(Part 2) Best products from r/moped

We found 22 comments on r/moped discussing the most recommended products. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 66 products and ranked them based on the amount of positive reactions they received. Here are the products ranked 21-40. You can also go back to the previous section.

Top comments mentioning products on r/moped:

u/andyleclair · 1 pointr/moped

Oh, that's great! Thanks a lot! I was reading this, but that's just engine.

u/the_mad_whistler · 2 pointsr/moped

It is indeed a powder, you mix it with warm water. Higher concentration should yield better result given the incredibly small space. This should do you for a long time: Hoosier Hill Farm Alum Granulated Pickle Powder, 1 Pound https://www.amazon.com/dp/B00UVAG21A/ref=cm_sw_r_cp_apa_i_gawSCbVRZVNQW

u/ChinatownKicks · 1 pointr/moped

Yeah Trail Tech is solid and can give you the important gauges. Wire it into your lights and you don’t even need a battery.

For the lights, get the 12v coil from Treats and replace your incandescent bulbs with these, which plug right into your fixtures:

https://www.amazon.com/gp/aw/d/B071V2DBWP?psc=1&ref=ppx_pop_mob_b_asin_title

u/PM_ME_UR_FAV_RECIPE · 5 pointsr/moped

I really like this fuel line from Amazon. I prefer a more transparent line to be able to see the fuel/

https://www.amazon.com/gp/product/B002ZTGLFC/

u/DrGeorgeTompson · 1 pointr/moped

yeah i didn't know how to do shit when i got into mopeds. You gotta learn fam.

5,000 miles is a really long time.

Unless you are racing your bike and need 10000% consistant ass blaster performance all the time, premixing is not as delicate or required as you think it is. just dump oil in at the pump; if it's close it's good enough. get a little doodad that's metered that you can carry oil around in if you are worried.


Think of wires as tubes and the electricity as fluid.

Ignition systems are fairly simple when it comes to the wiring. Well i guess the Urban express is a hair more complicated since it's a CDi but it's still pretty simple. more straightforward than the lighting.

Find a wiring diagram.

Hell, here's a video about circumventing the majority of the ignition electrical system.




Either way, i think you are underestimating the difficulty/cost(if you can't weld and shit) of swapping the subframe with a GY6. but you do you

u/wheresdangerdave · 1 pointr/moped

get an inline fuel filter. most fuel lines are 5mm(3/16"?).

De-rusting a step-thru is a pain in the but. You can buy some toxic acid crap that will do it, but you have to be careful you don't get it on yourself. I let apple cider vinegar sit in it for a week, drain, strain and refill it every other day or so. Then I'll do a day or so of Evapo-rust

Seems to be on sale at the momend on Amazon with free shipping w/ prime. Harbor freight also carries it and with the 20% off coupon that is always available it can be had for about $23ish and it is reusable!

u/eobanb · 2 pointsr/moped

A heavy chain, probably. A regular Master Lock, no way. It's trivial to cut a padlock using boltcutters. We're talking 10 seconds or less.

Many riders I know swear by Kryptonite's New York series. Here's one that should pretty well for locking to a bike rack, parking meter, etc.

u/jfourkicks · 2 pointsr/moped

Went with this, and real satisfied with its sensitivity/noise level.

https://www.amazon.com/dp/B07MFBV7TW/ref=cm_sw_r_cp_api_i_qCriDb5BDVTFR

u/Chojiki · 3 pointsr/moped

TORC T1 in Copper Pinstripe. It's got a nice smooth retro look to it without looking like a Power Ranger helmet. It's a full face and made of fiberglass tri-composite. The opening around the eyes is comparable to the Bell Bullitt. (The lack of this is what I really disliked on the Biltwell Gringo, my second choice.) And I got it for around $130 with some smart coupon usage (It's normally $199, much easier on the wallet than the $299 Bell Bullitt).

u/Young_Maker · 1 pointr/moped

http://www.amazon.com/NGK-B6HS-Spark-Plug-Pack/dp/B0000BXHSP

The type is NGK B6HS. Taken straight from the moped army page. I betcha the'll have an equivalent at the auto parts store if you don't want to order from amazon.

u/tman67234 · 1 pointr/moped

POR 15 sells a kit that comes with different cleaners and a sealant. It's the longest lasting solution I have used. http://www.amazon.com/POR-15-Cycle-Tank-Repair-Kit/dp/B000H9K4JQ

u/eldetepro · 1 pointr/moped

wonder if this would work. if the nub at the end of the non angled side can slide through the old part I have then I don't need the screw top. https://www.amazon.com/NIBBI-Motorcycle-Adjustable-Replacement-Carburetor/dp/B06W9MH2VT