Reddit mentions: The best led segment dispalys
We found 51 Reddit comments discussing the best led segment dispalys. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 7 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. FIBARO RGBW Controller Z-Wave LED Strips Regulator, FGRGBWM-441, doesn't work with HomeKit
- Controlled by Z-Wave controllers such as Fibaro Home Center, Vera & URC (Smarthings, Nexia & Indigo support coming soon)
- Most advanced device of its type in the world, scene capable and can control up to 4 LED strips
- Current and historical power consumption measurements.
- Microprocessor controlled.
- 12V/24V DC Power Supply (Not Included) - Output power: 12A Total (sum of all connected outputs) Max load 12W-144W, 24V-288W combined
Features:
Specs:
Color | Rgb (Red, Green, Blue) |
Height | 0.6 Inches |
Length | 1.6 Inches |
Weight | 0.13 Pounds |
Width | 1.5 Inches |
2. uxcell 10Pcs Common Cathode 10 Pin 1 Bit 0.5" Red LED Display Digital Tube
- Product Name : LED Digital Tube;Model : 5101;Working voltage : DC 1.8-2V
- Current : <=20mA;Type : Common Cathode;Emitted Color : Red
- Pin Number : 10;Pin Pitch : 2mm/0.08";Size(No INclude Pin) : 19 x 13 x 7mm/0.7" x 0.5" x 0.3" (L*W*H)
- Digital Tube Height : 12.7mm/0.5";Material : Plastic, Metal;Color : Black, White
- Net Weight : 23g;Package Content : 10 x LED Digital Tube
Features:
Specs:
Size | 10 Piece |
3. Enclosed Switching Constant Current Mode LED Driver Current Adjust by Internal Pot, 57 to 114 Volt 2800mA 319 Watt
Primary Output Voltage (VDC): 57-114Output Current (Amps): 2. 8Maximum Output Power (Watts): 319. 2Input Voltage (VAC): 90 to 305Input Frequency (Hz): 47 to 63
Specs:
Color | White |
Height | 9.92124 Inches |
Length | 3.5433 Inches |
Number of items | 1 |
Weight | 4.1446905256 Pounds |
Width | 1.724406 Inches |
4. White LED Backlight Module - Large 45mm x 86mm
- Each LED is encased in a 3.5mm thick strip of a acrylic
- Provides near-uniform lighting
- Gels can be used to change the color
- Large Size - 45mm x 86mm lit area
Features:
Specs:
Color | White |
Number of items | 1 |
5. HiLetgo TM1638 8 Bits Digital LED Tube Display Module with 8 LEDs 8 Button keys for AVR Arduino ARM
- TM1638 is a LED (light-emitting diode display) driver control circuit with a keyboard scan interface, the internal set Into a MCU digital interface, data latch, LED high-voltage driver, keyboard scanning circuit.
- Power CMOS process;Display mode 10 segments × 8 digits;Key scan (8 × 3bit).
- Brightness adjustment circuit (adjustable duty cycle 8);Serial Interface (CLK, STB, DIO).
- Oscillation method: RC oscillation (450KHz + 5%);Built-in power-on reset circuit;Available in SOP28 package.
- Mainly used in refrigerators, air conditioners, home theater products such as high-segment display driver.
Features:
Specs:
Color | Blue |
Size | Small |
6. HiLetgo 2pcs 0.36" 4-Digit Tube LED Segment Display Module Red Common Anode TM1637 Drive Chip Tube Clock Display for Arduino UNO R3
- 4 M2 screw holes for easy installation.
- 4-digit LED display module with LED brightness adjustable and clock point.
- Display device is a total of 4 red LED word tube. Digital tube 8 grayscale adjustable.
- The driver IC is TM1637, only two signal lines can make MCU control four Digit 8-segment LED. Can be used to display decimal, letters and so on.
- Control interface: a total of 4 pins (GND, VCC, DIO, CLK), GND to ground, VCC for the power supply, DIO for the data input and output pins, CLK for the clock signal pin.
Features:
Specs:
Color | Red |
Height | 0.94488 Inches |
Length | 1.65354 Inches |
Number of items | 1 |
Size | Small |
Weight | 0.0220462262 Pounds |
Width | 0.47244 Inches |
7. EIZO CG277-BK ColorEdge Professional Color Graphics Monitor 27.0" Black
- Wide-Gamut LED IPS display with built in color calibration sensor for professional photography, design, print and post production.
- 27", 2560x1440 (16:9), 300 cd/m2 Brightness, 1000:1 Contrast Ratio, 99% Adobe RGB Coverage, 6 ms Response Time, DVI-D, DisplayPort, HDMI
- Five-year warranty and built to last and remain color accurate.
- 24/7 Tech Support Desk in North America
Features:
Specs:
Color | Black |
Height | 14.15 Inches |
Length | 28.85 Inches |
Number of items | 1 |
Weight | 19.4 Pounds |
Width | 24 Inches |
🎓 Reddit experts on led segment dispalys
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where led segment dispalys are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
Sorry if there are formatting errors and such I am on mobile.
Basics
You should really consider a better HUB/products if you want this level of automation. You are going to want an offline hub such as Vera or Homeseer (what I use). Homeseer I know will interface with the echo Vera should. Hubs like wink/SmartThings end up not working when...
Similarly, you should NOT get a nest (or EcoBee). I have a nest and while I love the design it is fickle. I would instead recommend a z-wave thermostat. With a z-wave thermostat you can do almost everything nest can (no auto scheduling).Already Purchased&nbsp;
You should seriously consider a different HUB
Dimmers and Wall Switches
Here is a good place to start. Lutron dimmers are fantastics although they can be a bit pricy (I don't think you mentioned a budget...). Other options include the GE 12724 for dimming if you want to go z-wave over Lutron. And, the GE 12722 for regular on/off. Or Homeseer is releasing new switches soon that look fantastic (Also z-wave)!
Here's some more info. 1 2 3 4
Garage Opener
Chamberlain is great!
Security
If you cannot change/return your system that fine but I would recommend a DSC power series system as they almost universally integrate with automation systems Homeseer has a plugin as does Vera.
Audio
Sonos is fine. It can be controlled via Homeseer/Vera (Think announcements). Or you can get an Echo Dot and connect it to the sonos connect via an audio cable. GET a WHA controller (Check the Outdoor speaker section for recommendations)
Front Door Cam/Doorbell
Either Doorbird a doorbell and camera (expensive) or a normal doorbell with an IP camera with motion record. The integrated solution is better but of course more expensive. If you end up with IP cameras you should consider Hikvison they seem to make the best cameras for the money.
Outdoor Light
Just install the smart switch of your choice.
Fan's
Not sure sorry. :-( GE has a fan controlling switch but I doubt it would work as you mention remotes...
Under Cabinet Lighting
Hue lightstips, Aeon lightstrips or a WIFI / Z-wave LED controller with regular strips. (Will edit later with links)
Outdoor Speakers
The Daytons are fine you could also go with Yamaha NS-AW150. For integration you could connect them to the MONOPRICE 6 Zone Controller and AMP. You could also connect the Sonos CONNECT to the monopice and have outdoor audio + sonos audio and send audio to any other zones you have!
&nbsp;
PM me or comment if you need any more info :-)
&nbsp;
*Will edit and add more info when I get to a keyboard.
Ahhh, well since you give me a great link to the molding side of it, maybe I can help you on the controller side.
Fibaro RGBW Micro Controller Z-wave, Works with RGB/RGBW LED Strips
Now, I know what you'll think, because I thought it too - $70 for a dinky Z-Wave LED light controller? WTF?!
But it's actually so much more. Besides DC in (BTW, it takes 12 or 24volts, too) & Ground there's "IN1", "IN2", "IN3", "IN4", "R", "G", "B", "W". And the manual is odd too. You connect the LEDs up, then you have to wire switches into it too, etc etc - I haven't totally figured it out, but it's kinda neat. Also you can get it running on SmartThings. I've just migrated from ST to Home Assistant with a Aeotec Z-Wave stick and a deConz Zigbee stick.
The 4 "IN"s can be used for multiple sensors - which I might have to give a shot.
Anyway, what I've done is hookup 2 light strips to the controller - one is RGB, the other cold white (It's what I have at hand, and I like the color reproduction etc etc, haven't played with many RGBW lights). I typically use a white LED strip with 60 LEDs/meter, and then the RGB is 120 LEDs/meter.
You can control almost an unlimited number of strips with the one Fibaro controller - the secret is to add in RGB LED Amplifiers when the colors start going wonky. Honestly, they're cheap enough I do it between every set of LEDs I intend to connect together.
In testing, I found I like the look for the RGB LEDs closer to the wall, and then the White strip.
So there you go - hope I didn't confuse you there, trying to bang this out and get back to running ethernet throughout the house. Let me know if you have any questions.
I have about 4 different locations with these LED strip lighting. I use Cat 6 cable to do the runs. For example many of my LED strips are RGBW so you need 5 wires to make them work. Well cat 6 or even 5 as you know has 8 wires nice solid core stuff that is easy to solder. I've even contemplated using a patch panel as a DC distribution point and using RJ connector but have not done that yet since I'm pretty much done adding LEDs. BTW old desktop power supplies make great 12 volt power sources. As a controllers I use this with my Veralite system.
I'd run some 12 volt tot he kitchen for sure for under cabinet lights. Stair ways are also a nice touch
I use one of these for the LED's behind my TV.
https://www.amazon.com/dp/B00P1N68FW/ref=sr_ph_1?ie=UTF8&amp;qid=1495035763&amp;sr=sr-1&amp;keywords=fibaro
connects to smart things, can be auotmated.
I haven't had the greatest success though in controlling it via voice (i use echo).
For some reason when i try to rename the device in smart things, it no longer connects.
However having it part of a 'routine' works very well.
Turn on/off at certain times or as part of a macro like "good night" or what not.
If you don't mind going the DIY route, you could probably come in under $100 for parts for the strips:
Instead of the flat channel, you might be better off with angled channel for mounting the strips above the cabinets, since they'll throw more light on the wall, which is what you'll actually see - https://www.amazon.com/LEDwholesalers-Aluminum-Mounting-Installations-1901-V/dp/B00PJSSD7K/
There's a ZWave RGBW controller but it's more expensive than the wifi one and can take some more configuration: https://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW/
If you get the snap-on connectors, I recommend putting a small amount of solder on all of the pads where you'll be connecting them on the strips, so that they make a good connection.
As for the puck lights, you could probably get something like this and wire the distributor to the wifi/ZWave controller, instead of plugging it into the controller it comes with: https://www.amazon.com/Changing-Christmas-Furniture-Ambiance-Lighting/dp/B01N2I47VH/ref=sr_1_2
Here are some cheap 7 segment displays. The wiring is pretty simple, just connect one of the pins on the 7 segment display to ground. The pin is usually marked with a white dot. Then connect an IO pin to each of the other pins and setting the arduino pin high will turn the corresponding segment of the display to light up. You will probably need a Mega for all the pins. Then create functions in the code which set certain pins high and others low to form letters. Then use the delay(1000); command to time things. It sounds complicated in words but its actually an easy thing to do hands on. Once you get the wiring done, if you tell me the pins, I might even be able to write all the code for you, then you could just copy it into your Arduino. Hope this helped!
I'm using cheap LED strips off of Amazon.
I have one strip controlled by a Fibaro RGBW controller.
The others are controlled by Raspberry Pis, with custom scripts to handle fades, strobes, etc.
They are very bright when it's dark out. We could see them very clearly from about 2/10ths of a mile away. I have one setting that looks like strobes from a police car. I haven't tested that one outside yet though. The plan is to use it if someone comes around licking door handles.
The picture I posted is from the blue being set at 100%.
Oh, and a video of police mode inside.
This is pretty much the best option for LED strips. You can set up 4 different sets from this one z-wave device.
https://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW
I agree with everyone else, any speakers you want and connect it to the dot. what kind of light strip do you have? Or are you looking for one? Amazon has the Sylvania one on sale right now.
https://smile.amazon.com/SYLVANIA-ZigBee-Starter-SmartThings-Assistant/dp/B00R1PB80I?sa-no-redirect=1
Great thing is you can buy a cheap Chinese Led strip to extend it for cheap, just make sure it's a 5 pin strip.
If you are looking for a zwave controller I would go with the Fibraro micro controller:
https://smile.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW?sa-no-redirect=1
Of course you would then need a hub. I personally use smartthings but if you are more technically inclined and want everything to stay local you can use it with HASS, you'll just need to pick up a zwave/zigbee stick.
Thank you so much! This is very useful information. My plan was to use one of the following 2 z-wave controllers, but whether I can use 1 or if I"ll need more will depend on the actual power requirements of these strips.
Fibaro
Qubino
I'm going to email the seller to see if they can clarify the power information.
edit: The seller responded and they said 85 watts is correct. Ultimately doesn't matter since I overlooked the fact that they are not outdoor rated! Any recommendation for quality affordable strip lights? I'm looking at something like this now.
LEDENET RGBW
I don't know of any "smart" controller that can handle more than one run of RGBW(W). The Fibaro can handle two separate runs of white (for a max of four strips without a booster), controlled through the color channels. So, having three runs would be three controllers. Although that would allow the three runs to be controlled independently, it would be with the price tag of three controllers (and the effort of setting them up). And those controllers would still need power, so it's the same thing in terms of wiring.
If there's a controller that can support multiple strips as separate "devices", I'd be very interested.
2 boards one 320 driver or 4 an 2....
4 boards one 600 driver, shop around for better prices. I've been buyin the “A” series drivers as they all put out more then the “B” series
https://horticulturelightinggroup.com/products/qb288-v1-slate-2-single-combo
.
Check this out at Amazon.com
[PowerNex] Mean Well HLG-320H-C2800A 114V 2800mA 319.2W Single Output Switching LED Power Supply with PFC https://www.amazon.com/dp/B01LVTRN6S/ref=cm_sw_r_other_apa_i_2kcCCb26MN94K
.
Check this out at Amazon.com
[PowerNex] Mean Well HLG-600H-54A 54V 11.2A 604.8W Single Output Switching LED Power Supply with PFC https://www.amazon.com/dp/B019RNT1L4/ref=cm_sw_r_other_apa_i_FocCCb1TFPY0M
Did you know Amazon will donate a portion of every purchase if you shop by going to smile.amazon.com instead? Over $50,000,000 has been raised for charity - all you need to do is change the URL!
Here are your smile-ified links:
https://smile.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW/ref=sr_1_1
---
Never forget to smile again | ^^i'm ^^a ^^friendly&nbsp;bot
I spent a little time looking into lighting one room in my house solely with LED strips last year. I was primarily looking at cheap, 5-meter strips on Amazon, and thinking of controlling them with something like Fibaro's Zwave controller. Some things might have changed in the last year, but probably not much:
LED strips (generally) aren't as efficient as LED bulbs. It's hard to pin down numbers on this, and I may be wrong, but that's the impression I got after a lot of reading.
Low-voltage DC wiring over long distances has significant problems: Voltage drop and current limits are a function of the length and diameter of the wire, respectively. A 3 volt drop is insignificant for 120V AC power, but is 25% of 12V system. Power (watts, which will correspond to lumens) is a function of voltage and current. If you reduce the voltage by a factor of 10 (120 to 12) you lose 90% of the power you can shove through a given wire. You can compensate by using thicker diameter wire (expensive) or running higher voltage DC power (24 or even 48 volt).
You already touched on the price and length issue: With LED strips, you generally determine the length of the strip by the length of the wall or ceiling you want to run the strip along (even if a meter of LED strip provides enough light for the room, you don't want a single meter of LED strip in the center of the ceiling - that would just look weird).
I do have some LED strips in my house - they're fantastic for above and below cabinets, and I also have a couple strips above my workbench - it's almost impossible to cast a shadow on my workbench now.
Edit: I forgot to mention Wife-Approval-Factor - my wife absolutely refused to have "exposed" LED strips anywhere in the main living areas. And she has a point - they're not the most aesthetically-pleasing light sources. That limits you to indirect lighting (which you already specified) and means fewer lumens go to lighting the whole room, and you have to figure out tasteful way to hide the strips.
Anyway, that's my ramble on LED strips. Hopefully some part of it was useful.
Good luck with your new house!
You could look at something like this
https://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW/ref=sr_1_1?ie=UTF8&amp;qid=1503774345&amp;sr=8-1&amp;keywords=zwave+led
or
i have several of these in the office they work well
https://www.amazon.com/gp/product/B00MGTVORQ/ref=oh_aui_detailpage_o01_s00?ie=UTF8&amp;psc=1
I just bought one of these: https://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW
Really pleased with it so far.
I don't know anything about the LIFX, but if you have (or plan on getting) a zwave controller, I'd go with the Fibaro LED Controller. With that, you could easily use any led strip you wanted.
I use a Fibaro RGBW microcontroller to control mine (under cabinets). It can be added to a simple momentary switch in the wall as well so you get the benefit of controlling it via a wall switch, and/or through your home automation system (it's a z-wave device so it works with both devices you named). The micro controller is a bit more expensive, but then you can spend a lot less on the actual RGBW strips.
https://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW/ref=sr_1_1?ie=UTF8&amp;qid=1479334032&amp;sr=8-1&amp;keywords=zwave+rgbw
How about an EL panel like this
Qubino makes one, as well as Fibaro
Aliexpress links are hidden automatically, but this is the same thing on Amazon.
https://www.amazon.com/HiLetgo-Digital-TM1638-Display-Arduino/dp/B01D140BT6/ref=sr_1_1?ie=UTF8&amp;qid=1502941165&amp;sr=8-1&amp;keywords=tm1638
Specifically, for North Americans.
https://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW
http://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW/ref=sr_1_1?ie=UTF8&amp;qid=1452027496&amp;sr=8-1&amp;keywords=led+zwave+controller
https://www.amazon.com/dp/B00P1N68FW/
Check this guy out.
https://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW
https://www.amazon.com/Fibaro-Micro-Controller-Z-wave-Strips/dp/B00P1N68FW
https://www.amazon.com/HiLetgo-Digital-Segment-Display-Arduino/dp/B01DKISMXK/
What voltage do they need. 12 volt maybe 24 volt.
MY guess is you could hack in one of these
Firago..Fibrago? Has a Zwave controller for RGB(W?)
Edit: Fibaro!
I think he may be referring to this one... Fibaro RGBW Controller
LEDs were from https://www.ledworldlighting.com. Any controller would work, but the Z-wave I used is the Fibaro. http://www.amazon.com/gp/aw/d/B00P1N68FW/ref=mp_s_a_1_1?qid=1451773341&amp;sr=8-1&amp;pi=SX200_QL40&amp;keywords=fibaro+rgbw&amp;dpPl=1&amp;dpID=41tT0RMfMlL&amp;ref=plSrch.
Sorry for the long links I'm on mobile.
Other Z-Wave LED strip controllers include Fibaro Qubino RGBGenie.
I didn't realize the Hue line included LED strips. I apologize for any confusion.
[So something like is for amateurs?]
(https://www.amazon.co.uk/dp/B00GJ5DB9M/ref=cm_sw_r_cp_apa_i_rYUmDbB0G9XFB)
I think you're talking crap. Those monitors you're on about are specialised for cinema.
I'm on about consumer monitors. Even so, the one I've showed you is just shy of £2k.
Or are you telling me I should ditch my IPS because a 240hz GAMING VA panel would be better? I highly doubt it.
Source: I do it for a living.
PS: Do you have a link for the Fibaro dimmers? I'm looking but don't seem to see them, only a black box - no switch.
Hallelujah - I'm stoked on that RGBW light controller. Wish it was cheaper than that but that controller + 32 feet of light strip is still cheaper than 6ft of Phillips FOH strip.
Edit: I ordered a RGBW controller - I'll update when I receive/install it. (Wed 19th)
Edit 2: I don't like that your charge more for Amazon :( I understand it costs you more but I still don't like it.