Best products from r/Bittboy

We found 20 comments on r/Bittboy discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 12 products and ranked them based on the amount of positive reactions they received. Here are the top 20.

12. UTEBIT Professional SD Card Case Waterproof 24 Slots Shockproof Memory Card Holder Box Wallet with Lanyard for 12 SD Cards + 12 Micro SD Cards (TF Cards) Rustproof Compact Flash Card Organizer Storage

    Features:
  • 【Bigger Capacity】Size: about 15.7cm (Length) x 8.4cm (Width) x 2.8cm (Height). It can stores 12 pieces SD card + 12 pieces micro SD card (TF card), portable, easy to carry. PLEASE ATTENTION: This product set not included SD card/ TF card, you need to buy it separately.
  • 【 Waterproof】SD box seal was made by sofy silicone, waterproof/dust-proof/sand prevention, protect SD/micro SD card effectivly. ※ Waterproof Test: the SD card case was completely soaked in water for 5 minutes, and there was no sign of water entering inside the SD card case.
  • 【Material】Environmentally friendly ABS plastic case, rust-proof, corrosion resistant, no odor. Exquisite concave case design, comfortable hand-feel and anti-slip.
  • 【 Good Protection for SD Card】Internal card slot was made by EVA sponge, durable and no fading, antimagnetic, shockproof, moisture proof, protect SD card well and prevent it from scratching. Each slot is carefully crafted according to the size of the corresponding card to ensure safe storage of the SD/microSD card.
  • 【Special Design】Safety lock and lanyard design, rigorous switch buckle design, can be fastened to the box door, easy to open and close. External with lanyard design, easy to carry.
UTEBIT Professional SD Card Case Waterproof 24 Slots Shockproof Memory Card Holder Box Wallet with Lanyard for 12 SD Cards + 12 Micro SD Cards (TF Cards) Rustproof Compact Flash Card Organizer Storage
▼ Read Reddit mentions

Top comments mentioning products on r/Bittboy:

u/pikafoop · 1 pointr/Bittboy

Here's a few pictures of the battery.

  1. Its dimensions are about 59.5 x 36.5 x 3.75mm
  2. It seems to be 3.7V and 970mah
  3. The distance between the connectors on the pin is 1mm
  4. We'd want to greatly exceed 970mah (see 2), but my rough measurements indicate very little clearance between the existing battery and the back panel

    For instance, a quick search shows this candidate 1800mAh battery, but it's almost 3mm thicker than the existing battery (and would need a new connector). That's probably enough extra bulk that we would need to 3D print a new back cover or find a different attachment solution.

    If you find a better alternative, I'd be interested!
u/defaultluser · 7 pointsr/Bittboy

Yeah, it's very portable. I just put mine inside a slide-in glasses soft case, and it's survives wherever I've taken it.

It gets a spot in my kilt pocket right next to my phone (inside a case)! These are a perfect fit:

https://www.amazon.com/gp/product/B07PRZ29N9/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

u/gangstanthony · 5 pointsr/Bittboy

i was able to use 128gb u3 with the standard tutorial

https://github.com/TriForceX/NewBittboyCFW/blob/master/PocketGo-Guide-EN.md

i think this was the card

https://www.amazon.com/Samsung-MicroSDXC-Adapter-MB-ME128GA-AM/dp/B06XWZWYVP

and i recommend u3 because of how much quicker it is to flash firmware from scratch as well as copying large files

i don't have a larger card, so I'm not sure of the max supported size

u/the_blck_adder · 2 pointsr/Bittboy

Ended up ordering these https://www.amazon.com/gp/aw/d/B07CVC7CZF/ref=ya_aw_od_pi?ie=UTF8&psc=1

And a standard soldering kit with wires at the ready.

And a shoulder button hole guide for another device to have it at the ready.

(https://www.thingiverse.com/thing:2466985)

u/Oleaster · 1 pointr/Bittboy

I tried using etcher to flash this to a fresh 16gb sd card and was getting the error "source and destination checksums do not match" after the process completed. It created four partitions on the card and two seem unaccessible. Am I doing something wrong? I'm new to this and I haven't received my PocketGo yet, but I'm trying to get my card prepared.

u/MDS0LDI3R · 1 pointr/Bittboy

I had an extra one of these lying around when I got my BittBoy awhile back and it works well: https://www.amazon.com/Co2Crea-Shockproof-Carrying-Essential-Elements/dp/B00IHUWW06