Reddit mentions: The best photoelectric sensors
We found 5 Reddit comments discussing the best photoelectric sensors. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 2 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. DAOKI 5PCS TCRT5000 Infrared Reflective Sensor Module IR Barrier Line Track Photoelectric Switch
- Using infrared reflective sensor TCRT5000.
- Detection of reflection distance: 1 mm to 25 mm.
- The comparator output signal clean, good waveform, driving ability, more than 15mA.
- With a multi-turn precision potentiometer adjustable sensitivity adjustment.
- The working voltage of 3.3V - 5V.
Features:
Specs:
Weight | 0.01 Pounds |
2. Gowoops 10 PCS of Digital Light Intensity Detection Photosensitive Sensor Module for Arduino UNO
- 1. Using the sensitive type photosensitive resistance sensor
- 2. The comparator output signal clean waveform is good, driving ability, than 15mA.
- 3. With adjustable potentiometer can adjust the brightness of the light detected
- 4. Working voltage 3.3V-5V, the output format: Digital switching output (0 and 1)
- 5. With bolt holes for easy installation, a small board PCB size: 3.2cm x 1.4cm, using a wide voltage LM393 comparator
Features:
🎓 Reddit experts on photoelectric sensors
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where photoelectric sensors are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
H-Bridge (for the UNO there are also shields)
Sensors e.g. this / that though you can also get tctr5000 modules for cents elsewhere.
And note that if you are not set on a line-follower, the kit you've chosen already includes the ultrasonic distance sensor which is nie for robotic projects as well :-)
Do you have a soldering iron and multimeter? Even a cheap $4 multimeter is fine for low-current & low-voltage tasks, and makes your life easier (checking voltages, connections, resistor values...)
As for a soldering iron, even a $1 will do (if it doesn't burn down your house ;-) ) - but an adjustable temperature one will be more worthwhile. Even a $20 soldering station will do to get started if you don't want to spend $80-$100. I tried to avoid soldering for years, and it was a big mistake. It's actually easy and useful.
And another note: The 2wd and 4wd chars will not always go in a straight line. Motors don't run 100% in sync, even at the same voltage.
With a rotary encoder you can ajust the speed in software. You can use one of those IR reflective sensors modules, or a gap sensor, or even a hall sensor... example
You can also get 2wd kits example, but overall, they aren't as great of a value (and as you can see, they just include the standard modules)
A "sensor shield" like in that kit is nice though as it reduces the wiring chaos a bit :-) They cost $1 for the UNO at Aliexpress, probably more expensive at Amazon.
> might they be moving too quickly for a break beam IR or photoresistor?
A photocell will respond plenty fast. To get the Arduino to respond quickly enough use a digital photocell or obstacle detector module connected to interrupt-on-change pins, either on Arduino pins directly or via an IO expander like the PCF8575.
I found this 10 pack of light sensors on Amazon: https://www.amazon.com/Gowoops-Digital-Intensity-Detection-Photosensitive/dp/B01N1FKS4L/ref=sr_1_3?keywords=arduino+light+sensor&qid=1565710705&s=gateway&sr=8-3
Let's say I got these and attached them to each LED on the speaker splitter. Would I be able to attach 8 of them (mute LED and 7 zone LEDs) to the same microcontroller?