#455 in Industrial & Scientific
Use arrows to jump to the previous/next product
Reddit mentions of Creality CR-10S 3D Printer HICTOP Filament Monitor Dual Z axis Screw Rods 300x300x400mm
Sentiment score: 3
Reddit mentions: 5
We found 5 Reddit mentions of Creality CR-10S 3D Printer HICTOP Filament Monitor Dual Z axis Screw Rods 300x300x400mm. Here are the top ones.
or
- UPGRADE: CR-10S updated with dual Z axies leading screw rod which make printing quality better and more stable, with different mainboard and firmware from CR-10.
- RESUME PRINTS: CR-10S has the ability to resume prints even after a power outage or lapse occurs.
- FILAMENT MONITOR: CR-10S mainboard with filament alarming function, this function can detective if filament is running out or not.
- WITH TWO COLORS (BLUE AND ORANGE) decorative strips inside. You can use either of them as per your preference.
- EASY ASSEMBLY: Delivery with three sets, just need about 10 minutes to assemble well.
Features:
Specs:
| Color | Orange,Blue |
| Height | 21.259842498 Inches |
| Length | 25.590551155 Inches |
| Number of items | 1 |
| Size | M |
| Weight | 22.7 Pounds |
| Width | 11.417322823 Inches |
FYI the CR-10s on lightning sale. Not many left.
Edit: sold out.
Now that I have a CR-10s what do? Any mods I should make my first priority? I seen the print bed heating takes time. Is that boostable with better power supply or separate power ?
I would recommend contacting amazon through amazon chat and asking for a replacement as the item is defective. They will likely have you order another and send the first back. I got mine on amazon though mine it is a hictop version. Here is the link https://www.amazon.com/gp/product/B074QLQSQV/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
Also I would recommend this as well as the microsd card slot on the control box isnt the greatest and is going to be alot more expensive(time or money or both) to replace than this 8 dollar cable. https://www.amazon.com/gp/product/B01D9JIUU0/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1 You will need a microsd to sd card adapter for it though. I just find handling a sd card much easier than using the micro sd.
It's a Creality printer, its just being sold through a company called HICTOP. I'm sure it's fine no matter where you get it from, but mine worked really well right out of the box. https://www.amazon.com/HICTOP-Creality-Printer-Filament-300x300x400mm/dp/B074QLQSQV/ref=sr_1_2_sspa?ie=UTF8&qid=1542812784&sr=8-2-spons&keywords=creality+cr-10s+hictop&psc=1
​
I do recommend looking into upgrading the firmware to Marlin 1.1.9 sometime down the road though so you can ensure you have thermal runaway protection enabled. It can be a little tricky at times, but this community is incredibly helpful as is r/3Dprinting and r/FixMyPrint. Good luck with the new printer! I love my CR-10S and post prints from it on Reddit from time to time.
OK - the 1st one lists itself as a CR-10 S5, which has a 500x600x500 build area. What is listed is the base CR-10 with a 300x300x400 build area. It's also NOT the "S" version which has lots of upgrades: mainly a filament sensor, a second motor for the z axis and has a Atmega 2560 instead of Atmega 1280 for the controller board.
The 2nd one lists itself as a base CR-10 and by all appearances seems to be one.
Seeing how a CR-10 sells for $499 on Amazon, this seems to be a good deal. You'd have to look at the eBay vendor's feedback to see if they are delivering what they advertise. It seems like the $400 price isn't out of the range of what they cost coming straight from China, but is on the low end so be careful.
Honestly, I'd strongly recommend getting the CR-10S as they upgrades, especially the board, are well worth it. They sell on Amazon for $599 https://www.amazon.com/HICTOP-Printer-Filament-Monitor-300x300x400mm/dp/B074QLQSQV and the Hictop is a solid build as far as CR10S go. You cold probably find a better deal on one from overseas.
If that price is too steep for you, and you are OK with a smaller bed size the Monoprice Select Mini is another good starter printer. For $220 you get a heck of a lot of printer: https://www.amazon.com/Monoprice-Select-Printer-Heated-Filament/dp/B01FL49VZE
Has anyone purchased this specific listing from Amazon? CR-10S HICTOP Rebrand Or this one from eBay CR-10S4 I'm looking to get a CR-10S either 300x300 or the 500x500 model but don't want to buy from Gearbest because I heard they're very bad. Any recommendations? Also for the 500x500 is there a model that has a larger heat area (not 300x300)?