#4,151 in Audio & video accessories
Reddit mentions of Glarks 1180 Pieces 2.54mm 2/3/4/5/6/7/8/9 Pin Housing Adapter Cable Connector Socket Male and Female with 2.54mm Female Pin Header Connector Perfectly Compatible with JST-XHP Connector Kit
Sentiment score: 1
Reddit mentions: 3
We found 3 Reddit mentions of Glarks 1180 Pieces 2.54mm 2/3/4/5/6/7/8/9 Pin Housing Adapter Cable Connector Socket Male and Female with 2.54mm Female Pin Header Connector Perfectly Compatible with JST-XHP Connector Kit. Here are the top ones.
or
- Product Type: High quality male and female housing and 2.54mm female pin header connector compatible with jst-xhp connector Kit
- Material: Nylon housing, Copper pin header
- Package: This set include male and female housing each 20pcs total 320pcs, with 2.54mm female pin header which are 860pcs, stored in a transparent plastic box
- Feature: This set of connector is easy to install, Just put the crimps in the tool and press them, make the crimp the insulation are all the way toward the wire
- Widely Application: widely used for speakers, monitors, household appliances, LED lighting, copiers, FAX machines, medical equipment, computers, electronic toys, batteries, circuit boards
Features:
Specs:
| Color | JST-XHP 2 3 4 5 6 7 8 9 |
| Weight | 0.82 Pounds |
That cable should not have signs of heating, the amount of current is very low....but it looks like you must have a bad connection that is causing a high resistance and heating.... you need to get a new cable end and crimp it on....
You can dig around and find a competed cable on amazon, but it is handy to be able to extend or replace cables at times... these are links for the proper connector and crimp tool... the outermost jaw is for the jst-xh...the inner jaws will do dupont connectors which are also commonly used.
https://smile.amazon.com/gp/product/B01N1RFZZ4
https://smile.amazon.com/gp/product/B07CTH46S7
JST connectors.
This is what I bought....
Glarks 1180 Pieces 2.54mm 2/3/4/5/6/7/8/9 Pin Housing Adapter Cable Connector Socket Male and Female with 2.54mm Female Pin Header Connector Perfectly Compatible with JST-XHP Connector Kit https://www.amazon.com/dp/B07CTH46S7/ref=cm_sw_r_cp_apa_i_PaA3DbZ33G8MT
When I was asking about this for the ender 3 /u/robbob2112b gave a very detailed breakdown on what they had done.
> These are what I use on the tevo and when I put the e3dv6 on the ender I'll use them there too....
>I started them about 6 inches back up the wires from the hot end spaced them out so them aren't one big blob.... used different ones for different things so they can't be switched out and if for some reason a wire pulls loose it doesnt short anything... doing it I can swap out the hot end in minutes, do a PID tune and I'm off to the races.
>Connectors and max current rating
>Jst-sm for the fans and thermistor - 3amp
>https://smile.amazon.com/gp/product/B07CTKD7P4/
>Mini Tamiya type b for the heater - 10 amp
>https://smile.amazon.com/gp/product/B06XSD9JJQ/
>Jst-xhp are the white connector for stepper motors - 3 amp
>https://smile.amazon.com/gp/product/B07CTH46S7/
>Dupont for the black on the main board - 3 amp
>https://smile.amazon.com/gp/product/B07CVYPDGS/
>These for heated bed - up to 30 amps - solder only, not crimp
>https://smile.amazon.com/gp/product/B07H54LZN2/
>Crimpers - get the right ones for the pin type in the connectors you buy, you can't use just any old crimper or wing it with these tiny pins and get a good connection that doesn't come apart when things move for hours
>https://smile.amazon.com/gp/product/B01N1RFZZ4/
>https://smile.amazon.com/gp/product/B00YGLKBSK/
>https://smile.amazon.com/gp/product/B00OMM4YUY/
>Since I'm on the subject heated bed wires - large enough to carry the current and with the silicone cover and fine internal strands flexible enough to not break with movement
>https://smile.amazon.com/gp/product/B01M9IXL5Q/r