(Part 2) Best products from r/HTC10

Can do!
This is the mount. It sits nicely in an airvent.


The mount came with a metal plate for the phone case, however I ordered a couple of replacement plates too.


Hope this helps! :)

I used magnetic mounts on old phones with a case but for my HTC 10 I didn't want to use a case so I got this mount which works great
https://www.amazon.com/gp/aw/d/B01DLGT5GY/ref=yo_ii_img?ie=UTF8&psc=1

This is my case, $11.
Nice and grippy.

Spigen Thin Fit HTC 10 Case with Premium Matte Finish Coating for HTC 10 2016 - Gunmetal https://www.amazon.com/dp/B01DAN14SA/ref=cm_sw_r_cp_apa_9wNhyb8M2BVYD

I have the cables from Amazon. They rapid charge.

None referral link.

USB Type C Cable, CHOETECH 6Pack [1.6ft1+3.3ft4+6.6ft1] Durable USB C to USB A (Type C to Type A) Cable for OnePlus 3, LG G5, HTC 10, new MacBook and More https://www.amazon.com/dp/B01H3COF76/ref=cm_sw_r_cp_apa_TtNhybRV02S42

This and this are both amazing cards. I use the 64GB Sandisk, myself.

I got these reusable ice cubes and i hold one on the back of the phone while I play games. Been doing it for months, haven't had any issue with condensation on the inside or anything. Lasts about 20 minutes or so until I need a fresh one.

Here's one I got that supports fast charging as well

I see; the large center section gives it rigidity for first placement. But yes, you're right I've already got the screen attached internally so I will have to remove it.

I ended up purchasing one from a local phone repair shop as Witrigs was 5-10 days shipping at best (... and for $25 in shipping charges). Buying locally only cost me $5, (score!). If I mess it up I'll go get another one.

I think I'll try this tomorrow.

EDIT: I did this. I ended up cutting a line up the side of the adhesive and I DIDN'T remove the center as there didn't appear to be a good way to do so. Mine came with an antennae (or wifi?) cutout for the center of the screen. I think all of the adhesive is actually important to stabilize the screen (or it was, in my case).

I still noticed after putting it all meticulously back together that the side stuck up a little bit. I purchased a new Spigen HTC 10 Case from amazon and the lip of the case extends past where the screen meets the frame. Otherwise I'd feel uncomfortable about it peeling and subsequently cracking the screen again. I also purchased a screen protector (tempered glass from Amazon, I believe) and put that on. My only complaint is that there's a couple mm around the edges that's unprotected from the screen and the case.

https://www.amazon.com/iOrange-Braided-Reversible-Connector-ChromeBook/dp/B010VFFSL4?th=1&psc=1


Benson approved and really high quality. I don't think anything can withstand cat teeth, braided or not. Don't leave your cables out.

It is going to heat up a bit while charging with any version of QC. QC raises the voltage with the amperage to let your phone charge faster. Whether it uses 5, 9, or 12 volts is determined by your phone's specs and what the charger can output.

It doesn't get too hot to pick it up. It gets noticeably warm with internal temperatures reaching around 32-35C or so. Idle temperature, for comparison, is around 28C. When you pick it up, it will feel kind of warm, but not hot. Your phone can take much higher temperatures than what it experiences during charging, so you're not causing any damage.

I have personally used all of the following Benson approved USB type-C items.

• Suaoki 3.3ft Micro USB Type C Nylon Braided Phone Charging Cable with Aluminum Connector 2.4A Max Current USB 3.1 Type C to USB Type A
  
• Anker PowerLine USB-C to USB-C 2.0 Cable (6ft) for USB Type-C Devices
  
• USB C Quick Charge 3.0 AUKEY Car Charger with Dual AiPower Ports
  
• USB C Quick Charge 3.0 AUKEY Amp Type-C Dual-Port Wall Charger; Includes USB-C Cable
  
• [2 in 1 Pack] Anker USB-C to Micro USB Adapter, Converts USB Type-C input to Micro USB, Uses 56K Resistor
  
• Type C, USB C to USB A iOrange-E 10ft (3M) Braided Cable
  
  Don't buy cheap-o USB type-C things right now. The cheap stuff may be using incorrect resistors and possibly damage your devices.

I've got this one.

Works really well. I've got apps and 4K video on it.

I have the older version of this and it works great. Charges quite quickly, but not as fast as the one that came with the phone. https://www.amazon.com/dp/B01LCDJ7LG/ref=cm_sw_r_cp_apa_sd4-ybBYAN333

I bought it from Amazon, this one

I haven't had any issues like that with my device that I've had since launch.

These are the cables I'm using, I have 4 & the stock cable which came with the device.
https://www.amazon.com/dp/B010VFFSL4/ref=cm_sw_r_wa_awd_x_2Hx2xbYB5E58M

The only issue was the base of the cable was a little too wide to fit while my phone was in the case. So I had to dremel the edges a bit to make them fit, but I've had no other issues.

Found this deal awhile ago. 6 cables for the price of one. Can't beat it

AUKEY USB-C to USB 3.0 Cable Braided Nylon (5-Pack 3.3ft x 3, 6.6ft x 1, 1ft x 1) for Samsung Galaxy S8, Nexus 6P 5X, Google Pixel, LG G5 V20, HTC 10 and More https://www.amazon.com/dp/B01B634WNK/ref=cm_sw_r_cp_apa_AG6-ybFMHG3T4

https://www.amazon.com/dp/B01DEJ7KE2/ref=cm_sw_r_cp_apa_97.6xb6V0DSEM

https://www.amazon.com/dp/B01HI5YYN8/ref=cm_sw_r_cp_apa_38.6xbVVR93D9

fix

I ordered this this morning with a coupon that made it $2.99 (expired, sorry :( )