#5,951 in Sports & Outdoors
Reddit mentions of Umbrella Corporation AeroShell 33MS / 64 Gun Grease .5oz / Mil-Spec for Barrel Nut Thread
Sentiment score: 1
Reddit mentions: 5
We found 5 Reddit mentions of Umbrella Corporation AeroShell 33MS / 64 Gun Grease .5oz / Mil-Spec for Barrel Nut Thread. Here are the top ones.
Buying options
View on Amazon.comor
- MIL-G-21164D for upper receiver threads, barrel nut installation and buffer tube installation
- High quality lube good for any number of applications, exercise equipment, hinges, reels, ball bearings, bicycle gears, even telescope mounts
- Aeroshell 64 / Aeroshell 33 MS sets the standard with exceptional anti-corrosion and anti-wear performance
- Our portable .88oz jar (.5oz grease) container makes for easy application of this AR grease with just the tip of your pinky finger
- Made to perform under extreme pressure and heat to prevent damage.
Features:
Specs:
Weight | 0.02 Pounds |
How many builds have you done, sir? With the Grease/Loc-tite combo? Grease I bought was this:
https://www.amazon.com/gp/product/B01GGQMF54/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Umbrella Corporation AeroShell 33MS / 64 Gun Grease .5oz / Mil-Spec for Barrel Nut Thread https://www.amazon.com/dp/B01GGQMF54/ref=cm_sw_r_cp_api_i_pm-KDbXFD5DP1
Everyone swears by it, I use it too and it’s worked well. Not sure if there is a cheaper equivalent but like u/cakan4444 said, it will do several builds just applying to the barrel extension
Edit and threads of barrel nut.
Here is what you need
​
They have prime 1 day for free.. This is what I use. mil spec.. it will last forever.. If your gonna build something build it right IMHO
​
Have fun building.. you will never buy a complete gun again
Make sure to use Aeroshell 33ms on the barrel (1/2oz is enough for about a dozen builds)... Some build videos say to use anti-seize, which is usually copper and/or graphite based and a big no-no because it could cause galvanic corrosion. Do you have a vice and workbench? This upper and lower block set was cheap and worked fine for me. You'll need an armorer's wrench... Don't go $5 cheap, but there's no reason to buy a $50 one.
They make a proper tool for doing the pins in the trigger guard instead of using pliers.
https://www.brownells.com/gunsmith-tools-supplies/general-gunsmith-tools/punches/ar-15-trigger-guard-roll-pin-pusher-prod55709.aspx
https://www.amazon.com/Wheeler-Trigger-Guard-Install-Tool/dp/B01B3NW460/ref=sr_1_2?ie=UTF8&qid=1524371192&sr=8-2&keywords=ar+trigger+guard+install+tool
I have the top one. I just put some electrical tape on the side that makes contact with the lower to help prevent any scratching. The tool isn't needed but it can really help for installing and removing them.
Another optional tool:
https://www.brownells.com/gunsmith-tools-supplies/rifle-tools/staking-tools/ar-15-m16-sling-swivel-staking-tool-prod40894.aspx
For staking the sling swivel mount to a fsb.
Edit: Don't forget the grease that one should install on the barrel threads to make it so you can remove it later without a fight. AeroShell 33MS is the mil-spec stuff.
https://www.amazon.com/UCWRG-AeroShell-33MS-Grease-5oz/dp/B01GGQMF54/ref=sr_1_1?ie=UTF8&qid=1524371444&sr=8-1&keywords=barrel+grease+ar+15