Reddit mentions of Chemical Guys HEX_3KIT_5 5.5" Buffing Pad Sampler Kit, 4 Items - (1) 16 oz Polishing Pad Cleaner + (3) 5.5" Buffing Pads that Work with 5" Backing Plates

Here’s a straightforward shopping list and beginners guide. This will knock out most if not all of your swirl marks.

Shopping List:

Machine Polisher - PORTER-CABLE Variable Speed Polisher, 6-Inch (7424XP) https://www.amazon.com/dp/B002654I46/ref=cm_sw_r_cp_api_i_l7SADbKPP1Q6Q

Backing Pad - Astro 4607 5" PU Velcro Backing Pad https://www.amazon.com/dp/B003CH3Z8W/ref=cm_sw_r_cp_api_i_T7SADbZ187WK1

Buffing Pads - Chemical Guys HEX_3KIT_5 5.5" Buffing Pad Sampler Kit (4 Items), 16. Fluid_Ounces, 4 Pack https://www.amazon.com/dp/B01J588UNG/ref=cm_sw_r_cp_api_i_d9SADb8WF470V

Compound - Meguiar's G17220 Ultimate Compound, 20 oz https://www.amazon.com/dp/B06W5HCZ9M/ref=cm_sw_r_cp_api_i_M9SADb0ADEMZJ

Finishing Polish - Meguiar's M20532 Mirror Glaze Ultra Finishing Polish, 32 Fluid Ounces, 1 Pack https://www.amazon.com/dp/B001O7PNXC/ref=cm_sw_r_cp_api_i_i-SADbWXADMQT

Wax - Your preference


Here’s the guide:

1 – Tool Prep

Set aside the dual-action polisher, backing pad, and foam pads. Remove the included backing plate that’s already attached to the Porter Cable polisher, use the included wrench. Re-attached using the Astro pad, secure tightly.

2 – Wash

Wash your car by hand, preferably using the two-bucket method. Afterward, move the car into your garage or shaded area. You’ll want to be out of direct sunlight, keeping the paint as cool as possible.

3 – Clay Bar

Clay bar the entire car. Make sure to wipe down the finish afterward, keeping it as clean as possible.

4 – Compound Buffing

Grab your machine polisher, the Ultimate Compound, and the orange pad. Attach the pad to the polisher using the velcro backing, make sure it’s centered. Prime the pad by dabbing 8-10 dime-sized amounts across the surface. Start working one section at a time, around 2 x 2 feet. Before you turn on the polisher, press the pad against the paint. Compound polish should be soaked within the pad, along with the paint. Press the pad against the surface, set to speed setting 2-3, and begin spreading the compound around in quick passes. Then, turn it up to 5-6 and let the fun begin. Use overlapping, slow passes. Once you’re done, wide the area clean with a microfiber towel.

5 – Inspection

Check out your results of the first section. Go over the area again if most of the swirl marks aren’t gone. If the swirls are gone, but a light haze is present, don’t worry. The finishing polish will take care of it.

6 – Polish Buffing

Use the M205 Finishing Polish with the white pad. Follow the same steps from before. Prime the pad and rub it against the paint before turning on the polisher. Use a max speed of 3-4 with medium pressure. The Finishing Polish will take care of the rest of the haze and micro scratches. Once you’re finished with the first section, wipe clean.

7 – Inspection

Again, check out the results of the M205 Finishing Polish. It’s doubtful you’ll need more than one application, but double-check all the same. If it’s looking great, move on and finish the rest of your car.

8 – Wax

Your paint is looking great. The swirl marks are gone, leaving a bright clean finish. Apply the wax using the black foam pad. Use very light pressure, letting the pad float along with the paint. You’re just coating your car’s finish, that’s all. Wipe clean with a microfiber towel.

Is this what you purchased? How many did you get? What polishes did you use?