Reddit mentions of RioRand XT60 Drone Connectors (5 Pair)

I already had the volt meters and XT60 plugs lying around, so I just had to buy a cord and stick everything together with solder, heat shrink, and hot glue. Happily enough, my B6AC's DC input uses the same plug, so I can use this to charge 1S batteries when I'm out and about, too. (Not much point in charging 4S this way unless I have something like a 5Ah pack on me, but I guess it's a possibility.)

Hello, I was just about to order a couple days ago, then figured I should ask you all here on /r/Multicopter if you have any recommendations for changes. I can solder and have tools, is there anything that I am missing here for a complete setup? Oh I also already own a Spektrum DX6i with two Spektrum AR610 receivers.

item | link | price
-|-|-
AV transmitter/receiver | Boscam 32Ch 5.8G 600mw 5km Wireless AV Transmitter TS832 Receiver RC832 for FPV | $35.63
Charger | Genuine SKYRC iMAX B6 Mini Dual Power 6Amps 60Watts Profess​ional RC Balancing Battery Charger & Disc​harger (Version RCLITE) w/ Micro USB Port For RC Lipo Battery Cherge, Temperature Port | $36.58
Heat shrink | uxcell® 1 Meter 50mm Dia Ratio 2:1 Heat Shrinkable Shrinking Tube Black | $6.66
Flight Controller | AbuseMark Acro Naze32 Rev 6 Flight Controller W/ Straight / Bent Pin Headers, Breakout Cable, & Apex RC Products Nylon Standoffs | $39.99
Frame | YKS DIY Full Carbon Fiber Mini C250 Quadcopter Frame Kit for FPV Mini Quadcopter Part | $37.99
Motors | 4pcs EMAX RS2205 2300KV Brushless Motor 2CW 2CCW for QAV250 QAV300 FPV Racing Quadcopter | $78.79
ESC's | Crazepony 4pcs Littlebee 20A Mini ESC Oneshot125 Electronic Speed Controller 2-4S Brushless for FPV Multicopter Quadcopter | $39.99
Props | Hooshion® 16 pcs 8 pairs GemFan HD HQ 5030 5x3 CW CCW Propeller for Mini QAV250 Quadcopter (Black+Orange) | $12.59
Connectors | XT60 Drone Connectors 5 Pairs (5 Male and 5 Female) | $2.96
Battery | Turnigy 2200mAh 3S 20C Lipo Pack | $16.70
AV Antenna | Anbee® FPV 5.8Ghz Circular Polarized Clover Leaf Antenna High Gain Aerial Set w/RP-SMA Plug | $10.98
Camera | SC2000 600TVL D-WDR DNR Board Camera SONY Super HAD CCD for FPV, 2.8mm Lens, IR Blocked Filter | $33.99
| total | $352.85

Sorry for the late reply. First of all, take all of this with a grain of salt. This is my first build, so I am by no means an expert. You should definitely look in to all this on your own rather than blindly trust my purchases.
Here are the tools I got in my Amazon order:

• Wire Stripper
  
• No Clean Flux Paste
  
• XT60 Connectors
  
• 60/40 Rosin Core Solder
  
• Loctite Threadlocker 242 (blue)
  
• Weller 40 Watt soldering station
  
• Solder tip cleaner
  
• Helping hand with LED
  
• Bullet connectors
  
• Liquid electrical tape
  
• Heatshrink variety pack
  
• Chisel tip for soldering iron
  
• Servo cables
  
• 12/14/16 AWG silicone wire
  
• Zip ties
  
  I hope this helps.
  
  

I used the following to connect a power supply to the one I own, and it works great.

http://www.amazon.com/HDVD-trade-10pack-Pigtail-Female/dp/B00CUKHN0S?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o04_s00

http://www.amazon.com/Shipped-Cheap-Drones-Connectors-Female/dp/B00G197NHW?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s00

http://www.hobbyking.com/hobbyking/store/__36904__HobbyKing_105W_15V_7A_Switching_DC_Power_Supply_US_Warehouse_.html