Reddit mentions of Custom Accessories 92529 Smoke Flat License Plate Cover

So it is actually a 3 part ordeal.

The actual fog lights since my car didn't come with them, and the stalk. Then I did some c-shaped drl since I have leds in my high beams and the factory drl doesn't work with leds, but then the c-shaped drl didn't work for a little bit so I bought the drl turn signals, and then the previous c-shaped ones started working again. I will just post all of my mods below:

Fog lamps with brackets : https://www.amazon.com/dp/B01FL8DPWU?ref=ppx_pop_mob_ap_share

Light stalk : https://www.amazon.com/dp/B00AWO7XOK?ref=ppx_pop_mob_ap_share

C-shaped DRL : https://www.amazon.com/dp/B014P7LPEI?ref=ppx_pop_mob_ap_share

Sequential LED Turn signals with DRL : https://s.click.aliexpress.com/e/5veD22k

9005 LED High Beam : https://www.amazon.com/dp/B075J9S4DT?ref=ppx_pop_mob_ap_share

H11 55W HID Low Beam : https://www.amazon.com/dp/B07CMKT2F4?ref=ppx_pop_mob_ap_share

7440 7443 LED Brake/Tail Light : https://www.amazon.com/dp/B07GTKLF32?ref=ppx_pop_mob_ap_share

7440 LED Turn Signal (rear) : https://www.amazon.com/dp/B07Q8RZRZV?ref=ppx_pop_mob_ap_share

194 LED License plate/used as side markers in the front/a couple other places : https://www.amazon.com/dp/B07BT23WVC?ref=ppx_pop_mob_ap_share

194 LED side marker bulbs (not used but the correct ones if you want yellow, I liked the white and it was what I had when the originals burnt out but didn't ever change them from the above link) : https://www.amazon.com/dp/B01KY7GCXW?ref=ppx_pop_mob_ap_share

License plate smoke : https://www.amazon.com/dp/B007LICQ9M?ref=ppx_pop_mob_ap_share

Grille : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F254096211721

K&N 33-2480 Air Filter : https://www.amazon.com/dp/B00CR9WVPE/ref=cm_sw_r_cp_api_i_VfS6CbNBD59AQ

I had my rims done by a local company, they are the factory 16" painted gloss black. My mazda emblem is actually a long story, but essentially it is just scuffed up with sand paper ready to be painted but I liked the look and stuck it back on the way it is. I have also installed car play, and 3D printed a shift knob. The factory bose system was a little lacking and put a small under seat sub in to help fill the sound, but am still not happy with it, so that's a future project.

Some near future plans for the car include the aero kit, and I'll post the links to those here too:

Front Bumper Lip Air Dam : https://www.amazon.com/dp/B01FTUE8EY/ref=cm_sw_r_cp_api_i_bdS6Cb2X8Y22M

Black Mirror caps : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F283050942561

Side skirts : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F391544070112

And the rear diffuser : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F113007041503