Reddit mentions of CNCT 19-Pin USB3.0 to USB2.0 Adapter Header Cable - Suitable for use with USB 2.0 Based Mother Boards from Intel - ASUS - Gigabyte - MSI (1 PC)

https://www.amazon.com/CNCT-19-Pin-USB3-0-USB2-0-Adapter/dp/B00V3F44JO/ref=sr_1_3?s=electronics&ie=UTF8&qid=1510407749&sr=1-3&keywords=usb+3+header+to+usb+2+header

IF the USB-C uses a usb 3 header to plug into mobo , just grab you an adapter , it will basically only then work at usb2 speeds and support only usb2 charge rates but it will at least work :)

Plug it in here > https://image.prntscr.com/image/qsoGKh_0QU2eSFIl0ZmCHQ.png

I've already been looking into this a bit for possible options that don't include the connector on the board. Mainly AMD, minus the Impact board. Intel seems to have some options so it's less necessary. So far I found 3 possible options that I will probably try since I just got the Ncase today and there is no ETA on the Impact yet, and availability will probably be terrible.

1. Use a splitter cable and an adapter to plug both in at the same time. I believe this will only work when using one set of USBs at a time though.
   
   
2. Using the same adapter, if you happen to have dual M.2 slots, certain mobos might be able to make use of an M2 to USB3 header adapter. This should be able to run both at the same time although maybe not at the full speed.
   
   
3. Or the least desired option, having the adapter card in the USB3 header for USBC connector, and using a USB2 adapter to convert the USB3 type A into just normal USB ports.

Your motherboard doesn't have a USB 3 front panel header - it's only USB 2.0. If you want a front panel USB connection, you can use a USB 2 to USB 3 adapter, but it will run at USB 2 speeds.

That board does not have a USB 3.0 header.

You could downgrade the front panel to 2.0 with an adapter like this and use the internal 2.0 headers. https://www.amazon.com/CNCT-19-Pin-USB3-0-USB2-0-Adapter/dp/B00V3F44JO/

If you are not using a graphics card you could add a USB expansion card that includes an internal header. Just make sure it comes with a low profile bracket. https://www.amazon.com/IO-Crest-Internal-Components-SY-PEX20140/dp/B009LIPFEI/

No problem!

Also, side note, you'll have to buy a $3-5ish adapter if you want to use the ports on the front of the case because old Sandy Bridge motherboards don't seem to have USB 3 headers. Something like this: https://www.amazon.com/CNCT-19-Pin-USB3-0-USB2-0-Adapter/dp/B00V3F44JO/ref=sr_1_2?ie=UTF8&qid=1493477954&sr=8-2&keywords=usb+3+to+2+header

https://www.amazon.com/CNCT-19-Pin-USB3-0-USB2-0-Adapter/dp/B00V3F44JO/

Yes you can use an adapter if you don't mind the lower speed.

The problem is you have usb 3 connection on your case that you won't be able to connect to the motherboard.
The solutions are to find an adaptor (then you will have usb 2 instead of usb 3 on the front of your case), here an exemple http://www.amazon.in/dp/B00V3F44JO
or you go with a motherboard with a chipset h87 or h97

Lol so I have the NZXT USB extender thing. I also got this adapter for the onboard USB: CNCT 19-Pin USB3.0 to USB2.0 Adapter Header Cable - Suitable for use with USB 2.0 based mother boards from Intel - ASUS - Gigabyte - MSI (1 PC) https://www.amazon.com/dp/B00V3F44JO/ref=cm_sw_r_cp_apa_i_Z5pHDbARWVNH3

Its still a work in progress. Basically if you want an x570 board paired with the h210 case you have to pick your poison. I hate the idea of having usb in the front that don't work. Wish I got the h 200/h500 instead so I wouldnt have to put up with this..