Reddit mentions: The best hardware nails
We found 15 Reddit comments discussing the best hardware nails. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 15 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Tremont Nail CLR6V - Standard Steel Clinch-Rosehead Square Nails 5lb Box of 2" (6d)
- Solid Steel Construction
- Heavy-Duty Thickness
- Loosening is Reduced Compared with Modern Nails
- Great for Historic Renovation and Preservation
- Made In The USA
Features:
2. OOK by Hillman 533704
- Brass Plated and made of Masonry
- Penetrates hard wall surfaces without damaging walls
- Recommended for hanging objects on hard wall surfaces where regular nails are not adequate
- Bendless Nails WILL NOT bend
Features:
Specs:
Height | 4.752 Inches |
Length | 0.688 Inches |
Number of items | 1 |
Width | 1.93 Inches |
3. Porta-Nails 42629 2-Inch x 16-Gauge T-Head Hardwood Flooring Nails (1,000-Pack)
- 1,000 nails will fasten approximately 200 sq. ft. of 2-1/4 in. wide tongue-and-groove flooring
- Use for angle and face nailing applications without damage to the flooring
- Use for decorative paneling and ceilings and sub-flooring
- Use with the Porta-Nailer and or Portamatic flooring installation tools (sold separately)
- Cupped point to help the nail to cut through the wood and avoid splitting even with very hard species
Features:
Specs:
Color | Bright |
Height | 0.25 Inches |
Length | 2 Inches |
Number of items | 1 |
Weight | 4 Pounds |
Width | 0.03 Inches |
4. CARPET TACKS UPHOLSTERY NAILS 25 MM ( pack of 120 ) by ONESTOPDIY
- Please leave feed back as we value all our customer's comments.
- Please note all our orders are shipped within 1 working day from the United Kingdom.
- zinc plated nail
Features:
Specs:
Weight | 0.11904962148 Pounds |
5. SODIAL Spacer for screwing, for glass / mirror / nails, stainless steel, silver, 4 pieces
Product Name: spacer for screwing; Material: stainless steelColour: Silver; Hole diameter: 5 mmOverall dimensions (L x D): 2.5 x 1.6 cmNet weight: 66 g
6. 20 Pcs Stainless Steel Advertising Nails Glass Wall Connector Standoff 12mmx25mm
Specs:
Weight | 0.72 Pounds |
7. 1000 Pack Nails for DIY Shoe Repairs Heels and Segs 13mm Lengths
Ideal for attaching heels and plates to shoes13mm length1000 pcs per lot
8. decotacks Upholstery Nails Decorative Tacks 7/16" - 100 Pcs [Pewter Finish] DX0511PW
- 100 Pcs/Pack, Head Diameter (D) [7/16 in] *** Full Length top the bottom (H+L) [5/8 in] *** Shank Length under the cap to bottom (L) [1/2 in]
- Made by full automatic German machines with high quality steel and double layer electroplated Pewter finish
- Strong and heavy weight items for upholstery industry, with proper tools you will not need any prefix hole. Please don't compare this items with filmsy cheap DIY nailheads.
- Requires proper tools like Needle nose pliers and light weight tack hammers to install them. Not using pliers will cause bending. So please don't use your fingers to hold them while hammering.
- You won't be disapointed, they will always stay bright & beautiful. Please don't use any chemicals to clean nailheads, it may damage the surface finish in time, so please just clean them with dry peace of cloth.
Features:
Specs:
Height | 3.15 Inches |
Length | 3.15 Inches |
Weight | 0.20282528104 Pounds |
Width | 0.79 Inches |
9. 100Pcs Iron 0.43"x0.67" Vintage Style Flat Upholstery Nails Studs Tacks Pins for Furniture Sofa Door Decoration
- Size and quantity: 100Pcs decorative tacks, enough quantity to meet your daily need. Size: approx.11x17mm(Dia.xH)/0.43"x0.67".
- Material: Made of long lasting iron, surface plating treatment, anti-corrosion, not easy to fade.
- Vintage style: the furniture upholstery tacks are pretty and classic that will not effect the beauty of the furniture, and the vintage outward appearance can easily match the surroundings, which will make your sofa, chair, bed and so on, not only look more beautiful, but more sturdy and durable.
- Wide application: The upholstery tacks can be applied for decorations of your sofa, beds, wood crafts, walls, wooden box etc. or you can use them to fix maps, photos and other lightweight stuffs. It is suitable for office, school, home and so on.
- Easy to install: you could just clamp DIY nail with a plier, then use a light hammer to install them. But please be careful and don't put your fingers to hold them while hammering in case of injury, because they may jump or bend under improper operation.
Features:
Specs:
Height | 0.67 Inches |
Length | 0.43 Inches |
Size | Style 2 |
Weight | 93 Grams |
Width | 0.43 Inches |
10. The Hillman Group 122675
Sharp-pointed nail, with a double point,Unlimited usesThey are ideal for use in school, office and have unlimited uses around the houseModel number: 122675
Specs:
Height | 4.883 Inches |
Length | 0.94 Inches |
Number of items | 1 |
Weight | 0.02 Pounds |
Width | 1.933 Inches |
11. Tremont Nail CC6 - Standard Steel Common Square Nails 1lb Box of 2" (6d)
Solid Steel ConstructionHeavy-Duty ThicknessLoosening is Reduced Compared with Modern NailsGreat for Historic Renovation and PreservationMade In The USA
12. National Nail 135055 250CT 1-Inch Plastic Cap Nail
- Deformed ring shank for greater holding power electro galvanized to enhance corrosion resistance. Conforms to surfaces.
- All hand driven caps are packaged as integral nail-cap units Cap nails round plastic burron cap ring shank lgth 1 inch count=250.
- Flexible round head conforms to surface making it difficult for water to get under the cap. use to secure roofing felt, sheathing, building papers, etc.
- Can be used for roofing felt, sheathing, polyethylene, roll roofing, re-roofing, chicken wire, wire lathe. Flexible plastic head.
- Flexible round head conforms to surface making it difficult for water to get under the cap. Can be used for roofing felt, sheathing, polyethylene, roll roofing, re-roofing, chicken wire, wire lathe.
Features:
Specs:
Height | 4.5 Inches |
Length | 6 Inches |
Number of items | 1 |
Weight | 0.45625 Pounds |
Width | 4.5 Inches |
14. Grip Rite 112HGJST5 5 lb Hot Dipped Galvanized Joist Hanger Nails, 1-1/2"
- For attaching joist hangers to wood studs
- Short, heavy gauge nail provides increased holding power without fully penetrating wood
- Approved for exterior use with all types of treated lumber
- All Grip-Rite hot dipped galvanized fasteners meet ASTM A-153 requirements and can be used with treated lumber
Features:
Specs:
Height | 1.75 Inches |
Length | 3.5 Inches |
Number of items | 1 |
Size | 1-1/2" |
Weight | 5.15 Pounds |
Width | 4.5 Inches |
15. Grip Rite Prime Guard 8HGSPK #3/8 by 8-inch Galvanized Steel Spike Nails (50-lb Pack)
- Commonly Used To Secure Railroad Ties And Landscaping Timbers
- Used To Secure Large Members In Log Home Construction
- Resists Rust And Weathering
- Hot-Dipped Galvanized Finish
Features:
Specs:
Height | 6.5 Inches |
Length | 9.5 Inches |
Number of items | 1 |
Weight | 52 Pounds |
Width | 9.5 Inches |
🎓 Reddit experts on hardware nails
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where hardware nails are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
I would say embrace the project. This is what a 200 year old pine floor is supposed to look like:
https://enterprisewood.com/reclaimed_floor_opt/reclaimed-pine/
If it works with your aesthetic, rough-hewn plank floors look awesome. As the poster above suggested, square head nails would look right at home face nailed into these planks. You can even lightly hand scrape the edges for a nice break between boards. Plus, since pine is so soft, *WHEN* it gets scraped or dented, those marks will just add to the "character" of the floor. Bonus: you don't need to worry about the stain going on evenly.
17.38. YES. WHO DOESN'T LIKE DOGS.
Don't glue it down. Absolutely no need for glue.
Use an underlayment of tar paper 15# or 30# doesn't matter or get an underlayment made for wood floor installation. I can't remember what it's called but it is like butcher paper.
Use nails to attach. Get a flooring nailer, either manual or pneumatic doesn't matter. I prefer manual nailers. It is easier to feel when the nail is completely set in the tongue of the board. Use a nail set to drive any that don't set completely after a couple of whacks. Don't buy the Porta-Nailer nail set tool. It tends to be smaller than the nail head and slips off easily.
Porta-Nailer - Manual
Porta-Nailer - Pneumatic
Nails for Porta-Nailer
Lots of different brands of flooring nailers
Hardwood flooring underlayment
No need to get too elaborate with the underlayment. It serves as a vapor barrier and dust barrier so nothing infiltrates from below the subfloor and it prevents squeaking floor boards assuming your boards are properly nailed.
Don't glue any of this down. At all. Don't use glue.
Good luck.
I came here for the cost as well. I didn't see it, so here is my best assumption, assuming everything was purchased for the cheapest price possible.
48 square feet of cheap carpeting: $24
4'x8' piece of cheap plywood: $13.95
6 wooden circles from Hobby Lobby at 79 cents each: $4.74
Smallest container of carpet glue: $5.47
Small bottle of Gorilla Glue: $4.97
Small package of carpet tacks: $4.15
--------------------------------
Minimum cost to build OP's cat tree: $57.28
Professionally made cat tree of similar stature: $56.99
Seems about right.
Yes ! J'ai fini par trouver en cherchant dans "clous" -_- : https://www.amazon.fr/Espaceurs-visser-SODIAL-espaceurs-inoxydable-4-pi%C3%A8ces/dp/B01CTXWXVE/ref=sr_1_4?s=hi&ie=UTF8&qid=1493898665&sr=1-4&keywords=fixation
 
Merci !
Standoff mounts
The exposed disks will be visible, but you want that space behind in whatever way you mount it.
With a pack of 10 you could to 3 mounts top and bottom (horizontal center and ~600mm to each side) and 2 mounts on each side edge (~300mm above and below the vertical center.)
Isnt it likely that's just lack of experience? Its not some super special skill imo.
I spent some time repairing shoes and a tack hammer has a tiny head and the nail you use on certain heels or heel protectors is pretty small
these small bastards
I'd be surprised to find that a person could not become reasonably comfortable with it in a few hours and would not have trouble hitting a nail twice with reasonable force.
IMO This is not a surprising result after 200 houses. His accuracy probably stagnated fairly quickly (what do you learn from driving the 9,888th nail that you didn't already learn? Diminishing returns.
I'm not saying this is easy, just that they are not the michel jordan of hammering :D
It's definitely a tack hammer. Not sure of the brand. You see these a lot in furniture repair shops. They're light weight and are used to drive small tacks to hold down the upholstery. Modern versions have a split magnetic end to hold tacks in place before hammering.
Um. Those would be push pins. These are thumb tacks.
i know it's technically breaking form, but along your sentiment, could we perhaps use iron brads intended for antique furniture?
https://www.amazon.com/100Pcs-Vintage-Upholstery-Furniture-Decoration/dp/B07B8ZXMC5?psc=1&SubscriptionId=AKIAILSHYYTFIVPWUY6Q&tag=duckduckgo-brave-20&linkCode=xm2&camp=2025&creative=165953&creativeASIN=B07B8ZXMC5
It's a square cut nail, it may by old, but they still make these, this one looks modern (within last 50 years) and not antique.
just lay some plywood over the holes (under the tarp). it's a flat roof so there is going to be puddling on the tarp no matter what.
cover the whole with plywood and any other weak spots they might fall through. then cover the flat roof with the tarp, butt it up to the walls of the house with 2x4's. leave about a 12-16 inches on the wall-side of the 2x4 to tack up against the house.
in your second picture i cn see the siding and it looks like you might be able to tuck that flap of the tarp up under that bottom row of siding. this way the rain will run down the wall and right onto the tarp instead of down between the wall and 2x4.
to seam two tarps just overlap them about 12 inches and tack it down every 12 inches of so with cap nails
if the seam is on a incline make sure to tuck the lower tarp under the higher top on the incline.
search square cut nails. amazon has them for $10ish/lb 1lb=60 mails ish bet you can find em cheaper
I’d hanger that.
Get a palm nailer: Hitachi NH90AB Mini Impact Palm Nailer, 360 Degree Swivel Fitting, Accepts 2-1/2" to 3-1/2" Bulk Framing Nail, 5 Year Warranty https://www.amazon.com/dp/B01NBJZ6RE/ref=cm_sw_r_cp_api_Tqx-BbQYQY36Y
And a bunch of these: https://www.strongtie.com/facemounthangersssl_solidsawnlumberconnector/luc-lu-u-hu-huc_productgroup_wcc/p/luc.lu.u.hu.huc
And a bunch of these: Grip Rite 112HGJST5 5 lb Hot Dipped Galvanized Joist Hanger Nails, 1-1/2" https://www.amazon.com/dp/B000B4KZOQ/ref=cm_sw_r_cp_api_Nsx-BbVVSHC9C
And get nailin!
Then insulate that bad boy.
I have a set of three SOG throwing knives from when I was starting out that still work just fine for me.
But I've found recently that the cheapest option is to just go to a hardware store and buy some landscaping spikes. Just sharpen them up.
They're so cheap it doesn't matter if you damage them or lose one.
You can even buy 52 pounds of them on amazon!
http://www.amazon.com/PrimeSource-3Gs-8HGSPK-Landscape-Spike/dp/B000BD6ELU/ref=sr_1_48?s=lawn-garden&ie=UTF8&qid=1404879152&sr=1-48&keywords=landscaping+spikes