Reddit mentions of IRWIN Tools Marples Woodworking Chisel Set, 4-Piece (M444S4N)

Here are the basics, I will edit if I think of any more essential tools, but you can go an awfully long way with these.

Hand Tools:

• Hand saw- I prefer Japanese style pull saws, meaning they cut on the pull stroke. My go to utility saw is a Vaughn bear saw, which is a robust package, with several types of interchangeable blades. There are countless types of saws, for different uses, but a fine toothed Japanese saw will get you by for most things.
  
  
• Combination square- A sliding ruler square, perfect for marking and layout. you will also want a speed square eventually, so you might as well get one.
  
  
• Tape measure- Start with a basic 25' tape, and get more as needed.
  
  
• Basic chisel set- Most of the entry grade chisels are pretty much the same, this Irwin set is a pretty good buy. to start with a set of 1/4", 1/2", and 1" are all you really need, but you can never have enough chisels.
  
  
• Block plane- A low angle block plane will get you a long ways breaking corners and trimming pieces. Stanley makes a great, affordable, option. As time goes by you will need a jack plane, but a block plane will do for now.
  
  
• Sharpening equipment- A fine diamond stone like this will get you a long way keeping your chisels and plane sharp. You should do research into sharpening methods as you use your tools more, and build a system that fits you.
  
  
• Hammer- A cheap smooth face hammer. Build a wooden mallet as a starter project.
  
  
• Clamps- You always need more clamps. Big clamps. Small clamps. Weird clamps. I like bar clamps. Harbour Freight has good deals on fair clamps, but don't expect too much out of them. To start with get a couple with ~8" throat, and a couple with ~18" throat.
  
  Power Tools:
  
  
• Cordless drill- If you're willing to spend the money for a good, reliable, tool I recommend Makita, but a Ryobi or Rigid will serve you well if you're just working on small projects. Everyone has their favourite cordless tool brand, and, for the most part, it really is just preference. I highly recommend adding an impact driver and circular saw to whichever system you choose.
  
  
• Circular Saw- If you want to work with plywood or larger sticks, you will want a circular saw, which is the most basic power saw. Most of the major tool companies make fine starter saws, Skil is the original, and is quite cheap, but there are plenty of others, browse a store and see what takes your fancy.
  
  
• Jig saw- A jig saw is used for cutting curves, and you will eventually need it if you build enough things. I prefer Bosch but there are cheaper options. See what feels right to you.
  
  
• Miter saw- You don't need this right away, but if you start doing more projects you will want one. I recommend going right to a sliding compound miter saw, like this Dewalt. You will never need more miter saw than that, and if you get a small one you will eventually end up buying a the real deal.
  
  
• Table saw- Again, you don't need this right away, but eventually you will feel you need the precision and ease that a table saw brings. The Rigid portable table saw is a great saw if you're working in tight quarters and need to pack up, but you'll appreciate the appreciate the stability of a cast iron topped cabinet saw if you have the cash and space for it.
  
  Misc:
  
  
• Drill bits- Get a cheap twist drill set that goes from 1/16" to 1/2" and a basic spade bit set. Later you will want a set of forstners and hole saws.
  
  
• Utility knife
  
  
• Driver bits
  

Stanley has made some pretty good planes. I'd suggest you try and find a vintage one in decent condition (you can even get some off ebay reasonably) and tune it up. Hone the base and sides, clean off any rust, take it all apart and get the sawdust out (especially from the mating surfaces for the frog), soak the screws in some solvent and clean em off, hone the iron cap so it lies flat, sharpen and hone the blade (or buy a good replacement if it needs it [Lee Valley/Veritas has good ones]).

Theres lots of good brands for chisels, I would honestly not mess about with trying to get vintage ones; just buy a set of Marples for now, or look at some of the fancier offerings from Lee Valley.

Veritas is considered one of the best values in hand saws, but they are expensive for a beginner. Unfortunately I don't know about saws well enough to recommend a less expensive brand. Unless you know or want to learn how to sharpen a saw, I'd stay away from vintage ones.

Of course, you MUST sharpen these for them to work best. I personally use these everyday!
http://smile.amazon.com/Crown-187-8-Inch-203-mm-Gents/dp/B001V9KOFA/ref=sr_1_1?ie=UTF8&qid=1407863136&sr=8-1&keywords=crown+saw
http://smile.amazon.com/Irwin-Industrial-Tools-M444-S4N/dp/B000RFX032/ref=sr_1_1?ie=UTF8&qid=1407863154&sr=8-1&keywords=irwin+chisel
will post more if I think of them