Reddit mentions of 5 Pack Micro Spatula, Opret Lab Scoop Spoon Capsule Filler 0 00 for Powders Stainless Steel Gel Cap Filler

Not OP but, remove punger. Some have a cap for the end. You can put soap and water and the use a small lab brushes. Something like this set:

https://www.amazon.com/BasicForm-Cleaning-Bottle-Containers-Brushes/dp/B074MB1HS9/ref=sr_1_5?ie=UTF8&qid=1542365164&sr=8-5&keywords=lab+brushes

​

Lab spatula's are nice and long too

​

https://www.amazon.com/Spatula-Opret-Capsule-Powders-Stainless/dp/B07DCLJ1YT/ref=sr_1_2_sspa?ie=UTF8&qid=1542365194&sr=8-2-spons&keywords=lab+spatula&psc=1

​

​

Yeah just look into the solution and make sure it's clear.

Also make sure you're measuring your weight of substance and how much solution you're gonna use. I recommend the AWS Gemini scale. It's not accurate at super low ranges (hence the need for volumetric solutions), so you weigh out how much you're gonna use before hand. I like to weigh the bag before (full) and after (making solution) to compare how accurate the measurement was (obviously both could be off but they're usually within +/- 5mg which isn't much at this scale. (no pun intended lol).

A cardstock type paper is really good for weighing the powder with a crease down the middle, or what I use: cheap chinese wax weigh papers because the powder doesnt stick to them at all, and they're cheap and disposable. pour the powder into the vial (don't spill!) (here's a list of a bunch of bottles, it's hard to find what you exactly need and they usually come in big packs). My bottles actually came with a little aluminum funnel which doesn't work too good cuz the powder gets stuck to it, so I just kinda crease the paper and pour it into the vial opening very slowly being sure not to spill. Do it over a piece of paper or something if y ou're worried about spilling, since you've already measured it you can just take that paper and pour the "spilled" product into the botttle.

I don't have the full set of these but one of these like this with one scoop end and one flat end is really useful for the flat end to get into corners of baggies and whatnot, so I'd recommend something like this as a a scoop:

My vials are 60ml but I like to have extra space to shake the solution (important) so I only put 50ml at once to leave room for shaking. So say for 10mg/ml of etiz I would do 500mg etiz + 50ml PG. (1ml = 10mg, personal preference). If I was doing flualp I would do 100mg flualp 50ml PG. (personal preference of 2mg/ml since I usually dose between 0.6mg (0.3ml) and like 1.8mg (0.9ml).

To measure the PG you're gonna either need a graduated cylinder or, what I use which is probably slightly less accurate but there of course is a small margin for error as long as you know about the concentration, I use a 10ml syringe to fill the vial. 5 10ml pumps = 50ml.

For dosing lots of people will tell you to count the drops and that "there are 20 drops in 1ml no matter what" which is completely untrue, the only way to know exactly how much you're taking is using oral syringes. They're super cheapa if you can stand to wait a month from china, but you get like 20 (which is kinda required because after a while the lines start to fade on them. each tick is a 0.1ml so a full syringe is 1ml so if you have a 10mg/ml solution a full syringe is 10mg of etizolam, so if you only need 2mg or something it cuts down on the amount of PG you have to ingest. Lots of sites that sell premade solutions overcharge insanely for how little work it is to make yourself, and on top of that give you weak ass solutions like 2mg/ml (of etiz) or 4mg/ml (not even divisible by 10 so it gets confusing trying to dose that!) which make you intake way more PG than necessary. (It is food safe but it's pretty gross and some people can have adverse reactions).

Anyways...

There's lots of threads out there about this too if you need a full on step by step guide just google "etizolam solution" (most common one, it's the same for every substance, you just might want different concentrations for different strengths of drug). I tend to try and make my solutions as potent as possible so I don't have to eat an unnecessary amount of PG, or spend as much time making solutions!

Good luck and sorry for being judgemental earlier, glad you're at least willing to learn and I'm sure your friend was okay, just blew my mind knowing how I reacted to .250mg of flualp with no tolerance, lol.

Also you caught me on a pretty stimmy day so enjoy the fully cited guide, I don't think I missed anything. I don't necessarily use or endorse any of the specific products I linked just used them as examples of things you'd need; except the AWS Gemini 20, which is a must if you're weighing powders.

Sorry for the stim rant but I hope I helped out. Edited to add 1ml syringe dosing information.