#57,596 in Electronics
Use arrows to jump to the previous/next product
Reddit mentions of SoundOriginal 2pcs Brushless DC Cooling Fan 24V 0.06A 40mm x 40mm x10mm Speed 6800 RPM Fans for 3D Printer Humidifier Aromatherapy and Other Small Appliances Series Repair Replacement (Black 24V)
Sentiment score: 1
Reddit mentions: 2
We found 2 Reddit mentions of SoundOriginal 2pcs Brushless DC Cooling Fan 24V 0.06A 40mm x 40mm x10mm Speed 6800 RPM Fans for 3D Printer Humidifier Aromatherapy and Other Small Appliances Series Repair Replacement (Black 24V). Here are the top ones.
Buying options
View on Amazon.comor
2pcs Brushless cooling fan 24vdc 0.06A 40mm x 40mm x10mm Speed 6800 RPM Fans for computer case 40mm 3d Printer fan used in humidifier, aromatherapy and other small appliances series; small heat radiating communication equipment; military equipment; intelligent industrial control equipment plate cooling heat, high precision medical equipment cooling; pc cpu server cooling dissipation; electronic cooling fans and so on---Repair Replacement (2Pack)Bearing Type: Dual Ball Bearing, Speed: 6800 RPM, Dual-ball bearings have a lifespan of 67,000 hours and allows the fans to be laid flat or stand upright.Connector: 2 Terminal Connector with 2pin-ph2.5; compact motor design, the NF-A4x10's motor hub is smaller than with conventional 4cm fans. This allows for more blade surface area and thus contributes to the NF-A4x10's superior airflow and pressure performance.DC Brushless Cooling Fan, Rated Voltage: DC 24V, Current: 0.06A;Dimensions: 40x40x10mm (1.6 x 1.6 x 0.36inch). per fan | Total Airflow: 6.9 CFM | Total Noise: 34.5 dBA | Bearings: Dual Ball
Specs:
Color | Black 24V |
If you get an ender there are 4 safety things that I would do before I would print more than a test object or two and certainly before leaving it unattended
https://www.th3dstudio.com/knowledgebase/th3d-unified-firmware-package/
If you don't have an arduino or pi already laying around
https://www.th3dstudio.com/product/arduino-uno-bootloader-flashing-kit/
The first three are fire hazards that are simple to fix and don't cost much but are essential before leaving it unattended. The 4th item is a rare thing that could be a shock hazard caused by a loose screw or a misaligned insulation sheet in the PSU.
All together the 4 fixes will take 30 minutes or less and $30 or less... It would be nice if Creality would do it from the factory but so far they haven't picked up everything.
These are optional printed upgrades I would consider essential ... filament guides, cable chains, and part cooling nozzle....
https://www.thingiverse.com/thing:3426272
https://www.thingiverse.com/thing:3000563
https://www.thingiverse.com/thing:2917932
https://www.thingiverse.com/thing:3184816
Read this guide:
https://www.reddit.com/r/3Dprinting/wiki/newguideender3
Other general notes: The stock sd card and fans are junk and you should expect to replace them within 3 to 6 months.... they may last longer but don't be surprised.... for the sd card anything up to 32g works... for the fans you need 24v 4010 size ball bearing fans.. links below will do the job but your milage may vary.
https://smile.amazon.com/gp/product/B07L2WTH7H/
https://smile.amazon.com/gp/product/B07D6WXVHW/
Thanks again for the response. Just want to confirm if these fans are the right ones: https://www.amazon.com/SoundOriginal-Humidifier-Aromatherapy-Appliances-Replacement/dp/B07D6WXVHW/ref=cm_cr_arp_d_product_top?ie=UTF8 . 40x40x10mm 24v fan... I think its right but wanted to confirm with someone who knows more than I do heh.