Reddit mentions: The best tile cutters

I used this for a long time, dust free, but not the most perfect cuts

Makita JS8000 Variable Speed Fiber Cement Shear Kit https://www.amazon.com/dp/B000N5URAU/ref=cm_sw_r_cp_api_i_e8pQCbHSAW4V4


Then I switched to this, and it’s amazing, fast clean accurate and easy



Bullet Tools 13 in. EZ Shear Siding Cutter with blade for hardie plank, vinyl siding, fiber-cement siding, and trim https://www.amazon.com/dp/B008EX4RNQ/ref=cm_sw_r_cp_api_i_Z7pQCbKR0N631

After redoing my 550 sq ft bedroom in laminate, I would HIGHLY recommend a cutter like this Exchange-a-Blade 2100005 9-Inch Laminate Flooring Cutter https://www.amazon.com/dp/B00B0BYY4Q/ref=cm_sw_r_cp_apa_3vPAzb9EFZFGA from Amazon. Practically zero clean up. I used a saw at the start and then half way through I thought to myself, "there has to be a more efficient way". Once I got this, it was a breeze to work through and finish.

Vinyl flooring seam sealer is not meant to be used on vinyl composite tile. Neither is grout.

Pro floor covering installer here. What we would do is pull that tile and replace it with another one. You take a picture of the tile, or go back to the store in the area the tile was bought to lookup the invoice information, and get a matching tile to replace it. If that is not an option, applying low heat (say from a heat gun/hair dryer) to the surface of the tile will make it more pliable and easier to peel up.

If you can get it peeled up, and the glue is still sticky/tacky, you can simply place it back in the hole with the gap next to the wall. You can then cut a sliver off another tile using a tile cutter which are rentable at most home improvement stores, and fill the gap with that. It will be less noticeable and less likely to pop back out against the wall.

If you get the tile up but the glue is bad, you will need to apply tile adhesive and let it dry then stick the tile back in the hole.

Vinyl seam sealer is meant for sheet goods. It is liquid vinyl that is [supposed to be/usually] clear gloss or clear matte. It is like a more watery form of caulk.

There is more industrial plastic vinyl which is heat bonded to stuff like Medintech that is used in heavily cleaned environements [like hospitals] which you might come across too. It also is not meant for vinyl composite tile.

https://www.amazon.com/gp/product/B01LX7PZ5Q/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1 is the tool I used to cut the glass. Get yourself a diamond file and some fine grit sand paper to chamfer the ends. It doesn't take much to chamfer them. You just need to make sure the glass will not cut the internal o-ring in the fittings. I used a tape measure for the runs. Add an extra 8mm for seating depth on Bitspower fittings. For example, if you want to run a length of glass between two fittings and the length between the two fittings end to end is 50 mm, you will cut a length of glass that measures 66 mm to account for seating depth. I hope this helps.

https://www.amazon.com/QEP-10214Q-Ceramic-Cutter-Cutting/dp/B00AM1Y15M/ref=mp_s_a_1_4?keywords=tile+cutter&qid=1563577416&s=gateway&sprefix=tile+cutt&sr=8-4

Tile cutters score the surface and the tile can then be snapped apart. They work well for ceramic tile, not so well for natural stone.

I have used the following tools for all my tiling needs so far each has their own strengths and weaknesses:

• The quickest, but can't do special cuts like L,cutouts or diag.
  https://www.amazon.com/Kobalt-24-in-Snap-Cutter/dp/B0764KK8RQ
  
  
• I use this the most for any kind of special cut that I couldn't get with snapping. You also need to purchase a diamond blade for it. (Dry cut )
  https://www.amazon.com/DEWALT-DWE402-2-Inch-11-Amp-Grinder/dp/B00RVZ7DNO
  
  
• I recently had to purchase this to cut natural stone (marble), it worked surprisingly well for the price but was messy and had to be used outside.
  https://www.amazon.com/DEWALT-DWC860W-4-3-8-Inch-Masonry/dp/B003BVW5NU

Tile cutting bit: https://www.amazon.com/Dremel-562-Tile-Cutting-Bit/dp/B00004UDIC

Diamond cutting wheel:https://www.amazon.com/Dremel-545D-545-Diamond-Wheel/dp/B00004UDI9/ref=pd_sim_469_3?_encoding=UTF8&pd_rd_i=B00004UDI9&pd_rd_r=269YAJP4K67TJ18GNAYD&pd_rd_w=t28id&pd_rd_wg=i2XAg&psc=1&refRID=269YAJP4K67TJ18GNAYD

Even carbide burr bits will work (slowly).

Wetting the area will keep down the dust and extend the life of your tools, but isn't strictly necessary.

That thing in the picture is a tile cutter. http://www.amazon.com/QEP-10267-12-Inch-Tile-Cutter/dp/B000FK5J5Q/ref=sr_1_7?s=power-hand-tools&ie=UTF8&qid=1309721973&sr=1-7

Or you can buy a vet cutter.
Roberts 10-895 Vinyl Tile Cutter Silver https://www.amazon.com/dp/B00FK8V0RY/ref=cm_sw_r_cp_apa_i_0cx1Cb87NM1CZ

It is a glass cutter

https://www.amazon.com/IMT-Tungsten-Professional-Replaceable-Reservoir/dp/B06XYTBPPD

Rectangles are the easiest shape to cut. You'll need a glass cutter and some experience. If the glass is tempered, it will shatter. Or take it to a local glass shop and they will cut it for you.

very easily it could damage the tile. You could get one of these or if you want you could us a multi tool with one of these

Those are Dremel Tile Cutting bits.(#562)
Dremel 562 Tile Cutting Bit https://www.amazon.ca/dp/B00004UDIC/ref=cm_sw_r_cp_apa_i_uOCGDb664C5FF

then they used an electric tool called a cutting disc..... https://www.amazon.com/Evolution-DISCCUT1-12-Inch-Cutter-Orange/dp/B003K4FQ6G/ref=sr_1_4?keywords=electric+cutting+disc&qid=1567192980&s=gateway&sr=8-4 weaker krytonites would take less time to cut through, they have levels to them