Reddit mentions: The best car distribution fuses
We found 3 Reddit comments discussing the best car distribution fuses. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 3 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Jex Electronics 4-Way Car Audio Stereo Amp Power/Ground Cable Splitter Distribution Block 4ga
- 4-Way Power Distribution
- Solid Copper Construction
- Input 1X 4AWG
- Output 4X 8AWG
- Course threaded gold plated grub screws to solidly secure wires
Features:
Specs:
Height | 0.98425 Inches |
Length | 2.95275 Inches |
Weight | 0.2 Pounds |
Width | 0.90551 Inches |
2. KnuKonceptz Bassik 2 Way Mini ANL Fuse Distribution Block - 1/0 Gauge to 4 Gauge - 150 Amp
- Compact 2 Way fuse block with fuses
- Accepts 0 or 4 gauge Input. Two fused 4 or 8 gauge outputs
- Uses set screws to secure the wire, no adapters required
- Works as a power block, ground blocks also available.
Features:
Specs:
Height | 1.2 Inches |
Length | 2.36 Inches |
Size | 150 Amp |
Weight | 0.25 Pounds |
Width | 1.75 Inches |
3. LEIGESAUDIO Copper 0/4 Gauge to 4/8 Gauge 80 Amp Mini ANL 3 Way Fuse Holder Distribution Block
- Solid Brass,High Performance Copper Car Audio Power Fuse Distribution Block
- 0/4 Gauge In To 4/8 Gauge out
- Compact 3 Way Fuse Block With Mini ANL Fuses
- The Interior Is Made Of Copper, And The Cover Is Made Of High Strength, Nonperishable Industrial-grade Plastic
- Applicable to auto, boat or other vehicles, protect your audio system.
Features:
Specs:
Height | 1.18 Inches |
Length | 3.66 Inches |
Size | 80Amp |
Weight | 0.75 Pounds |
Width | 2.42 Inches |
🎓 Reddit experts on car distribution fuses
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where car distribution fuses are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
Pioneer HU seems feasible, but a better model with more features is suggested. I run a Pioneer Excelon double DIN model, and the variable HP & LP slopes & frequencies, along with the 13 band EQ are quite handy. I'd suggest looking for these features for tuning the SQ in your rig, unless you plan on doing some sort of DSP upgrade too.
For the sub, Fi is a good brand, as long as your box is well designed. I'd assume you'll get the 2 ohm model.
The sub amp seems like a good price, tho I can't speak for the Hifonics brand, it is listed in the recommended components. The Brutus model is good for a 2 ohm sub.
I'd suggest an 0/1 wiring kit. I found this 0/1 bundle with a quick search, I'd suggest looking for something similar. For an extra $20 you can buy a crimping tool so get hammering (heh). An 0/1 is enough to split to your sub amp and what I hope will be an amp for your components (more later on that). You'll want an 0/1 to 4 awg distribution block, and some extra 4 awg to run to your amps. You can feed & ground your amps with 4awg (or 8awg for a smaller stereo amp) once you deliver the power to the distributor block via 0/1. You can also ground in reverse with another block, running 4awg (or 8awg) grounds to the 2nd distributor, and then 0/1 to a ground point.
Speakers are good choices, with the 2ohm Polk MM series another possible good choice.
As for modeling the sub, make sure to build the port large enough to keep down port velocity, and factor the size of the port into the total box volume. Make sure the box is 1.5ft^3 net volume, with the total volume being 1.5ft^3 + the port volume.
No amp is listed for the components, so I'd suggest something with at least 120 watts/ch, as erring on the side of extra power helps cut out distortion & clipping. A 4channel with sufficient build in crossovers could allow you to run an "active" setup, but you'd need a high/low pass feature that extends to ~4khz for the xover. You'd also need to high pass the components altogether, which makes the HU's HP & LP features important.
LOC $130
Front Speakers verify fitment. $150
Amp Kit for RF amp $30
Amp Kit for JL $50
Distribution Block $15
$375 total.
No worries. Here are a few amazon specials. They should do the trick. Most decent car stereo shops will also have a selection.
3 fuse block