Reddit mentions: The best lab utensils

Yeah just look into the solution and make sure it's clear.

Also make sure you're measuring your weight of substance and how much solution you're gonna use. I recommend the AWS Gemini scale. It's not accurate at super low ranges (hence the need for volumetric solutions), so you weigh out how much you're gonna use before hand. I like to weigh the bag before (full) and after (making solution) to compare how accurate the measurement was (obviously both could be off but they're usually within +/- 5mg which isn't much at this scale. (no pun intended lol).

A cardstock type paper is really good for weighing the powder with a crease down the middle, or what I use: cheap chinese wax weigh papers because the powder doesnt stick to them at all, and they're cheap and disposable. pour the powder into the vial (don't spill!) (here's a list of a bunch of bottles, it's hard to find what you exactly need and they usually come in big packs). My bottles actually came with a little aluminum funnel which doesn't work too good cuz the powder gets stuck to it, so I just kinda crease the paper and pour it into the vial opening very slowly being sure not to spill. Do it over a piece of paper or something if y ou're worried about spilling, since you've already measured it you can just take that paper and pour the "spilled" product into the botttle.

I don't have the full set of these but one of these like this with one scoop end and one flat end is really useful for the flat end to get into corners of baggies and whatnot, so I'd recommend something like this as a a scoop:

My vials are 60ml but I like to have extra space to shake the solution (important) so I only put 50ml at once to leave room for shaking. So say for 10mg/ml of etiz I would do 500mg etiz + 50ml PG. (1ml = 10mg, personal preference). If I was doing flualp I would do 100mg flualp 50ml PG. (personal preference of 2mg/ml since I usually dose between 0.6mg (0.3ml) and like 1.8mg (0.9ml).

To measure the PG you're gonna either need a graduated cylinder or, what I use which is probably slightly less accurate but there of course is a small margin for error as long as you know about the concentration, I use a 10ml syringe to fill the vial. 5 10ml pumps = 50ml.

For dosing lots of people will tell you to count the drops and that "there are 20 drops in 1ml no matter what" which is completely untrue, the only way to know exactly how much you're taking is using oral syringes. They're super cheapa if you can stand to wait a month from china, but you get like 20 (which is kinda required because after a while the lines start to fade on them. each tick is a 0.1ml so a full syringe is 1ml so if you have a 10mg/ml solution a full syringe is 10mg of etizolam, so if you only need 2mg or something it cuts down on the amount of PG you have to ingest. Lots of sites that sell premade solutions overcharge insanely for how little work it is to make yourself, and on top of that give you weak ass solutions like 2mg/ml (of etiz) or 4mg/ml (not even divisible by 10 so it gets confusing trying to dose that!) which make you intake way more PG than necessary. (It is food safe but it's pretty gross and some people can have adverse reactions).

Anyways...

There's lots of threads out there about this too if you need a full on step by step guide just google "etizolam solution" (most common one, it's the same for every substance, you just might want different concentrations for different strengths of drug). I tend to try and make my solutions as potent as possible so I don't have to eat an unnecessary amount of PG, or spend as much time making solutions!

Good luck and sorry for being judgemental earlier, glad you're at least willing to learn and I'm sure your friend was okay, just blew my mind knowing how I reacted to .250mg of flualp with no tolerance, lol.

Also you caught me on a pretty stimmy day so enjoy the fully cited guide, I don't think I missed anything. I don't necessarily use or endorse any of the specific products I linked just used them as examples of things you'd need; except the AWS Gemini 20, which is a must if you're weighing powders.

Sorry for the stim rant but I hope I helped out. Edited to add 1ml syringe dosing information.

I bought all my materials from Amazon and I've done about 3 Mods.

Heres a little documentation of my 1st one.

Seiko 5 Mod; PAM Cali Dial & Sword Hands & some more photos

Some things that I suggest you get before starting.

• Magnifier Opposed to a Loupe this works well and is rather convenient with 3 magnifications
  
  
• Precision Tweezers You need, need this. Seriously
  
  
• Crystal Press Self explanatory
  
  
• Dust Blower Often times you get dust on your dial while it sits, so get this to get rid of it
  
  
• Hand Press I don't particularly like the hand remover included but it does the job just fine
  
  
• Cushioned Holder I used this to hold the movement taking it out of the case
  
  
• Silicone Grease Used to grease the gaskets for increased water resistance
  
  
• Caseback Ball One of the best things you can get to be honest, it removes most casebacks
  
  
• Movement Holder To uhh, hold the movement
  
  
• Precision Screwdrivers You need this to unscrew the movement from the holders, also good tool to use for when you take apart movements to learn
  
  
• Hypo Cement Used this for bezel attachments for when you change em up
  
  Let me know if you've any questions, I'd be willing to help you out and answer them to the best of my ability :)
  
  Cheers!

Superglue doesn't work very well. Loctite 404 is the best I've found of the cyanoacrylates, but it tops out at "okay," unless you're willing to put in a lot of surface prep.

ABS glue works great, though it can be a pain to use. You want to make your own: get some acetone and some ABS. Undyed pellets are best, like this: https://www.amazon.com/IC3D-Printer-Plastic-Pellets-Natural/dp/B00MG5PF5M/ , though you should be able to find cheaper. Put some pellets in a small jar, and add acetone. You're probably looking to end up around 2 parts acetone to 1 part pellets by volume, but you can adjust it pretty far either way. Mix them together through a combination of stirring and shaking. This will take a while, and you'll probably need to let them soak periodically. They won't dissolve all the way without mixing, and they wont mix without soaking, so it's just going to take a while. Eventually though, you'll have a good that you can brush or squirt onto PLA to make it stick together. I mostly use mine with an industrial syringe, with a pin in the needle to keep a channel open. It's easy to dispense, and fairly convenient. For large applications or for painting onto a bed, I use acid brushes.
https://www.amazon.com/gp/product/B00NEUC8SK/
https://www.amazon.com/gp/product/B00DXPRTHG/

You can also weld pieces together with a dremel. This is a very good join for large pieces, especially with straight seams, but can be rough for detail work. There's a description here: http://www.scorchworks.com/Blog/friction-welding-with-a-dremel-rotary-tool/

Unable? Not so my friend! You just need to keep it sorta roomtemp as I understand. I personally keep mine in a fridge, but that's unnecessary I think. I use a small dark glass bottle, that holds 30ml - which I drop a tab into, and then use a blunted syringe to extract 1.5ml–3ml per dose (depending how much I want that day).

Volumetric is a WAY WAY better way of doing it than cutting up tabs. I'm sure if your bedroom is even a remotely normal room temp your little bottle will be just fine in a drawer or something.

The dark glass bottle, and the syringes (science/non medical type) are available on amazon for not too much money.

— Here is the type of bottle I have (these are very very nice, you could probably get away with a cheaper one, but hey, it's nice to have nice things :)

https://www.amazon.com/Infinity-Jars-Travel-Ultraviolet-Screwtop/dp/B00N5FLUYC/ref=sr_1_1?ie=UTF8&qid=1502672177&sr=8-1-spons&keywords=infinity+jar&psc=1

Measurement:
https://www.amazon.com/Duda-Energy-Syringepk010-Industrial-Syringes/dp/B00DXPRTHG/ref=sr_1_1?ie=UTF8&qid=1502672271&sr=8-1&keywords=Duda+Energy+Syringepk010+Industrial+Syringes+with+15G+x+1-1%2F2%22+Blunt+Tip+Fill


Math is easy. If you put a tab say a 100ug tab into 30ml of water, then if you take 3ml of that water, you would be getting 10% of that tab. 5—15% is usually a good amount, and you might find that less works better for you.

The ALD52 I have is 125ug per tab. So 125ug in 30ml of distilled water means that 3ml of solution equals 12.5ug of a dose - and often, I take half of that, so only 1.5ml of soultion.

Helpful info on the best water to use.
I use cold tap water. I also filter through a micron filter into 10ml amber glass resealable vials. I make my own bacteriostatic water by doing cold tap water with .09% benzyl alcohol. This ends up being 9.1ml of water and .09ml of benzyl alcohol. The benzyl alcohol I get comes in a 50ml resealable sterile bottle.

Here's a link to the 27 gauge 1.25" 3cc sterile needles I get. It comes as one unit with the needle already attached to the syringe. I get my vials, benzyl alcohol, needles, and alcohol wipes from medlabsupply. They have way cheaper pricing and everything you need is on there. Just make sure to get everything you need all at once to avoid paying too much for shipping. I use these 10ml syringes for making the actual solution. You can reuse these as long as you use a fresh micron filter as it will filter any potential bacteria.

You should really research how to do IM injections to avoid getting any abscesses/infections as you can lose a limb. IM is much less forgiving than IV as it's very easy for bacteria to spread in muscle tissue so infection needs to be taken much more seriously. You should be using a fresh needle every time, using alcohol wipes to wipe the top of your bottle of solution if you're using a premade solution, and wiping your injection site before you shoot it every single time.

I'd suggest making solutions since using a micron filter is much safer than a cotton ball. It makes it easier since you can just filter your entire solution at once and use only a single wheel/micron filter for one or two solutions (assuming your doing 10ml solutions). Then your whole vial is filtered and sterile and you don't have to worry about it until you go through the whole vial (1 gram of k per 10ml vial).

As far as injection sites the thigh is definitely the easiest and most forgiving. I'd say glutes are second. I just alternate between each thigh muscle personally. If I did it more often I'd do each thigh muscle and then one or both glutes (choose the one on the same side as your dominant hand if just doing one).

Here's a link that shows your how to find the site properly. Here's another one showing injection sites, how to find them, and how to do IM injections safely. This one is a good video for finding the injection for glutes and where your sciatic nerve is. Even after you know how to find the sites you should still look up images of the nerves that run through the given muscle you plan on injecting into. That way you can know exactly what you're avoiding and it'll will prevent accidentally hitting one.

I recommend this and these
It’s a set of vials and syringes. I would recommend getting a vial holder as well. That way, you have all the vials in one places and are not as likely to spill. The vials are nice because you can test small batch mixtures. Label the tops of the vials and keep a notebook. Rhodia is good or something else that can show off sheen. This way, you can more down the vial designation, the proportions, the inks used and what the resulting color looks like.

Another thing you would want to learn about is color therapy because a cool yellow mixed with a warm blue will give you a different green than a warm yellow mixed with a cool blue. Rot dye has a great mixing chart that is a wonderful resource for color mixing.

Beyond that, different inks interact and react in sometimes unexpected ways when mixed, which is another reason to have small vials to see what the reactions are and if the ink start to separate or do something else unusual.

This is definitely the recommended way to do it!

Also a related tip - for more portable dosing you can dissolve it into much smaller volumes (ie 10mg / mL), measure it out precisely with a 1mL/1cc syringe and store it in capped plastic centrifuge tubes.

That makes it easier you can hand out volumetric doses to friends, store them in your pocket for easy consumption later in the day, etc. I find 2c-b is one of the easier psychedelics to handle in social/public/crowded environments and it’s very redoseable, so it’s particularly useful to have a convenient way to take more on the go.

It’s also worth noting that 2c-b is a very hardy compound (like most phenethylamines) - it’s not as necessary to use any special water for it, it’ll stay potent dissolved in regular tap water for years. If you’re doing volumetric measuring with something more delicate like LSD then it’s very important to use water without any chloride, which will degrade it over time.

Glad you asked! One thing we have to remember about Prime is that it does not remove the ammonia, it just renders it harmless. So the result is a "false positive" on standard ammonia tests. It will still be there but it is no longer harming your fish.

If you would like peace-of-mind you can get a Free vs Total Ammonia test kit. This kit allows you to measure the amounts of Free (harmful) ammonia vs. the Total (harmless once Prime is involved).

Even if you aren't going to get some, read the description on Amazon. It is really helpful in understanding Ammonia chemistry.

For measuring ANYTHING for your aquarium, go to your local drugstore pharmacy (Even Walmart pharmacies will do this) and ask them for free syringes. They are absolutely AWESOME for measuring anything that takes very small measurements such as Prime. If for whatever reason you can't get some for free from a drug store, order a set like this. I use the 1ml and 5ml syringes every single day.

Edit: I suck at spelling....

look on amazon, between the item description and the "questions ask/answered" section regarding the product, i have seen some where this information is provided. 0.1ml is the amount delivered from one i saw i believe.

-

I recommend this one... it's 30ml but EASILY fits into your pocket.

-

the glass one here is much better then the plastic one from the same company, and i'm relatively sure it delivers 0.1ml per squirt

-

To make sure, simply fill it with an amount of water measured using an oral syringe (available for free at almost all pharmacys, just ask the pharmacist, say that your little brother got some medicine that requires one for measurement and needs it... though i prefer ones with a long blunt tip, available on amazon as well [here's the 10ml ones i often use and love] (https://www.amazon.com/Duda-Energy-Syringepk010-Industrial-Syringes/dp/B00DXPRTHG/ref=nav_ya_signin?ie=UTF8&qid=1467798872&sr=8-2&keywords=10+ml+blunt+tip+syringe&)

-

and [here's some 1ml ones] (https://www.amazon.com/Duda-Energy-Syringepk001-Industrial-Syringes/dp/B00NDETMR2/ref=sr_1_1?ie=UTF8&qid=1467798956&sr=8-1&keywords=1ml+blunt+tip+syringe) that i got but haven't tried yet, they reviewed well though

Explosive Elephant Toothpaste!! edited to correct ingredient - and update notes

My goal was big, shooting foam steams! I tried other methods and recipes - but this worked best!

What is happening in elephant toothpaste: hydrogen peroxide is made up of two hydrogen and two oxygen molecules. This is one extra oxygen molecule than water. Hydrogen peroxide is very unstable; it keeps wanting to lose that extra oxygen molecule. In this experiment, we use potassium iodide as a catalyst to knock off that extra oxygen molecule very quickly, and soap to capture those molecules of oxygen in foam.

I tried this with two different flask types: 2L Erlenmeyer flask and 2L graduated cylinder.

For each flask I needed the following:

• 250ml 35% H2O2 (hydrogen peroxide)
  
• 50ml 4 molar KI (dry, granular potassium iodide)
  
• a bit of dish soap
  
  To get (my best approximation of) 4 molar KI, I put 35 mg of nearly-pure granular KI in a small glass measuring beaker, and filled it to 50 ml with cool tap water.
  
  If you use smaller flasks, you will need to cut the ingredients by about 1/2.
  
  I was able to buy the chemicals and all the flasks online. Please be careful with the hydrogen peroxide – it will burn your skin at this concentration.
  
  The result is soapy water - but there may be some residual hydrogen peroxide. Simply rinsing the area well should be sufficient.
  
  Steps:
  
  Pre-make the KI solution, and measure out all other chemicals.
  
  USING GLOVES AND EYE PROTECTION
  
  -- Put 250ml H2O2 in each flask
  -- Put ~25-30 ml of dish soap in each flask
  -- Add a few drops food coloring of color desired (complicates clean-up - be warned!)
  -- QUICKLY add 50 ml KI solution to each flask and jump back!
  
  Notes:
  
  The graduated cylinder produces a thick pillar of foam, the Erlenmeyer flask produces more of a jet.
  
  The chemicals should be added by an adult.
  
  If you film this, be sure to have the person filming stand back, and be prepared to capture an 8 to 10 foot jet coming out of the flask.
  
  Shopping list (what I used):
  
  This puts out a thick column of foam:
  213I16 Karter Scientific 2000ml Glass Graduated Cylinder, Single Metric Scale ‪https://www.amazon.com/dp/B006UKIBKU/ref=cm_sw_r_cp_api_8OuWxbG8YRB8N‬
  
  This puts out a narrow/taller jet of foam - I now have three:
  2000ml / 2L Narrow Mouth Erlenmeyer Flask with Heavy Duty Rim ‪https://www.amazon.com/dp/B00Q34D0HC/ref=cm_sw_r_cp_api_rQuWxb4708ZVJ‬
  
  Pure Health Discounts Certified 35% Hydrogen Peroxide with 1 oz Bottle Dropper - 32 oz https://www.amazon.com/dp/B01AKIGJW4/ref=cm_sw_r_cp_api_YD4pzbZTGXC86
  
  Potassium Iodide, High Purity Crystals, 99.8 % min., 100 grams ‪https://www.amazon.com/dp/B008D8161I/ref=cm_sw_r_cp_api_PTuWxb0N94SZQ‬
  
  Atlas Glove 620 Atlas Vinylove 12" Double Dipped Gloves - Small (they come in different sizes) ‪https://www.amazon.com/dp/B002PJ0WRK/ref=cm_sw_r_cp_api_nUuWxbSQCV77N‬
  
  Learning Resources Primary Science Safety Glasses (good size for kids) ‪https://www.amazon.com/dp/B006ZLSWFI/ref=cm_sw_r_cp_api_SVuWxbBKKKD9R‬
  
  Heathrow Scientific HD15909 Spatula with Flat End and Spoon End, 9" Overall Length (optional - but good for mixing the potassium iodide) ‪https://www.amazon.com/dp/B0061OT1A4/ref=cm_sw_r_cp_api_qSuWxbA6R27C3‬
  

You can get a good scale for about 20 dollars. Make sure to have you scale on a level surface(you can buy one of those levels with the bubble in it for like 3 dollars) and make sure to calibrate your scale before every use. Also keep your scale clean and make sure you keep it somewhere where it won't be dropped or anything.

Here's a good scale

Here's a cheap reliable level

Here's a nice little scooping tool for your powders

Stay safe my friend!

Wow, thanks for the thorough answer!
I'm set on trying a new roa for this trip. I think a boof will be a nice little experiment and I do actually want a shorter trip. I can't imagine what 40mg is like ha, dang. I've read that once you start getting past like 30mg, it becomes extremely milligram sensitive.

this is the only syringes I have https://www.amazon.com/gp/aw/d/B0161V0024/ref=ya_aw_oh_bia_dp?ie=UTF8&psc=1
Will it be ok to use if I take the needle off? How about I just keep the needle on and squirt it up my urethra?

......excuse my dry humor -_-.......

Even if I use just 1-2ml of 4 aco dmt water, it seems like it would still flow out. Has that ever happened? Am I going to have to do the classic 'clench'?

Btw, I think I was being a bit brash about the beer. Sipping it while tripping would probably be an experience of its own. I've experienced synesthesia before (particularly tasting colors). I'll probably do some blindfolded fruit eating experiements - I'll chop up various fruits on a plate and eat random pieces without knowing which ones are which.

The setting is prettt much going to be my yard. Just chilling under the sun with beer and earphones.
I've smoked heavily on every trip so far (dxm,shrooms, 4 aco). The only difference this time is the t break. I don't see how one hit can spiral it out of control though.

I don't know if anyone else does this, but one trick I've used to extend the lifespan of my syringes is to wrap the exterior in clear packing tape. It helps prevent the ml markings from wearing off and makes them much easier to wipe/down and/or clean when you are finished.

Not really relevant, but it might come in handy for someone coming into the thread.

Also, these dispensing tips are fantastic for filling tanks/kayfuns/foggers/etc.

I have fallen completely in love with pens and their portability/strength. I use one of the 510 batteries from Curaleaf (free on first purchase) and I bought refillable ccell cartridges from here and syringe tips for easy refilling. I am able to control the temperature and length of hit perfectly. The taste is great and I do not experience that awful taste like I did when I used atomizer-based vapes, if that's what you're referring to.

For shatter I will use my Yocan Evolve, when I can get my hands on the stuff...tru shatter sells out right away!

2nd link is just a cap... You can use a push on needle tip works fine. The first link will "lock" the needle onto syringe but not 100% necessary... If you get something like this https://www.amazon.com/gp/aw/d/B01K1VO3E6/ref=pd_aw_fbt_328_img_2?ie=UTF8&psc=1&refRID=CTE7TVHA387F1V8PPMNE sorry i don't know how to do link how you did...

You can just push it on the syringe really hard and warm up the syringe with a couple passes from a lighter... It comes out pretty easy once warm.. Warm the carts to so oil flows to bottom easily...

My Vision II spinner has 4 settings 3.3V 3.8V 4.3V 4.8V.

You should feel subtle effects like improved mood, less anxious, more energy, might have slight enhanced interest in colors, music sounds better. If you see any traces, distortion or waviness in your vision you're taking too much for a microdose.

Me personally, I can feel .05g, I prefer .1 or .2g, if I take .3g I can see tracers of my finger tips as I move them across a dark background in a dim room. But that effect only lasts for less than 30 minutes, that's my upper limit for a microdose.

I got one of these to use when filling my capsules, works great!
https://www.amazon.com/gp/product/B005WX4URE/ref=ppx_od_dt_b_asin_title_s00?ie=UTF8&psc=1

Yes. Quite easily. The relationship is the following

If i have 1lb of force and want to lift something that weighs 4lbs i'll need two pistons right?

piston A with 1lb of force will have a surface area (pi*r^2) of idk, .5sqin.

piston B with 4lbs of load that you want to move will need a surface area 4x higher than piston A. so 2 sqin in this case.

The problem is when you move piston A 2 inches piston B (with the 4lb load) will only move .5 inches.

This scales linearly so if you want to lift a car with 1lb of force you can. but you better be able to move the piston a long long way to get the job done.

EDIT: a kit like this with some tubing will give you everything you need to demonstrate this at home. I don't know the tube diameters but you can measure them and figure out the ratio pretty easily. https://www.amazon.com/Pack-Refilling-Liquids-cigs-juice/dp/B01CFJ51X4/ref=sr_1_5?keywords=syringe&qid=1562950408&s=gateway&sr=8-5

This is the same thing I posted in response to a similar question a while back.

I'd suggest the Hakko FX-888D as it is a cheap temperature controlled station and you'll get better results quicker than with a cheap iron. You certainly can go with a cheaper Weller station but you may end up fighting with it a bit if you move beyond very basic work. For solder, stick with leaded 60/40 or 63/37 as it will flow out easier and at a lower temperature. Don't forget useful things like solder wick/desoldering braid, tweezers, and cutters.

To practice, start collecting old electronics and removing parts. Once the parts are out, put them back in. This will get you comfortable with the techniques without risking something valuable. The other option is to go to eBay and buy cheap kits from China for a few dollars and build them.

Pace has some outstanding soldering videos on YouTube. They are a bit old but are quite well done and still relevant. I'd suggest you start with these then look up the NASA soldering specifications to see the extreme end of things. You won't do much of what is in the NASA spec but it will give you some good background info.

iFixIt has a soldering tutorial (though it has a few bad habits in it).

2% is NOT high thc....it’s extremely low! I’d also recommend to use a heavy indica strain given what you’ve reported since you’re looking for more calming effects vs. high energy. Your specific condition could be the cause of how you’re not feeling any effects, so it’s probably best to significantly bump up your intake.

Buy distillate syringes ($65 at Surterra) and just make infused coconut oil. Distillate is up to 90% thc and will go a long way....Plus you can truly control your dosages by concentrating them as much as you’d like.

All you have to do is heat up unrefined coconut oil in a Pyrex container, put the distillate into the hot oil and start stirring for a few minutes. Once it emulsifies it’s ready to use. The distillate is very thick, so put the syringe into hot water for a minute So that it becomes less viscous and then remove the cap to dispense it.

Example - let’s say there’s 850mg of thc in one distillate syringe and you use 50ml of coconut oil.

850/50 = 17mg of thc per ml of oil. You aren’t just limited to using one distillate syringe - feel free to use more to make your infused oil more potent.

Buy a blunt tip luer lock syringe with ml measurements and then simply put it into your own empty capsules. You can buy the syringe and the capsules on amazon for very cheap. You can also use these blunt tip syringes to measure your coconut oil to ensure he dosages will be right. Links to the items you need below

https://www.amazon.com/Pack-Refilling-Liquids-cigs-juice/dp/B01CFJ51X4/ref=mp_s_a_1_1_sspa?keywords=blunt+tip+syringe&qid=1554677628&s=gateway&sr=8-1-spons&psc=1

https://www.amazon.com/NOW-Gel-Capsules-250-Empty/dp/B00E40DJ82/ref=mp_s_a_1_7?crid=3VTB07WR7494G&keywords=capsules+00&qid=1554677715&s=gateway&sprefix=capsules&sr=8-7

You can also dispense the distillate straight into your own cartridges and vape it, but be sure to use only a ceramic cartridge. Do not include any coconut oil into your vape...just distillate

Hey dude! I purchased a starter kit when I started making E-juice, and while it was helpful I quickly realized that I could of gotten more for less had I known what I needed. It is a lot cheaper to just buy the products individually since you will also be getting a larger amount too. Here are some links and in my opinion this is the cheapest way for someone to start DIY:


VG- https://www.amazon.com/Glycerin-Vegetable-Kosher-USP-Quart/dp/B004C7MTLA/ref=sr_1_2_a_it?ie=UTF8&qid=1480546689&sr=8-2&keywords=vegetable+glycerine


PG- https://www.amazon.com/Essential-Depot-Propylene-Glycol-Quart/dp/B005F5OJG6/ref=sr_1_3?ie=UTF8&qid=1480546865&sr=8-3&keywords=propylene+glycol


Gloves- https://www.amazon.com/Liberty-Glove-Industrial-Disposable-Thickness/dp/B01MZZ0FHO/ref=sr_1_2?ie=UTF8&qid=1480546913&sr=8-2&keywords=nitrile+gloves


Syringes- https://www.amazon.com/10-Pack-Refilling-E-Liquids-Applicator/dp/B01HFTYINS/ref=sr_1_6?ie=UTF8&qid=1480546884&sr=8-6&keywords=blunt+tip+syringe


Nicotine- https://www.nudenicotine.com/products-page/unflavored-nicotine-base/

And as for bottles it is all up to you I personally buy mine from http://wholesale.heartlandvapes.com/eliquid-bottles/plastic-eliquid-bottles.html

*Lastly all you need is flavorings, I think it would be best for you to search around and find what you like, I personally prefer http://gremlindiy.com/ and http://www.bullcityflavors.com/ . Hope this helped!

so, first and foremost, we're far more active on /r/RATS. (im basically subbed here to tell people this).

but, im currently going through this with two of my boys. They're both on antibiotics and an anti-inflammatory. What you can do in the mean time though, is take him into the bathroom and run the shower as hot as possible. Just hang out with him and let him breathe in the steamed air. You can dilute some honey in some water and feed that to him. I suggest getting a non-needle syringe. something like this. you can find them at pharmacies. You can use this to feed him water and the honey mixture. Dark chocolate is good too. there's some sort of chemical in that that helps them breathe. I also heard you can give him rosemary but ive never tried that.

The biggest thing that helped was firm tapping with my finger on the side of his body right behind his arm. Dean boggles now when i do this to him and he's not even really sick anymore.

On the syringe... here is what I have:

https://www.amazon.com/gp/product/B01MQ0IIQK/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

Blunt tip stops you from stabbing yourself. I recommend you check out YouTube how to videos. Goulet Pens has brilliant, helpful videos.

You have good advice below about the feed and "unknown leak". Don't be sorry for asking. You will learn a butt load if you stick around. :O)

The Capsule Machine x4

You can knock out 96 caps, one after the next. If you fill the capsule machines by doing the tops all at once, and then the bottoms. You'll find that it's much more efficient.

http://capsuleconnection.com/home-capsule-machine/the-capsule-machine.html


The most important part is the Luer lock bottles. They provide the ultimate control and efficiency. I can cap 4-cups of oil in under two-hours. With a varying selection of syringes it was taking four to five hours. What's worse is you have this giant bowl of odorous oil filling the air. Placing all of the oil in bottles virtually eliminates that odor. Fill em up and then lick the bowl, spoon, and micro funnel. You'll need it for the mind numbing repetitive task ahead. If you bust through it you'll be handsomely rewarded at about the same time you finish.


60ml (2oz) Luer Lock Bottles - 8 Bottles will hold the 2-cup MBM minimum requirements
https://www.amazon.com/dp/B00BPW36S0/

18g Luer Lock Needles
https://www.amazon.com/dp/B001QQ6MO0/

There you have it. A fast, efficient, and virtually mess free experience.

Hello, do not mix distillate with pg/vg. It will precipitate out. People say you can vape pure distillate in ceramic carts/pods but it might be slow to get started because it's so thick. What you want to do is get some flavorless terpenes to thin out the distillate.

This is what I see recommended a bunch but there are others: https://buy-terpenes.com/products/viscosity/viscosity-extract-liquifier/


I'm in the same boat as you so this is my process:

I bought a small beaker:
https://www.amazon.com/gp/product/B003TVF9WQ/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
and some blunt-tip syringes:
https://www.amazon.com/gp/product/B06Y2JWDQ3/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1


I'm going to place the distillate in the beaker and microwave for 10 seconds.
Add 4 drops of Viscosity and stir well with the tip of a syringe.
Repeat, if needed, until a decent consistency, then transfer to the pod using the syringe.

*don't let the distillate get too hot as the terpenes and CBD will start to vaporize/evaporate past a certain temp.

​

Ideally you'd want to use a hot plate with a magnetic stirrer, but those are a bit expensive if you're not running a commercial operation.

​

​

Bent tweezers work really really well. Unless you're trying to take apart already mounted switches, I find tweezers to be the best (something like the top one in the picture on this listing http://www.amazon.com/Non-magnetic-Curved-Tweezers-Forceps-Anti-static/dp/B00DVIEJ14/ref=sr_1_2?s=industrial&ie=UTF8&qid=1409881252&sr=1-2&keywords=tweezers).

I don't have those specific ones though, so I can't comment on the quality of those. Nice reviews though.

Right here: http://www.amazon.com/gp/aw/d/B00DXPRTHG

I love these things. Perfect for dosing. Could have used less than 10 but I'm glad I got them. I Velcro them to their respective bottles.

Please please please use the correct tips. Throw that thing in a sharps container somewhere and order these instead

Edit: Also for the love of god, everyone use a sharps container. Your trash guy doesn't need that struggle.

Thanks for the cool tek! That sounds like its a worth a shot.

I have some of these syringes on their way to my house. :)

Look into paced bottle feeding. ALL fake nipples have too fast a flow for babies b/c the milk comes out whether baby is actively sucking or not. Video example.

I have had my kids on bottles at different points in their development and I also exclusively breastfed. My first was doing bottles from the first day in the hospital...but it caused a lot of issues with my supply and baby's latch. We had problems for 6 full weeks...that slowed significantly with her age, but eventually I gave up pumping by 5.5 months, and breastfeeding at about 10/11 months. My mom gave her milk with a spoon b/c she struggled with a bottle.

My second...This time I waited until "milk supply was established" as was recommended at the time...around 3ish weeks maybe? She took bottles pretty well and then one day just stopped. And it happened to be the day I was hours from home. My husband kept texting that she didn't want the bottle and I was like, "She'll get hungry enough eventually..." and she never did. When I got home she' hadn't eaten at all for 6-8 hours except for the drops my husband got in when she was sleeping...he squirted it into her mouth. I didn't realize the extent of the "not eating" bit...or I would have told him to use a spoon or something. From about 4 months on...she did not take a bottle.

My third...When she was about 6 months I tried to give her a bottle. She drank it while staring at me (I was across the room) the whole time. When it was empty she took it from my husband and chucked it. She even yelled. And that was the last bottle she ever took. Luckily, b/c of her age, I could give a cup occasionally, but I wasn't working and only pumped occasionally to relieve pressure if she missed a feed or something.

IF bottles are not working at all you can try other methods: A soft sided cup or specialty cup. A large syringe. Or even just a small spoon. Yes. All of these methods will take longer than a bottle. But if the goal is to feed baby pumped milk - then they will meet that goal.

There's a great guide to racetams here https://www.reddit.com/r/StackAdvice/comments/4g6p0i/racetams_and_you_a_guide_of_the_popular_racetam/

If you decide to go with powders (which is more cost-effective in the long run) make SURE you get a good scale to measure everything out. I went with this onehttps://www.amazon.com/gp/product/B0012TDNAM/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
and this to measure everything out https://www.amazon.com/gp/product/B005WX4URE/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

Super important to note that guinea pigs can’t produce vitamin C and need supplements. You can also get liquid vitimin C and small syringes from a vets office or online to give them daily. Mine think it’s a treat!

Examples:

Vitimin C: https://www.amazon.com/dp/B00016RLSC/ref=cm_sw_r_cp_awdb_t1_XgPPDb6004AC1

Syringes: https://www.amazon.com/dp/B01N01TO2O/ref=cm_sw_r_cp_awdb_t1_ziPPDb57CGQPG

The syringes can be rinsed out with water and reused!

Right before I graduated from college I was getting into soldering and decided once I got my diplomas I would treat myself to some nice HAKKO equipment using the 30% discount while I was still considered a student. The stuff below is what I purchased. Note that the 30% discount is only applied to the soldering station nothing else. Anyway, if you can splurge, I highly recommend the FX-951-66. It is truly fucking AWESOME. If you are on a tight budget and not sure if soldering as a hobby will stick, get the cheapest HAKKO they sell and it will still be a good unit. I am a huge fan of hakko so clearly I am biased but they are a well-known reputable brand

Hakko Soldering Station, FX-951-66

Hakko T15-JS02 Conical Bent Tip R0.2 / 30deg x 1.6 x 7.9mm for FX-951

Hakko CHP 3-SA Stainless Steel Non-Magnetic Precision Tweezers with Very Fine Point Tips for Microelectronics Applications, 4-3/4" Length

Hakko CHP-170 Micro Soft Wire Cutter, 1.5mm Stand-off, Flush Cut, 2.5mm Hardened Carbon Steel Construction, 21-Degree Angled Jaw, 8mm Jaw Length, 16 Gauge Maximum Cutting Capacity

There are blunt ones?

Man that would be a lot better than the huge (in needle sizes) needle that I've been using for the past couple of years.

Maybe Amazon has them...

Yep they do, this looks useful, thanks e-cigs: https://www.amazon.com/dp/B072XFYXVB/ref=cm_sw_r_cp_awdb_t1_nydYCbDN7F0BP

In that case, the syringe is pretty handy to have. I got this variety pack from Amazon < link > so I could try different sizes, and the 1ml (smallest one) ended up working the best for me to load the B-coil.

Not OP but, remove punger. Some have a cap for the end. You can put soap and water and the use a small lab brushes. Something like this set:

https://www.amazon.com/BasicForm-Cleaning-Bottle-Containers-Brushes/dp/B074MB1HS9/ref=sr_1_5?ie=UTF8&qid=1542365164&sr=8-5&keywords=lab+brushes

​

Lab spatula's are nice and long too

​

https://www.amazon.com/Spatula-Opret-Capsule-Powders-Stainless/dp/B07DCLJ1YT/ref=sr_1_2_sspa?ie=UTF8&qid=1542365194&sr=8-2-spons&keywords=lab+spatula&psc=1

​

​

How about...

https://www.amazon.com/EXELint-Disposable-Syringe-Sterile-Catheter/dp/B010BWOOXA

60ml = 2oz

Or maybe this one with a tube:

https://www.amazon.com/Momok-31-5inch-dispensing-injection-filtration/dp/B072Z7WVR6

You could have three or so and when you're done clean them. One for the chemical, surfactant, and marker. (Though the latter two I just glub glub into my mix. 😊)

Look on Amazon they sell them their for decent prices.

Here are the ones I picked up and they have worked great.

(Bstean Syringe Blunt Tip Needle and Cap)[https://www.amazon.com/dp/B01HFTYINS/ref=cm_sw_r_cp_apa_i_uNE3CbDYR36ZN]

I hope I edited the link correctly.

This is my obligatory post telling you try out tweezers:

http://www.amazon.com/Non-magnetic-Curved-Tweezers-Forceps-Anti-static/dp/B00DVIEJ14/

My producitivity almost trippled on making beadsprites, and my accuracy went way up, once I got precision tweezers. Well worth the $4 price tag.

Your sprites looks great by the way!

Thanks for the reply.

What do you use to scoop the solid oil into the caps?
Something like this?

https://www.amazon.com/Stainless-Reagent-Sampling-Spatulas-8-8inch/dp/B01M3P2R19/ref=sr_1_2?ie=UTF8&qid=1501544919&sr=8-2&keywords=powder+scoop

Ha, right? I always feel awkward ordering syringes/needles, but in reality the gauge you need to pull oil is far to large to easily fit under skin...but try explaining that one without a side look. I buy type 2 fill needles (http://www.amazon.com/Industrial-Syringes-Blunt-Needle-plastic/dp/B00DXPRTHG/ref=pd_sim_0_2?ie=UTF8&dpID=21SzolFINTL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=1W5Y0DNPKFJYV3SEHG0Z)

I get mine from amazon.
https://www.amazon.com/gp/product/B016Q5YVK2/ - Assorted sizes set (out of stock)
https://www.amazon.com/gp/product/B0187LGYCG/ - 5ml Airless Pumps (about the size of my thumb)
I would LOVE to find a glass airless pump bottle though!

A fill syringe is awesome for decanting. You don't have to touch the product, and don't expose as much to air! I got the kind for glycerin and they work pretty well. The thicker creams are a pain, but you can use a syringe if you have patience.
https://www.amazon.com/gp/product/B01CFJ51X4/

Good news, they're even cheaper than I said. $6.99

Aozita 6 Pack Lab Spatula - Micro Lab Spoon/Scoop with Nickel-Stainless Blade - Also Great Filler https://www.amazon.com/dp/B075VLJQDZ/ref=cm_sw_r_cp_apa_i_A-bwDbPB9Z2P8

I'll hook up bro!
Use ecig express to order Flavor Concentrates and bottles
— Use ELRECIPIES for 10% discount

Use The Flavor Apprentice/The Perfume Apprentice for Flavor concentrates
— Be sure that they are made for ecigs
— Better than ecig for bulk orders

Buy vegetable glycerin, and syringes from amazon
— Buy a gallon for bulk
— Buy 10ml, and 1ml syringes
— Buy Tupperware or something to contain 16 oz of liquid to steep ejuice

Buy nicotine from Nude Nicotine
—Purchase “Smooth” Nicotine salts



https://www.amazon.com/Duda-Energy-Syringepk001-Industrial-Syringes/dp/B00NDETMR2/ref=pd_lutyp_bia_3_4?_encoding=UTF8&pd_rd_i=B00NDETMR2&pd_rd_r=S32X53GMX38H2DP662TC&pd_rd_w=NhTrE&pd_rd_wg=Rt1HG&pf_rd_i=desktop-typ-carousels&pf_rd_m=ATVPDKIKX0DER&pf_rd_p=2798022962&pf_rd_r=S32X53GMX38H2DP662TC&pf_rd_s=desktop-typ-carousels&pf_rd_t=40701&psc=1&refRID=S32X53GMX38H2DP662TC

https://www.amazon.com/Duda-Energy-Syringepk010-Industrial-Syringes/dp/B00DXPRTHG/ref=pd_sim_328_5?_encoding=UTF8&pd_rd_i=B00DXPRTHG&pd_rd_r=G7GP5J47E1CRQPHET2VD&pd_rd_w=yULCb&pd_rd_wg=yRWOy&psc=1&refRID=G7GP5J47E1CRQPHET2VD

https://www.amazon.com/gp/product/B00PSGWHIO/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

https://www.ecigexpress.com

http://shop.perfumersapprentice.com

https://www.nudenicotine.com/product/nicotine-salts-smooth/

It depends on what you want to take. The dosages on here range from 2.5,5 to 10, 10 being the most. People seem to swear by the 2.5-5 range but I personally like 10. Maybe try 5 your first go around.

So here’s how I would do it

Get PG solution bundle from the source below, it has the solution and dropper bottles.

https://whitewaterresearch.com

And get a beaker from amazon, this is what I have

Karter Scientific 214T2, 3.3 Boro, Griffin Low Form, Glass Beaker Set - 3 Sizes - 50ml, 100ml, 250ml https://www.amazon.com/dp/B01F47B8AO/ref=cm_sw_r_cp_api_i_ZCUyDb3YNPV8V

I would personally make a 50 ml solution.

Take the 50 ml beaker, fill up to 50ml line, dump in powder, mix (it may need to sit), poor into bottles and you’re done.

With that ratio of 50ml to your 1mg of powder you are looking at 20mg per ml (one dropper full)

So then you just math what you want. If you want to take 10mg then it’s half the dropper, if you want to take 5mg then it’s 1/4 the dropper.

If you want to be super precise with your dosing you can get one of these

BSTEAN 1ml 1cc Syringe with Luer Slip Tip, No Needle, Non-Sterile (Pack of 50) https://www.amazon.com/dp/B01N01TO2O/ref=cm_sw_r_cp_api_i_OGUyDb8DK6M6F

I personally like these because it does make it precise and the pipettes that come with the bottles tend to be shit.

Aozita 6 Pack Lab Spatula - Micro Lab Spoon / Scoop with Nickel-Stainless Blade - Also Great Filler https://www.amazon.com/dp/B075VLJQDZ/ref=cm_sw_r_cp_apa_i_c7L4Ab1MJWBBN

Use these at work. Should do the trick for reaching the bottom of a container without breaking the bank.

Yes. Don't mix it with any other juice.

This is what I did with my vape oil.

I got this from Max vapor nail. Refillable cartridge:

https://maxvapornail.com/collections/featured-products/products/glass-cartridge-with-ceramic-core-and-preheater-coil

You can use one of these pens right here for $24 with a charger:

https://o2vape.com/product/oil-vaporizer-battery-white/

I bought syringe from Amazon to use to fill the cartridge:

https://www.amazon.com/Pack-Refilling-Measuring-E-Liquids-Adhesives/dp/B01CFJ51X4/ref=pd_sbs_328_3?_encoding=UTF8&psc=1&refRID=ZK0EQ5Z4GBTKGNMP9ZWF


Hope this helps you. Here is the review I did on vaping using a refillable cartridge.

https://www.cbdreviews.net/max-vapor-nail-glass-cartridge-with-ceramic-core-preheater-coil/

https://www.amazon.com/Syringes-Scientific-Measuring-Watering-Refilling/dp/B07C71C1LH You're thinking like this style of syringe? I'm sure there's syringes out there with nozzles that would be just fine for grease.

That being said, is there a budget number you had in mind?

To add on to OP, a good solution for dosing in smaller tanks:

[Syringes](1ml 1cc Syringe with Luer Slip Tip, No Needle, Non-Sterile (Pack of 50) https://www.amazon.com/dp/B01N01TO2O/ref=cm_sw_r_cp_api_6dnLybHRB4RVD) with blunt tips. They come in a range of sizes, but this one is good for 10gallons especially! I dose around 0.8mL twice a week.

all it takes is a bit of simple math. you can buy everything you need aside from the liquid nicotine on amazon. i myself use 100%vg juice so i dont buy pg at all but a large bottle of vg will run you about 20 to 25 dollars, 1 gallon for me is 22 at the moment. you can also find packs of empty bottles for around 10 bucks, then youll need measuring syringes for mixing, flavor drops and the nicotine all of which are linked below.

i would just mix small batches first if you arent sure what a juice would taste like after your done then mix a full bottle, this way you can experiment with flavor mixes and see what you can create.

for a 100 ml bottle its really easy youll just need to figure out how much nic to put in, i vape at 6% nic so i measure out 94 ml of vg and the last remaining 6 ml i put in as the nicotine, after that the base is done, then just drop in the flavor drops, shake it like crazy, let it settle for a bit and boom juice done.

there are also some sites out there with premade mixture recipes that you can find and follow

https://www.amazon.com/gp/product/B007HSDNS4/ref=ox_sc_act_title_1?smid=A3O37MU47F4102&psc=1

https://www.amazon.com/gp/product/B007Y8UX80/ref=ox_sc_act_title_2?smid=A1ZOAQ4ZHE42HG&psc=1

https://www.amazon.com/gp/product/B01CFJ51X4/ref=ox_sc_act_title_3?smid=A35C2NGNUSD9X5&psc=1

https://www.amazon.com/gp/product/B00WUPUYCC/ref=ox_sc_act_title_4?smid=A2S5SG4CMI156J&psc=1

https://liquidnicotinewholesalers.com/250mg-nicotine-liquid.html

Looking at these right now. The BPC is being used for an intestinal issue so won't be sub-q. Think these are good enough for just reconstituting the BPC, then drawing for putting each dose into an enteric coated capsule?

10ml Industrial Syringe with 18 x 1.5 Blunt Tip Needle Protective Cap included 5 PACK https://www.amazon.com/dp/B01M2CC95H/ref=cm_sw_r_sms_c_api_FONczb3PTDQA5

Or this

BSTEAN 5 ml Syringes with 18Ga 1.5 Inch Blunt Tip Needle and Storage Caps, (Pack of 10) https://www.amazon.com/dp/B01MQ0IIQK/ref=cm_sw_r_sms_c_api_mTNczb748RR6S

Thanks for being so patient and informative about all this!

>Nah, regular tweezers are less narrow most of the time.

these suckers are my go to, are $5 a pair, are insanely strong, yet are so dang narrow that I regularly stab myself to the point of drawing blood while aimlessly twiddling them

https://www.amazon.com/Hakko-3-SA-Non-Magnetic-Microelectronics-Applications/dp/B00FZPEWI6

but yeah, the msafe jack is a series of tiny neodiddlys covered by a thin piece of plastic. but yeaher, if you have five bones to spare and want to expereince the best bang for your buck tweezers money can buy, I can't endorse these guys hard enough. I used to be big on aven which are a budget japanese brand and cost 5X more, yet aren't as well built or rugged. CHP for life

This looks like a micro lab scoop I'd use to weigh out powdery substances at work.

Yeesh people, don't stick metal thingies like this in your ears! I get chills thinking about what could happen. Blergh...

ETA: https://www.amazon.com/dp/B01M3P2R19/ref=cm_sw_r_cp_apa_RiiOBbTYBGF1G

Dont have a link to the individual one i have because i picked it up at my local brick and mortar for about 3-4$. But THIS kit looks like more than enough for ~9$ on amazon. If you poke around a bit more im sure you could find an individual one.

Sounds good, per your persuasion, I've decided to get some Krytox 205/105(or104) and mix 60/40.

I plan to just mix them in a small vial and I guess I can use any syringe like this and use it to apply to my switches?

For weigh boats I use these, work perfectly. And to round out your weighing arsenal, one of these for smaller loads, and one of these for the larger ones.

Drill a hole in the base of the nose cone next to the attachment point and drizzle in epoxy to whatever weight you need. For bonus points, use a hobby syringe and your hole can be tiny (~1mm).

The particular brand BD uses is Monoject I think, in the standard 60ml. Any brand should work... just ensure that it has the correct 'tip' for tubing.

Something like this should work!

Oh wow, much different then I was expecting, you get what I was expecting; right? How sometimes the hole flares out like a single mm, so I thought it was just going inward a mm instead lol

-

The carb on this reminds me of just a regular weed pipe with not as deep of a bowl, except there doesn't appear to be a (second?) Carb (since that's almost always on the left IME), so it's obviously different in that case

-

Thanks for sharing. Yea I imagine loading this is a lot easier. I have a bunch of these lab spatulas that fit very nicely into my carbs for loading. Although my one pipe it BARELY fits into and doesnt fit into that one's stem at all, but all my other ones it has fit into either side no problem.

-

Can't imagine what a pain it'd be for most people who use a folded piece of paper to get it in. Fuck that.

For flush cutters/snippers (don't need two tools really) get either:

• https://www.amazon.com/Xcelite-170M-General-Shearcutter-Diagonal/dp/B0002BBZIS or
  
• https://www.amazon.com/Hakko-CHP-170-Micro-Cutter/dp/B00FZPDG1K
  
  Even the cheapest ESD tweezers are ok for holding components, get a kit that includes angled ones if you're going to do a bunch of SMD.
  
  These are good also: https://www.amazon.com/Hakko-3-SA-Non-Magnetic-Microelectronics-Applications/dp/B00FZPEWI6

I have this set: Bstean Syringe with Blunt Tip Needle and Cap - 10ml, 5ml, 3ml, 1ml Syringes and 14ga 16ga 18ga 20ga Blunt Needles - Great for Oil or Glue Applicator (Pack of 10) https://www.amazon.com/dp/B01HFTYINS/ref=cm_sw_r_api_9nZhAbF628E32

Used 14g blunt tips and they worked great, cheap for 100: https://www.amazon.com/gp/product/B01K1VO3E6

Mix http://www.amazon.com/gp/aw/d/B01CK32JXU/ref=mp_s_a_1_3?qid=1459371669&sr=8-3&pi=SY200_QL40&keywords=ejmix&dpPl=1&dpID=31s2734ti5L&ref=plSrch

http://www.amazon.com/gp/aw/d/B00AU6Y6C2/ref=mp_s_a_1_1?qid=1459371760&sr=8-1&pi=SX200_QL40&keywords=small+beaker&dpPl=1&dpID=31-J48-oRpL&ref=plSrch beakers for mixing and measuring and cooking

http://www.amazon.com/gp/aw/d/B00DXPRTHG/ref=mp_s_a_1_1?qid=1459371820&sr=8-1&pi=SX200_QL40&keywords=blunt+tip+syringe&dpPl=1&dpID=21SzolFINTL&ref=plSrch syringe to transfer liquid and I use mine to stir the solution while it warms up

Someone posted what I use but deleted their comment so:

​

Tweezers: https://www.amazon.ca/Hakko-3-SA-Non-Magnetic-Microelectronics-Applications/dp/B00FZPEWI6/

I use a hot air station: https://www.amazon.ca/WEP-858D-Soldering-Station-Suitable/dp/B0055B6NGE/

Pcb Holder: https://www.amazon.ca/Circuit-Holder-Adjustable-Soldering-Repairing/dp/B075DCBR24/

Microscope to find bad joints and loose solder balls: https://www.amazon.ca/Plugable-Microscope-Flexible-Observation-Magnification/dp/B00XNYXQHE/

Solder paste: https://www.digikey.ca/products/en/soldering-desoldering-rework-products/solder/262?FV=ffe00106%2C2dc186b&quantity=0&ColumnSort=-1000009&page=1&pageSize=25&pkeyword=solder+paste

I like these to clean paste or flux https://www.amazon.ca/MG-Chemicals-Tapered-Cotton-Length/dp/B008OA8488/

Conical Tip for small pin fixing https://www.mouser.ca/ProductDetail/578-ETS

Beveled tip for drag soldering if needed https://www.mouser.ca/ProductDetail/577-EW-511

ST-Link-v2 (programmer) https://www.digikey.ca/product-detail/en/stmicroelectronics/ST-LINK-V2/497-10484-ND/2214535

​

What I do is put a glob of paste on a piece of paper and dip the syringe tip lightly to make a smaller glob hang off the tip, then place the small glob from the tip on the pad I'm doing. I know this isn't the right way but its the easiest I've done.

​

When the pieces are in place I set the hot air to 450ish and lower air flow so it doesn't blow pieces off the board. When the solder solidifies most the time everything gets aligned to the pads (capacitors will randomly stick straight up but is fixed by poking it with tweezers)

​

I start with Ic's then check under the microscope for bridges or loose solder balls. then resistors/caps. Double check again for anything wrong and if its good program it with the st-link. Once thats good I put on the pots/buttons/leds

​

For faceplates, I tried at first to 3d print them. Didn't look the best, made it look cheap. So I just order faceplates when I order the pcb's now. They cost a lot but I want them to look nice when done.

After reading thru this site, here is my shopping list:

• 500ml, 100Mg/ml Supercritical Nicotine/USP PG (CXTC)
  
• Peach Colorless Flavor Concentrate by LA (4oz) (Wizard Labs)
  
• Vegetable Glycerin USP
  
• Gloves, Flasks, Syringes, Bottles
  
  Going for a 70pg/30vg blend, just need to track down a good e-juice calculator from the sidebar.

I use these. They work perfect. https://www.amazon.com/dp/B01K1VO3E6/ref=cm_sw_r_cp_apa_eK-LBbQBJZQ2C

I prefer citadel over all. I use the citadel Colour app to help with the color choice and how to apply. I do use Vallejo when I need an air brush version of a color that Citadel doesn’t have or for priming.

I understand the stance you have on the pricing with citadel, but you can make that line of paint last longer.

Head to amazon and order these items
15ml dropper bottles
1ml needless syringe
flow aid
small stainless steel ball baring

By following the steps in this video on YouTube I was able to transfer all my base and layer paints to dropper bottles. Now I can limit how much paint I’m wasting to a minimum. Because like you said, they can be expensive

If you can unscrew the atomizer on both and the funnel fits, you can pour with a steady hand. You can also use plastic pipettes; they are cheap as chips.

If the atomizers can't be removed I use these syringes and followed that video.

That oil is very viscous you won’t be pouring it anywhere. (And those carts suck IMO). To answer your question, you need some blunt tipped syringes. I found a variety pack on amazon for less than $10.

I emptied one on these apex and another similar one from theory wellness (again, bad cart) into used mostly empty ones from sage (really good cart). Works fantastic.

To reduce viscosity and make it easier to suck up with the syringe, use a hairdryer on warm to throughly heat the cart and oil.

Edit:: link
Check this out: 9 Pack - 10ml, 3ml, 1ml Syringes with 14Ga and 18Ga Blunt Tip Needl... https://www.amazon.com/dp/B01CFJ51X4/ref=cm_sw_r_sms_awdb_8drXzb76J26XX

http://www.amazon.com/turtle-icon-Oval-Sticker-CafePress/dp/B009UBWRME/ref=sr_1_10?ie=UTF8&qid=1398448318&sr=8-10&keywords=turtle+sex


http://www.amazon.com/Secure-Instant-Cosmetic-Novelty-Teeth-One/dp/B002GUIDEM/ref=sr_1_2?ie=UTF8&qid=1398448581&sr=8-2&keywords=teeth

http://www.amazon.com/Pack-Syringes-Blunt-Fill-Needles/dp/B00DXPRTHG/ref=sr_1_8?ie=UTF8&qid=1398448611&sr=8-8&keywords=syringes

http://www.amazon.com/dp/B00H5AAYHM/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&colid=3D43YIIQXSL5V&coliid=I2HWPJNVFO4RK8&psc=1

^ that last one is the one I actually want, although the syringes may come in handy sometime ;)

Really thin tweezers probably. Maybe drill a thin hole, and screw in a thin screw to pull it out. If you can't you might have to replace the jack.

Edit: Hakko CHP 3-SA Stainless Steel Non-Magnetic Precision Tweezers with Very Fine Point Tips for Microelectronics Applications, 4-3/4" Length https://www.amazon.com/dp/B00FZPEWI6/ref=cm_sw_r_cp_apa_i_-k2SCbAXPW0HV

Here are some thin tweezers lol

Here's one option - the metal tips are a lot more precise than what you find at Hobby Lobby and other craft stores (the plastic tips don't get small enough)

https://www.amazon.com/Purpose-Precision-Applicator-Assortment-Henna/dp/B01IPOJSF0

Oh, this looks even better:

https://www.amazon.com/dp/B01HFTYINS

Know how that goes, tip for ya next time (three cats here, all have needed pills at one point or another, one of them has lung nodules and needed medication for a year two pills twice a day).

Short answer, dissolve the pills in a bit of water and then use a needless syringe to squirt into back of throat. I actually think it's easier on the cat and the human vs the method shown in the image. It's also handy if you need to split tiny pills into say quarters. Dissolve pill in 4 mL of water and then just give 1mL dosage. Make sure to ask your vet if that method is OK for the pills before doing.

Things you'll need:

• Mortar and pestle. Used to crush the pill into a powder.
  
  
• syringes.
  
  Crush the pill in mortar & pestle. Dump powder into syringe tube. Fill with water and shake. Squirt into back of kitties mouth and done.
  
  Also, this is assuming there isn't a liquid version of the medicine. I always ask the vet.

I bought Duda Energy Syringepk010 Industrial Syringes with 15G x 1-1/2" Blunt Tip Fill Needle and Plastic Cover, 10 mL (Pack of 10) https://www.amazon.ca/dp/B00DXPRTHG/ref=cm_sw_r_cp_api_SyBEzbN1K6M1M off amazon for 15$.
Might be able to find cheaper for a single. But I wanted some extras.

I can't help you with the coral, but did want to offer some advice on the aiptasia. It's not necessary to remove the entire rock, I've found a really easy way to get rid of them. Get some cheap industrial syringes and boil some water. Suck up the boiling water and squirt it right on the aiptasia, close as you can. This will loosen it up (and probably kill it anyway). Then reverse the suction and draw it back up into the syringe. No chemicals, worked every time for me.

https://www.youtube.com/watch?v=y-E9nIjBoQw

Then you don't have to completely remove a perfectly good coral/rock.

I use these tweezers on my semps. It’s [a little too] satisfying.

Maybe a E-cig store. amazon hopefully linking isn’t against the rules.

This set of [syringes](http://www.BSTEAN.com/ Syringe Blunt Tip Needle and Cap - 10ml, 5ml, 3ml, 1ml Syringes 14ga 16ga 18ga 20ga Blunt Needles - Oil or Glue Applicator (Pack of 10) https://www.amazon.com/dp/B01HFTYINS/ref=cm_sw_r_cp_apa_i_SkBuDb127QQVQ) will change the game for Star San, lactic acid, etc. additions.

Having a set of cheap bar rags has incredible.

I use a cookie cooling rack on the ledge in my keezer for oint glasses so that there's airflow under them and they aren't sitting in condensation.

A 2 cup pyrex measuring cup and small whisk for everything from gelatin additions to dissolving campden additions.

Harbor Freight nitrile mechanics gloves for cleaning when things like PBW or BLC are involved. They're think and don't rip and also have longer wrists than the food service ones.

https://amzn.to/2RkC7De something like this is what I have

but if you do opt for the syringe method, i recommend this

I bought these syringe tips and they've been working well. https://www.amazon.com/gp/product/B01K1VO3E6/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

I like my lab spoon/spatula.

Sturdy, long and cheap.

http://www.amazon.com/gp/product/B0061OT1A4/ref=oh_details_o05_s00_i00?ie=UTF8&psc=1

edit: To avoid confusion. Both ends of this tool are flat. It works fine for stirring and scooping sugar or jams for example but it doesn't have a true concave spoon on it. FYI.

Just did the same thing this week! It’s been working out really well. I recommend getting some blunt tipped needles (I used these Lost ocean 100pcs Green Color Metal Blunt Tip Dispensing Needle (14G) https://www.amazon.com/dp/B01K1VO3E6/ref=cm_sw_r_cp_api_i_tb3VDb0DYTGDJ) that attach to the end for injecting the warmed up oil into the cart to minimize waste.

Use this: https://www.amazon.com/dp/B06Y2JWDQ3

Blunt syringes like the above will be cleaner, and you'll be able to get every last drop out of the bottle when near the end.

If you are just packing the capsules full of powder, you can use a capsule filling machine. I recommend the capsule machine as I've used it to pack powdered shrooms into size 00 capsule (0.5g in each).

If you are working in smaller quantities then you'll have to fill each capsule individually with a spatula. It is time consuming, but there's something tranquil about the process. I'd put some weigh paper onto your scale and add powder with the spatula to the desired weight. Fold a crease into the weigh paper beforehand so you can use the paper to slowly drop the powder into the capsule. Repeat.

I filled about 13 size 5 capsules using creased weigh paper. The capsule machine can also help with smaller quantities by holding your capsules and minimizing spillage (put some tape over the nearby holes). Unfortunately, there are no affordable size 5 capsule machines so I had to hold them very carefully.

Well, since I've never tried it, I'm not sure - you can find smaller blunt tips - here's an example:

https://www.amazon.com/dp/B01HFTYINS?psc=1

Look around a little - there's a ton of this kind of stuff.

Here's a 10 pack of 18 Gauge blunt tipped syringes for $8, Amazon primed to your door. Most vape shops will also carry them, probably for cheaper.

I got then on amazon for about $10. Here is the link:

http://www.amazon.com/gp/aw/d/B00DXPRTHG/ref=mp_s_a_1_6?qid=1421263500&sr=8-6&pi=AC_SX110_SY165_QL70

I use aiptasia-x and they work for me.

I bought my files, drill, tweezers and dykes off of Amazon and they all together set me back less then $50
each thing was 10-15
http://amzn.com/B00E8ER10G
http://amzn.com/B000OVHZ3U
http://amzn.com/B00DVIEJ14
http://amzn.com/B001N1AASC

Not to worry, they're all still waiting for their Amazon order to arrive, so they won't be needing this quite yet.

Depends on where you live. I buy mine on Amazon.

You need to buy something with a cap.

Don't use the metal needle to suck up the distillate, it is too thick and won't work. Just use the open tip and clean it off when done.

https://www.kushbottles.com/packaging-concentrate-syringes

https://www.amazon.com/Pack-Cartridges-Liquids-cigs-juice/dp/B0161V0024

https://www.amazon.com/dp/B073ZB3X8S/ref=sspa_dk_detail_6?psc=1

I bought these and they work pretty well for injecting dielectric grease into the hole in the stab that the wire goes in

https://www.amazon.com/gp/product/B01HFTYINS?psc=1

you might want to buy a blunt needle instead. I'm going to buy these:

https://www.amazon.com/Momok-Pack-juice-Liquids-cigs/dp/B072XFYXVB

You can also get plastic needles which don't look like metal needlers that are used for shots. Here is an example on Amazon. https://www.amazon.com/dp/B001QQ6MO0/ref=cm_sw_r_cp_awdb_jicCzb6Z21Y2B

Noodler's Ahab. You can use any sort of eyedropper-like tool, but I prefer a blunt-tip syringe, such as this one.

I have a few recipes I could give out, [VG and PG are on Amazon] (https://www.amazon.com/Glycerin-Vegetable-Kosher-USP-Pharmaceutical/dp/B00PSGWHIO/ref=sr_1_13_a_it?ie=UTF8&qid=1524904013&sr=8-13&keywords=vegetable+glycerine). and excigexpress is where I buy all my flavors. You also need a beaker set, .01 g scale, syringes, medical gloves, glass bottles for steeping, and plastic bottles

Edit: links

Blunt Tip Syringe

https://www.amazon.com/Bstean-Syringe-Blunt-Tip-Needle/dp/B01HFTYINS

Gemini-20 - cheap, reliable, and reads 0.001 gram increments. I also have one of these for scooping.

BSTEAN Syringe Blunt Tip Needle... https://www.amazon.com/dp/B01HFTYINS?ref=ppx_pop_mob_ap_share


this is what i bought brother

Syringe

https://smile.amazon.com/Bstean-Syringe-Blunt-Tip-Needle/dp/B01HFTYINS/ref=sr_1_4?ie=UTF8&qid=1524590844&sr=8-4&keywords=blunt+syringe&dpID=518U71I8%252BzL&preST=_SX342_QL70_&dpSrc=srch

Cheap scale that does the job.http://www.amazon.com/American-Weigh-GEMINI-20-Portable-MilliGram/dp/B0012TDNAM

Buy 00 capsules-easier to pack.
http://www.amazon.com/Now-Foods-Veg-Capsules-Capsules-250-Count/dp/B000OSQS4U

And then get a spatula if you need one to pack and so your hands don't get sticky.
http://www.amazon.com/Heathrow-Scientific-HD15909-Spatula-Overall/dp/B0061OT1A4

Search for "lab spatula" and you'll find a ton of different options. Mine looks similar to these https://www.amazon.com/dp/B075VLJQDZ/

Try a blunt-tipped syringe

this little scoopula

I found this on Amazon. It's eligible for Prime.
https://www.amazon.com/dp/B06Y2JWDQ3?psc=1

You might also try a local Vape shop. They'll probably have one they might part with.

yep


I also use one for water testing so I can suck exactly 5ml of water out of a tank for the lil test tube without contaminating the sample by sticking my hands in there.

Well... the last time that I bought cheap black Chinese ESD-safe tweezers, I received a large smelly white Chinese bathroom rug so YMMV.

I got 10ml syrynges and 3ml syrynges each for around $8, 120ml of 12mg base for $6.39, strawberry ripe and vanilla bean ice cream both for $3.95 and from TFA.

3 Pack 150ml Syringes, Large... https://www.amazon.com/dp/B07C71C1LH?ref=ppx_pop_mob_ap_share

I bought a 3 pack. One for dirty fluid. One for clean fluid. And a spare

I got these: tweezer set

I wanted non magnetic as it's a pain to pull any magnetic debris out of a motors magnets otherwise :)

I have large syringes that I use to focus water in my arrangements with different succulents in one container and found they also work well when empty to blow dirt and pooled water that could cause blemishes and rot on the leaves away. Here's the ones I ordered from Amazon.

3 Pack 150ml Syringes, Large Plastic Garden Syringe for Scientific Labs, Measuring, Watering, Refilling https://www.amazon.com/dp/B07C71C1LH/ref=cm_sw_r_cp_apa_i_lVAWCb1R5AXFE

get these, fill one with water and squirt it in a spoon with your drugs. give it a minute to dissolve and apply a little heat if you need to, then let it cool for a sec and suck it into the syringe. now you can snort this directly out of the syringe or use it to boof.

https://www.amazon.com/dp/B01N01TO2O/ref=sspa_dk_detail_0?psc=1&pd_rd_i=B01N01TO2O&pd_rd_wg=nva8v&pd_rd_r=7X6S1CWMT27FD4HS0R54&pd_rd_w=id59C

Use syringes with plastic tubing stuck on them. Just mix it up on a piece of scrap wood or paper plate, pack the syringe, and inject.

You could also use heavy duty freezer bags with a corner cut off... like piping frosting onto a cake.

blunt tip needles are cheap and safer.

https://www.amazon.com/Pack-Refilling-Liquids-cigs-juice/dp/B01CFJ51X4?ref_=bl_dp_s_web_13895365011

edit: c & p fail

I got these just the other day. I diddn't need ten but you get them for less than a dollar a piece. I dont have a saltwater tank so im not sure what you are looking for, I use these for measuring and dosing fertilizers

I had a similar problem, I ended up just grabbing some of these.

A coffee straw would've been cheaper... but the syringes are handy to measure with from time to time.

https://www.amazon.com/dp/B06Y2JWDQ3/ref=sspa_mw_detail_0?psc=1

Open bore syringes are a thing my dude

Lost ocean 100pcs Green Color Metal Blunt Tip Dispensing Needle (14G)

https://www.amazon.com/dp/B01K1VO3E6/ref=cm_sw_r_cp_api_i_7QjWCbJQ962VT

Lost ocean 100pcs Green Color Metal Blunt Tip Dispensing Needle (14G) https://www.amazon.com/dp/B01K1VO3E6/ref=cm_sw_r_cp_api_i_Da2OCb005Q4BQ

Unfortunately your only option is to get a rail from a used Joy-Con. Replacement rails aren't even available in the Chinese market yet as I'm told.

Though that bent pin looks fixable. As long as you can straighten it and then pull it outward to match the other pins, it should make contact at least a little bit. I'd use precision tweezers for that.

You can also drill a tiny hole to the middle of the crack and use a blunt tip syringe (like the ones for shots but not sharp) to apply glue or epoxy.

Then remove the bolt in the joint and cut a spline slot with a circular saw in the direction in which the forces occur. Glue in a hardwood spline. replace bolt.

It's this syringe. I think the problem may be the needle-like tip so I'll check out the baby syringe.

whaaaat? thats not possible! haha, i have a pair that is really pointy, BUT, they dont "grip" and when i'm trying to pull something out, it just slips right thru... i need a pair that HOLDS! ive gotta find out what kind these are!
EDIT: adding a link - wonder if these would work?! http://www.amazon.com/Marrywindix-Tweezers-Non-magnetic-Forceps-Anti-static/dp/B00DVIEJ14/ref=sr_1_1?ie=UTF8&qid=1454113263&sr=8-1&keywords=precision+tweezer

Jenny WTF!?! BLUNTS! You want blunts! And by that I mean these blunts This way you won't stab yourself, accidentally tattoo yourself, and it's probably not going to take as long to get through customs if you can't find the equivalent on canada's amazon.

not at all
Subtotal (5 items): $46.23
and you lget mor than you'll ever need.
you can optimize it by picking smaller pack but just to give you an idea what you are in for.
get some wide mouth bottles with a scale.
edit:
oh and get a funnel for the 30ml bottles!!!

to measure your flavours
https://www.amazon.com/Pack-Refilling-Measuring-E-Liquids-Adhesives/dp/B01CFJ51X4/ref=sr_1_1?ie=UTF8&qid=1485157215&sr=8-1&keywords=syringe+set

bottle to carry your juice with you more than enough i bought ten and thats more than needed
https://www.amazon.com/Vktech-Plastic-Dropping-Bottles-30ml/dp/B00F098JJA/ref=sr_1_1_a_it?ie=UTF8&qid=1485157332&sr=8-1&keywords=30ml+bottles

for when you are to lazy to shake
https://www.amazon.com/MatchaDNA-Handheld-Milk-Frother-Silver/dp/B018TCWL8O/ref=sr_1_4?s=kitchen&ie=UTF8&qid=1485157363&sr=1-4&keywords=milk+foamer

storrage for your juices
https://www.amazon.com/Plastic-Mouth-Experiment-Bottle-Capacity/dp/B016CLEU1U/ref=sr_1_1?s=industrial&ie=UTF8&qid=1485157538&sr=1-1&keywords=bottles+100ml

storage for you base
https://www.amazon.com/Lautechco-1000ml-Plastic-Experiment-Reagent/dp/B01MEGYZGA/ref=sr_1_20?ie=UTF8&qid=1485158603&sr=8-20&keywords=1000ml+wide+mouth

Homebrew Materials:

Vacuum Pump Oil

Vacuum Tubing

1/4" Barb x 1/4" NPT Male Hose Fitting

1/4" Male x 1/4" Female NPT Extension Hose

Vacuum Pump

Filters

Spatulas

Magnetic Stir Bar

Digital Hotplate with Magnetic Stirrer

Nitrile Gloves (Better than Latex)

Empty Capsules (Buy Separated unless you hate your life)

Capsule Machine (If you value your sanity, buy more than a 100... I hated my life doing this)

Mohr Pipets

Pipette 10ml

Mortar and Pestle (If you're doing orals, get this... Otherwise, you're playing Russian Roulette with your doses and liver)

Funnel (For pouring into small places)

Alconox (For clean your shit)

Temperature Gun (How hot is my shit?)

Graduated Cylinder (If you measure with beakers, you're a fucking idiot... And you should consider Volumetric Flasks)

Beaker Set

1 Liter Beaker (Because brewing en'masse is better)

Scale (I have a 2kg one, too)

Calibration Weight Set

Calibration Weight 100g (Because you need two for the scale linked)

Vacuum Regulator (Unless you want to filter 9001 times due to broken shit)

Oil (Any USP grade, filtered or unfitlered)

BB

BA

Butyl Stoppers

Flip Top Seals

Crimper

Vials (Unsealed)

Autoclave (Cheaper than an oven, why are you using an oven?!)

Weight Boats (Buy a million of these. They're cheap and useful)

Did I miss something? Probably. Yes.