#8 in Extension cords
Use arrows to jump to the previous/next product
Reddit mentions of LEDENET 22AWG 5pin 33FT 10m Extension Cable Line for 5 Color RGBW LED Strip Lights Wire 3528 5050
Sentiment score: 2
Reddit mentions: 4
We found 4 Reddit mentions of LEDENET 22AWG 5pin 33FT 10m Extension Cable Line for 5 Color RGBW LED Strip Lights Wire 3528 5050. Here are the top ones.
or
- For SMD5050 RGBW RGBWW led strip light
- 5 pin cable wire line core. White Bule Red Green Black 5 stand wire.
- 22 AWG 5pin wire
- Package included: 10 meters RGBW cable
- If you need L shap solderless connector for 12mm RGBW strip, you can use our 12mm wide L shape connector (ASIN: B014IJ7HX6)
Features:
Specs:
| Color | Colorful |
| Size | 33 Feet |
If you don't mind going the DIY route, you could probably come in under $100 for parts for the strips:
Instead of the flat channel, you might be better off with angled channel for mounting the strips above the cabinets, since they'll throw more light on the wall, which is what you'll actually see - https://www.amazon.com/LEDwholesalers-Aluminum-Mounting-Installations-1901-V/dp/B00PJSSD7K/
There's a ZWave RGBW controller but it's more expensive than the wifi one and can take some more configuration: https://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW/
If you get the snap-on connectors, I recommend putting a small amount of solder on all of the pads where you'll be connecting them on the strips, so that they make a good connection.
As for the puck lights, you could probably get something like this and wire the distributor to the wifi/ZWave controller, instead of plugging it into the controller it comes with: https://www.amazon.com/Changing-Christmas-Furniture-Ambiance-Lighting/dp/B01N2I47VH/ref=sr_1_2
Not really familiar with the van in question but are there any interior lights at the moment? You could always take off whatever covers the current light and hook up the LED strip to that. Very recently I hooked up few sections of an LED strip to my Camry by using the dome light circuit and took apart some of the interiors to route the wires around the car. I ended up putting light strips on the footwells of the front and rear seats, the dome light was replaced with some LEDs and there was a strip along the rear windshield. I used a 5050 LED strip and ~50ft of wires.It seems light the tools you have would already work, you would just need to find a circuit to connect to.
Here's what I used to do my kitchen. Works with Hue can be cut to length and comes out nice and clean. Did do some soldering but you can probably get away not having to. I used 1 ballast and ran a wire thru the attic instead of using 2 ballasts but that was just to save on cost.
https://www.amazon.com/gp/product/B00NMSQ4QQ/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B01MZ6CB2D/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B01MU76VMY/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B072JKPLQW/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B00K6ZJVP4/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B016XJS5B2/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B00J4HI746/ref=oh_aui_detailpage_o05_s01?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B00ML3Q2ME/ref=oh_aui_detailpage_o05_s02?ie=UTF8&psc=1
Would it be as simple as I get this extension then just strip the end of the wires and split it in something like these connectors or would it not hold the wires in it?