#19 in Pipe fittings & pipes
Use arrows to jump to the previous/next product
Reddit mentions of PureSec 2020 Stem Elbow Connector 1/4-inch 90 degree elbow Push to Connect Plastic Quick Fittings for RODI System(10 Pack)
Sentiment score: 1
Reddit mentions: 2
We found 2 Reddit mentions of PureSec 2020 Stem Elbow Connector 1/4-inch 90 degree elbow Push to Connect Plastic Quick Fittings for RODI System(10 Pack). Here are the top ones.
Buying options
View on Amazon.comor
- ★WATER&FOOD USE MATERIALS: Our Stem Elbow Connector is made from safe,non-toxic materials.They are widely used for RODI system,plumbing or drip irrigation System etc
- ★SIZE&TUBE COMPATIBLE WITH:1/4" Quick Connect fitting X 1/4" Stem Plug;Fits standard 1/4 inch O.D. water tubing used on most Water purification systems ( check your tube size carefully before order)
- ★EASY INSTALLATION: New generation Non-Locking Clip technology offers an easy DIY installation without tools required, Just Push in to Connect.
- ★FUNCTION&QUALITY:A quick connect fitting is a coupling used to provide a fast, make-or-break connection of fluid transfer lines. Operated by hand, quick connect fittings replace threaded or flanged connections, which require wrenches. A broad of Sizes covers a broad scope of applications. Our quality system ensures a superior level of product quality.
- ★Notes: Our Water line adapter is reusable, it can be installed without Locking clips. it also can be used with Locking clips ( Search B07WXRMQPF and B07WYMZQBC to buy).
Features:
Specs:
Color | White |
Height | 6 Inches |
Length | 13 Inches |
Width | 10 Inches |
The only piece I had to fabricate is the little black cube in the top. I made that from a piece of 1/2" acrylic. I drilled a 90 degree hole into the top and side of it. Then used epoxy to attach it to the fan with the wires going through it. I had to snip the wire adapter off to do this. The holes I drilled into the cube were the exact same diameter of the male piece of the quick connect barb. This kept it snug but also allowed it to rotate in the hole.
Next, I then fished the wires through the quick connect fittings and through the quick connect bulkhead. After the wiring was all the way though, i re-soldered the wire adapter and used heat shrink tubing to seal it all together.
Once everything was wired up I connected the fans to a 4 channel PC fan controller and fired it up. I do have to say I am very happy with the results.fan closeups
All parts were bought on amazon or ebay. Mistkings fittings while black are nice, they are very expensive compared to the white ones I found on amazon. The fans were bought on ebay and were very cheap. I estimate I built 4 of the fans for about $30.00 USD
https://www.ebay.com/itm/Vktech-5Pcs-Black-Brushless-DC-Cooling-Blower-Fan-5015S-5V-0-1-0-3A-50x15mm-/183518100748?hash=item2aba87fd0c
https://www.amazon.com/gp/product/B00YGR2ILM/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B01MZ2PLCR/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
Pick up some of these, will enable you to route the tube flat against the top and out the back for a cleaner look. https://www.amazon.com/dp/B01MZ2PLCR/ref=cm_sw_r_cp_apa_i_yPQRCbDGAP8MA
Been considering doing a float valve with my breville to avoid constant filling.