#3 in Automotive electrical connectors
Use arrows to jump to the previous/next product
Reddit mentions of YETOR 16 AWG Way Car Waterproof Electrical Connector,4 pin Plug Auto Electrical Wire Connectors Marine for Car, Truck, Boat, and Other Wire Connections.(5 Pack)
Sentiment score: 1
Reddit mentions: 1
We found 1 Reddit mentions of YETOR 16 AWG Way Car Waterproof Electrical Connector,4 pin Plug Auto Electrical Wire Connectors Marine for Car, Truck, Boat, and Other Wire Connections.(5 Pack). Here are the top ones.
or
Specification:4 pin male & female waterproof connectors with 16AWG 10cm wire.Operating temperature : -10℃~+80℃.Easy to Use:Easy to install under soldering and crimping.Wide Range of Application:Use for car, truck, boat, motorcycle, and other wire connections.Package includes: 5setsx 4Pin waterproof connector with cable(Each set include:1 x 4way Male Connector with 10cm wire;1 x 4way Female Connector with 10cm wire)
Specs:
| Height | 0.5 Inches |
| Length | 2.4 Inches |
| Size | 4pin connector--5pack |
| Width | 1 Inches |
C Light - https://www.diodedynamics.com/2015-2019-subaru-wrx-sti-c-light-switchback-led-halos.html
Halos - https://www.diodedynamics.com/hd-led-halos-for-2015-2019-subaru-wrx-wrx-sti-pair.html
Blinker Module - https://www.diodedynamics.com/led-flasher-for-2015-2019-subaru-wrx.html (Needed this because I removed my stock blinker lights. Could have wired in resistors, but this was easy and cheap)
LED Conversion Bulbs - https://www.diodedynamics.com/low-beam-led-headlight-for-2015-2019-subaru-wrx.html (Still waiting on these, so haven't tested them, but they'll be in this Friday)
Headlight Sealant - https://www.amazon.com/RetroRubber-Grade-Butyl-Headlight-Sealant/dp/B01N5PM29J
Harnesses to clean up wiring - https://www.amazon.com/gp/product/B07QFW8X9Z/ref=ppx_yo_dt_b_asin_image_o00_s00?ie=UTF8&psc=1 (Haven't installed yet, but planning on tomorrow)
Used to seal the hole of the old C Light bulb. Ran the C Light and Halo Harness through here - https://www.homedepot.com/p/Permatex-3-oz-Black-Silicone-Adhesive-Sealant-75150/302775053
Used to hold Halo in - https://www.homedepot.com/p/J-B-Weld-0-47-oz-ClearWeld-50114H/303710929 (There's other ways to do this, but this is what I chose)
Paint I used - https://www.homedepot.com/p/Rust-Oleum-Painter-s-Touch-2X-15-oz-Flat-Black-General-Purpose-Spray-Paint-25-Bonus-336099/304221900
I also got the Subispeed harnesses, but I didn't use them because I deleted the stock turn signal bulb.
​
And I think that's it. Be sure to wear nitrile gloves too to avoid finger prints.
​
Also take your time. Don't paint the high beam housing unless you have another plan for those like a second projector.
​
Any other questions or pictures let me know.
​
(Side note, this is probably not done for me and I'll probably post more if I do more with these. Thinking about changing the bumper cover holes where the turn signals were for instance)