, here's a $5 one on Amazon. This will clean all the impurities off of your iron and make soldering easier and cleaner. If you're in a pinch and don't have one, a wet paper towel/cloth works. You want it to be wet enough that if you squeeze it with some good force water will come out of it steadily, but not so much water that it pools out when you press your iron against it.
  
  
• A station heats up very quickly, so if you have a shop, those are ideal. Having it well lit and ventilated is key, the fumes can be nasty. Additionally have the right tip on your iron for the job is key. For example, a tip meant to do 26awg signal probably isn't the best suited for then doing 10awg lines.
  
  
  
• Google, sometimes after a long day my mind blanks when making adapters for whatever I'm doing, and I just do a quick google image search. Otherwise, if you want it in book form, along with basically everything you'd need to know about the basics of tech, The Backstage Handbook.
  
  
  
• You should have the following,
  Stereo RCA to XLR Male
  
  Stereo RCA to RCA
  
  Male XLR to RCA
  
  Female XLR to RCA
  
  EP6 to NL4 and NL8, going both ways, ie One side Male Neutrik to Female EP6, and then vice-versa.
  
  1 Male to 2 Female XLR
  
  Then just a slew of various connectors to make anything that may arise.
  
  
  
• Amazon, Anixter, any electronics specialty store will have shrink tube. Be sure to check out how much it'll shrink when heated up, so shrink more than others. How to make them super clean is all up to how meticulous you are. Make sure you have a nice clean strip of the wire, and that your distance for stripping back the otuer jacket, and each wire's inner jackets is proportional to the connectors strain relief. You'll also want to make sure you sex your wire, ie, male XLR should go, Ground, Hot, Neutral when stripped Left to Right. Female XLR should start with the Neutral, then go Hot, then Ground. This will make for a cleaner look when it may be opened up, and less of a hassle when aligning the wires for soldering. For the actual soldering part you'll want to tin both your wire, and the solder point. Solder will flow to where it's hottest. By tinning these you are prepping the points to connect. You'll use less solder, and it will take less time. Once both sides are tinned, put the tip of your iron at a contact point of both the wire and the connector. Then wait a good 2-3 seconds and apply some solder. you won't need much. If you did it right the solder will melt almost instantly and then hold the iron there for another 1-3 seconds and both the solder on the wire and connector will now pool and flatten down naturally from gravity with the solder you just added. Pull your wand away and let it cool for a second or two before you let go of the wire. Shrink tube should be necessary in most XLR, TRS, RCA, NL4, connectors, but if you feel so inclined, then by all means do it. However, for this I recommend using a clear shrink tube. This will make it easy to check if something at the solder point is bad when troubleshooting a cable. For other cables such as an EP6 connector, I will always, ALWAYS recommend use of shrink tubing.
  
  
  
• Labeling depends on the context. For instals in say an audio rack, our typical scheme is U101-A, U101-B, U102-A, the U### = Rack unit number, the letter A thru B, C, D etx refers to the amp channel. For these I typically use 3/8 or 1/2 White or Yellow shrink tube labes with our Rhino Labeler. We do not however shrink them, this is done for service purposes. Depending on your angle when servicing you may not be able to read the label once shrunk, but if left unshrunk you can turn it so it can be read from wherever you are. Note, you should label both ends of the cable the EXACT same. For touring and rental you should put your name/company's info on a label of some sort and then place a piece of clear shrink tube over that. You want to make sure about 1/2-1" of the clear shrink tube carriers over the edges of your label. This will protect your label longer than if they're almost exactly the same length. It's also not a bad habit to run a piece of colored tape, label, whatever under the clear shrink tube on both ends to distinguish cable length. Every company has a different method, but the one I use is the rainbow.
  
  Red - 5ft
  
  Orange - 10ft
  
  Yellow - 15ft
  
  Green - 25ft
  
  Blue - 50ft
  
  Purple - 100ft
  
  White - 200+, one band =200, two bands = 300.
  
  Hopefully this helps you in some way, let me know if you have any other questions or follow-up to any of these responses! edits Grammar, phrasing, some links to specific items, etc.

For (bigger) diagonal cutters/pliers, I think the most BIFL are NWS with their "Titan finish". Knipex is a fairly close second, but I like the finish on NWS better. Both can handle hard and medium hard wire (including nails and screws) without a problem, unlike most Klein, Snap-On, etc. The biggest issue is finding NWS in the US. The NWS Fantastico Plus are the best diagonal cutters I've ever laid my hands on.

For precision cutters/pliers, Xuron. They're semi-flush (Xuron call them flush, but I'd still call them semi-flush) micro sheer cutters are great but thankfully don't seem to nick up easily like (Xcelite, Snap-On, etc.) flush cutters do. I like the ones with that are ESD safe, with extra long handles, and the lead retainer best if you're going to be populating a lot of circuit boards. Otherwise, their cheaper models are just as nice.

Wiha precision screwdrivers. I've given this set as a gift before. Wera for the bigger stuff if you need it. Wiha or Wera bits (only larger sizes, I've never found precision bits I've particularly liked).

Klein to fill in gaps.

Bondhus hex keys.

Find a nice used Fluke multimeter on eBay. 89IV go for under $200 and have pretty much identical features to the 189 (believe the 189 mostly just has a bigger inductance/capacitance range). Most universities will have someone tasked with calibration/maintaining the measurement equipment. Make friends and he'll probably calibrate it for you/teach you how/just let you jump in and try. Mine was falling out of the box after UPS drop kicked it to my door, but the calibration was still super boring as nothing needed adjustment.

Hakko or Weller soldering station. Easy to find tips, especially for Weller. WESD51 dropped to $99 on Amazon a couple times in the last year, great time to scoop one up for little more than the analog version. The Stahl Tools one Amazon sells is also good for dirt cheap, but not really BIFL; good luck on finding tips. Metcal is too rich for my blood, but if you ever happen across one that is cheap.

Kester "44" solder, accept no substitute. 63/37 or 60/40, but since the spool will last you half a lifetime, I'd probably go with the 63/37.

I have a love/hate relationship with wire strippers. Something like this usually gets the job done, but sometimes you'll get wire with a strange jacket size and they'll fail. For the automatic kind, this style works ok (especially if you adjust it to what you're stripping), but I usually like this style better; again, as long as the jacket isn't too small and you wire is in the right range. Sadly, I probably most often grab for cheapies like this. The adjustment screw is great if you have to do a lot of a certain size, but I tend to free hand them. It takes quite a bit of practice, but once you get the hang of it, it's the fastest. Thermal wire strippers are just too pricey for the home user, especially if you want to do PVC, teflon, etc. jacketed wire.

I also have a love/hate relationship with crimpers. I have some crimpers I got for Anderson Powerpole connectors from West Mountain Radio (largely because I couldn't believe how cheap they are-- connector-specific crimpers are usually many times the price they charge) and they were great for the Powerpoles. I even bought some of the other die sets, but I've been less happy with those. I often end up using a similar pair to these or the die on a pair of Klein lineman's pliers for the larger crimps.

I haven't actually used mine for anything yet because I kind of got burned out doing technical hobbies after a technical workweek, but I decided I'd pick up one of these anyway, which hits a lot of the electronics test stuff you mentioned:

https://store.digilentinc.com/analog-discovery-2-100msps-usb-oscilloscope-logic-analyzer-and-variable-power-supply/

Ton of features for the price.

I use a 8-channel Saleae logic analyzer at work which is awesome, has really nice-looking software, and is priced reasonably for a home lab, but the AD2 does a lot more for not much more money. A decent multimeter is always useful. I used a $50 Radio Shack unit for a long time, but when it died, I picked up a really nice used Fluke 179 on eBay. Get some extra fuses for the fused current ports.

I definitely would buy a home 3D printer if I were into technical hobbies right now. I spent so much time using hand tools to lash together ugly electromechanical stuff for ham radio antennas and tuning networks before 3D printers were affordable. Agree that digital calipers are a great addition. I've found really cheap ones to be adequate at home.

For general electronics stock, even if the work's focused on microcontroller/IoT/digital, I like stocking up on small general-purpose capacitor and resistor assortments from places like Jameco, and then I order extra on the 220, 330, 1k, and 10k ohm resistors. For caps I'll get extra 0.1 and 1uF ceramic capacitors and 10uF or so tantalum electrolytics, all at 25V or higher, all to do power bypassing.

I've always found it useful to stock up on 3.3V and 5V voltage regulators at least. I usually keep some "adjustable" ones around as well. The classic LM78xx regulators are still pretty useful for general messing around. You can order what you really need later if you want something more compact or more efficient. But it's always nice to not have to wait for a DigiKey order just because you want to prototype a thing with a 3.3V microcontroller that plugs into your car's cigarette lighter auxiliary power jack.

I'm very into color coding my wiring, but find regular hookup wire to be too bulky for most board-to-board work in projects I'm working on. These days I buy long rolls of rainbow ribbon cable and tear it apart as necessary. It's nice to have a couple rolls of heavier black and red hookup wire for higher-current power leads.

I have a deep hatred of intermittent wire failures from flexing, and also get sick of perma-tangled spiderwebs that result from soldering both ends of things as I add things to a design. So I've started to favor crimped header connectors for wire-to-board connections to the point where I picked some up for the home lab. I like these Harwin M20s https://www.digikey.com/catalog/en/partgroup/m20-series/32875 ... easy to pull the contacts and re-configure or even re-use by lifting the plastic tabs with a jeweler's screwdriver. I'll still often solder at least one end of the cable directly to a board... usually solder to a sensor board and connectorize the microcontroller end or something like that.

I've had good luck crimping them with this cheap crimping tool: https://www.inventables.com/technologies/crimping-tool

Lots of small cable ties.

If you do a lot of soldering, a good third-(& fourth & fifth) hand system is great. I like the cutting-fluid-conduit style ones like this

https://www.amazon.com/Hobby-Creek-Helping-Hands-Soldering/dp/B010C504NK

I don't really have one at home right now. I built the ones I've got at work from parts from McMaster Carr.

> I originally was considering something like Lava Cables or maybe even the Evidence SIS kit, but those seem to be unreliable enough to give me pause. So, now I’m thinking that I’ll buy some plugs and cable and solder them myself (important note: at present I don’t know how to solder, but it doesn’t seem complicated, especially since it’s only cables).

Seriously, its way easier than you think. you can honestly learn how to solder going from absolutely zero experience to being able to solder cables in under a half hour. Id actually bet it takes less time then having to learn how to use the solderless solutions, which are a massive hassle.

Just last month I taught my friend how to solder and he went from knowing nothing to putting together a sweet diy keyboard in a single night.

Its also dead cheap to solder your own cables. Even the more "premium" cables come in under $1/ft and you can get pancake plugs off tayda.com for $0.50 each. Compare that to evidence charging 8$ per plug

so some quick math to maybe convince you some more

Evidence audio SIS plugs = $8 each.

pancake plugs = $0.50 each.

you need 48 plugs

848= $384 for the SIS plugs.

$0.5024= $24 for pancake plugs.

And then to add to that, the soldered plugs are going to be objectively more durable.

Also heres a little copy paste I made to help you know how little you'd actually need to spend to get started soldering. But if you have any other questions id be happy to help

if you don't plan on doing much soldering in the future and it's more of a one time thing, there's really no reason to get anything bore expensive than this. I spend easily 60 hours of solid soldering on the earlier version of this (same thing just without the leds) and I only ever replaced it because the tips were getting worn out (although you can replace the tips for cheap) and because I thought I deserved a more solid iron considering how much soldering I do.


if you do plan on doing lots of soldering in the future then I would recommend getting something other than a weller, they're honestly just one of those things that for years have been the industry standard but honestly have gone down hill. I've used a dozen different wellers, some old some new, some cheap some costing 300$ but none of them are really good. I, along with almost everyone in electronic repair industry like Luis Rossmann recommend a brang called hakko. I use atd absolutely love the hakko fx888d. It's really honestly just magic. It heats up to 700+ in under 30 seconds, with a live temperature readout (my old weller would take close to 15 minutes), atd the tips are really just magic, they just don't get corroded at all like every other brand I've used.



It's also worth mentioning for anyone new to soldering that the type of solder used makes a world of difference. What your going to want in rosin core, leaded solder (preferably 63/37 but 60/40 will work too). You want rosin core because it makes it a ton easier to not have to worry about flux, atd unless your doing really tiny electronic you won't need flux beyond the rosin core. You want leaded solder for a few reasons. First off, it melts at a way lower temperature (leaded solder melts at about 360f ish where lead free is closer to 460-480f, but saying that that's not at all the temps you wound use to actually solder at, it ranges from 400 - 700f depending on the application ). Leaded also has a way better surface tension, and melts more evenly, all this really just adds up to making it 100 times easier to work with, ESPECIALLY if you need to desolder anything.

Is it necessary to clean up flux? Almost never. Is it a good idea to do it anyway? I'd say so. Here's a good article about all things solder and flux to bring you up to speed.

Flux is SUPER carcinogenic, or so I've been lead to believe, and it also causes serious gastrointestinal issues if ingested, in even relatively small amounts. I generally try to leave all the circuit boards I work on clean of big globs of flux, but I'm no perfectionist. Flux is non-conductive, so don't worry if you leave a bunch behind or it looks like the flux might be bridging a connection. I oftentimes leave smaller flux contamination spots on the board, unless it's in a spot where I'd be likely to touch next time I'm handling the board.

Here's a pretty good soldering iron, the Hakko FX-888. It's more than enough iron to last you through all your projects in the foreseeable future, and it comes with extra tips and a tip cleaning canister. To be honest, though, it's pretty expensive, and I totally understand if it's out of your price range. Personally, I use a Chinese clone, which works extremely well, for what I paid for it.

I'd also recommend anyone working on anything with a soldering iron to get a set of helping hands. Finding one which isn't broken or of shit quality is a real crapshoot, but, once you have one that works, you'll wonder how you ever got by without one. Personally, I recommend spending the cash to get one with some sort of LED built in, but here's a link to a cheap and functional set of helping hands.

If you're going to be desoldering things often (or trying to make beautiful solder joints), you definitely want to get yourself some desoldering braid, which is just stranded copper wire filled with flux paste. When you put heat to the top of the braid and put the bottom of the braid on the component, the braid will wick excess solder from the component. Once you master using this stuff, it's a real boon for disassembly (or cleanup of solder blobs). You might also want to look into a desoldering pump, which is okay for some things, but not nearly as versatile as desoldering braid.

Last, but certainly not least, is having the right solder for the job. Personally, I use silver bearing solder, because I've been told it is more resistant to cold joints, and slightly more conductive. Here's a link to a spool of silver bearing solder, which I'd buy, were I in the market for a new spool.

One more link for you... When I was looking for a link to that Chinese clone soldering station, I stumbled on this DIY SMD soldering practice kit. Might be worth your time to invest in one and try your luck. For $2, it's a great way to go from soldering zero to soldering hero in a day or two. Also, check this page for more DIY kit ideas.

Let me know if you have any more questions! My inbox is always available, if you'd feel more comfortable PM'ing me questions, too. (That goes for anyone who needs a hand, not just /u/websurferathome)

there are about 5-6 other components that I could still replace in the horizontal linearity circuit and I will probably do this. I do think it will solve the issue but I will likely try because of how much effort and money I have invested into this set. I love the set other than the geometry problems and the geometry issue isn't really that noticeable in 3D games. I don't notice it at all when playing Super Mario 64 and N64 looks great on the JVC D201 set. Also, keep in mind that when you are dealing with geometry issues, you only need to focus on the horizontal and vertical linearity circuits which contain 20-30 aluminum electrolytic capacitors combined. Replacing capacitors isn't hard at all with the right tools. I did make sure to watch a ton of videos on how to solder and desolder and I bought my tools based on recommendations in Youtube videos and on several electronics forums.
 
I use this soldering iron and it works great, https://www.amazon.com/Hakko-FX888D-23BY-Digital-Soldering-Station/dp/B00ANZRT4M/ref=sr_1_3?keywords=hakko+soldering+iron&qid=1556333443&s=gateway&sr=8-3
 
I use this solder sucker and it is also great. You just have to make sure to push out the old solder with the pump after every 1-2 connections, https://www.amazon.com/Engineer-SS-02-Solder-Sucker/dp/B002MJMXD4/ref=sr_1_3?keywords=engineer+solder+sucker&qid=1556333566&s=gateway&sr=8-3
 
I recommend have a desoldering wick as backup as well. Use a no-clean solder wick of 2.0mm for general desoldering. As far as flux, flux paste is easier to use as it doesn't drip. The AMTECH NC-559-V2-TF no-clean tacky solder flux is good. Any no clean liquid flux from Kester or MG Chemicals will work fine as well. Definitely get some wire cutters for cutting solder and cutting component leads.
 
I use this solder (I recommend lead solder with a rosin core and also no clean) https://www.amazon.com/gp/product/B00068IJOU/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
 
Any time you work on a CRT, you need to discharge the anode cap. This is very easy to do with the proper tools. For example, you could use a flat head screwdriver and an alligator clip wire to do this. You connect one end to the screw driver, the other end to a ground point on the CRT chassis (i.e. the metal frame around the CRT), slide the screwdriver under the rubber anode cap with the CRT unplugged until you hit the metal connector in the metal. Rub the screwdriver on this metal connector for about 5 seconds and it will be discharged. Retrotech on Youtube has a video on how to do this. I wouldn't say you need $80 electrical gloves to do this but at least wear a rubber or leather glove or both and only use one hand. Retrotech actually has quite a few videos on how to work on CRTs.
 
Overall, doing basic things like replacing capacitors in CRTs isn't that hard, you just have to spend the time to educate yourself, be patient and it will click. If you have any questions, just ask me or anyone else on here. If you ever work on any power circuit capacitors, make sure to discharge them with a high wattage and ohm rated resistor but using insulated pliers to hold the resistor legs to the capacitor legs for about 5 seconds to discharge the cap before you remove it.

If you can't get it with a Q-tip, it's nothing to worry about. Grab yourself a soldering iron on Amazon, as well as some quality solder and flux. I will link some in an edit to this comment in a few minutes. Also, screw everyone else in this thread, that is damn near the perfect amount of thermal paste.

EDIT: Here are my recommendations and reasons!

​

SOLDERING IRONS:

Cheapo soldering iron:

​

https://www.amazon.com/GLE2016-Soldering-Adjustable-Temperature-Different/dp/B01N413T8U/ref=sr_1_5?keywords=soldering+iron&qid=1554943755&s=gateway&sr=8-5

​

This one will do you some good for the quick fix, although I can't speak to the longevity of the iron or its ability to melt some of the higher temperature solders that factories use.

​

More expensive (but WAAAAAAY BETTER) iron:

​

https://www.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC/ref=sr_1_6?keywords=soldering+iron&qid=1554943755&s=gateway&sr=8-6

​

This is a great soldering iron if you think electronics is something you'd like to get into. Quality replaceable tips are available, and it has a stand and comes with a cleaning sponge. I've used these, and absolutely love them. Honestly though, if this is going to be one of very few times you solder, just go for the cheap one.

​

​

​

SOLDER:

​

The cheap iron comes with some solder, and honestly you can probably get away with that for this one repair. If you decide to get the more premium iron though, here is some good solder:

​

https://www.amazon.com/Mudder-Solder-Electrical-Soldering-0-22lbs/dp/B01B61TWGY/ref=sr_1_5?keywords=solder&qid=1554944194&s=gateway&sr=8-5

​

OR (I've never used this particular solder but MG chemicals is a great brand)

​

https://www.amazon.com/MG-Chemicals-Leaded-Solder-Diameter/dp/B004258YDE/ref=sr_1_2_sspa?keywords=mg+chemicals+no+clean&qid=1554944408&s=gateway&sr=8-2-spons&psc=1

​

I usually stick to smaller diameter solders because you have a lot more control over how much you're putting onto a joint. This stuff is good, but really you just need to make sure it's lead solder because it melts a lot easier and is easier for beginners to work with.

​

​

​

FLUX:

​

If you want your joints to form and form well, you need some flux. At least coming from me, this is mandatory. Here's some good no-clean flux that you can use that will mostly evaporate off and shouldn't be much fuss to clean.

​

https://www.amazon.com/Paste-10-milliliters-Pneumatic-Dispenser/dp/B00425FUW2/ref=sr_1_3?keywords=mg+chemicals+no+clean&qid=1554944408&s=gateway&sr=8-3

​

​

​

TUTORIAL:

Although kind of slow, here's a pretty good soldering guide. This relates more to soldering electrical components, but most of the lessons remain the same.

https://www.youtube.com/watch?v=IpkkfK937mU

​

Best of luck!

Is Preonic worth the investment?

I have a Planck rather than a Preonic but OLKB designs sturdy and reliable boards that are also very interesting.

I honestly think the Planck is like twitter. Having a very low word (key) count makes people more creative in how they express themselves. The Preonic is more like tumbler where more things can be done more easily.

Moving keys to other layers is fine due to the extra thumbable keys on the bottom row. The Preonic doesn't require as many layers because it has so many more keys, so the extra thumb keys aren't really necessary.

That said, it's a nice compromise.

Is it a good build for a beginner?

It's the same difficulty as any other keyboard build that has PCB components soldered on. All you have to do is add switches and through-hole solder them. It's definitely a fine way to learn to solder as long as you follow a few rules.

Most keyboard kits come this way with the exception of those like the Lets Split which you have to solder diodes and a promicro onto also.

The only thing More difficult is getting a PCB printed and buying diodes, resisters, and chips from DigiKey and then using a heat gun or oven to cook all the little things on.

What is a good soldering station?

Cheap ones will work fine. People around here seem to like the Hakko 888d which is what I use. The cheaper ones like this will also work fine. The extra $80 doesn't change much about how you work. Turn on the iron, heat stuff, sponge occasionally, don't touch it to your skin, then put it away safely.

Soldering rules for beginners

1. Don't hold the heat on any part for more than 5 seconds. If it starts looking like a mess, go solder other parts and let things cool off before coming back to fix it. Don't freak out about the speed, just be deliberate and have things ready before you start applying heat
   
2. Use leaded solder because it's much easier to melt and manipulate
   
3. Use rosin core, no clean solder so you don't have to futz around with flux or flux cleaner
   
4. Put the iron down when you're not using it. It is shaped like a pencil and we humans like to tuck those between fingers while manipulating things. Do not do this.
   
   There are a lot of little things to do to maximize soldering experience. You'll figure these out over time. I thing this short list is enough to keep your board intact and blood in your body.

I got an Eachine 250 racer about a month ago. It has been a lot of fun, but there are a lot of details. My next racer will probably be a smaller/lighter 180 frame.

For FPV goggles I have three ideas. One, is get the status quo Fatshark goggles at whatever level you can afford. Two, get the HeadPlay HD goggles I got. Three, get the Avegant Glyph, which has the really nice feature of letting you pop them up and down without a band. I do really like my HeadPlay HDs, but they are big and bulky. I haven't perfected how to adjust the straps to get them to stay on my head well.

Arms, managed to break one without breaking a prop.

http://www.amazon.com/gp/aw/d/B016Y5U1JO/ref=ya_aw_od_pi?ie=UTF8&psc=1

Capacitors, they pop off very easily. I lost a capacitor at the same time I broke an arm. Or a hot glue gun, I Highly recommend putting hot glue over the caps next to each arm to help avoid the loss in the first place. You want a low temperature hot glue gun to not melt any plastic or traces. I consider the capacitor issue a design defect, but you can work around it with hot glue. The original revision seems to have lacked the capacitors, from pictures I have seen online.

Capacitors for Eachine 250 racer:
http://www.amazon.com/gp/aw/d/B00W8YYMZA/ref=ya_aw_od_pi?ie=UTF8&psc=1

Youtube video exampling how to solder them:
https://www.youtube.com/watch?v=sLYVZUpL0K0

Get a Taranis X9D Plus. It is a great transmitter. Also get a X4R-SB receiver, and use SBUS. The D4R won't let you control the lights too, because it can't do PPM and PWM at the same time. You can control them with the X4R-SB, SBUS+PWM. SBUS has great latency, 5-10ms. I was recently talking to a sponsored racer who told me that PPM, which is supposed to be 27ms with the D4R, is really more like 100ms. It averages the four last frames together. This link includes a case and X8R, which I think will work as well as the X4R, but you should do the research. http://www.amazon.com/gp/aw/d/B014IYSXL6/ref=mp_s_a_1_5

To do SBUS+PWM, requires a special bind procedure. You want channels 1-8 as SBUS, and 9+ as PWM. The most relevant part is "jump S1&S3: SBUS, 9, 10, 11 or jump S2&S3: SBUS, 9, 10, 11 (No telemetry)" Here is a link that talks about it.

http://www.frsky-rc.com/BBS/viewtopic.php?f=4&t=6793

Small tie wraps like the ones already on the arms to hold the ESCs. You break an arm, and you will need to replace the tie wrap.

Soldering iron, solder, etc, because you have to desolder the ESC from the motor to replace an arm, and then resolder it.

http://www.amazon.com/gp/aw/d/B000BRC2XU/ref=ya_aw_od_pi?ie=UTF8&psc=1

Qtips and rubbing alcohol for cleaning. Mix the alcohol 50/50 with water. The flying field was muddy after lots of rain.

Carrying case of some kind. You don't want it banged around in transport, and same with the transmitter. It is best to get the X9D with the case, because people price gouge on the case stand alone.

http://www.amazon.com/gp/aw/d/B01ABQS7YI/ref=ya_aw_od_pi?ie=UTF8&psc=1

Batteries, you can burn through them very fast. But watch out for their height. I bought some of the new "Graphene" 4S batteries, and they are really too tall to fit. Some people remove the back LEDs to make battery installation easier.

Battery charging/carrying bags to help with uncontrolled fires started by batteries. I have two, one for charging, and one for carrying.

http://www.amazon.com/gp/aw/d/B005HTH78W/ref=ya_aw_od_pi?ie=UTF8&psc=1

A battery charger if you want to use 4S batteries. The included charger is 2S/3S only. I have a Hi-tech X1 which will only charge one battery at a time. You can also get the X4 which will do four at once.

Battery charger for 4S batteries:

http://www.amazon.com/gp/aw/d/B005LH3392/ref=ya_aw_od_pi?ie=UTF8&psc=1

XT60 banana plug cable for charging with the above charger:

http://www.amazon.com/gp/aw/d/B00XBSBYCG/ref=ya_aw_od_pi?ie=UTF8&psc=1

A V shaped antenna mount to get the receiver antennas up in the air. When over head the carbon fiber body blocks the signal well.

http://www.amazon.com/gp/aw/d/B00WV04P62/ref=ya_aw_od_pi?ie=UTF8&psc=1

A voltage monitor so you know to land when your battery voltage is low. The video signal includes the battery voltage as part of the OSD, but I prefer LoS while learning to fly. It lets me keep an eye on where I am in relation to trees. On the other hand I have yet to find a good place to mount a voltage monitor. With the length of the balance cable on batteries you are likely going to need a balance cable extension for 3S and another for 4S.

Voltage monitor:

http://www.amazon.com/gp/aw/d/B00EXPPF80/ref=ya_aw_od_pi?ie=UTF8&psc=1

3S balance cable extension:

http://www.amazon.com/gp/aw/d/B00XP4IO88/ref=ya_aw_od_pi?ie=UTF8&psc=1

4S balance cable extension:

http://www.amazon.com/gp/aw/d/B00JBP1RGG/ref=ya_aw_od_pi?ie=UTF8&psc=1

Double sided tape to mount things on the top of the body, like the antenna mount and receiver.

http://www.amazon.com/gp/aw/d/B009NP1JQC/ref=ya_aw_od_pi?ie=UTF8&psc=1

Small x-acto knife to help remove the double sided tape.

Electrical tape to tape down wires for lights and receiver.

Size 2.0 hex wrench for the frame screws. It will be needed to replace arms.

Scale that can measure grams. You want to knowing and control weight.

http://www.amazon.com/gp/aw/d/B010HKEDPK/ref=ya_aw_od_pi?ie=UTF8&psc=1

Sunglasses to avoid problems seeing on sunny days. Lets say you are flying LoS, and look into the direction of the sun. You can't see the quad well enough to control it, because of glare from the sun.

ESC flashing adapters to change/upgrade the firmware. I am not sure these are the right ones for the ESCs on the Eachine. I think they are, but I haven't tried it yet.

Atmel socket flashing tool:

http://www.amazon.com/gp/aw/d/B00V2W467I/ref=ya_aw_od_pi?ie=UTF8&psc=1

Atmel USB programmer:

http://www.amazon.com/gp/aw/d/B0051SRZWC/ref=ya_aw_od_pi?ie=UTF8&psc=1

USB cable to use with transmitters and simulators. It is best to learn the basics in a sim, instead of replacing lots of parts.

USB cable for simulators:

https://www.amazon.com/gp/aw/d/B00DFDTU9G/ref=ya_aw_od_pi?ie=UTF8&psc=1

Old post of mine on learning in a simulator:

https://www.reddit.com/r/Multicopter/comments/3zr8o0/cheap_fpv_acro_simulator_with_real_transmitters/

Be sure to set a fail-safe, which is very easy with the Taranis. I had a fly away with my first Eachine, because of a defective Spektrum DX6 and lack of fail-safe. After that I switched to the Taranis, which doesn't cost much more and has way more capacity.

I've been looking into this space (best medium-cost maker/builder/fab tools) over the past couple of months, and here are my recommendations so far...

• CNC Mill (router) - For doing wood, plastic, and some light metal work, the Shapeoko 3 stands above the rest. It runs around $1.2k with a router included and can cut 16"x16"x3". You'll still need mill/router bits and materials, but pretty awesome for the price range. Note that they also just started selling larger versions (goes up to 33"x33"x3") for a few hundred dollars more. To move up to the next professional level but still on a budget, I'd consider building your own via CNCRouterParts Pro Kits (48”x48”x12”, $8k total).
  
  
• 3D Printer - The LulzBot TAZ 5 stands above the rest because of the range of materials it can print (with a special high temperature hot end) and its build area (11.7”x10.8”x9.8”). It's recently been reviewed by Make as the "Best Overall 3D Printer" which is a pretty high endorsement. It runs a little expensive ($2.2k) but looks like it's one of the best bets if you're looking to get into 3D printing.
  
  
• Lathe - You can get a mini lathe (7”x16”, $1.3k) in the price range you're considering, and while it may be a bit too speciality and manual, they're a great tool to have in your workshop. Especially if you like making round things.
  
  
• Laser Cutter - To get a decent laser cutter (not just engraving, but actually cutting materials) that won't break down, catch fire, release noxious fumes, or potentially blind you is currently around $4k minimum. There are a lot of cheap "eBay" laser cutters out there, but when you start to add up everything and weigh the risks they aren't really all that much cheaper. The two stand out models I've been considering are the FullSpectrum (40W, $6k) and the "coming soon" Glowforge Pro (45W, $4.8k).
  
  
• Electronics - You didn't mention this, but if you're looking at getting your hands dirty making things, electronics is now a pretty crucial component to support. The big ticket items (like an oscilloscope) are now a lot more reasonable than they were even 5 years ago and sites like SparkFun carry a lot of electronic components and tutorials that make it easy to get started even if you don't have much background in circuitry (yet!). My short list would include: a Rigol 50MHz, 4Chan, color disp, 4 probe oscilloscope ($450), a nice Weller soldering iron ($320), a soldering fume extractor ($70), some helping hands ($10), a Siglent signal generator ($360), and some nice boxes to keep your parts sorted ($20).
  
  Now go make some awesome things!
  

Well to replace the battery you'll need to open the cart, carefully desolder the old battery, and solder in the new one. It's fairly straightforward and easy, but you can go look up a youtube video for a walkthrough. In theory you can tape in a new untabbed one in, but going with the original design/intention is preferable and won't come loose and lose your save if done properly. However, you'll need the following:

• special driver/bit to open the cartridge (can also use fine tipped pliers to grip the screw and put it in/take it out, but you may scratch up the top of the screw)
  
• replacement lithium coin cell battery with solder tabs (probably a CR2025)
  
• a soldering iron or station
  
• solder, probably 60/40 Sn-Pb as mentioned earlier
  
  optional:
  
• solder wick (copper braid) for removing old solder, it makes putting the new battery in a little easier if you can work with new solder and a cleaner point to solder to
  
  I got my batteries and screwdriver from a online store that sells gameboy stuff:
  https://www.mortoffgames.com/cr2025-coin-cell-battery-with-tabs-panasonic-
  https://www.mortoffgames.com/gameboy-color/repair-and-replacement-parts35/game-repair-parts39/38mm-security-screw-driver
  
  From Amazon:
  https://www.amazon.com/Steel-3-8mm-Screwdriver-Security-Nintendo/dp/B000F8GWH2/ (3.8mm security bit)
  https://www.amazon.com/Super-Nintendo-Genesis-Master-System-Advance/dp/B00ES2B0CI/ (CR2025 w/solder tabs)
  https://www.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC
  https://www.amazon.com/WYCTIN-Solder-Electrical-Solderding-0-11lbs/dp/B071G1J3W6/
  ^ lots of options, this is close to what I use --- 60/40 Sn-Pb, rosin core, 0.6mm diameter -- it don't think it's that much solder for the price, but I probably paid at least twice that at least and I've done lots of stuff and I still have way more than I needed. You can probably use a smaller diameter for this specific job, but that size is easy to hold.
  
  It seems like a lot of money, but you got a pretty good deal on the unit and game. They can go for $20-30 and $12-18 respectively. Also, the screwdriver/bit and soldering iron are one-time investments in being able to do it again later and also do other soldering work.
  
  If you don't mind making separate purchases the other source I mentioned has way better battery prices and their screwdriver is a bit cheaper and has a handle, I have one myself and it works fine. In general though I recommend going for the best quality one just so you don't have cheap, crappy tools. Sometimes that means you pay a little one more, and sometimes pricing is about the same.
  
  
  

This one on Amazon seems to have pretty good reviews. I'd recommend getting a stand like this to go with it for safety reasons. (I decided to solder without mine a few weeks ago, and wouldn't you know it, the one time I decide I don't need the stand, I burn myself!)

You can easily spend a lot more on irons, and if you start doing a lot more soldering you may want to make a bigger investment. A lot of people really like the Hakko FX888D, but I personally prefer the Weller WTCPT-60 because I don't like fussing with knobs. (Despite not having a knob, the Weller actually does have very precise temperature control, but depending on what temperature you want you have to buy different tips, which isn't worth the hassle for most people. I use only one kind of solder so it doesn't matter for me, but I digress.)

I've never found any tutorials I really like, and my advice is to just get busy! You'll make a lot of mistakes and do a lot of projects slowly before you get good, and I don't think there's a tutorial out there that will let you skip that. To help you stay pointed in the right direction, here are a few things I look for in a good solder joint:

• A clean, consistent meniscus around the parts being soldered. If I'm tinning stranded wire, then I want to be able to see the contours of the strands underneath the solder once it's cooled, while still using enough solder to get good penetration. Big gobs of solder all over the place look tacky, can cause shorts, and can indicate the next problem:
  
• "Cold" solder joints. By this I mean that the conductors you're soldering together weren't hot enough when the solder melted, and so the solder didn't stick. Solder on "cold" joints will often (but not always) have a frosty appearance, and will usually bead up instead of forming a meniscus like I described earlier. To make sure your joints aren't cold, use the iron to heat the joint, then touch the solder to the joint (rather than the iron), to melt it. If the conductor is hot enough to melt solder by itself, you can be sure you're joints won't be cold. (Usually you have to melt a little gob of solder onto the iron first to get the heat to conduct into the joint. This is a trick you can only get good at through practice.)
  
  There are a few intuition issues you should be aware of that I've observed while teaching students to solder. For instance, most of the stuff you'll be soldering is so small that it will be "cold" (as in "too cold to melt solder") the instant you pull the iron away, and cool enough to touch within seconds. Try it if you don't believe me. The part will only stay hot as long as the iron is touching it. You'd be surprised how many people can't get their head around this.
  
  Also, oxygen is your enemy. The longer the part is hot, the more oxidized the surface will become and the harder it will be for solder to stick. This is true even when the joint is hot, but not hot enough to melt solder! So once the iron contacts the work, you have to be expedient. Most joints can be finished in 5 seconds or less, and if you're holding the iron on there for 10 seconds or more but the solder still isn't melting, stop and reexamine what you're doing. You may want to get some fine-grit sandpaper to clean the conductors off before you start again.
  
  Keeping oxygen out of your solder joint is the job of flux, and like /u/avialex (edit: fixed) said it's very helpful (provided everything is relatively clean to begin with). But again it's a balancing act. If you use too much flux you'll make a mess, and raw flux is slightly corrosive and can be very difficult to clean off your work.
  
  There are lots of other tricks you'll learn through practice too. I guess that's where tutorials might come in handy. You'll probably learn to splice wires (probably the most difficult thing to do with a soldering iron) much more quickly from someone with experience on Youtube than struggling through it 20,000 times yourself, doing it a harder way because you didn't know any better.
  
  At the same time though, there's no substitute for practice. This went on a lot longer than I intended, but I think now you have plenty of information to keep in mind as you get started. Good luck and happy soldering!

Nice! It is rewarding knowing that you can repair and modify your guitar's wiring as you please, just gotta break the seal and do it that first time. As with anything, practice makes perfect. My solder jobs looked pretty terrible and messy the first several times I tried it, but the more I do it the cleaner and more professional they look. Youtube instruction videos are super helpful as well, and having a decent iron that's at least 40 watts makes things much easier (doesn't have to be too expensive, I use one of these and am very happy with it).

Also, Seth Lovers are a great call. I have them in my Les Paul and they're the definition of the classic PAF sound, lots of snap and clarity but also totally lush and warm and punchy. Perfect for pretty much anything short of metal imo.

I run this instead of a Dremel brand tool. I have had a couple Dremels die on me over the years, so I tried this one and it has lasted 4 years so far! I also got a lot of my bits from harbor freight. I use the cuttoff wheels (ALWAYS WEAR FACE PROTECTION WITH THESE), Sanding Drums, and grinding stones the most. Use the cutoff for cutting out large swaths of material, sanding drums for tighter areas, and grinding stones to debur and smooth it all out. Most work that needs a dremel can be done with hand tools for better control. Coping saw, files, and flush cutters can go a long way. A lot of the "pros" don't use Dremels because they can jump out of control and hit a part of the blaster you planned on leaving stock and leaving a huge gash.

As for soldering Irons, I've heard wonderful things about this model, but cheaper models will work fine. TBH, I'd grab something in the $10 range and see if he sticks with the hobby. Maybe for christmas you can get him a nicer one if he's still going at it. I use a super duper old school Weller soldering station, so really anything will work. The issue you'll get with the cheaper soldering irons is the tips will tend to not last long and the heating element might crap out after a few months. Don't go cheaper than $10 here as some of them are meant for wood engraving, not soldering and wont get hot enough to melt solder. Any size solder is fine. I personally use lead/tin solder and just avoid breathing fumes as well as wash my hands when I'm done modding. Lead solder is MUCH easier to work with and requires less heat. Look for "Rosin Core solder" as it's easier to work with as it has flux in the center of the solder.

Good flush cutters, hobby knife, wire strippers, heatshrink, wire, loctite, etc are all valuable modding supplies. We sell some on our shop (shameless plug). I would recommend for plastic to plastic bonds he use Devcon Plastic Welder (make sure it contains Methyl Methacrylate as this acts as a solvent weld to bond the plastics together chemically instead of a weak adhesive grip like putty). Putty should be used as a filler material. I use two different putties. Free form Air for large amounts of gap fill, it is 6 times less dense than normal putty so it wont make the blaster weight 8 pounds when done. It is VERY easy to sand, but sometimes requires a thin layer of bondo over top of it to leave a perfect finish. I also use Apoxie Sculpt which is a direct replacement for normal putty for gap filling purposes. It's MUCH easier to sand than JB Weld putty, and leaves a nice smooth finish when sanded down.

Speaking of sandpaper, get various grades of sandpaper from 100 down to 600 grit (I go as far as 1000 if I want a gloss sheen on something).

Other than all of that, the tools I have on my bench that I would hate to mod without now are: Helping hands (for soldering), various different sizes of needle nose pliers, numerous sizes of small to medium screwdrivers, silicone lubricant, hot glue (for securing wires inside the shell), Electric Screwdriver, and various tweezers.

That's actually a good ideal TBH as you run the risk of damaging the PCB way more than damaging the switches should things go south. Then if you end up lifting a few pads in the de-soldering or soldering process, you can always just jump them as long as you don't burn too many up. Worst case you fry a $20 KB which would suck, but not be a huge waste or anything for the experience you with de-soldering/soldering TBH.

I would clip & lube the stabilizers while you have it all apart, I'm sure those could use the help from that bad. Also most likely you will need to de-solder & remove the LEDs to get the original switches out so you can get enough in one color to cover the whole board & solve the rainbow LED problem while your at it too!

A few tips though, the lead free solder used on these mass produced boards has a pretty high melting point & is tough to get to flow. I highly recommend getting a cheap de-soldering iron like this or this for doing it, also solder wick is a must too. Then any joints that don't come completely clean on the first try, re-solder with leaded iron & repeat the de-soldering process on them. That usually helps to get any remaining lead free solder to move.

The other thing is to get yourself a temp controlled soldering iron. If you plan on getting into building boards I suggest something fairly decent like the Hakko FX888D, it's a little pricey but well worth it if you will using it alot. If you plan on only doing a few projects here & there, you could get away something a little cheaper like this. Anyways GL with the project & I hope to see a success post sooner than later! :)

Has he applied for any jobs yet? I was given one of those leather pads with paper inside and a holder for resumes (something like this) except it was from my undergrad university with their emblem. Definitely gives you some confidence for interviews and recruiting sessions. Also you can get him some nice resume paper to go with it. That lasted me for years.

I also enjoyed having one or two of these demotivational posters in my room. Depends on his humor and if he has barren walls like I did.

If you know more details about which raspberry pi he has, you could get some shield extensions. These are boards that expand its capabilities. There are also newer boards with better specs. Also with two boards you can of course make them talk to each other ;)

Depends on his area of interest and your budget, but you could get him some kind of [introductory FPGA kit] (http://store.digilentinc.com/fpga-programmable-logic/) or DE0-Nano.

Tools... so many tools he might be interested in. USB logic analyzers are so cheap these days and go well with hobby boards. Again not sure your budget, so you can go all sorts of ranges here (Open Workbench Logic Sniffer or scanaplus or Saleae Logic 8 or a china clone of Saleae Logic 8). Saleae or the knockoff I think are the better options for the software compatibility. He may be in need of a soldering iron or a multimeter.

Something else unique, you could get him a "gift card" (they don't really sell them) or an IOU to a PCB printing service. Ask him to design his own board and you'll pay $X of the service. You'll want to make sure he knows the price structure on the website because they charge per square inch and it depends on his design how many layers he may need. He makes the schematic and they will print some circuit boards for him. They won't mount the parts, just do the schematic and he would have to hand solder the components.

If he likes old videogames you could get him some old school USB controllers and tell him to install lakka on his rasberry pi, or just get him a new Raspberry Pi3 to dedicate it as an old-school console emulator. It is quite impressive how many consoles they have emulated.

And back to more tools... more micro screwdriver bits than you would actually need. You can get him a starter pack of resistors, capacitors, and other assorted electronics sparkfun. There are also so many buttons, switches, LED screen displays, etc. that he probably wouldn't want to buy on his own. Maybe you could get a container with an assortment of circuit components (resistors, capacitors, transistors, and other sensors). Careful! This can add up real quick. All types of sensors exist... ultrasonic rangefinder, stress, photocell, temperature, etc. etc. endless!.

This is my iron. There are many like it, but this one is mine. It's not a great iron, it's a good enough iron, and you can get replacement tips pretty cheap. (I'm actually wanting to upgrade to a $150 Weller, but my iron still works fine. I want better heat control and thermal capacity, but this is one of those "if you can't explain why you need it, you don't need it yet" things.) I also bought this tip cleaner on the same order apparently, I prefer it to a sponge but it's not necessary.

This is the solder I bought most recently. It's honestly a little on the thick side, and multi-core would be better, but it was cheap and works fine. Without the rosin, you'd need flux; they etch the metal to remove the oxide layer that naturally forms and would inhibit a good joint. Thin solder melts faster and gives you more control over how much you apply.

There's other stuff that isn't strictly necessary, but is useful. I have a heat antistatic may on my work bench, and a cheap fume extractor set up behind it; I won't bother linking it because it doesn't have any kind of filter in it. The rosin smoke and the lead are both kinda toxic, so a well-ventilated area and/or a good fume extractor are important. I also keep flux paste, desoldering wick, a solder sucker, and a set of helping hands on my workbench, but I use all that stuff because I do a fair bit of electronics work, YMMV.

For references, Dave of EEVBlog fame has a three part tutorial on soldering which covers all the bases pretty well. He'll also leave you saying "sohldah" instead of "sodder," which is a fun way to annoy American EEs.

Edit: This is my workbench, for reference since I'm in that room right now. There's heat shrink on the helping hands, a trick I straight up stole from /u/bulbufet. It keeps the alligator clips from digging into wires, though the heat shrink has to be replaced periodically as the teeth will eventually work their way through it. And if you don't want to slap together a solder holder out of MDF, you can buy them, but where's the fun in that?

I've started to get into electronics myself, and I can say that soldering is easy, but you need the right tools for the job.
You'll need an adjustable temperature soldering iron and 1/2 milimeter iron/lead solder as the bare minimum.

I suggest grabbing some tip tinner, solder wick & vacuum, and some cheap boards to practice soldering.

This video shows how to do the actual soldering, while this video covers the tools you'll need and explains their use. These videos are made by EEV Blog and explain soldering in GREAT detail, which is how I learned to do it.



As far as making actual circuits, you have to have an idea AND parts to fulfill your idea. The Arduino UNO is a great way to program and test circuits. It's essentially a small comptuer designed to repeat whatver task you give it over and over. Alternatively, there's the Raspberry Pi, which comes in a few different models. The difference between the Pi and the Arduino is that the Pi is essentially a mini computer. You can literally hook it up to a monitor via hdmi and slam an operating system into it.

Both boards typically come in kits like this one for the Ardunio, or this one for the Raspberry Pi. The Ardunio kits with come with a lot of peripherals, like sensors and LEDs that actually do things, while you'll have to invest more with a Raspberry Pi. These kits come with detailed instructions, code you can copy and paste, and are a great way to learn how circuitry works, and is exactly what I'm doing right now. I'm no expert by any stretch of the imagination, I've just done a decent amount of research to find out what's what.

There are two ways to hook up circuits - temporarily and (somewhat) permanently. Breadboards are used to prototype circuits without having to solder anything, typically using these wires to link different parts of the circuits together. Soldering components to those green boards I linked earlier is what you'd do when you have your circuit up and running and want to move it to something more permanent. I say "more" permanent because you can usually de-solder stuff if you needed a component for something.

Adafruit has a decently sized library of projects you can try. They often sell stuff in kits where you get everything you need to make something -- for example, this DIY MIDI controller.

Sparkfun has a great series of articles that explain the very basics of circuits and electricity

Hopefully I've explained everything enough so that you can venture off on your own. Feel free to ask questions!

Everyone here is recommending you buy a soldering station - which is 3 times the cost of the full kit you linked which is absurd. The Hakko 888 is fantastic, but not what should be recommended in this scenario.

​

Honestly what you linked is likely crap and will probably frustrate you away from the hobby. If you get something with easy-to-buy interchangeable tips, it will help you a lot. Something like: https://www.amazon.com/dp/B000AS28UC/ may be a bit better of a deal and will be fine for learning. Also grab yourself some well-reviewed solder (rosin-core is fine), a cheap solder wick, cheap solder sucker, and a flux pen (flux will only be necessary if you are re-working - something you may do a lot when you start).

​

If you are looking for a cheap multimeter as well, anything will likely be good enough. Buy whatever has a feature set you think you need. Just note, that I wouldn't recommend measuring anything like mains AC with a cheap meter. Stick to low voltage ( < 50V) DC and you'l be fine. One of my favorite meters is the VC921 pocket DMM. It can be had for ~$10 and is accurate enough for me with a good feature set. Just note that it doesn't do current measurements. If you think you may get into electronics long term I recommend investing a nice meter. Fluke is the go-to brand-name, but there are many who will work just as well. Fluke 101 is ~$40 and will do everything besides current readings. If you want current, I recommend stepping up to the Fluke 107.

​

Also not a fan of all of the tools in that kit you linked. A lot seem un-necessary or extra cheap. These are expensive, but Adafruit and Sparkfun are great and reliable sources for hobbyists and have similar kits:

​

https://www.adafruit.com/product/136

https://www.sparkfun.com/products/14681

I'm in the process of building my first FPV drone with my 11 year old son. Tools I owned or have purchased for this are:

A set of small screw drivers. I found a set in the bargain bin at NAPA Auto that had straight, philips, a few hex, a few sockets.

A decent electronics soldering station. Not the gun. I have a digital Weller that is easy to control, but the analog is just as good for these purposes.

A third hand. There are many different kinds. I got a cheap $5 one at Harbor Freight. Not great, but does the job.

Solder, de-soldering wick, flux (maybe)

Depending on where you're doing your work, might want an air-filter or fan.

A magnifying lamp is helpful but not necessary.

An assortment of board stand-offs/spacers is handy.

A good small pair of wire snips.

Wire stripper

A digital multimeter is not a bad idea.

Those are all the major tools you might need. Plus all the drone parts. batteries/charger. Radio/receiver. Camera/receiver(goggles or screen).

In short, it's a lot of stuff. The drone parts end up being the least expensive part, honestly.

Above links are just examples, not necessarily endorsements.

You mentioned you're on a budget, which I totally understand. Building is not the cheapest route, but it's been a lot of fun so far. People who've done it for a while tend to forget the cost of tools. Once you've built one, subsequent drones are relatively cheap. You can re-use batteries, the charger, most decent radios, even the receiver.

If you're not in a hurry, Bangood is a good source for cheap(er) parts. You're on your own for support, usually, but there's lots of help out there.

Ok, so there are a lot of things I'd probably change :)

​

Motors - SabotageRC Booty 2306-2300kV, they're cheaper and significantly higher quality than the DYS you're looking at (they are made by DYS, as well, but with much higher quality components and build quality)

​

ESC - beware Racerstar. Some things they OEM and you get a good product for a good price, but others you get significant drops in quality. I would pay a few cents more apiece and get Spedix ES-20 Lite ESCs.

​

VTX - the one you selected is decent, but your soldering skills need to be up to par, the wires come undone from the VTX extremely easily and are incredibly difficult to reattach. I would recommend a few dollars more to get an AKK VTX with either larger pads or a connector.

​

VTX antennas - There are better ones out there. Lumenier Axii is one of the best and most durable (and significantly lighter), pagoda antennas being slightly better in some regards but more fragile.

​

Radio - The Turnigy Evolution is about the same price now and is a better choice than the FS-i6. Still uses the Flysky AFHDS2A protocol, so it will work with the receiver you selected (and there are now others that are good, as well). If the phonebook style radio appeals to you, then the i6 is the only cheap choice, but keep in mind it is a CHEAP radio, not an inexpensive one.

​

Wire - I would suggest ordering some 14, 16, 18, 20, 22, 24, 26, 28 gauge wire from Hobbyking (as much as they suck, they're the only place that sells lengths of wire inexpensively). Getting 1m of each wire in both black and red should only be 10-15 bucks IIRC.

​

Power supply for charger - get a supply that is at least 19v and 200 watts, like this: https://www.amazon.com/MEAN-WELL-LRS-200-24-211-2W-Switchable/dp/B00YMA7I7C/ it is a few dollars more, but you can also run your charger at its full output, which will come in handy for charging your batteries in a timely fashion.

​

Soldering iron - get a quality one, you're going to need it. https://www.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC/

​

You should also get some no-clean flux: https://www.amazon.com/MG-Chemicals-milliliters-Pneumatic-Dispensing/dp/B00425FUW2/

​

Decent solder: https://www.amazon.com/MAIYUM-63-37-solder-electrical-soldering/dp/B076QF1Y85/

​

And a tip cleaner: https://www.amazon.com/Hakko-599B-02-Wire-type-soldering-cleaner/dp/B00FZPGDLA/

​

That should get you well on your way - still on a budget, but you'll hate yourself WAY less when you go to build it and have decent equipment. :)

Sorry for your loss, congrats on the decision. I'd start with Dave Jones' video on how to build an electronics bench.

You definitely need a multimeter, but I only have a clearance-bin radioshack one, so maybe get someone else's advice... I can suggest getting an adjustable soldering station and a big spool of fine solder. Also get a couple spools of 22-26 AWG wire, stranded and solid core.

For audio stuff, nothing beats an analog oscilloscope. It's super handy for testing and looks awesome when the synth is fired up. Get on ebay and look for estate-sale type stuff near you to save on shipping.

When you're assembling PCBs, the most critical tool is a nice circuit board holder. Colored alligator clip leads are really handy for testing stuff before you assemble it.

If you're doing your own panels or etching boards or whatever, you'll definitely need a drill. The new 14.4v Makita stuff is my favorite, but get what you like. Ditto for a rotary tool/dremel. Everyone lusts after the wiha screwdrivers but any old jeweler's toolkit should suffice.

What else? Automatic wire strippers, flush cutters, center punch, desoldering braid, heat shrink, etchant tubs, ferric chloride, latex gloves etc etc. Depends how DIY you want to get. Good luck!

As stated, 99% chance it's blown caps (capacitors). It's a very common problem with today's cheaply made TVs and computers.



The good news is that they are actually pretty easy to diagnose and replace. There are tons of video tutorials that will walk you through it. It only takes about 20 minutes maybe to do the whole thing for about $35 - $40 bucks. Then if it ever happens again with another TV, it's only about $15 each time after. So, instead of throwing out that TV, you can repair it for $40; so not bad!



First, you want to diagnose if this is the problem. Lay your TV down on a flat surface and take off the back, usually just need a screwdriver. Look at the capacitors (which look like very short AA batteries) and if they are blown, the tops will be leaking, bulging, and/or oozing. There are TONS of Google images to compare against.

• Google images for bad/blown capacitors
  
  
  
  If it is the caps, all you need are 2 things:
  
  
• A replacement capacitor kit, which you can find on-line for your tv make and model. They run about $15 bucks give or take for the whole set. They will sell you a kit that contains all the capacitors needed for your specific make and model. They come in various sizes and powers, so you want to buy the correct ones for your TV.
  
  
• A soldering iron. You can get a small decent one from Amazon for about $20 bucks. A good investment because you will use it again and again on various TVs, etc.
  
  
  
  
  The videos will walk you through how to do it, including use the soldering iron. It's pretty easy. For what it's worth, I am a woman, with no electronic background and have now replaced and fixed 3 TVs that I've had this happen to.
  
  
• This website is a great resource for their information boards, tutorials, help, etc: http://www.badcaps.net/
  
  
• This is the soldering station I ordered from Amazon for $23 Soldering Station
  
  
• This is the company from Amazon that I've ordered all my caps from. It came recommended. They show good videos and pictures. Just search by your make and model. They are not limited to just LCD tvs. LCD Alternatives
  
  
  I hope this helps!

Here are some rules to keep in mind:

• Keep your soldering iron clean and tinned, a dirty/oxidized soldering iron doesn't transfer heat well. I use a wet sponge at a bench. If I'm in the field, the hem of my jeans works well. Just quick wipe and a touch of solder for a good shiny tip. (Adding a little bit of solder to "tin" the tip of the iron also aids in heat transfer and keeps dirt/oxidation off.)
  
  
• Be sure your parts are clean too. You want clean, shiny copper to solder to. Wire or circuit boards that have been exposed to moisture are a disaster to solder to. Fine sandpaper and alcohol can clean things up if there's tarnish.
  
  
• Heat the part you're soldering with the iron. Use the hot part to melt the solder. Just like you don't plop your bacon and eggs on the stove, you put a pan down first and put your food in the pan. You're not using the soldering iron directly on the solder...
  
  
• Don't blob your solder on. This isn't paint and it isn't glue. It's liquid metal. Your joint should look almost as if it has been moistened with water.
  
  
• Keep a mental count of 10 sec. Too much heat can destroy components on a circuit board and melt the insulation on wires. 10 sec is a good rule of thumb. If you can't achieve a good joint in that, let things cool down and try again.
  
  
• Too little heat is also bad. It makes the solder joint brittle and the solder doesn't flow evenly. You'll have a grainy appearance. Allow the heat to conduct through both parts you're soldering together. Bigger parts will require a little time to come up to temp. Tiny parts are almost solderable immediately.
  
  
• Remember that solder take a bit of time to cool. Don't move your part around until the melted solder has solidified. Moving it while it's liquid is another way to have a brittle joint.
  
  Start with a pair of wires... Just twisted together wires, like a "Western Union" or "Lineman's" splice.
  
  http://en.wikipedia.org/wiki/Western_Union_splice
  
  It's how I usually install car stereo equipment when putting the car and radio harness together.
  
  Next, you can move up to kits. I wish HeathKit was still selling shit... Velleman seems to sell small trinkets for less than US$10 and you can find them on Amazon. They're fairly easy to assemble, single layer board kits.
  
  http://www.vellemanstore.com/en/minikits
  
  Mainly, it's practice, practice, practice.
  
  You don't even have to spend a whole bunch on an iron... Either of these is quite acceptable and I work on electronics on a daily basis:
  
  http://www.amazon.com/Weller-SP25NUS-Standard-Soldering-Black/dp/B00B3SG70K/
  
  http://www.amazon.com/Weller-SP40NUS-Medium-Soldering-Black/dp/B00B3SG6UQ/
  
  The first one is a 25 watt unit and better suited for smaller circuit board jobs. The second one is a larger 40 watt unit and more suited for wiring type jobs. But both should be acceptable for both types of jobs.
  
  EDIT: Also, as someone who works on electronics almost daily... The was James May should have repaird this was to bend a hook in the end of the wire he was soldering. That way, it'd hang on the terminal strip without the need for a third hand. Iron in one hand, solder in the other.

If you're just dipping your toe in the water, grab that Weller I linked. It's under $40, but is a well respected budget iron. I personally own a Weller WES51. It's a fantastic iron, but if you're not convinced that soldering things is going to become a hobby, save your money.

Hakko is also a popular brand, but I'm not as familiar with their lower-end gear. If you get an adjustable temp iron from Hakko or Weller, you'll be set for a while.

Some other handy items are:

• Desoldering Wick - Just a copper braid that will suck up solder. Great for removing parts from the board.
  
• Solder Sucker - A cheap little vacuum that is supposed to suck the liquid solder off of a joint. I personally prefer the wick with a dab of flux. Others swear by the solder sucker. Both are cheap enough, so grab both and see what you prefer :)
  
• Rosin Flux - a chemical that helps strip corrosion from your contacts, allowing the solder to flow smoothly and create solid joints. There are a lot of versions, but I've preferred using a pen like this one. It can (and will) make a sticky mess, so only use tiny, tiny amounts. (If you use the pen, keep a giant wad of paper towels nearby for when you need to get the flow going. I tried doing it with my hand...it makes a MASSIVE mess. The paper towels help immediately soak up the unexpected flow of rosin.
  
• Helping Hands - Cannot recommend this enough. Typically, you'll see things like this one. But after a while, the joints weaken, and it won't hold anything in place. I bought a SparkFun Third Hand which is amazingly stiff and has held up quite well. Great purchase.
  
  Other things to consider are goggles, a small fan to pull the fumes away from you (DON'T BLOW ON THE JOINTS), and something to solder on top of. If you don't care about your work surface, it's no big deal. But I use my desk, and sometimes the kitchen table, so I have an old 1 foot ceramic tile that I solder on top of -- the soldering iron base doesn't get hot, but you can drip/splatter solder if you're being careless, and it gives you a hard surface to use that you don't have to worry about getting hot/burned.

A good quality soldering iron will ensure that you can get the solder hot enough to make good joints. A soldering iron that does 40 watts is recommended. I started out with a Weller WLC-100, ($40) but am now using an 898D ($70-100) soldering / rework station which uses the Hakko tips (much cheaper than weller tips). The Weller worked pretty well, but the 898D can get hotter and has a digital temperature control. I use a small needle tip, but some people prefer a bit larger tip because you can get better heat transfer.

Use 60/40 rosin core solder, which works great for electronics and RC, and flows very well. You may also want to get some solder paste (flux) which will also help flow the solder and go where you want it to. Usually a solder diameter around .03 inch is good. I use this solder from Radioshack.

If you plan on doing more hobby work that involves soldering, I would highly recommend getting a better iron, prefererably one with a variable temperature range. There are plenty of good options from Hako and Wells that don't break the bank and are much easier to use than the cheap irons.

I have this station

Weller WES51 Analog Soldering Station https://www.amazon.com/dp/B000BRC2XU/ref=cm_sw_r_cp_apa_i_oeAYCbQNC90JB

And this pack of tips
https://www.amazon.com/dp/B01ARYBXLI/ref=cm_sw_r_cp_apa_i_SfAYCbG6XDDXE


Voultar (a great modder to follow, check out his soldering videos for inspiration) posted a good video on a decent iron station he found

https://youtu.be/cGdHJ3BTh_c

Good solder goes a long way to helping make soldering a lot better.

And yes, the clip on loupe is amazing! It magnifies tiny smd stuff really well. I can't recommend it enough.

By far the most important part is your iron. There's lots of good choices out there, but if you can swing it I highly recommend this one made by Weller. It's expensive, but is the best iron I have ever used. It has interchangeable tips including some super fine ones that are great for SMDs, 3 selectable temperature settings you can program, digital variable temperature with a real time temp display, it heats up in seconds, has an auto shutoff if you leave it on and in the stand for too long, and has a grounded tip to help prevent issues with static discharge. You can do it with a cheaper iron for sure, but this one is my first choice.

No one taught me how to solder, I just kinda did it. Buy a soldering iron (like I said get one in the $50 range, obviously if you have money to burn a $100-$200 one is going to be 'better'. I use a WLC100 http://www.amazon.ca/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC ) some solder, and start connecting components together. I would also pick up a desoldering tool, I use one of those bulbs but there are better/different types out there.

You can use use a breadboard with wires. That's sorta the recommended way to experiment. I tend to move things to protoboard pretty quickly as I find things get messy quickly and it's easy to disconnect things.

I should say I'm not an expert - I'm actually more of a beginner in the world of electronics, but I thought I would share my experiences of how I got started because the path is not totally clear.

I really wish someone told me that ebay/china was the place to go for components. It's stupid but it's just so much cheaper. (I got burned with sparkfun when I was building a project, $100 of parts, $50 shipping - I wanted it fast and it wasn't that much more - then the kicker $50 in import fees/duty at my door) After that I learned mouser was good, $200 and you get free shipping and duty - ended up ordering lots of random things and lots of things in bulk - need one resistor? Might as well get 1000 :). I recently learned digikey is in canada and does fairly cheap shipping so I tend to order from there now if I NEED something fast.

Ebay is the best though for stuff if you're in no rush though, and totally the best place to get stuff like protoboard, breadboard, jumper wires, resistor packs (assorted resistors) LED's, assorted IC's, etc.

For a soldering station I would consider new unless you find a great deal on something... For example, I use this at work, it's never given me a problem and it's used quite often (we're a semi conductor manufacturer and I share the lab with another)--granted we use a set of Wellers for most of the soldering, but the Aoyue gets high use for the heat gun and occasionally the soldering iron. I liked it so much that I bought one for home, yeah it's a bit high, but if you're doing SMD or other soldering stuff you will appreciate some of the features and included items.


I'm not sure about power supplies, but one good thing there is that age is usually not a big issue, and if you're just needing standard supplies you can probably get away with a decent 12V supply and then build a few regulators for lower voltages.


I've heard that Rigol oscilloscopes are a great value, and that that the lower rate units can be firmware hacked to higher rates. Personally the trouble I have is that after using $5000 Tektronics scopes at work I can hardly even stand to step down to a $2000 Tektronics, so I can't imagine what using a $350 Rigol would feel like... but if you have nothing, this isn't bad.



I'd also check out ham radio flea markets. BTW I have to say that if you are into electronics and what to make a life/career there is no better place to be than into amateur radio. the ARRL handbook alone is an amazing reference. As a personal responsible for documentation at my work I'm blown away by the quality of the writing for those handbooks. Even older copies are great and they're usually cheap. I have a 2003 copy at work and reference it regularly for either the information I need or a great starting place for researching a topic.

I hate to say it, but RadShack makes my favorite budget desktop soldering iron. I have one of these and it works wonderfully. I've been through about 40 tips over the last 3 years with it, not counting one-use modified tips.

At the school lab, we were using this (in quantity at lab desk) or this (instructor's, who would loan it if we knew how to solder). I am going to miss the school lab. Transferring to the next higher level at a different university, where a friend attends, and their lab sucks.

If I bought a new one, I'd get the Weller WD1002. Until I upgrade to that, I'll keep my radshack 64-053.

If you buy a $13 soldering iron, you're buying a $13 soldering iron. Some will work better, some will work worse. Really doesn't matter where you bought it. I never had one last more than a few months.

If yours started out working ok then didn't, make sure your tip is clean. A highly oxidised tip left on overnight isn't going to work well, no matter the iron... if your tip is black, replace it. If it only came with a fine point tip, consider a different shape tip. Fine point tips (generally) only work well with higher power soldering irons.

If you want contactless-soldering, then you're not looking for an iron. You're looking for either a hot air reflow station or an iRDA station. Irons are meant to touch the solder to melt it. Hot air works with solder paste, meant for very low temp soldering (SMD safe). iRDA uses infrared light to melt solder, generally used for specialized surface soldering.
***
It sounds like you may be a little new to soldering, so I also highly recommend this comic to you... Soldering is Easy - PDF. I highly recommend it to those who have been around the block a few times as well.

Eh, soldering just takes a bit of practice, and there are tons of Youtube videos that explain in detail the best ways to do so.

(I'd recommend this channel https://www.youtube.com/channel/UChbLnX8JcsN9bH4BNgJZ6wA)

Really it's all about not holding the iron on the board too long. Once you get that down, it's easy. Learning the wire gauges and all that is also very easy as most boards have recommendations in the paperwork. (if it carries power, big wire... If it carries signal, smaller wire). These new DNA boards are about the easiest thing ever to work with, and even someone with little to no experience could solder them with ease. (now the DNA20/30/40, notsomuch)

If you're looking for a good soldering iron, you want something with wattage control, and while weller has been the standard for decades, they are overpriced and a bit hardcore unless you are a pro. I'd highly recommend the Hakko FX888D http://amzn.com/B00ANZRT4M which is what pretty much everyone uses, or what I personally use, the Aoyue 9378 http://amzn.com/B00BSW69LI which has served me very well. There are others for considerably less, and if you aren't planning on making this a hobby, then something like the Aoyue 469 http://amzn.com/B00MCVCHJM would be perfectly fine. (60w is about a low as you'll want for a variable wattage iron, so you'll have a little wiggle room)

Look up some tutorials on youtube. A good iron makes a world of difference. I struggled with properly tinning all the irons I've used previously which were just those cheap $8 dollar irons from like walmart. The weller that was in my dad's stuff wasn't much more expensive but they make quality stuff.

The tip tinned very well and everything was fairly smooth. If you don't have a decent stock of soldering supplies I would purchase them before you start.

Here's a quick rundown of what I would recommend:

Simple Weller Soldering Iron

Helping Hands

Desolder Wick

Kester .03" solder

Having the desolder wick saved me a few times when I had some bad flow from the parts not having adequate heat and the solder just clumping on the pin rather than flowing into the connection. You just lay the braid over the solder and press your iron on top and it will soak the solder into the braid and leave your parts clean. You'll probably want something to clean your solder iron tip with. You can buy a Hakko cleaning stand with wire brush for $10 on amazon or you can just wet a scotch brite pad you buy from walmart for a few dollars.

You can use solder you already have if it's a small enough diameter. You want small diameter so that when you touch it to the part (not to the iron) it melts quickly and you dont have to continue to apply heat to the parts. As far as actually handling the solder while you're trying to work I like to cut a small length of solder, maybe 6-8 inches and then wind it in a mini spool around my pinkie finger and leave a length of it sticking out so you have something to hold on to that will give you good control.

How-To Solder Instructable

Once you make the connections look at them, a good connection should typically be shiny and not cloudy. It's likely overkill for this project but those are good practices.

You'd be surprised a) how easy it is to use Arduino, and b) how helpful the online community is. The nice thing about Arduino is that the complexity remains the same, regardless of how many sensors you add, provided you have enough expansion breakout board.

For a first step, I would buy a starter kit and a cheap soldering iron and a half-decent multimeter and just start making little projects, like light sensors and temperature sensors and making those projects both wireless and online.

After that, it's just a matter of interfacing the larger, higher-voltage components (like pumps and valves) with the lower-voltage Arduino. This is easily accomplished with a relay, which is also useful for electrical isolation between the two subsystems.

Start small. I would recommend making an Arduino into a timer, and then using the timer to control a pump. Then add an online API that allows you to adjust the on/off time of the pump. Then add water level sensors, then temperature sensors, etc.

Also, make sure you prototype everything on a small scale first, like the guy in the video was doing on his desk. It will save you a lot of money if you mess anything up.

Once you develop the skills necessary to build your smart-system, I cannot stress how important a good, detailed electrical diagram is. It doesn't matter if it's professional-quality, or done with pencil and a ruler. It will save you so much time.

>That's it - just two solder connections?

Yep. If you buy from Mountain Electronics and select the option for wires on the driver, then you just need to thread the wires through the pill and solder them onto the LED board (you might need to shorten them first). /u/potatoworld made a video that should be helpful: https://www.youtube.com/watch?v=1ngJaTn_rjE. There will be some differences with the Convoy.

> What would you recommend, for a high quality soldering iron, and what type of solder works best for flashlight work?

Lots of option out there for an iron. I've seen good reviews of this one for a budget option. For a solid station you'll use for a decade or two, this Hakko is probably the most popular. Make sure to pick up a few extra tips.

For solder, make sure it's 63/37 eutectic. This means it goes directly from liquid to solid without the pasty time in-between, which makes it flow better and leads to less "cold" joints. I like Kester 44 0.031in (you can find it elsewhere cheaper, just make sure it's the right one, they have lots of different blends and thicknesses).

This is really all I needed to be happy and dangerous. I was actually just doing more research when I saw your reply come though. I just didn't know if it was even possible to wire these connections. My basic understanding is that it should be possible but there's so much I don't know.

​

As for my soldering skills, they are probably "Beginners moderate" which is a thing I just made up. I've got the right gear to do the work but, as I'm sure you know, having the right gear is 10% of the job. Burned through 2 Teensy ++ 2.0's before I got it right with my last project.

​

And I'm totally comfortable ruining some more hardware to try this. I'm actually excited by the prospect. I think I kept those teensy's. If I can find them, I'll practice by trying to remove the smt micro usb ports on those. Not nearly as hard but a better start.

​

Anyway, really appreciated the reply. If you have the time to confirm I'm trying this with the right hardware, that would be just gravy. You've already done more than enough, though.

​

I'm planning on using my:

- Hakko FX888D-23BY Digital Soldering Station

- T18-BR02 Tip

- and the thinnest solder I could find that still has a rosin core

​

Anything look like the wrong choice? Tip and rosin?

​

Thanks again for all the help

Good quality as in: Will work for Nerf stuff for a while, or solid build quality where you won't have to replace it often?

If you want to go for something that's no-worries and will probably last for the foreseeable future, the Hakko FX888 is SOLID.

Anything else I'd consider "nice" would have to have a soldering iron holder and temperature control that I trust. Very nice features, because if you leave the iron sitting for a while and don't tin the tip, the heat will start to oxidize/damage the finish of the tip and become unusable. This can also happen on any iron if you leave it running hot for a while, but something that's temperature-controlled rather than with an arbitrary power knob will keep your iron tip intact much longer.

Mid-tier would be something with variable power control but not temp control. You might be able to get away with lowering the power while you work instead of turning it off.

The "Amazon Special" that UNW1 linked is a fantastic soldering iron for the price, plenty of power whereas other cheap irons won't heat up quickly enough. I'd recommend it for most people starting out, since it's great for learning the basics + soldering iron care. There is practically no temperature control on the thing though. I turned it way down to minimum (Claimed 200-250C, which is nowhere near hot enough to melt solder) and it still threatened to overheat.

I've heard of irons that are even better than the Hakko/similar models in terms of where the heating element's located, other features... but I don't have much expertise in the field and haven't seen a need for those. As far as I'm concerned, $100 is as high as you need to go for now, and $50 can probably get you set up with a solid iron.

Do you have a soldering iron at hand already? I wouldn't recommend this as your first soldering ever, they're pretty small connections and if you heat up the wrong part for too long you can damage them permanently. It takes a good amount of looking through the forums and researching but it can be done. I didn't have much soldering experience beforehand but I modded a different pair first to really figure out the wiring situation. I bought this soldering iron to do it and it works really well and I've been using it since for a bunch of other things. Just look up some tutorials on learning to solder before buying it to see if you think you can do it.

I wouldn't recommend that cable I have pictured, it's pretty hard to carry around and it makes a ton of noise when you tap it. I started making my own cables, which is a whole other process, but also a great way to learn soldering without the chance of fucking anything up.

I modded the hole slightly differently than how I saw other people doing it. Most people use a dremel to widen the hole a bit to get the jack to fit, but I didn't have one, so I ended up melting the edges a bit with my soldering iron. Would not recommend, it was super messy and probably dangerous.

You can ask me anything you need to here and I'll help you out, the process was tough without anyone to walk me through it so I know how it feels, but it's amazing when it's done. Very accomplished feeling.

You may have heard the old saying:

>The road to success is through experience.
>
>The road to experience is through failure.

It sounds like you have already achieved some failure, so this means you are well on your way on the road to success!

Let me add another old saying that I just made up:

>Good technique may overcome a bad soldering iron.
>
>A great soldering iron will never overcome bad technique.

You didn't mention what kind of iron and what kind of solder you are using now. But if you are getting cold joints, that is more likely a sign of bad technique rather than the wrong iron.

Cold joints happen when you heat the solder instead of heating the work material. The hot solder hits the cold metal and freezes in place instead of flowing onto the hot metal.

You need to heat the work material itself first. If it's a through-hole component, then after you turn the board upside down, touch the iron to both the component's wire lead and the board's pad. Only after both of those heat up do you apply the rosin core solder to melt onto and into them. Then you will have a beautiful shiny solder joint.

This does take some finesse and attention to timing. So I would do this Heathkit style. The Heathkits I bought when I was a teenager always came with clear instructions on how to solder, and most importantly, some extra pieces to practice with. I learned to get the technique down on those before tackling the kit itself. So practice on scrap material until you have it down.

Of course a good iron and good solder will help. If you're using lead-free solder, I might suggest a traditional lead-tin solder instead, as it is easier to work with.

For an iron, you didn't mention what you're using now, or what your budget might be. If something around $100 works for you, you can't go wrong with the Hakko FX888D. You might want some extra tips of various sizes too.

Desoldering is an art to itself. Do you have some desoldering braid? I used to use the "soldapullit" suction pumps and similar things, but the braid always gave me better results. It comes in different widths so you can pick one that fits the work you're doing.

I hope these notes are helpful. Holler back with any questions, and happy soldering!

You look like you are using a proper soldering iron. But I don't know for sure.

Nicer irons used for electronics have proper temperature sensors and can dump a lot of energy into the tip to maintain the desired temperature as much as possible.

Something like this: https://www.amazon.com/Hakko-FX888D-23BY-Digital-Soldering-Station/dp/B00ANZRT4M

Cheaper soldering irons you can typically pick up in a hardware store depend more on a sort of 'slow equalization' were the amount of energy used is a pretty much constant. The 'temperature control' really is just mostly a resistor that limits the energy going into the tip.

The big 300w irons work a lot better because they have large thermal mass. They can maintain their temperature better then the cheap hardware store ones because of this.

The problem with using a cheap iron is that it takes much longer to get the surface of whatever you are soldering too up to the proper temperature. This gives a lot of time for the heat to soak into whatever you are soldering and by the time you get the lead hot enough you have dumped a massive amount of heat into your work piece.

If you have a nice iron then it maintains it's temperature better and gets the surface hotter faster. This means that it takes a lot less time to get the surface to the proper temperature and less heat is needed overall.

You probably would of had a easier time getting proper looking 'tinning' of the battery with more surface prep. Solder works through capillary action as it 'follows the heat'. The solder wants to get 'sucked' into joints that are hot. So using rough sand paper (80 grit) to scrape up the surface probably would of helped. I would of sanded the bottom and then used acetone or alchohol to clean everything.

Another thing that would of likely helped is brushing on soldering paste onto the surface. The resin/paste is a acid that helps prep the surface when it heats up. The solder isn't going to want to join to surfaces with oxidation, oils, or other things. The resin cleans the surface to help. The resin core is there to do that as well, but it's usually useful to brush more onto the work piece.

Also you don't want to hold it for a pre-determined amount of time. You can tell if you are doing good job by the surface tension on the blob of solder and seeing it flow.... which you were having a difficult time doing on the bottom... which is perfectly understandable and expected.

All in all I think the video is a good demonstration of the problems with using solder. I think you gave a fair shake.

Hey! :) I also use a hi-powered magnifying glass (a cheap $5 camera +10 macro filter) mounted onto a Flexible Helping Hand). Detail painting becomes infinitely easier when you can see what you're doing. Lots of light also makes all the difference.

in addition to the excellent information /u/bmatys has provided, for fine painting, I use oil paints on acrylic or lacquer gloss coats. This way one is able to use a combination of paint application and removal (with turpentine) to get really fine strokes. Make sure the turpentine/thinner doesn't attack the paint coat you already have on. Obviously you're using the thinnest brush you have at hand.

Also it's a good idea to support the palm of your hand to steady your strokes.

-a good workbench with clamps and a lot of surface area

-a soldering STATION. I have this. also buy LEAD solder, and those little things of cleaner/tinner are super useful.

-fume extractor (optional, but very easy to build with a fan and some ducting. Worth it.)

-pliers, wire cutters, crimpers, and strippers,

-lots of extra wire

-heat shrink tubing and something to heat it with.

-lots of extra screws/zip ties/fasteners

-somewhere to put screws. A flat tray works nicely, but magnetic ones are the best.

-a multimeter or oscilloscope. I use this.

-prop balancer. Very necessary, especially if doing video or using cheap props. (They can explode if not balanced.)

-lots of lamps and light sources.

-a pair of Helping Hands for soldering.

-hex wrenches/screwdrivers

-good hacksaw/hobby saw/Xacto knife.

-calipers/rulers

-drill/dremel

Yep, I've been building stuff for a while, although this is the most intense set of builds I've done. Get yourself a good soldering iron and a couple of spare tips (Weller makes some good ones-- don't go for super-cheap unless you want to replace it a bunch of times). This thing here is about the lowest-end I'd suggest (I use one): https://www.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC

Get some little noise toys, like an Atari Punk Console or even something silly like an LED Christmas tree kit and put it together. There are some really good soldering instructions here:

https://learn.adafruit.com/adafruit-guide-excellent-soldering/tools

They list more info on tools, too.

Some kits are more complex than others, too-- the Befaco kits are pretty complicated, and anything with an oscillator will probably require some calibration. Synthrotek make pretty good little kits and have good info on building them.

You can do it, though. It's not difficult. 8) Just take your time and check each step as you go and you'll be fine.

I am out of town, but can try to help..

Cheap soldering kits make it hard to get a good, consistent temperature on the tip, and the recovery time (time for the tip to get hot again after bringing it down by cleaning, etc) is poor. You'd want to get an adjustable one if possible. You could easily be working too hot and causing yourself problems. Lead free solder is harder to work with. I have a Hakko that I love, but something in this range would be a worthwhile investment and a fine iron.

As for the soldering, you really are just jamming the iron into the two pieces of metal you are trying to join, and then slowly feeding the solder into the junction. Use as little as you need to get a tiny, clean joint, and never a 'bubble'.

Removing solder is a horse of a different color. That is a pain in the ass. For that, you will want a lot of flux and a hot-hot iron (as hot as you can go before you start damaging things/burning down the house like you say). It's not fun to remove these components. Sometimes you get lazy and snip out the old one and try to work out the lead with a needle-nose and the iron (fluxed up hole) at the same time. Helping hands or a good vise can be crucial for this.

I'm no great master at it, but it's really one of those things you can pick up watching a few youtube videos or hearing instructions (with the right equipment) and pick up. I taught a friend the other day for a project they are working on. It really is just practice to get good, and that seems to happen quickly once you get a feel for working the solder.

Soldering is actually not that big a deal. A little practice and you’re good to go. THeres lots of YouTube tutorials. and you can find wiring diagrams all over the Internet.

Get an iron with variable setting like this one it’s a bit more than the $15 for just a plain iron, but it’s worth it and you can use it forever.
Looks like you’re painting it. You can try all sorts of different techniques; I’d maybe go solid color the first time. guitar reranch sells rattle cans of nitrocellulose based paints and clear coats (that’s what expensive guitars use as opposed to poly)
He uses chips from old guitars and cars(fender used leftover paint from car companies for many of the original classic colors) to match proper color and hue, and they come with two different spray nozzles. Again, a little pricier than cans from the hardware store, but nitro finishes are so nice:)
One of the best parts is researching everything! Lots of time on the google machine:)
Enjoy

Step 1: Buy a multimeter. I prefer the Fluke 87v http://amzn.com/B0002YFD1K Sure it's $387, but it'll pay for itself eventually.

Step 2: You'll need to take apart the charger. A good set of screwdrivers would definitely help. http://amzn.com/B000NZ5QG0 It's only $40. Wiha maybe isn't the best, but I like them and they do offer a 100% satisfaction guarantee.

Step 3: Once you open it up, you can start testing it with the multimeter. Inevitably, however, you'll probably have to solder something. Hakko is a popular brand for good reason. This one is under $100 AND it comes with wire cutters: http://amzn.com/B00AWUFVY8

Step 4: After you put it back together and find out that it's still not working, buy a replacement charger.

If you are a total noob, I suggest you just get any 60 W soldering iron. Really. This one suits you and cost less than $10. Because getting a FX-888D now is like killing mosquitoes with cannons.

You also may need a stand where to rest the iron when not using it. It comes with a sponge so you can clean the iron tip from time to time (just don't forget to wet it before use).

Finally, you will need some solder. Stay away from lead-free solder, this stuff isn't for amateurs. Get a good-old 63/37 solder with rosin flux core, this one have a 0.3 mm diameter, small enough to even solder SMD components (but don't start with them, they need more practice to be hand-soldered).

Soldering isn't a difficult skill but it requires practice. So you better start small and take easy steps. In no time you will be soldering SMD components. :)

PS: you also want to get some desoldering wick and a hand vacuum pump/solder sucker, those are more useful than you might think.

DISCLAIMER: all these items are just suggestions, buy whatever you think is more useful for you. Just wanted to give you a start point.

You certainly can use that soldering gun but it won't be fun or easy because it is so large (that's what I started with and used for a few years). I'd suggest picking up a Hakko FX-888D or Hakko FX-951 if you have a desire to continue with electronics.

Definitely add more solder because it has flux in it which will clean the oxides and allow the solder to flow out. You will also need to use a bit of solder wick/desoldering braid to clean up the pad before fixing it. You'll want to get some Kester leaded solder to work with.

Watch these Pace soldering tutorials before you begin to understand the basics. Heat the pad and wire then touch the solder wire to the joint. If you add it to the tip of the gun/iron the flux will burn away and it will start to oxidize. Doing it that way certainly has it's place but it isn't for this type of work as you'll need to add extra flux to protect the joint.

Like several others have mentioned, /r/diypedals is a good place to go. As long as we've got you here, though... I had already practiced soldering before and wanted to start with a kit. That way you have everything you need and just have to assemble. A very easy and inexpensive first build was [this] (http://www.generalguitargadgets.com/effects-projects/boosters/stratoblaster-booster/) boost pedal. Don't let the simplicity fool you. I still have this boost pedal on my board to this day and love it. Also, I picked up [this] (https://www.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC/ref=sr_1_2?ie=UTF8&qid=1483458417&sr=8-2&keywords=weller+soldering+station) Weller soldering station. Crazy cheap, but I've been using it for over 6 years with no issues. Finally, just read, read, read and read some more! There's tons of great info in various forums, books and youtube videos to get you on your way. Best of luck and have fun with it!

My most used meter is this cheap $15 GE box. I have some nice ones, and if you're only going to have one get one that does >500V, but this one is compact and reads well enough that I tend to use it the most. I have a couple nice meters which also do caps, diodes, transistors, auto ranging, up to 1000V reads, etc. They're very handy.

Get some bias probes. The kind that plug into your meter are good and inexpensive, if you want to go spendy the eurotubes box that reads out plate voltage and current directly is a nice piece of gear. Get a soldering iron with adjustable range and replaceable tips. I had one of the cheaper weller irons, it eventually shorted the pot so it's on full all the time (something I could fix but haven't) so I used that as an excuse to get a nicer iron. If you plan to do any solid state something ESD safe if a good idea.

There are a lot of factors that come into play on how much it will cost. Even with DIY you have options. You can do real DIY, where you have to find schematics, source the parts, make your own pcbs, make your own front panels...or you can buy kits. I cant read schematics so I went the kits route.

It still cost me some money to buy equipment: soldering iron, solder, circuit board holder, tweezers, wire cutter, headband magnifier.

From there I mostly stuck with products from AI Synthesis, Trogotronic, and Befaco. Those companies all sell kits with very clear instructions. I was new to soldering so this was key for me. Some other kits I bought had very poorly written instructions and their support was just as well done as their manuals.

If you know what you are doing then you may have better luck. You can also try modules that require SMD soldering. Mutable Instruments has released all their code. Amazing Synth is a great resource for high quality pcb's. They dont sell the parts though so you gotta find the BOM and source the parts. Amazing Synth has the BOM's for most, if not all, of the modules. You'll also need to do some programming and upload the code from a computer to the modules.

To try to answer "how much will it cost" it really depends on how many modules you plan on making and what method you choose.

There's a whole subreddit dedicated to those of us who DIY...come check out /r/synthdiy

I have this iron. I think I paid $30 like 3 years ago, but it's totally worth $60 if you can't find it on sale. It's survived about 7 builds and 4 desolders, + soldering like 50 mini PCB things from work. Adjustable temp makes things easier as well, so you're not burning everything.

I use 0.031" Kester. It's thin, melts at a fairly low temp, and doesn't make a huge mess. You can use other solders for sure, this is just what I've found to be the best (whatever you can find at ACE, Home Depot, Lowes, or whatever that's somewhat thin should be fine).

So here's all the parts you need.

Maxipad - http://www.switchtop.com/product/gamepad-macropad-pcbs

Diodes - http://www.mouser.com/ProductDetail/Fairchild-Semiconductor/1N4148/ (I'd just buy a roll of 100, they're $0.019 each at that point)

Switches - http://www.switchtop.com/product/gateron-switches

Teensy (your controller) - http://www.mouser.com/search/ProductDetail.aspx?R=0virtualkey0virtualkey199

Plates you'll have to find somewhere, but there are some on here that can make them for you. I have the DXF I used here that you can share with someone who can make the plates for you, it'll end up coming out looking like this if you use those (material and color are your choice, those are clear acrylic).

You'll also I guess need an iron, but that can be seen as an investment into multiple boards, rather than just this one. Best bang for your buck is going to be this one.

Soldering through-hole diodes is easy, and the Teensy comes with header pins that you use to solder it.

Important note: Solder the switches and diodes before the Teensy, as you can see that the area covers some of the switch headers. :)

I can help you along the way with any issues, so let me know if you need any help.

I have a very similar vise in my workshop. Works great and I love it, but third-hands are amazing if you get a good one. I tried this one out after seeing the amazing reviews on Amazon and was not let down. Having 4 clamps instead of 2, and having them be able to lock down makes a world of difference.
https://www.amazon.com/QuadHands-Helping-Hands-Third-Soldering/dp/B00GIKVP5K

I also have one like this, only not quite as expensive:

https://www.amazon.com/Tools-004-570-Regular-Soldering-Station/dp/B01579QJYO/ref=sr_1_95?s=hi&ie=UTF8&qid=1518811625&sr=1-95&keywords=third+hand

I don't know about making repro crats, but I do know about mods and repairs. I have done an overclock mod and 2 s-video mods on my genesis consoles, as well as lots of repairs on other consoles.

I have the basic tools like screw drivers, needle-nose pliers, and some tiny cutters just like these.

My soldering iron is a cheap 35 watt fixed temperature hunk of crap. Get a better one. I don't have any recommendations, but this one is linked to from this subreddit's sidebar. It has good reviews, but I haven't tried it myself.

I also have a spool of thin rosin core solder that is about 1mm thick. I also have a spool of de-solder wick which comes in handy.

To hold down and/or secure wires I use some rubbery electrical tape or hot glue. I use the electrical tape whenever I can, since it is easier to remove than the hot glue. The hot glue is useful in small amounts to keep wires from getting accidentally pulled out of place.

A multimeter is very useful. You probably won't need a really fancy one, just a basic $10 one.

I bought one of those parallel cables that all the old printer's used for only $1.99 at a thrift store. It's packed with different colored wires, that are just the right thickness to use for most console repairs/mods.

How good?

Here is one that will last you pretty much for whatever no matter what you do with it, its the soldering iron I have used for the past several years and has been great on a number of projects: https://www.amazon.com/Hakko-FX888D-23BY-Digital-Soldering-Station/dp/B00ANZRT4M/

Here is one that will do just fine but isn't great or anything:
https://www.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC

The most important feature for a good soldering station is variable temperature.

The only other things you will need is solder:
https://www.amazon.com/WYCTIN-Solder-Electrical-Soldering-0-11lbs/dp/B071G1J3W6, a solder wick: https://www.amazon.com/MIYAKO-Desoldering-Wire-Handy-Dispenser/dp/B010VMHR5M, and possibly wire cutters if you don't have them: https://www.amazon.com/Hakko-CHP-170-Micro-Cutter/dp/B00FZPDG1K

Some personal advice is get the best one you can afford if you thing you will use it a lot, the difference between a okay one and a great one is huge. I hated soldering till I got a good iron.

  <br />

Had some free time so I wrote this:

If anyone wants to do Soldering,

• I highly suggest watching a few Youtube videos on techniques on how to hold it the right way.
  
  
• Buy a GOOD IRON (Weller or Hakko) NOT a cheap one!
  
  
• Buy a station to rest the Iron on if it does not already come with it (A sponge is recommended)
  
  
• Safety glasses and roll your sleeves up, just in case!
  
  
• Buy a smoke absorber with a carbon filter, OR! build your own with a old phone charger as a power source, a switch, a cheap car filter and a old computer case fan... your making electronic gizmos anyways... WHY?: Because breathing Tin and Lead is fucking cancerous, and blowing it away without a filter is how you get pets, kids, or bacon to inhale cancer too.
  
  
• Have a clear space to work with no combustible materials, avoid burning down your place.
  
  
• ESD grounding wristband, I know it's lame. But It will save you a static shock, which could potentially result in a dead component on a board.. Also you should have one of these if you build your own PC. A $2.00 part can save you HUNDREDS
  
  
• Remember to use the right size tip for the job, and to clean your Iron's tip after using it to prolong it's life.
  
  
• If you cant afford these basics, either don't go out this weekend, and save up for them. Or find someone who does have these things that you can borrow.
  
   
  
  Soldering is extremely fun, rewarding, can motivate you about electronics, save you money, and convinces your friends to think you are some kind of "fire stick-wand wielding wizard of electronic black magic" (+7 to charisma!).
  
  But remember to solder safely!

I'd say so. It would take a bit of reading and practice, but you could do the version look mum has in his tutorial pretty easily with larger components..

The biggest challenge/cost sink I would say will be getting a decent soldering iron and learning to use it.. But with the stripboard he's using, it should be pretty painless.

Good Soldering iron
https://www.amazon.com/Hakko-FX888D-23BY-Digital-Soldering-Station/dp/B00ANZRT4M/ref=sr_1_28?s=hi&ie=UTF8&qid=1541069778&sr=1-28&keywords=weller+soldering+iron

cheap (but good starter) iron
https://www.amazon.com/Aoyue-Programmable-Station-ESD-Switchable-Configurable/dp/B000I30QBW/ref=sr_1_7?s=hi&ie=UTF8&qid=1541069874&sr=1-7&keywords=aoyue+soldering+iron&dpID=41lx2CM8bML&preST=_SY300_QL70_&dpSrc=srch

Lead-free Solder
https://www.amazon.com/Lead-Free-Solder-Wire-0-5-2mm/dp/B071GKC3L5/ref=sr_1_2?s=hi&ie=UTF8&qid=1541069977&sr=1-2&keywords=solder%2B2mm&th=1

stripboard
https://www.ebay.com/itm/Strip-Board-Stripboard-PCB-Choice-of-110x93mm-or-94x53mm/222345513198?epid=1055105041&hash=item33c4d348ee:m:m-UAITK6Q2h19Ao6VjMWGoQ:rk:28:pf:0

I may end up putting together some kits if I can figure out how to streamline some of this while keeping it affordable..

A calculator: TI36X Pro, Casio fx-115ES PLUS, or HP 35s (these are the 3 best calculators allowed on the FE and PE)

If you get a graphing calculator, either get the TI-84 Plus C (which can be used any time graphing calculators are allowed), or get an HP Prime or TI Nspire CS CAS (which are WAY more powerful and useful).

Pencils: Pentel Graphgear 1000, Pentel Kerry, or Rotring Rapid Pro (include an eraser such as the Sakura Foam Eraser). The rapid pro pen is also pretty popular. 0.5mm led is more popular than 0.7mm.

Engineering paper.... especially with some pressboard report covers. They make nice notebooks (albeit expensive), and pair really really well with looseleaf textbooks.

A whiteboard and markers.

a copy of K&R2.

Pricey: a nice soldering station, a multimeter, or a used oscilloscope (such as a Rigol DS1052e).

^^^\The ^^^HP ^^^is ^^^more ^^^expensive ^^^because ^^^it's ^^^targeted ^^^at ^^^professionals, ^^^rather ^^^than ^^^students.

Don't cheap out on an iron. It's one thing if you absolutely can't afford something from hakko or weller, but if you're going to be doing any amount of soldering a better iron is going to be worth the money, even if you've got to save up a bit.

For someone who anticipates doing a decent amount of electronics, I'd generally recommend the Hakko FX888.

Advantages:

• Heats up in moments (not 10 minutes). This is good because it means the iron recovers more quickly.
  
• Build quality. I've been using an old Hakko 928 that I received second-hand since like, 2006-7 and haven't even needed to replace a tip

It really depends on whether you want a nice soldering iron or just something that will allow you to try it for a few hours. There is a huge price difference. Of course there is also a huge difference in quality. You could get a very nice iron like this for around $250. Or you could get something much less expensive, like this for around $40.

The first one I listed is very similar to one of the best irons I've ever used. The second one is still head and shoulders above the piece of crap I used for the first several years I was soldering. It was like this, at around $5, and as long as I kept the tip sharpened with a file it worked pretty well.

It depends what you are working on, but if you are working on through-hole and SMT in the under $40 price range I'd go with a Weller WLC100. It was my first iron and I used it for a long time before I finally upgraded (I still use it sometimes).

The stock tip was a little big for my taste so I bought a replacement (ST7) tip. The ST7 is a smaller conical tip. You can also find these on Amazon, but pay attention to the shipping if you order it off Amazon Marketplace, some 3rd party tool vendors will gouge you!

For the Fume extraction you should buy a fume extractor... heh. Pretty simple. I built my first fume extractor from an old PC power supply, an old exhaust fan, an articulating lamp base, some activated charcoal pads, and a length of dryer hose.

You can certainly go that route and build your own. It's nice if you already have the parts on hand, but eventually it became too unwieldy so I bought a Weller Fume Extractor. You can buy something similar for about half the price on Marlin P. Jones, but I was never able to catch them in stock.

Either way, look around, have fun, and good luck!

• Save yourself a few bucks and get the Hakko / Snip Combo.
  
• I beat the shit out of my 10 yr old radio shack fire starter, and now i LOVE my Hakko. To be prepared I found this video on how to take care of tips. I've been doing this guys method from the start and HOLY BALLS my tip is still in good condition after several months of use. I even bought extra tips from HK thinking i was going to need them. LOL.. maybe down the road or precision soldering.
  
• I know you said you have hex drivers, but i picked up this set due to my original hex set stripping. The Titanium apparently keeps from stripping.. have yet to strip them, so we'll see. Also good to have something at the bench, and an on the go set for the field. I actually have a multi-tool from HK for the field.. it's not titanium but it works.
  
• I also have a multi-tool ratcheting hex nut driver for my props.
  
• zip ties
  
• blue lock tight for motors
  
• personally i have yet to use or need a heat gun, if it's for shrinking heat shrink i simply use a lighter.
  
• little baggies for small parts. I label mine where these parts came from but not necessary.. e.g. Cobra motors, Naze32, Strix frame, etc.
  
• i picked up a cheap helping hands from Harbor Freight for like $3.. it comes in handy.
  
• Lipo Checker.. i personally got a Hyperion EOS Sentry 3 for $11.
  
• XT60 male/female connectors
  
• 12/14/18/20/22/26 AWG wire..
  
• Car bulb for smoke stopper.. this should be the FIRST thing you build.. it's saved me sooooo many times.
  
• electrical tape.. lots and lots of electrical tape.
  
• double sided tape.. foamed/padded
  
  probably more.. but all i can think of right now..
  
  
  

I have a Weller WES51 Analog Soldering Station, and I highly recommend it for just about any kind of work. https://www.amazon.com/gp/aw/d/B000BRC2XU/ref=mp_s_a_1_3?ie=UTF8&qid=1518809457&sr=8-3&pi=AC_SX236_SY340_QL65&keywords=weller+wes51&dpPl=1&dpID=41WVs6AdNqL&ref=plSrch

The slightly more expensive digital version doesn’t solder any better, it just has buttons and a display instead of an adjustment knob.

If you’re working on tiny components, then you’ll just need to buy a few smaller tips, but there are plenty of sizes and shapes out there for Weller irons. I’ve always just bought cheaper knockoff tips, like the ones where you can get a variety pack of 10 for ~$30 on amazon. I don’t think tips are really worth spending a premium for the Weller brand, unlike the iron itself. Something like this: https://www.amazon.com/gp/aw/d/B00VFYPKN2/ref=mp_s_a_1_fkmr2_2?ie=UTF8&qid=1518809384&sr=8-2-fkmr2&pi=AC_SX236_SY340_QL65&keywords=weller+replacement+tip+set+wes51

I’d also recommend a good vise or workstation to hold things steady, because there’s nothing worse than trying to use crappy little helping hands or just solder on a bench top. I use a Panavise like this, just as an idea, but there are probably some decent cheaper options out there: https://www.amazon.com/gp/aw/d/B00011QA0M/ref=mp_s_a_1_1?ie=UTF8&qid=1518809613&sr=8-1&pi=AC_SX236_SY340_QL65&keywords=panavise+350&dpPl=1&dpID=41smUr9QAlL&ref=plSrch

I've heard a lot of people in /r/arduino and similar speak highly of moderately-priced soldering stations like this Weller one. While I love my JBC, on price alone I can't entirely recommend it.

What I've always found is best are skinny (and preferably interchangeable) tips with a decently powerful element behind them, giving a good mix of precision and power. You should definitely buy a "station" style soldering iron rather than the cheaper kind where the mains cable goes straight into the iron, the lighter-weight cable between the base and iron makes the whole process so much easier.

My advice for learning would be to start with an everything-included kit that produces some kind of usable item at the end. This was the first Google result for "through hole soldering 101 kit", which appears to be some kind of "Simon" game. Coincidentally, one of the first things I remember making with my own soldering iron. You can move onto surface-mount, assuming you don't get the bug and decide to go straight to reflow soldering once you've figured out which is the hot end of the iron, buying a reasonable iron rather than a bargain-basement one so you get a sufficiently precise tool will enable your first purchase to carry on working for you longer.

My only other piece of advice would be to avoid lead-free solder like the plague until you've figured out the ins and outs of the process. It's almost universally terrible stuff to hand solder with at first and takes a lot of getting used to. Just stick with the easy to use leaded solder and avoid breathing too much of it until you've got the process down.

Dirt cheap, low on features but OK quality: https://www.sparkfun.com/products/9141

Avoid the Wal Mart multimeter...I'm not happy to see a non category rated meter from GE of all companies. It's actually a rip off at $20....I've seen similar meters online for $5 and had the unfortunate experience of using one.

http://www.amazon.com/Extech-EX430-Autoranging-Multimeter-Capacitance/dp/B0000WU1AC

The Extech 430 is a good all rounder. It's Cat III with auto ranging and has bare bones capacitance and frequency counting. True RMS measurement allows you to measure AC things other than just 60Hz sine waves. (you need true RMS for checking amp output at 1kHz among other things) I own one and aside from the nasty yellow-green backlight and somewhat short battery life, it rocks. Comes with a temperature probe too, which you'll find useful.

If you're serious and want data logging without going all out on a $300-500 industrial meter from the likes of Fluke, give this a try. It looks cool as heck but possibly has a bit of a learning curve due to the menu instead of a dial. Cat III to 600V too. It does everything the Extech 430 does and more. https://www.circuitspecialists.com/dm620.html


Soldering Irons...

The classic pencil tip "fire starter": https://www.radioshack.com/product/index.jsp?productId=2062758&filterName=Type&filterValue=Soldering+irons

You get what you pay for there but I've fixed many things with ones just like this. Larger joints may need more heat, they make 40 and 60W irons for that. Tip life on these cheap irons is poor. Poor tips make poor joints. Replace them if they go bad. Do not sharpen one.

BUT...instead of having 3 low quality irons knocking around the shop, I recommend people go straight for an adjustable heat soldering station like this one: https://www.sparkfun.com/products/10707

Buy a couple spare tips if you order a soldering station. Local availability of these is nil. The stations usually have better irons, heat control that actually works and far better tips.

This soldering station and its more expensive digital counterpart, the WESD51 are a bit pricey. On the other hand, they're totally awesome and the gold standard in many shops: http://www.amazon.com/Weller-WES51-Analog-Soldering-Station/dp/B000BRC2XU

Once you get a station, you'll wonder how you ever got along without one. Good tools make the best repairs.

You are going to want to balance tools and parts.

TOOLS (must haves)

• Multimeters (At least two, I suggest starting with one cheapo ($5-$10) and one in the $30-$50 range)
  
• Variable regulated power supply with current limiting (Skip the cheap/dangerous chinese crap and get a used HP/Agilent/Keysight one off ebay like this or this.)
  
• Breadboards (several)
  
• Jumper wires
  
• Wire strippers and cutters
  
• Decent soldering Iron ($50-$100) (DO NOT CHEAP OUT ON THIS)
  
• Desoldering pump and/or wick (The ctrl-z of the soldering world)
  
• Heat shrink tubing for sealing connections (Especially if you are going to be doing outdoor stuff)
  
• Microcontrollers (I suggest starting with an Arudino Uno since it has the largest amount of online support material, you could get an Uno kit, any of them will be fine)
  .
  .
  TOOLS (eventually)
  
• Logic Analyzer (Let's you see the logic signals in your circuit which is super helpful for debugging, I have a bitscope micro which is decent, but the software kinda sucks and is more than just a logic analyzer)
  
• A function generator (variable voltage and frequency for sine, square and triangle waves) (Again I suggest used off ebay, something like this.)
  
• Oscilloscope (a really amazing tool for actally seeing what is going on in your circuit)
  .
  .
  PARTS (vaguely in order of usefullness)
  
• Elenco Resistor Kit
  
• Elenco Capacitor Kit
  
• Elenco Transistor Kit
  
• Elenco Diode Kit
  
• Elenco LED Kit
  (Of couse you don't have to get the Elenco kits, those are just the ones I use and really like)
  
• Voltage regulator ICs (Great for providing regulated power to things that need more than what your arduino can provide)
  
• Trimmer Potentiometer Kit (really useful to have around for many projects)
  
• Old electronic equipment to scavenge parts out of (Many of my parts have come from old equipment or broken ATX computer power supplies. Tearing stuff apart is both fun and yields great parts.)
  .
  .
  .
  I think that's all for now...

I bought the Wizard and I LOVE IT! It's plenty of power to start with some very solid components for the price. I wanted to build one myself as well... But then I found the Wizard.

I'll give you a list of the things that I bought along side the Wizard.

1. RunCam Swift 2 (https://www.amazon.com/gp/product/B01MY9IFJU/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1)
   
   
2. Quanum Cyclops V1 Headset (about 35$ on HobbyKing). The Quanum Cyclops is a wonderful headset for the price. The thing you need to watch out for when looking at cheap headsets is whether or not you get static or a bluescreen when you start losing signal. These headsets give you static. That is most certainly what you want. (https://hobbyking.com/en_us/quanum-cyclops-fpv-goggles.html)
   
   
3. Two clover leaf antennas (https://www.amazon.com/gp/product/B01M9IER0E/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1)
   
   
4. x3 3s batteries. (The other great thing about the Wizard is it's 4s ready for when you are ready for more power).
   
   
5. Keenstone UP100AC LiPo Charger. (https://www.amazon.com/Keenstone-UP100AC-Battery-Minimum-Balance/dp/B01JV826I0/ref=sr_1_1?s=toys-and-games&ie=UTF8&qid=1492193093&sr=1-1-spons&keywords=Lipo+charger&psc=1)
   
   
6. Parallel charging board (https://www.amazon.com/gp/product/B00UBOAXEI/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1)
   
   
7. XTronic Soldering Station (https://www.amazon.com/gp/product/B01DGZFSNE/ref=od_aui_detailpages00?ie=UTF8&psc=1)
   
   
8. FrSky XSR Receiver (https://www.amazon.com/FrSky-2-4GHz-Receiver-Output-Support/dp/B01HZB6XTI/ref=sr_1_1?s=toys-and-games&ie=UTF8&qid=1492193206&sr=1-1&keywords=FrSky+XSR)
   
   
9. FrSky Taranis X9D Plus (https://www.amazon.com/FrSky-Taranis-2-4ghz-ACCST-Transmitter/dp/B01D7QHB9G/ref=sr_1_2?s=toys-and-games&ie=UTF8&qid=1492193250&sr=1-2&keywords=taranis)

If you can build a Synthrotek Atari Punk Console, you can build a Shruthi-1.

The Shruthi-1 isn't hard, but you solder on both sides of both PCBs and there are a lot of parts. If you are a patient and methodical person, you shouldn't have any trouble. If you get frustrated easily, start with something simpler.

The right tools are key. Make sure you've got a PCB holder big enough to hold the Shruthi-1 boards. The Panavise 324 is a great investment if you plan on doing more DIY and repair work. A good soldering iron is key too. I started with an Aoyue 937+, but have since upgraded to a Hakko 888. Tweezers make picking individual components out of a pile much easier, and are cheap. Get a good set of small needle-nose pliers for bending resistors. Get a good set of diagonal cutters for clipping wires after soldering.

Update: The x0xb0x is a lot more work to put together, but about the same difficulty as the Shruthi.

Some tips I learned the hard way:

• Don't get a GoPro mount just yet. Chances are you probably won't even use it until you're a much better pilot, and it will just add unnecessary weight when you're not using it.
  
• Get an F3 based flight controller (SP Racing F3 or similar) instead of an F1 (Naze32). If you're anything like me, you're going to try to get the most out of your quad and use all of the fancy technologies available to you (like an on screen display, or using SBUS and telemetry with your receiver, or LEDs, or whatever). When you go to add stuff on, though, you have to work with hardware serial ports, or UARTs; the Naze32 has 2 UARTs while F3 FCs have 3 available. Having that extra UART available will make a lot of things a lot easier, and the increased processing power on the F3 should allow you to use more software serial ports than on the Naze (meaning you can use more stuff simultaneously).
  
• When assembling your quad, make sure you put your screws through the plates facing downwards with the nuts on the ground. It's a lot easier to use a socket wrench to tighten stuff than a hex wrench.
  
• If you're building a 250 quad first, use 220X motors instead of 180X motors. The 220X motors are bigger and produce more thrust than the 180X motors, which will improve your flying characteristics. Just make sure that the frame you choose can accommodate them; if you're starting out with a tried and true ZMR250, make sure you get the version with M3-sized arms.
  
• Make sure, among other things, you have the following equipment:
  
  
  • Soldering iron with a fine tip (these are replaceable, so if you already have an iron you can just get the tips). One with adjustable temperature helps a lot.
    
  • Solder
    
  • Soldering flux (I recommend a flux pen; you can get these from Amazon)
    
  • Desoldering wick
    
  • Solder tip cleaning wire
    
  • Soldering iron holder
    
  • Multimeter (useful for testing stuff). Make sure to also get a battery for it.
    
    
• If you're planning on using LEDs, get addressable LED strips (WS2812 or equivalent). Since my ZMR uses nonaddressable strips, I have switches on the strips, which tend to get damaged in rough landings.
  
• Get a spare motor in each direction and a spare ESC. You don't know when you'll break something, but when you do, you'll have a spare you can quickly switch out.
  
• Heatshrink looks better than electrical tape.
  
• Zip ties are your friend.

$14 link for a solid basic soldering iron.
Here's one that costs a little more, but has more adjustability $39 link.
Anything from Weller is going to be pretty good.
Here's a pretty good basic soldering video.
It's not hard, but takes a little practice to get the feel for it. I would recommend finding a broken electronic that you can pull a circuit board out of and just practice soldering by removing parts from the board and putting them back.
Have fun!

I have this one. It's not great, but it's been good enough for my purposes for a few years. It's about $40.
https://smile.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC/

There are ones on Amazon that are a little cheaper. This one sounds pretty comparable and is in your price range.
https://smile.amazon.com/Aoyue-Variable-Soldering-Station-Removable/dp/B00MCVCHJM/

For really basic soldering, you actually can get away without a temperature control, but it's hard to recommend that for anything involving a printed circuit board.

For my part, I'm thinking of upgrading to a hot air reflow station, to make it easier to work with solder paste and surface-mount components, as well as heat-shrink tubing. But the basic adjustable Weller was good enough for several years of tinkering.

You can get okay ones for $50-100. Are you looking for a soldering station or just a soldering pencil/gun?
I would recommend a wall unit, as opposed to a butane unit, because butane ones are mainly for people soldering in the field. They are nice and portable, but you have more wall outlets than butane canisters in your place, so it's easier

..





Weller and Hakko are great brands, their tips are a bit pricey too, but trust me, they last a lot longer than the cheap irons and their cheap tips.
You can't go wrong with any of these:
Weller
Hakko




Feel free to ask me other questions.

The cheapo 30W irons are certainly capable of soldering a board, they're just a little rougher to learn with. In my opinion they're great tools to have in a go bag for field repair but they're crap when you have access to something better.

If you can, try to find something that feels good in the hand and has some form of temperature control. A lot of the ones that just plug in jump straight up to 750 degrees which can damage circuit boards if you're not careful.

Personally I use a Hakko FX-888D, but that cost was sunk as a business investment a few years back. There are some nice cheap stations on Amazon though. This one looks pretty solid for the price. https://www.amazon.com/gp/aw/d/B00MCVCHJM/

• Get an arduino starter kit and start building projects.
  
• This is a good one for a good price.(it's twice that or more on amazon)
  
• and this is a good price for a batch of sensors(no arduino included)
  
• if you want to move stuff a batch of servos is fun
  
• a soldering iron is good
  
• this one is good for the price. I don't like the ones that adjust at the handle. I prefer a base station.
  
• need solder as well
  
• and a solder sucker
  
• flush cut wirecutters are good to have
  
• a good pair of wire strippers is a life saver
  
• Good idea to have a multimeter around for verifying resistance values and voltages
  
• this is a decent one for the price
  
• Need some breadboard for prototyping. I'd suggest at least 3
  
• and some protoboards to finalize your circuit(until you start getting pcb's made)
  
• some solid conductor wire
  
• I like these storage cases for keeping my mess semi-under control.
  
  That's about all I can think of for now.
  

I'm pretty new to soldering, but I picked up a Hakko FX-888d and love it. It's got 300+ great Amazon reviews and only costs $100. Any complaints I saw were about it being complicated to set the temp, but this was not my experience at all.

http://www.amazon.com/Hakko-Digital-FX888D-Soldering-Station/dp/B00AWUFVY8

Edit: Yeah, the color makes it look like a toy... But I assure you it is not.

I'm still pretty new to this myself, but like you I have some electronics experience in the past. I just got this Weller 40w iron station with a desolder braid/sucker and a solder tip cleaner. Oh and a more precise tip for the solder iron

I'm really happy with it all so far, and couln't imagine needing more for a while. A heat gun would be nice for de-soldering and reflowing premade boards (like modding Boss pedals), but that can also be done with a regular solder iron as far as I know. You can get the above for about $60 total, so it's a nice way to get your feet wet without a huge investment. Then you gotta add on components/enclosures/pots/switches etc. Maybe get a helping hands and/or circuit holder if you need

Oh and get a good multimeter. I went a step up from the $20 ones and got this one which I'm also really happy with.

Practice is everything. I could barely solder a cable but decided I wanted to start building up a few preamps from kits.

A solid, variable temp iron like this Hakko, some mounted alligator clamps and a magnifier are all solid investments.

But most importantly, practice. Go find some old battery operated toys or keyboards and practice desoldering and resoldering on a pcb is a great way to learn to steady your hand. If you want to learn some basics of circuit design, maybe tackle a GroupDIY project like a G-SSL comp or similar (plus you'll have a bomb-ass compressor).

I suggest this:

http://www.amazon.com/Elenco-Practical-Soldering-Project-Kit/dp/B0002LUAL6/ref=sr_1_4?ie=UTF8&qid=1406761425&sr=8-4&keywords=learn+to+solder+kit

It's a very good kit, and will give you plenty of practice before you solder your Poker 2. No frills, and will give you plenty of practice for through hole soldering.

Combine this with a practical, but good quality soldering station:

http://www.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC/ref=sr_1_3?s=power-hand-tools&ie=UTF8&qid=1406762091&sr=1-3&keywords=soldering+iron

A desoldering pump:

http://www.amazon.com/Sucking-Vacuum-Desoldering-Solder-Remover/dp/B005GIPKOW/ref=sr_1_3?s=hi&ie=UTF8&qid=1406762167&sr=1-3&keywords=desoldering+pump

And some solder:

http://www.amazon.com/Alpha-AT-31604-60-40-Solder-Ounces/dp/B00030AP48/ref=sr_1_1?s=power-hand-tools&ie=UTF8&qid=1406762345&sr=1-1&keywords=solder

To learn, there are plenty of Youtube videos, I recommend you also solder the Elenco kit, then desolder everything to get a feel for how the desoldering pump works (it's super easy, you can't really screw it up). Then, solder it together one more time for extra practice.

All together, about $66 bucks. Add in the cost of the switches, and you're looking at a little over 100. Still a bunch cheaper than the Poker 2 from Massdrop ($143.50), and you've just learned a life skill. For me, that's totally worth it, but then again, I'm an engineer, and learning useful skills is what my entire profession is based on.

---

EDIT: Get this soldering kit instead:

http://www.amazon.com/Elenco-SP3B-Practical-Soldering-Project/dp/B0002LUALG/ref=pd_tcs_compl_t_3?ie=UTF8&refRID=00RQRQTCJ767WDS4D7KV

Cheaper and has more soldering points. The other one has a shitty speaker which doesn't add much to the soldering lesson, but drives the cost up.

These types of things are generally considered hobbyist level and in all honestly, you are best doing this yourself with a good Weller Soldering Iron, a 56 SMD Desk Magnafier and some helping hands.

If that is out of the question though, I'd recommend checking out Fab Lab. It is a non-profit community space that has all the equipment available to anyone who dabbles in everything from Raspberry Pi to all things electronics. You may be able to consign someone or do it yourself there.Their address is 847 14th Street, San Diego 92101

Hope this helps and good luck!

Not at all. While it's not impossible to use a cheap soldering iron and get a good job done, it will save you a TON of hassel by getting a good one. RadioShack irons are more trouble than 2x what they're worth. My soldering jobs have been a pleasure to do since I upgraded, and I solder often so that's important to me. I use the Weller WESD51, and it's an absolute joy to use. If your on a bit more of a budget, my friend is a professional luthier and he's never complained about the WLC100, which is also from Weller.


Do it. It's worth it.

I absolutely agree that a variable temp iron is better. However, OP made it sound like they were on a pretty tight budget and I couldn't in good conscious recommend >>SOMETHING LIKE THIS<< that would take up their entire budget. Especially since they are just learning and they might decide they don't like it (learning to solder well takes patience and a fair bit of dexterity...... high reliability soldering course was one of the most frustrating courses I took during my technical training).


Having said all that, though, I've done a fair bit of work in the field using one of those portable butane irons. You just have to be careful and know what you're doing. :)

Those little vises are freaking magic. I see those helping hands clip things all over and never have I preferred one over a proper articulating table vise.

Soldering iron: https://www.amazon.com/Hakko-FX888D-23BY-Digital-Soldering-FX-888D/dp/B00ANZRT4M

Edit: most people recommend getting a chisel tip for the soldering iron. Big tips for big jobs, small tips for small jobs. Just having the pencil tip and one chisel will get you by for a long time.

Desoldering braid: https://www.amazon.com/Aven-17542-Desoldering-2-5mm-Length/dp/B003E48ERU/

Desoldering pump: https://www.amazon.com/WEmake-WM-SP4-Solder-Sucker-desoldering/dp/B0002KRAAG

You want both the pump and the braid. Get thin solder for electronics. You should probably use lead-free, but I like good old 60/40.

There are a ton of suggestions on multimeters. The exact right one for you depends on what you eventually want to do. Dave Jone's EEVBlog has some good suggestions. As does Adafruit. Anything Adafruit recommends isn't too far off the mark. If you just want a suggestion: Extech EX330 for $45 https://www.amazon.com/Extech-EX330-Autoranging-Multimeter-Thermometer/dp/B000EX0AE4 Cheaper ones will do the job, but this is a better one. The next step up are True RMS meters for about $100.

You guys are making it sound easier than it is.
SOLDERING is easy. Anyone can do that. Just heat the work and the solder drips right in the hole.

It's DESOLDERING which is hard. And without proper desoldering equipmenet (like an Aoyue or a Hakko), it can be even HARDER and if you do it wrong, you could damage the PCB. You need more than just a soldering iron to desolder. You also need a desoldering pump (vacuum tool pump (NOT recommended unless you have no other choice) or a proper desoldering iron which is $$$).

The key is probably damaged and those are not easy to fix without making the problem worse. If the metal tab is damaged or bent out of shape there's no fixing that. With a switch top remover (from MK.com) you can remove the switch top and the cherry stem, after desoldering the switch (ONLY PCB mount switches can be popped open without desoldering), but if you don't have spare switches, I would just RMA the thing.

A good desoldering pump is https://www.amazon.com/Aoyue-Contained-Desoldering-Internal-Carrying/dp/B00PGFAJWS
But as you can see it's expensive. But it does come with some extra tip tops.

An even better one but more expensive is https://www.amazon.com/Hakko-FR300-05-P-Desoldering-Tool/dp/B00KWM69C4/ref=sr_1_1?ie=UTF8&qid=1490577663&sr=8-1&keywords=Hakko+FR300-05+desoldering+tool

Yes that's $$. And a lot.

A good starter kit, which includes solder and a vacuum pump is https://www.amazon.com/gp/product/B01E1ISGH0/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 ; not too expensive for what you get.

Once you're ready to move up to higher quality you can buy this:
https://www.amazon.com/Hakko-FX888D-23BY-Soldering-Station-599-029/dp/B00C2BHTBI/ref=sr_1_3?ie=UTF8&qid=1489522270&sr=8-3&keywords=Hakko+FX888D

I used these guides to help plan and build this.
https://docs.keeb.io/build-guide.html
https://github.com/nicinabox/lets-split-guide

I got the majority of my keyboard parts such as the diodes, case/plates, pcb, and TRRS jack/cable from keeb.io, and sourced the pro micro and switches from mehkee.

The Let's Split and the Nyquist are basically the same, but instead the Nyquist has the extra row, allowing numbers to be on the base layer.

Before starting the build, you'd want to get an adequate soldering iron. I didn't have the funds to get a Hakko FX888D when I got into this with my Clueboard, so I instead bought a Station 60 and a 2.4mm Chisel tip to replace the included tip. Don't forget the solder wire! I used some old solder wire that I found laying around, but something like Kester 44 63/37 solder wire will serve you well. Fairly thin solder wire around .031" will be adequate, but some people use thinner ones; it's all preference. Just avoid lead-free solder, they are a pain to solder with. If you think you will mess up, I recommend either getting some soldering wick or a desoldering pump. I heard that desoldering irons are also pretty good, but I never tried one to give a proper opinion.

Then you want to check out a tutorial regarding soldering, if you don't know how to do it already. I learned from EEVblog (warning: it's a lengthy video!), but you can probably find some other video about it.

After you have all your parts and double checked the parts list, you can start building. It's pretty much just following the guides step by step. The Let's Split guide that I linked is the most detailed for the build process, but the official Nyquist one seems to still be under construction at the time I am writing this. If you have any trouble, you can contact bakingpy here on reddit or on keeb.io, or just make a thread here or on /r/olkb. Someone will help answer your questions!

Without the keycaps, I spent around $75 on the project. Overall, around $150.

Edit: cost

Hey! Glad to help. This Is the exact soldering iron I use. Extremely effective, I keep it at a 3 at all times, seems to be a legit temperature for everything Gameboy related.

The Solder I use works really well, rarely sticks to the soldering tip (like many other ones I've tried) and seems to be the most consistent. It's also supported by HHL - so you know it's solid!

Hope that helps.

i'm gonna go with what everyone else says: get a decent temp adjusting iron. it makes a world of a difference...add to that a small chisel tip (usually not provided on a cheap pen iron)...such much easier and enjoyable soldering. though, its not worth spending 80-300 dollars on a soldering iron for one project..

i use/recommend:

• an x-tronic station/iron $90 sponge+light/magnifier+tips+replacement heat element
  
  
• a hakko soldering tip cleaner $10
  
  also another good affordable iron:
  
  
• hakko fx-888 station/iron $90 sponge+cleaner
  
  everyone says weller...and its because they dropped the money on one and want other people to do the same haha...if you have the money, sure go for it. if not, many stations in the 80-100 range are excellent quality to begin on.
  
  also get a helping hand, tweezers, needle nose pliers, snips, and maybe a wire stripper.

I appreciate the effort. This seems promising and may be the better idea, the other route I was going to take was the Bardwell kit with some other stuff.

https://store.rotorriot.com/bardwells-budget-build-kit/

https://www.racedayquads.com/products/rdq-series-1300mah-4s-100c-fpv-lipo-battery

https://www.amazon.com/usmile-receiver-Support-FS-iT4S-Evolution/dp/B07FMFG6Q3/ref=sr_1_1?s=toys-and-games&ie=UTF8&qid=1542217789&sr=1-1&keywords=fli14

https://www.amazon.com/Flysky-FS-i6X-Transmitter-FS-iA6B-Receiver/dp/B0744DPPL8

https://www.getfpv.com/new-arrivals/ev-peak-e3-falcore-edition-35w-3a-lipo-battery-balance-charger.html

https://www.amazon.com/dp/B01N4571Q6/ref=as_li_ss_tl?psc=1&linkCode=sl1&tag=fpvknowitall-web-20&linkId=6769f39dd3014cb5619db31a54b18438

https://www.racedayquads.com/products/rdq-quad-solder-38-62-0-8mm-100g

https://www.amazon.com/DOWELL-Stripper-Multi-Function-Tool%EF%BC%8CProfessional-Craftsmanship/dp/B06X9875Z7/ref=sr_1_4?s=hi&ie=UTF8&qid=1542221619&sr=1-4&keywords=wire+stripper+and+cutter

https://www.amazon.com/NEEWER-Titanium-Nitride-Driver-Wrench/dp/B00CP2GGBI/ref=as_li_ss_tl?ie=UTF8&qid=1488911480&sr=8-3&keywords=hex+driver&linkCode=sl1&tag=dre-youtube-20&linkId=d53d845db871ab90fe110b2918f60a7e

$381 no shipping/tax and the build kit comes with accessory kit including motor screws for CL1 5mm thick arms, double-sided tape, FC stack mounting screws, XT60 power lead, zip ties, and heat shrink.

​

Your idea seems like it may be "too little" for the project but I am honestly ok with that because I rather get something done then bite off something too big to chew and end up having to figure something out last second and it being a piece of crap.

​

So does that flight controller stick right into those frames and then you screw them in or something? You say I only need to solder the the power wires to the camera, where do the motors go? I probably sound like an idiot but I'm not really an electrician or carpenter, I don't build things, other then computers :P. I need to head off now so I can't do so much research right now and I spent all day researching today.. won't have much time tomorrow, we are going to tour a college. Can you recommend a good video that would go along with this build? Tomorrow, I am going to ask the teacher if the TV in the room I am presenting in has analog input, if not we go from there. We have access to a 3D printer but a lot of people are going to be using it most likely and I think its slow but I can definitely get the camera mount printed. Once again, appreciate the effort.

I have the hot air only version of the first one, the 858D. It's okay, gets the job done. I got it on the recommendation of a friend who uses it all the time and is really happy with it.

For a soldering iron though, IMO you'd be better served by something name brand like the Hakko FX888D or the Weller WES51. I have the WESD51 and it has served me well. For J Random Soldering Iron, the temperature control might not be very good, and it might be tough getting different tips.

A decent budget option might be a hakko 936 knockoff, which should have pretty good availability of replacement tips.

That set up will do all right.

Helping hands are good, solder looks fine (although if you do a lot of soldering you'll burn through that quickly), and the wick is fine.

One other thing you should get is some flux (probably paste or liquid, maybe someone can recommend a specific flux?). Flux makes soldering a million times easier if the parts are dirty.

Soldering iron wise, that's an alright iron. The tip it comes with is fine for large/medium components. However, consider how much soldering you plan to do. Is it a lot, possibly on small things?

Both the Weller WES51 and the Hakko FX888D are both popular, quality soldering irons. Basically, the handles are smaller (easier to control and maneuver), and the temperature is regulated (more consistent/stable). Additionally, the range of available tips with the WLC100 is not as large.

In conclusion, that's a perfectly fine setup (with the flux), but think about how much you anticipate soldering in the future and considering a higher quality soldering iron. Hope that helps.

Machined hex drivers; I've had a set of Dynamite Machined ones for 4 years now and only have had to replace the tip once when I dropped the 1.5MM one onto concrete. Do NOT buy the anodized ones, those use soft metals that will wear down easily. Also, a good soldering iron isn't required, but it sure as heck makes everything a whole lot easier. I'd also suggest some basic nut drivers like 4-7MM almost like these. A magnetic parts tray will also make your life easier.

https://www.amainhobbies.com/dynamite-machined-hex-driver-us-set-red-dyn2909/p38304
https://www.amainhobbies.com/dynamite-machined-hex-driver-metric-set-red-dyn2904/p38303
https://www.homedepot.com/p/Klein-Tools-5-5-mm-Metric-Nut-Driver-with-3-in-Hollow-Shaft-70255/203310642
https://www.amazon.com/Weller-WES51-Analog-Soldering-Station/dp/B000BRC2XU

First of all you want a soldering iron, not gun. I use a Weller WES51, it's on sale at Amazon for $92, and is the as good as the best I've ever used.

http://www.amazon.com/Weller-WES51-Analog-Soldering-Station/dp/B000BRC2XU

Note, I had a Stahl Tools copy of the Weller WES51, and it is a hunk of junk.

I grew up using Wellers, and they've worked flawlessly for my entire life.

I can also recommend the Hakko FX-888 - I don't see a need for a digital readout.

I also recommend Kester 44 rosin core solder (.031"), it's excellent.

I'll just recommend these:

https://www.getfpv.com/ts100-digital-oled-programmable-interface-mini-soldering-iron.html <----- Fantastic portable and desktop but best if you need portable. I own this one.

https://www.amazon.com/Aoyue-Variable-Soldering-Station-Removable/dp/B00MCVCHJM?ref_=ast_bbp_dp60W so you can split the diff.

https://www.amazon.com/Aoyue-9378-Programmable-Digital-Soldering/dp/B00BSW69LI?ref_=ast_bbp_dp <---- I own this one. Works very very well.

Never owned a Weller that I've liked.

No, that's overkill for what I do.

I since won a hackaday contest and got an amazing Weller soldering tweezers and iron. It's not fancy like what you posted (although if I did a lot of repair, I'd absolutely want that preheat and hot air) but it's so well designed it's never disappointed me. With only the one soldering iron, it'd be around $250 I think.

I did more teaching on cheaper, $50 soldering stations like this and I almost never can tell the difference. I recommend anybody getting into soldering pay around $50, doing a bit of research to make sure you don't get the worst $50 iron possible. Unless you really dive deep into the smallest, or most tricky components, anything adjustable that's significantly over 50 Watts (certainly not 25!!!) feels about the same as any other.

X-Tronic Model #3020-XTS Digital Display Soldering Iron Station - 10 Minute Sleep Function, Auto Cool Down, C/F Switch, Ergonomic Soldering Iron, Solder Holder, Brass Tip Cleaner with Cleaning Flux https://www.amazon.com/dp/B01DGZFSNE/ref=cm_sw_r_cp_apa_O6hHAbF8GP2MB

Well, I really want to say that it's not worth it if you don't have a soldering iron, but having an iron opens you up to modding. I personally would buy this iron to start Weller WLC100 40-Watt Soldering Station https://www.amazon.com/dp/B000AS28UC/ref=cm_sw_r_other_awd_a-b5wbP6YPKQS

It's a decent iron and then you can buy a DMG and put in a bivert mod! Also, don't forget to tin your tip or else it slowly corrodes when the iron is hot. These are the starter irons in the electronics shop at my school, a technical high shool. And if you get bored you can always poke holes in the power supply with the hot iron!/s If you have a lot of money then buy the iron I have, a Weller WES51. Soldering irons can also fix jewelry and other metal, so it's not a one time use purchase. And if you get burnt you don't even feel it, I don't think I have nerves in my right index finger anymore!

Replacing the batteries is very easy. They go for $7 for 10 on eBay just search Gameboy save battery. Only Pokemon RSE need them for GBA games because of their clocks. They use CR1616 batteries. No other GBA games need batteries AFAIK. Most original or color game needs them for saves, however. They use CR2032 batteries. It's easy, just make sure that the positive and negative are correct. Positive side is shiny with writing on the battery and the negative is textured. Earlier GB games such as Kirby's dreamland, Tetris, Pinball, etc require no save battery, as they didn't save!

Essentially, yes - they're probably too cheap.

If you want good cables, you've got to pay up.

Best Solderless:
https://reverb.com/item/1423315-evidence-audio-sis-pedal-board-kit-10-plugs-10-feet-black-monorail-authorized-dealer

Or learn how to solder.

Buy this best soldering iron: https://www.amazon.com/dp/B00ANZRT4M/ref=cm_sw_r_cp_api_oS34ybN5TT4V3

With this: https://www.amazon.com/dp/B003UIC78W/ref=cm_sw_r_cp_api_dT34yb2BTQYXY

And this: http://www.redco.com/Mogami-W2319.html

Money well spent. Patch cables will cost you about $4-$5 to make and make excellent Christmas presents for friends and family.

I've got nothing but good things to say about my Weller WES51 which comes in just under $100. Heats up from cold to temp in about 30-40 seconds or so. Can also hot-change tips if you've got something like a good silicone mat to unscrew the threaded holder. I really can't say anything about other temp controlled stations like Hakkos or [insert your favorite brand here] since I've had my Weller for several years without issue. I pair it with a cheap desoldering pump and a dedicated old cheap desoldering iron.

I've gone through about a half a dozen of the $5-$15 radio shack irons before I finally decided to spend the money on a nice one. I had no idea what I was missing!

There are a few types. The cheapest one is just a hot pencil. You plug it in and it gets hot. It's not adjustable at all - it just gets up to whatever level of power it draws, regardless of the work it's doing. Typically they cycle between not-hot-enough and way-too-hot for whatever the job is. :-)

The second-cheapest kind is the same thing, but with a little selector switch, so you can switch between low and high. I think one of mine was 5W/15W. Same as before - it's a power level, not a temperature.

Third type is the same thing, but with more adjustments. You can vary the heat more accurately, but it's still only by power level, not actual temperature.

The good kind is the kind that measures its own temperature and tries to maintain it. You can turn the dial to the temperature you want, and no matter what the work is, it will heat up as needed to maintain that temperature.

I have the WESD51 (Digital display, adjustable temperature). It was expensive, but I got a good deal on it (only $10 or so more than the analog version). I was really sold on the temperature controls, and it makes a huge difference.

You'll have to carefully read specs to see if "Adjustable" means adjustable POWER or adjustable TEMPERATURE. Some irons will even say that they are adjustable temperature, but really they are just a hot-cold knob that adjusts power.

I shouldn't recommend a specific iron, since the only ones I've used are the terrible $5 ones and the WESD51, but I've heard good things about the WCL100. It seems to have decent reviews. If you can't justify the $80+ for a temperature-controlled iron like the WES51 or WESD51, look into this one, since it's only $40.

EDIT: I take that back! I should have listened to myself and NOT recommended it. As soon as I read the reviews I discovered that you can get a constant-temperature iron for around the same price! Something like This 850F or this 750F. In short - do your research! Temperature controlled is key!

ANOTHER EDIT: The work I'm doing is generally through-hole components and similar small electronics. I leave the temperature dial at around 700F most of the time. So if $80 for a true adjustable-temperature soldering station is too much to swallow, save money by getting a constant-temperature iron at the temperature you want, instead of getting a shitty adjustable-wattage iron.

Yes, a soldering station will give you better overall performance. The issue is at your current budget I can't recommend any particular brand. I own a Hakko FX-888 that I'm in love with, but that's around $95. If you can swing it, that'll be a purchase that will last you the rest of your life with proper care. The cheaper stations I have no experience with, and the quality control is what I'd be concerned about.

https://www.amazon.com/X-Tronic-3020-XTS-Digital-Display-Soldering/dp/B01DGZFSNE/

This guy looks decent, but like I said I've got no personal experience with it.

To reiterate, you will get 100% better performance with a station compared to the TS80. If portability isn't an issue then go for a station. You'll probably have a better time getting an assortment of tips for the station compared to the TS80 as well.

Thanks a lot for the comment. So when you say Weller soldering station, you mean something like this and not this which was suggested earlier. I can't seem to tell if the latter is adjustable (packaging seems misleading) but I'm assuming not. If the first link has your thumbs up I'll probably go with it because the price is totally doable, it's adjustable between 5W and 40W, and it looks pretty cool IMO.

Love your work btw!

If you're interested in getting into soldering, get a few cheap kits like battery powered light up gadgets and the like. They're usually around like $10, so it's not that big a deal if you break them while you're learning to solder. Next, a hands free solder station and a proper soldering iron make all the difference. The hands free option is the cheapest of the cheap and the iron is just a personal preference. Being able to control the heat of your iron and keep your board accessible is super useful. I ruined a couple of PS2s being cock-sure with an $8 iron and no practice.

If you don't already have one, get a soldering station. A Hakko 888 or Weller WES51 is an affordable option and will massively improve any soldering job. This is one of the good examples of how the quality of the tool has a direct effect on the quality of the work, even if you're an amateur.

If you can't see laying out that cash, just try at least to buy this one. I'm sure there are other options also.

EDIT: In case it's not perfectly clear, and for the peanut gallery:

A soldering iron is a perfect example of what a good tool can do, and what a bad tool will stop you from doing. In the hands of a wizard, a shitty iron can still create passable solder joints. But a good soldering iron will allow a rank amateur to make good, quality joints. And an amateur with a bad soldering iron? Nothing but junk will ever result.

A good iron and good light will save many jobs. If you're going to put money anywhere, let it be in tools and lighting.

Do you plan on doing plenty of soldering in the future or is this a one off job? A decent soldering iron makes a night and day difference when it comes to working on electronics. I've used the cheap $10 ones you can buy from hardware stores and they've always ended up being difficult to work with.

I'd recommend a weller WES51. They're a tad bit pricy, but you can get interchangeable tips and it's temperature controlled. I've had mine for 2 years now and it's absolutely fantastic.

You'll probably want to use some thin rosin core lead solder. You should be able to buy this at your local hardware store.

If you plan on doing any sort of reworking, copper wick is super useful for removing solder. A cheap solder sucker is also nice to have for removing larger blobs of solder.

Weller WES51 Amazon link

Yes, soldering stations are a ridiculous improvement over normal soldering irons! If you get the cash to splurge a little, Hakko makes great soldering stations. The FX-888D is a great entry level soldering station for about $100, which is still pretty much on the low end for soldering stations. But you should be able to find one on Amazon a little cheaper, closer to $90. However low end soldering stations are usually perfect hobbyist stations.

edit: Found one!

You definitely want to get a soldering station. So something that can control the temperature of the of the iron. The reason being is the ones that just plug into the wall usually fluctuate between extremely hot and very hot which can become if you’re trying to solder next to very delicate transistors on the pcb.


I know people say you can get away with the cheapest everything but that’s usually not the case at all and sometimes dangerous to your health.


Getting good solder, tip tinner, brass sponge, flux pen, and a fan with a carbon filter will do you great things.


The fan is extremely important when your desoldering as that will give off a tonne of chemicals.


This is what I personally have


https://www.amazon.com/gp/aw/d/B00BSW69LI/ref=ya_aw_oh_bia_dp?ie=UTF8&psc=1

https://www.amazon.com/gp/aw/d/B074J6R1KQ/ref=ya_aw_oh_bia_dp?ie=UTF8&psc=1


https://www.amazon.com/gp/aw/d/B001W2XZOS/ref=ya_aw_oh_bia_dp?ie=UTF8&psc=1


https://www.amazon.com/gp/aw/d/B00FZPGDLA/ref=ya_aw_oh_bia_dp?ie=UTF8&psc=1


https://www.amazon.com/gp/aw/d/B00NS4J6BY/ref=ya_aw_oh_bia_dp?ie=UTF8&psc=1


The soldering iron is overkill if you’re just using it for trains

I've purchased this cheap 60W Aoyue one for $30 here in the US through amazon. It has served me well for the amount I need to do with my personal electronics. I also purchased a set of interchangeable tips that are nice for the flexibility. The only thing I wish this had was an actual temperature reading, which is where the suggestion by /u/abw looks like a better set, and would be better if you are planning to get quite a bit of use out of it.

Trust me when I say: variable temperature makes a big difference. I have a knockoff of the Hakko 936. The closest thing on amazon.ca is this Aoyue, which I've heard good things about. You don't need hot air as a beginner (or even for most surface mount work), so don't go to the top of the line. You can get cheap rosin core solder to get started. FYI, every set of helping hands like these I have ever owned have been absolute garbage. The vise suggested by /u/rykki will be dramatically more useful, even though it will cost more. (But it might also have applications outside of soldering.)

That's waaaaay overkill in my opinion. Don't spend that much on something you're gonna use once a year or something. I treated myself because I solder several times a month and got this guy.

And if you plan to only do kits where you only have to solder switches, you can literally do that with a $5 RadioShack iron (my friend did that for his MiniVan). Switches are pretty much the single easiest thing to solder. They're huge and very heat-resistant. If you want to do, for example, surface-mount diodes, you might want something heat-controllable, but any junk will do for switches.

BUT GET GOOD SOLDER. In particular, most stores sell 60/40 (60% lead, 40% tin) solder. 60/40 solder is awful. 63/37 solder is way better because 63/37 solder melts at a lower temperature and its melting point is one point instead of a range of temperatures where it's partially solid. Kester 44 63/37 is some of the best.

Lots of great options. This is great if you change the temp a lot or forget to turn it off. This is great if you never change the temp (like me). This is great if you're on a tight budget.

Whoo, loaded question with tons of opinions, hah.

The "best" lube is highly subjective, and it also depends on the type of switch. If you're lubing linear switches, my personal favorite is VPF 1514 oil. It's not cheap, but it gets the job done (you can order smaller quantities of it from Mehkee. For tactile switches, I use Krytox GPL 205 (which you used to be able to buy DuPont brand on Amazon, but no longer appears to be available).

Best solder for building keyboards is Kester, 0.8mm, hands down. Quality stuff, flows and bonds well, and the size is good for switches or LEDs.

Soldering iron recommendations: This cheap kit is acceptable for building a keyboard (I built 4 or 5 with it prior to upgrading). If you know you're going to be building multiple kits, and you think it's possible you might do re-work or try to desolder boards, just go ahead and spend the money right the first time and get this one: Hakko FX888D. Basically the gold standard of soldering irons.

The capacitor was nothing fancy, just a 2200uF capacitor. Apparently that one capacitor tends to be a bit of an issue in that model of player for whatever reason...

I'm pretty sure that the iron I have is this one along with a holder that looks just like this one, though I'd have to go double-check the iron to be sure that's the one I have. Seems to work pretty well, and you can replace the stock tip with this little pointy one to work on small stuff better.

It's a fairly simple process. Just open the game, desolder the old battery, solder the new one, and close the game.

Make sure the new battery is the same type as the old one; a CR2032 probably won't fit in a game that uses a CR1616. Make sure the batteries you order have tabs. It's generally not a good idea to solder directly to batteries, so the tabs make it much easier to mount. As for the batteries themselves, just find an eBay seller with good feedback and you should be fine.

Take your time and be careful, and you should be able to do it just fine. If you're worried you'll mess it up, watch some soldering how-to videos and practice on some old junk board before you move on to a Gameboy game. If you don't already have a soldering iron, the Weller WLC100 is a great, inexpensive, variable-temperature soldering iron that is frequently recommended here. I have it and it works perfectly. 60/40 rosin-core leaded solder should be fine for this; it's what I've used for my cart battery replacements and I've had no issues with it.

PACE makes great soldering workstations and Weller is probably the most popular consumer brand. I personally use a cheap soldering iron I got off of Amazon for around $15. I think it works fine and allows me to control the temp. There are much better options out there for more intensive work. I only use mine a couple of times a year and that's usually for hobby electronics work. It's more than adequate for that level of use.

This is the one I have -
http://www.amazon.com/Stahl-Tools-SSVT-Temperature-Soldering/dp/B0029N70WM/ref=sr_1_8?ie=UTF8&qid=1452181798&sr=8-8&keywords=Soldering+station

If you're planning on doing a lot of de-soldering, you'll either need a de-soldering station OR solder wick. I use copper solder wick and it works great. Do not buy one of those cheap de-solder irons with the red bulb on it or the pen device that sucks out the melted solder. I've used both of those and they're pretty crappy. Solder wick is the way to go. Buy some and you won't regret it.

For replacing surface mount devices, you'll need an SMD rework station and I don't have any suggestions on those.

As far as PC repair kits go, most of those pre-made kits are pretty over priced for what comes in them.

Go to Harbor Freight and buy:

I've used a few of their precision screwdriver sets. This is the one I prefer

http://www.harborfreight.com/hand-tools/screwdrivers/33-piece-precision-screwdriver-set-93916.html

Get one of those 4-in-one screwdrivers. The bit socket will also remove case screws.

Get seperate T-15 and T20 screwdrivers. you'll need these for larger items like legacy Compaq case screws and printers.

Wrist strap - there is some debate about this and it depends on the region you live in as to how much static electricity actually builds up on your body. I never wear one and I've never killed any devices. I have heard that there are places where you would be stupid not to wear one.

Grab a telescoping magnetic screw retriever thing. Don't worry, the amount of magnetism in those things will not harm a PC.

Flashlight

Needle nose pliers

Small and Large Side cutters

Cable ties

CAT5 & 6 Cable testers

This should get your started and most of these items are a couple of bucks or less at HF. I know they make crappy tools, but for computer repair they do fine. You're not repairing a diesel tractor-trailer.

I'm sure I've left something out or someone will have some better ideas. Comments and constructive criticism is welcome.

http://www.amazon.com/Aoyue-937-Digital-Soldering-Station/dp/B000I30QBW/ref=sr_1_15?ie=UTF8&qid=1395077736&sr=8-15&keywords=soldering+iron

get a good iron, solder, and those magnifier hands. Then just start playing with soldering wire together and then do a project. Search youtube how to solder it's pretty easy. Oh and wear safety glasses sometimes the wire will slip or something weird happens and solder goes flying towards your eyes, better to be safe than sorry.


http://www.amazon.com/SE-MZ101B-Helping-Hands-Magnifying/dp/B000RB38X8/ref=pd_cp_hi_1

Hey, best tip i can give you to get better is to find junk printers, motherboards, ect... and just practice de-soldering and re-soldering caps, resistors, anything that just has two pins. Also I would also suggest lowering the temp on the Iron (if you can) I use about 320 C for most of my stuff, and I would also recommend getting a good soldering iron it helps a lot. The soldering Iron I would recommend the TS100 with the D24-Tip, then look online for how to set it up.
If you like you can contact me by discord, and I can help you with what ever you need, (my discord Demi 소금#9026)

One last thing is that Twisting and pre-tinning the wires is almost a must when soldering anything.

Soldering Tip(D24-Tip) : https://www.amazon.com/gp/product/B06XYR3VTJ/ref=ox_sc_saved_title_7?smid=A2FGAWCX62OR7U&psc=1

Soldering Iron: https://www.amazon.com/NovelLife-Mini-TS100-Soldering-Digital/dp/B07D35B75T/ref=sr_1_2_sspa?crid=1PGZOPAOX1MUO&keywords=ts100+soldering+iron&qid=1557599888&s=gateway&sprefix=ts100%2Caps%2C148&sr=8-2-spons&psc=1

I started with a cheap iron from Radioshack and gave up on soldering for years because I sucked at it.

Then I upgraded to this Weller station and suddenly I was soldering like a pro. Temperature adjustment is amazing.

I don't know about any of the super-cheap ones on Amazon, but there's definitely value in spending more to get a great iron.

1st, heat the component and feed the solder into it.

2nd, If you have a cheap low wattage solding iron, objects with alot of metal will be hard to solder as it wicks the heat away too fast and doesnt get hot enough.

3rd, strip the wire a bit shorter, too much exposure especially without heat shrink allows for shorts

4th for removing solder as per above, sometimes you can just heat up the solder and tap the object against the table and the hot blob will fall off, i recommend though to either have solder wick or a solder sucker.

5th, for solder, use 60/40 lead - tin flux core solder, thinner the easier it is to work with.


soldering can be done cheap and easy but nothing beats having the proper tools.

Practice, practice, practice.

Although i will say when i was younger i also had joints look like that too.


If you continue to do this alot, here are the tools i recommend

Solder Wick

Solder

Iron and Solder Sucker


although if you really do alot of solder, get a good temp controller one like this

Weller Soldering station

I highly recommend splurging a bit on your soldering station, saves a lot of heartache in the long run

Weller is pretty solid. This is what I have and I'd consider it to be a good entry-level model:

Weller WES51 Analog Soldering Station

Also, yeah you're going to want variable and analog

Have fun and be careful!

I know. That was the first thing I thought. I bought two kits for my x220 and x230, I screwed up royally the first attempt and wound up needing to use the second set of items.

Before you start, the equipment you will need:

• a precision screwdriver kit. This is what I use
  
• Exacto knife
  
• Dremel/pliers/sandpaper to make room for the LCD.
  
• canned air to clean up the plastic and metal shavings from dremel/pliers/sandpaper
  
• as /u/Bredius88 already mentioned, flux. I used liquid flux. If you use liquid flux you will also need rubbing alcohol and qtips to clean up.
  
• desolder pump
  
• magnifying lens of some sort. I used this which was good enough and could also keep my glasses on.
  
• kapton tape. (1/4" width or less)
  
• If it has been a decade since you last soldered or have shaky hands, or both in my case, I strongly suggest buying very thin solder and, if possible, a quality soldering iron like a Hakko FX888D. These were suggested by the EEVblog soldering tutorial made the second time around far easier.
  
  
  A few words of "wisdom"
  
  
• Take your time and do not rush. It is incredibly easy to miss things in the installation guide.
  
• DO NOT FORCE ANYTHING. If the LCD screen does not lay flush with the screw holes or the bezel is not clipping, you need to remove more material from the case/bezel
  
• Do not be stingy with the flux
  
• Do not over heat your soldering iron
  
• The sense wire looks like it is copper, but that is just the film on it. Gently scrape it with the exacto knife to reveal the wire in side. It will not solder with this film on it
  
• For each step, tape the piece in place before soldering then gently remove the tape. This was the only way I could solder the sense wire because it is so thin and light
  
• The eDP cable is very fragile. Do not keep plugging/unplugging it. If you do need ot unplug it (like after testing), only unplug the side from the board and keep pressure on the board when doing so as not to wreak your solder joints
  
• When everything has been soldered in place, test it before putting everything back together
  
  Also, on the V5, I used the old installation guide and the big difference is that the power is connected to the far left under the fuse marked "P". In the picture your finger is kind of covering it.
  
  EDIT: Anyone trying to justify spending ~$125US on a good soldering iron and solder just remember that replacing the motherboard will cost you about the same and will not be as useful a decade from now.

If you’re running a brushed motor you’d only have 2 leads so it would work. I personally prefer 4mm bullet plugs for the motor myself.

As far as for battery and esc leads I think they’re about the nicest plugs out there. They’re way nicer than deans if you get the version with the cover at the bottom. This way you don’t have to use shrink tubing to cover the soldering. Makes for a nice clean look

Also I find them much easier to solder. They have a C shape to them so you lay the wire in a little channel and can solder away.

Last, if soldering is a bad experience you should consider upgrading your soldering iron. I use a hakko and it makes soldering so easy it’s incredible. It puts heat at your joint quickly so you get on and off without heat traveling everywhere. No wire is too thick or difficult to get the solder to adhere to.

Couple this with a helping hands setup from amazon and soldering becomes a simple and dare I say fun task. Believe me I used to hate it every time.


Hakko FX888D-23BY Digital Soldering Station FX-888D FX-888 (blue & yellow) https://www.amazon.com/dp/B00ANZRT4M/ref=cm_sw_r_cp_api_i_M2ZMDb5GVCP21

I got mine for $70 so maybe check around. Or perhaps they’ve gone up :/


Fstop Labs Helping Hands Soldering Tool, Third Hand Soldering PCB Holder Tool, Four Arms Helping Hands Crafts Jewelry Hobby Workshop Helping Station Non-Slip Steel Weighted Base https://www.amazon.com/dp/B07TTZCZPR/ref=cm_sw_r_cp_api_i_z3ZMDbM7HTAT0

So helpful. Game changer.

Keep in mind that some of the people in this sub are professionals and they are only going to suggest pro gear. And while I agree with them that a really great iron is a great idea, you can get away with something cheaper than $100 and still get great results.

The iron you posted is probably crap considering how cheap it is. That same iron direct from China is like $5, so that will tell you something. If I can suggest something in between a Hakko and the toy, I've used this iron regularly for years: https://smile.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC

My ideas:

• 2 meter transceiver - Baofeng A great and cheap introduction into amateur radio. For those already a ham, I don't need to say anything more about the Baofeng.
  
  
• Baofeng 3800mAh Battery Double the capacity of the original battery. Makes it more unwieldy though.
  
  
• Weller Analog Soldering Station Imagine using an actually good soldering iron!
  
  
• Weller Industrial Soldering Gun If you like making antennas.
  
  
• APRSTM GPS position Encoder Broadcast your GPS coordinates through radio.
  
  
• Radio Astronomy Kit Listen to radio emissions from the Sun and Jupiter.
  
  
• Oscilloscope Kit See the a visual of RF? I haven't played with oscilloscopes.
  
  
• 20M CW Transceiver Kit Get 2 and practice morse code with a friend.
  
  
• Arduino Uno Starter Kit Arduino does more with electronics and Raspberry Pi more with Python programming.

I bought this Aoyue a couple weeks ago and its been pretty great. It uses the same style tips as the Hakko and came with a decently fine tipped one. I bought a thicker ended tip last week that is nice to use on heavier gauge wire but for motors and ESCs liked the fine tip better.

I've never done anything with RCs before and this was really my first experience soldering anything that mattered.

This was my first iron, though under a different branding. It's only $16, and it has a knob you can spin that at least loosely correlates w/ the iron's temperature.

I wouldn't recommend it, though. I splurged for a Hakko FX-888D a couple of months later and haven't regretted it once. It truly is a night-and-day difference. Working with my old iron was like pulling teeth. Working with the Hakko is effortless.

I'd definitely recommend an upgrade. If you're un(willing|able) to spend $100+ on a soldering iron, I'd recommend still getting the first one I linked, along with some Hakko tips. Hakko tips are about 10-20x as expensive as their no-name counterparts, and you absolutely get what you pay for.

Easily the most frustrating part of using my first iron was how quickly the tips would oxidize, even though I kept them tinned religiously. Hakko tips, when cared for, will last indefinitely. I wouldn't be surprised if nice tips + cheap (but temperature controlled) iron got you 70% of the performance of the all-Hakko kit.

The first one you pointed to provides a constant wattage setting, what you want is a constant temperature soldering station/iron, so that's not what you should look for. (its better to just get a "dumb" 25 watt iron instead at that point)

When I said Weller or Hakko I meant the robust WES51 or the FX888, but if those are outside of your price range, thats fine, the ubiquitous Hakko 936 has a ton of clones which are very cheap and some of them do actually have decent quality (see video discussing the topic, you might also want to google "936,"
936 clone," "936d," etc for more info).

I personally know some factory people due to my line of work and there seem to be 2 noteworthy brands of clone manufacturer, Aoyue and YiHua, Aoyue is the more premium brand and YiHua is the mass produced brand, apparently both are commonly used by factory workers and they are quite good because factory workers also need good equipment due to the nature of their trade.

I would look for a Aoyue 936 clone if I were you, just get this or this if you must use amazon, or search "aoyue" in fleabay.

A couple of things come to mind:

A) Cool.

B) Instead of drilling through your stencils, I recommend using a finishing nail or an awl and banging pilot divots. This centers and guides the drill bit, and keeps you from killing your stencil, just in case.

3) Try heat shrink tubing. It's not terribly expensive, it's fun to use, and it makes you look clever.

D) In the event that you ever want people to think that you are very clever, get a decent soldering iron. If you have a lot of extra money to throw around, get a fancy Weller station. If not, I recommend the adorable Hakko FX-888. Now that the analog version has been discontinued, it's hard to find on sale, but... they're fantastic. If you want to feel fancy, you could get something like this. Look at all those bits! I don't know either!

Haha, completely self taught through trial and error, thanks! Having the right kind of paste flux and magnification helps. I’ve also purchased one of these to help keep things steady with this and future jobs.

QuadHands Helping Hands Third Hand Soldering Tool and Vise
https://www.amazon.com/dp/B00GIKVP5K/ref=cm_sw_r_cp_api_Oh.MBb478C70E

This took me 5 minutes to put together.

Commercial Version:
hobby creek version

Materials List:

• coolant hoses
  
  
• alligator clips
  
  
• A solid piece of wood
  
• some heatshrink
  
• some hotglue...
  
  

1. The threaded connector on the hoses is a 1/2"-20 thread. So grab a spade bit or 1/2" bit and drill as many holes as you want into your base.
   
   
2. Don't make the mistake I made and either use a dense hardwood for the weight, or offset the mounting holes further back so it doesn't tip forward.
   
   
3. Insert the coolant hoses and hot glue from the bottom then around the base and let that set
   
   
4. drill the tube openings to the diameter of the alligator clip arm (about 1/4") but make sure it's snug, smaller is better than bigger.
   
   
5. shoot some glue into the tube opening as well as the alligator clip
   
   
6. slide on a tiny piece of heatshrink onto the tube
   
   
7. push the alligator clip into the tube then heat the heatshrink around the connection (I used marine heatshrink which has a built in heat activated adhesive to help this connection)
   
   
8. grab some rubber dots or no slip feet and stick them on the bottom of your base board.
   
   The amazon link I linked to sells the hoses in packs of 6 so you can make one for yourself and a friend, or do what hobby creek did and fix 4 arms to the base (which in my opinion is a little overkill).
   
   It's not 100% rigid, but for a $9 build, it's "rigid enough".

BONUS TABLE

All of the above is assuming you have everything required for building your quad if not below is a table with everything i think is necessary for building a quad. All these links will be from amazon

Part Type | Part Name | Quantity | Total Cost | Reason | Link
---------|---------|----------|----------|---------|----------|
Soldering Station | Hakko FX888D-23BY Digital Soldering Station | 1 | $100 | When it comes to working with quads and electronics you really don't want to skimp on the thing that's putting it together. A good soldering station can change your entire experience when it comes to building quads. For this reason we go with a Hakko once bought you will not need anything else later on. | http://www.amazon.com/Hakko-FX888D-23BY-Digital-Soldering-FX-888D/dp/B00ANZRT4M/ref=sr_1_7?ie=UTF8&qid=1458237822&sr=8-7&keywords=soldering+station
Hot Glue Gun | CCbetter® Mini Hot Glue Gun | 1 | $15 | You will use this more than you think, everything from securing your camera, antennas, etc to adding extra insulation to your components to ensure nothing falls off or gets ripped off. | http://www.amazon.com/CCbetter%C2%AE-Temperature-Melting-Flexible-Projects/dp/B01178RVI2/ref=sr_1_3?ie=UTF8&qid=1458237957&sr=8-3&keywords=hot+glue+gun
Velcro | VELCRO Brand - Sticky Back | 1 | $11 | Sometimes you need things to only stick for a bit then take it off. Velcro is pretty much self explanatory keep your vtx in place among other things | http://www.amazon.com/VELCRO-Brand-Sticky-Back-Black/dp/B00006RSWT/ref=sr_1_sc_1?ie=UTF8&qid=1458238198&sr=8-1-spell&keywords=stick+yvelcro
Zip Ties | Heavy Duty Black Cable Ties | 1 | $11 | The corner stone of fpv IMO. These are keeping more quads flying than anything else. | http://www.amazon.com/Heavy-Black-Cable-Ties-120lbs/dp/B003Y61A10/ref=pd_sim_60_4?ie=UTF8&dpID=41r7oTe3IpL&dpSrc=sims&preST=_AC_UL160_SR160,160_&refRID=1G5GJ28Z3M8JBJDW67RV
Solder | Miniatronics Corp 1064004 Rosin Core Solder 60/40 4oz | 1 | $12 | You are always going to need solder and this as the flux mixed in meaning it will be a very easy to use solder. | http://www.amazon.com/Miniatronics-Corp-1064004-Rosin-Solder/dp/B0006O933K/ref=sr_1_7?s=hi&rps=1&ie=UTF8&qid=1458238393&sr=1-7&keywords=solder&refinements=p_85:2470955011
Velcro Straps | Reusable Dubbex Black Velcro Cable Ties | 1 | $13 | Can be used for pretty much anything like batterystrap, hold wires down etc. | http://www.amazon.com/dp/B01AW0BDNK?psc=1
Voltmeter | Blackcell DC 3.2-30V LED 0.56inch Panel Meter Digital Voltmeter | 1 | $7 | Eventually something is going to go wrong and you are going to have to ensure that your voltages are correct. You are going to need this to verify volt outputs and to figure out what they are when there is no documentation for what you are looking at | http://www.amazon.com/Blackcell-3-2-30V-0-56inch-Voltmeter-Two-wire/dp/B00ZZIXT8W/ref=sr_1_6?s=electronics&rps=1&ie=UTF8&qid=1458238663&sr=1-6&keywords=voltmeter&refinements=p_85:2470955011
Desolder Tool | LyonsBlue Desoldering Vacuum Pump | 1 | $9 | Very useful for cleaning up to much solder or removing solder from contact pads to redo. Simply heat up the solder and suck it out. | http://www.amazon.com/LyonsBlue-Desoldering-Vacuum-Solder-Removal/dp/B003FHYL7I/ref=sr_1_2?ie=UTF8&qid=1458238959&sr=8-2&keywords=desolder
TOTAL | FOR | ALL | $178 | |

this soldering iron is amazing. I bought one, and on my recommendation, 3 friends have bought one too. They have all thanked me for the recommendation.

It has good temperature control, good tip cleaning ability, and the highly flexible cord connecting the iron to the controller makes soldering so easy. My previous cheap soldering iron had a stiff, heavy cable that "pulled" on the top of the iron, making delicate, accurate soldering work really frustrating and difficult.

It's always worth buying the best tool you can afford unless it's single use. I have a decent weller that I've since replaced with a very decent Hakko.

This is a very nice iron that will serve you well: https://www.adafruit.com/products/1204

This is my older iron, served me well, the only reason I switched to the hakko is because I bought one for work and ended up liking it: http://www.amazon.com/Weller-WES51-Analog-Soldering-Station/dp/B000BRC2XU/ref=sr_1_1?ie=UTF8&qid=1462577050&sr=8-1&keywords=weller

Honestly, I'd get a cheap solid chinese one off amazon, with a proper stand. The SEEED has a bit of an issue staying up to temp.

I've had one of these for a few years, and it's been pretty decent. Half the price, more options, and a much better stand.

A portable iron has more problems than it solves, usually. A nice station is almost always better.

I recently did my first build and used the Xtronic solder station. It worked flawlessly. Was very tempnatable, comfortable to use, and hits a great value price point.

X-Tronic Model #3020-XTS Digital Display Soldering Iron Station - 10 Minute Sleep Function, Auto Cool Down, C/F Switch, Ergonomic Soldering Iron, Solder Holder, Brass Tip Cleaner with Cleaning Flux https://www.amazon.com/dp/B01DGZFSNE/ref=cm_sw_r_cp_apa_i_x232Db22N3N86

I would recommend this one (Aoyue 936, $45). I have it and am really happy with it. Heats up nice and quick, and adjustable, it's all steel and durable plastic, looks and feels nice. And you can buy 10 tips for like 5 bucks if you want.

Thanks! Soldering isn't too hard (I also was afraid of soldering). It's intimidating at first, but after a couple hours of doing it, you'll get more comfortable with it. Getting a cheap mech to practice soldering/desoldering on would probably help you get acquainted with the whole process. This is the soldering iron I used, and this is what I used to desolder. I also used this to clean the tip of the soldering iron in order to make it perform more consistently.

Heated PCBs are hard anyway because they are a weird combination of heatsinking and thermally insulative. If you are ever going to solder a second thing, just get a good Hakko or something. I have the analog version of the linked iron, and love it. I leave it at 350C constantly ... it gets to temp in like 20 seconds and holds it rock solid.

http://www.amazon.com/Hakko-Digital-FX888D-CHP170-bundle/dp/B00AWUFVY8/ref=sr_1_1?ie=UTF8&qid=1421772043&sr=8-1&pebp=1421772044939&peasin=B00AWUFVY8

Also:
http://www.amazon.com/SRA-Soldering-Flux-Low-Solids-No-Clean/dp/B008OC0E5M/ref=sr_1_1?ie=UTF8&qid=1421772121&sr=8-1&pebp=1421772121985&peasin=B008OC0E5M

I'd highly suggest you plunk down and get both. You'll feel like a wizard from now on with soldering. For the flux pen, just drown your connections, wire, pads, etc in flux before soldering. Within a very generous reason, you cannot overflux things, and it makes the solder actually behave like it should. It globs where it's supposed to, doesn't make those stupid little peaky points that bridge everywhere, and so on.

Soldering is one of those tasks where it really pays off to invest a little bit more in your tools at the beginning. /u/1-11 mentioned the Weller WLC100 - I second this recommendation. I've had one for almost 8 years and it's never let me down, though I bought a nicer iron a few years ago (Aoyue 968A+) and the Weller hasn't seen much use since.

The kit you posted is probably not very high quality. I would steer away from it and spend the extra money to get something you know will perform well for years. You do want some of the things from that kit, though:

• Solder sucker
  
  
• Solder wick
  
  
• Tweezers
  
  
• Various tips
  
  
• Flux (I use a flux pen similar to this one for most things as it's a little easier to apply)
  
  A good way to practice is to get some perf board (the tan-colored breadboard-looking PCB prototyping boards), a pack of random wires and/or resistors/capacitors, and just start soldering things in. SparkFun sells some good kits for beginner soldering, and they have a few good tutorials as well.
  
  Always use flux, always tin your wires before soldering them to anything, and always hold the iron on the solder long enough for it to completely flow. Learn how to use solder wick and you'll be able to repair just about anything. Finally, always tin your tips before storing the iron - don't want the tips to corrode!

I have an older Weller that I got used, this model: https://www.amazon.com/Weller-WES51-Analog-Soldering-Station/dp/B000BRC2XU/ref=sr_1_5?s=hi&ie=UTF8&qid=1520878668&sr=1-5&keywords=weller+soldering+iron
It's a little pricey for what it is buying new, but it's really quality. I've soldered many thousands of components large and small with it. Looks like Weller has some newer models that are about the same price and probably more feature-full/powerful.

I can recommend getting a brass sponge instead of the ones you wet, it's cleaner and less hassle. I also use a solder-sucker and solder-wick-braid regularly. I also use a pair of "helping hands" with a magnifying glass, a DIY fume-extractor (PC fan with some activated charcoal filter behind it), and a small vise for holding circuit boards and such. That's just about the entirety of the things I use for general electronics mucking-with.

Sorry for the late reply. First of all, take all of this with a grain of salt. This is my first build, so I am by no means an expert. You should definitely look in to all this on your own rather than blindly trust my purchases.
Here are the tools I got in my Amazon order:

• Wire Stripper
  
• No Clean Flux Paste
  
• XT60 Connectors
  
• 60/40 Rosin Core Solder
  
• Loctite Threadlocker 242 (blue)
  
• Weller 40 Watt soldering station
  
• Solder tip cleaner
  
• Helping hand with LED
  
• Bullet connectors
  
• Liquid electrical tape
  
• Heatshrink variety pack
  
• Chisel tip for soldering iron
  
• Servo cables
  
• 12/14/16 AWG silicone wire
  
• Zip ties
  
  I hope this helps.
  
  

Sure do! I was looking at the Massdrop listing for the KC60 and then found this kit for it on aliexpress. Thought it'd be a great learning experience to build my own. I've got a pretty extensive list of possible soldering irons on Amazon like Weller WLC100, Soaiy 60 watt, and a couple more from Vastar and Weller. I'm completely new to this so I'm not trying to spend a fortune on the iron

Not a bad idea - you're much less likely to electrocute yourself!

I can't stress enough the importance of good solder joints! Don't glob solder onto the iron and then apply to the piece of work. It's important to thoroughly heat the work until IT melts the solder and the solder is allowed to naturally flow into the nooks and crannies of the work.

Also, you are embarking on a way of life. This is a serious commitment of time and money. Do yourself a favor and buy a GOOD soldering station - not a cheap soldering pen!!!

First.. what soldering iron are you using? Looks like it's not getting hot enough and the solder isn't getting up to temperature.

If you plan on soldering more maybe invest in something like this.. I've been using one for years and it's a wonderful soldering station. The cheapo walmart irons are usually not good at all.. even now being much better at soldering I still can't use one of those.

https://www.amazon.com/Hakko-FX888D-23BY-Digital-Soldering-FX-888D/dp/B00ANZRT4M/ref=sr_1_1?ie=UTF8&qid=1492479856&sr=8-1&keywords=hakko+fx-888

This is also a good starter setup.

https://www.amazon.com/Weller-WLC100-40-Watt-Soldering-Station/dp/B000AS28UC/ref=sr_1_1?ie=UTF8&qid=1492479939&sr=8-1&keywords=weller+soldering+iron

The Hakko FX-888D runs $100 on Amazon.

I bought this one for $30 and found temp settings in the reviews. Setting marker 3.25-3.75 gets you right around 350°C, coincidentally.

I also bought that cheap-ass Valstar solder sucker with free wick. From what I read about the wick, it needs flux to get the solder flowing into it. The solder sucker sucked. I ended up taking a Dremel deburring bit to create a divot in the metal housing to capture the little arms so it wouldn't spring apart when I hit the plunger release. After that, it worked pretty well, though I usually got a pretty good seal right over the solder and switch leg - no desoldering controllers. I did have one switch leg that was bent over the contact, which required some physical assistance to move while the solder was melted before I could clear it.

Desoldering wick looks like it works great and would work for your situation, if you use it right.