#2,091 in Industrial & Scientific
Use arrows to jump to the previous/next product
Reddit mentions of Sunhokey 12V 40W Cartridge Heater and NTC Thermistor 100K 3950 Compatible with 3D Printer Creality CR-10S Pro, CR-X, Ender 3, Ender 3 Pro, Prusa Mendel(Pack of 12pcs) (Red-12V 40W)
Sentiment score: 1
Reddit mentions: 1
We found 1 Reddit mentions of Sunhokey 12V 40W Cartridge Heater and NTC Thermistor 100K 3950 Compatible with 3D Printer Creality CR-10S Pro, CR-X, Ender 3, Ender 3 Pro, Prusa Mendel(Pack of 12pcs) (Red-12V 40W). Here are the top ones.
or
- Cartridge Heater Material : 304 stainless steel ,the core is made of Nickel-chromium alloy.
- Parameters：12V 40W, 6*20MM(Lead length 1M)
- Thermistor :Temperature sensor 100KΩ accuracy of ± 1%
- Features：High sensitivity, rapid response,easy installation, wide temperature range, good stability, high reliability.
- Customer Service：If you receive any damaged or not working products, please contact us, you will be free to renew.
Features:
Specs:
| Color | Red-12V 40W |
| Weight | 4.52 ounces |
Man, thank you for helping me so so very much. I will begin by trying to help you answer anything you ask as best I can. From what I recall considering this thing is now over two weeks old and I've done like of stuff to it yet still having no luck (yet moving forward) I can say that the person I bought it from had apparently thought it was a thermistor issue as the old one was still on but in bad shape. So I tested it with the wires still attached and I thought it read pretty good like close to the 100k ohms I'm looking for on my other printers thermistor.
The one I put in it is one of the 100k ohm-er's I was speaking of and as far as I can tell it very likely is the cause of this 700° BS that is going on now...
Everything should be hooked up right as I went and double checked that as soon as I encountered.this issue after replacing the thermistor.
Here is the screw in thermistor I haven't tried yet:
[Gulfcoast Robotics] Thermistor Upgrade for Maker Select Plus and Wanhao Duplicator i3 Plus 3D Printers. https://www.amazon.com/dp/B07B3ZYBTM/ref=cm_sw_r_cp_apa_i_SHqyCbFDJB3A5
This is an Amazon link to the thermistors and heaters for the hotend that I've put into it since getting it:
Sunhokey 12V 40W Cartridge Heater and NTC Thermistor 100K 3950 for 3D Printer(Pack of 12pcs) https://www.amazon.com/dp/B07KXSFSKP/ref=cm_sw_r_cp_apap_kiwvfNkNbZTWP
And it looks like the E3D V6 hotend that I think comes stock on the makerfarm Pegasus 10 models.
And this all being said and what you have already mentioned it is highly likely that I need new thermistors? I did go to the site that sells these and the heater I put on it at least claims all the same specs. 12v 40 watt heater... So I felt better after reading that considering I had already put it on this machine...
You are a terrific person for reaching out to me about this I've had a few folks reach out and I'm still dealing with these issues some of them the same ones. I don't expect there to be a ton of folks out there that are expert enough to just take on this sort of thing site unseen so I will do my best to accommodate you in any way that may help me gonna go post links to some pics of I can....