Reddit mentions of Lyman Universal Case Prep Accessory Set

So this review on Amazon is what my buying guide will consist of. My apologies for formatting, I am on mobile.

-----
I'm new to reloading, but I shoot a lot so instead of doing what every beginner should and buy a single stage press I saved up a little and got the AP press due to the fact I knew I would use it a lot. But after it came I quickly realized it was far more technical than I expected. I found out there were a lot of parts I still needed and a lot more money that still needed to be spent. I was fine with it bet I knew I would have to save up for a little bit to get it all. But after about 100 hours of reloading YouTube videos and four months I was able to actually start reloading. Wishing I had a guide right off the bat to tell me what I need and why I ended up making one for any other new beginner. So here it is.


Disclaimer: Do not follow my advice blindly, do your research on each piece of equipment. The prices I have stated are not set in stone, they were what I spent. I would advise you to shop around to get the best deals
--------------------------------------------------
What you still need:

--Hornady Lock N Load Auto-Progressive Reloading Press
http://www.amazon.com/gp/product/B000PD01NS/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
$462.64
Notes: Does not have to be this press

--Hornady Lock N Load Ap & Projector Shell Plate
http://www.hornady.com/store/Choose-Shell-Plate-by-Number/
$41.33
Notes: Each shell plate is for a different caliber, when you buy make sure you get the correct plate for the caliber you are reloading. Here is the guide http://www.hornady.com/assets/files/shell_holder.pdf

--Hornady Shell Holder
http://www.hornady.com/store/Choose-Shell-Holder-by-Number/
$5.00
Notes: Each shell holder is for a different caliber, when you buy make sure you get the correct holder for the caliber you are reloading. Although RCBS makes a similar looking holder, it will NOT fit in the Hornady setup. Here is the guide http://www.hornady.com/assets/files/shell_holder.pdf

--Reloading Dies
http://www.amazon.com/gp/product/B000PD6PO2/ref=oh_details_o06_s00_i00?ie=UTF8&psc=1
$43.89
Notes: All reloading dies from all companies are universal to each other's presses. So you don't have to stick to Hornadys dies (I do because I like them)

--Digital Scale
http://www.amazon.com/gp/product/B002BDOHNA/ref=oh_details_o08_s00_i00?ie=UTF8&psc=1
$29.14
Notes: Digital scales are a little more expensive bet worth it for the time you save

--Digital Caliper
http://www.amazon.com/gp/product/B0002JFMIO/ref=oh_details_o09_s00_i00?ie=UTF8&psc=1
$10.60
Notes: Digital calipers are convenient for speed but if money is tight you can go traditional

--Hornady One Shot Gun Cleaner & Dry Lube
http://www.amazon.com/Hornady-Shot-Cleaner-DynaGlide-Aerosol/dp/B000LC9YM2/ref=sr_1_1?s=sporting-goods&ie=UTF8&qid=1375560230&sr=1-1&keywords=hornady+gun+cleaner
$13.28
Notes: Used when you put the press together and clean all the parts

--Hornady One Shot Spray Case Lube
http://www.amazon.com/Hornady-Shot-Spray-DynaGlide-Aerosol/dp/B0001NA29U/ref=sr_1_1?s=sporting-goods&ie=UTF8&qid=1375560743&sr=1-1&keywords=hornady+case+lube
$13.44
Notes: This or any case lube is an absolute need or your rounds will get stuck in the die. This one is cool because you don't have to wipe it off after you deprime and resize so if you have an AP bench like mine you can just keep going.

--Case Trimmer
http://www.amazon.com/Hornady-50140-Camlock-Case-Trimmer/dp/B000PD6QJ6/ref=sr_1_7?s=sporting-goods&ie=UTF8&qid=1375561942&sr=1-7&keywords=case+trimmer
$88.99
Notes: This will trim the case down to size. Needed because after firing the case expands

--Cartridge Reloading Guide
http://www.amazon.com/Hornady-Edition-Handbook-Cartridge-Reloading/dp/B00A95QWGM/ref=sr_1_2?ie=UTF8&qid=1375563579&sr=8-2&keywords=Reloading+guide
$39.80
Notes: Tells you the specifics of each round. There is a different manual for each projectile. So if you use Hornady bullets you will use their guide, RCBS you you'd use theirs, etc.
----------------------------------------------------
What you need to clean the brass:

--Case Tumbler
http://www.amazon.com/Hornady-Case-Tumbler-110-Volt/dp/B000PD1XE4/ref=sr_1_17?s=sporting-goods&ie=UTF8&qid=1375559938&sr=1-17&keywords=media+tumbler
$83.58
Used to remove the carbon from the rounds. I advise not to deprime before use because the media will get stuck in the primer hole.

--Tumbling Media
http://www.amazon.com/Frankford-Arsenal-287178-Brass-Cleaning/dp/B001GX8DS6/ref=sr_1_4?s=sporting-goods&ie=UTF8&qid=1375561385&sr=1-4&keywords=tumbling+media
$20.10
The corn cob media is a little more fine grain and less likely to get stuck

--Metal Polish
http://www.amazon.com/Hornady-9993-Case-Polish/dp/B002L9D8VQ/ref=sr_1_1?s=sporting-goods&ie=UTF8&qid=1375561809&sr=1-1&keywords=hornady+metal+polish
$14.17
You would put this in the tumbler with the rounds to give them a nice polish
--------------------------------------------------------------
What I would recommend:

--Bullet Puller
http://www.amazon.com/gp/product/B001B7ZB4Q/ref=oh_details_o08_s00_i01?ie=UTF8&psc=1
$17.15
Used when you mess up a round, it pulls the projectile out

--Primer Turning Plate
http://www.amazon.com/gp/product/B001OPL80Q/ref=oh_details_o09_s00_i00?ie=UTF8&psc=1
$17.56
used to make sure the primers are set the right way before you put them in the primer tube

--Universal Ammo Reloading Tray
http://www.amazon.com/Hornady-1536-480040-Universal-Loading/dp/B000GU8WU4/ref=sr_1_fkmr2_3?ie=UTF8&qid=1375559333&sr=8-3-fkmr2&keywords=universal+ammo+reloading+tray
$11.38
Used to hold your rounds for inspection, and helps with precision loading powder

--Case Prep Tool
http://www.amazon.com/Lyman-Universal-Case-Prep-Accessory/dp/B0034LAVUG/ref=sr_1_2?s=sporting-goods&ie=UTF8&qid=1375562159&sr=1-2&keywords=case+prep+tool
$55.79
This is used after depriming and trimming to make sure all the holes are clean and free of debris

--Stuck Case Remover
http://www.amazon.com/gp/product/B004Y6ZJQ6/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
$18.99
Used in case you get a round stuck in the die

--Hornady Micrometer Rifle Lock N Load Powder Measure
http://www.amazon.com/gp/product/B003O1WOJ2/ref=oh_details_o01_s00_i01?ie=UTF8&psc=1
$27.99
Used to better measure out the powder in the Hornady Powder Drop for rifle calibers

--Hornady Micrometer Pistol Lock N Load Powder Measure
http://www.amazon.com/gp/product/B001OPR300/ref=oh_details_o01_s00_i02?ie=UTF8&psc=1
$39.89
Used to better measure out the powder in the Hornady Powder Drop for pistol calibers

--Powder Cop
http://www.amazon.com/gp/product/B003D6ZLXE/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
$30.57
Used to make sure you don't put more powder in than you should

--Hornady Lock N Load Die Bushing 10 Pack
http://www.amazon.com/Hornady-Lock-Load-Bushing-Pack/dp/B00162OLTW/ref=sr_1_1?ie=UTF8&qid=1375563887&sr=8-1&keywords=Hornady+AP+die+bushing
$42.22
Would recommend if you are reloading multiple calibers, it makes change over much faster.
---------------------------------------------------

What you need for precision loading:

--Hornady Lock N Load Ammo Concentricity Gauge
http://www.amazon.com/gp/product/B001KZ3NNK/ref=oh_details_o07_s00_i00?ie=UTF8&psc=1
$99.99
Only needed for precision reloading

--Powder Funnel
http://www.amazon.com/gp/product/B000PD1XI0/ref=oh_details_o07_s00_i01?ie=UTF8&psc=1
$5.78
Used for more of an exact measurement

--Hornady Microjust Seating Stem
http://www.amazon.com/gp/product/B000GU9VU4/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
$24.99
Used to get an exact seating depth with the projectile
-----------------------------
I hope this helps! I will be making some tutorial videos soon and will post a link here.

I use this: https://www.amazon.com/dp/B0034LAVUG/ref=cm_sw_r_cp_awdb_TvuUzb634F88G

It comes with both large and small primer cleaners as well as uniformers.