#16 in RC vehicle parts
Use arrows to jump to the previous/next product
Reddit mentions of Flysky FS-i6X 10CH 2.4GHz AFHDS RC Transmitter w/ FS-iA6B Receiver
Sentiment score: 4
Reddit mentions: 5
We found 5 Reddit mentions of Flysky FS-i6X 10CH 2.4GHz AFHDS RC Transmitter w/ FS-iA6B Receiver. Here are the top ones.
or
Offering superior protection against interference while maintaining lower power consumption and high reliable receiver senstivity.Bidirectional Communication Capable of sending and receiving data, each transmitter is capable of receiving data from temperature, altitude and many other types of sensors, servo calibration and i-BUS Support.Each transmitter and receiver has it's own unique ID. Once the transmitter and receiver have been paired, they will only communicate with each other, preventing other systems accidentally connecting to or interfering with the systems operation.The high efficiency Omni-directional high gain antenna cuts down o interference, while using less power and maintaining a strong reliable connection.The system is built using highly sensitive low power consumption components, maintaining high receiver sensitivity, while consuming as little as one tenth the power of a standard FM system, dramatically extending battery life.
Specs:
| Height | 4.33 Inches |
| Length | 9.45 Inches |
| Width | 8.27 Inches |
I appreciate the effort. This seems promising and may be the better idea, the other route I was going to take was the Bardwell kit with some other stuff.
https://store.rotorriot.com/bardwells-budget-build-kit/
https://www.racedayquads.com/products/rdq-series-1300mah-4s-100c-fpv-lipo-battery
https://www.amazon.com/usmile-receiver-Support-FS-iT4S-Evolution/dp/B07FMFG6Q3/ref=sr_1_1?s=toys-and-games&ie=UTF8&qid=1542217789&sr=1-1&keywords=fli14
https://www.amazon.com/Flysky-FS-i6X-Transmitter-FS-iA6B-Receiver/dp/B0744DPPL8
https://www.getfpv.com/new-arrivals/ev-peak-e3-falcore-edition-35w-3a-lipo-battery-balance-charger.html
https://www.amazon.com/dp/B01N4571Q6/ref=as_li_ss_tl?psc=1&linkCode=sl1&tag=fpvknowitall-web-20&linkId=6769f39dd3014cb5619db31a54b18438
https://www.racedayquads.com/products/rdq-quad-solder-38-62-0-8mm-100g
https://www.amazon.com/DOWELL-Stripper-Multi-Function-Tool%EF%BC%8CProfessional-Craftsmanship/dp/B06X9875Z7/ref=sr_1_4?s=hi&ie=UTF8&qid=1542221619&sr=1-4&keywords=wire+stripper+and+cutter
https://www.amazon.com/NEEWER-Titanium-Nitride-Driver-Wrench/dp/B00CP2GGBI/ref=as_li_ss_tl?ie=UTF8&qid=1488911480&sr=8-3&keywords=hex+driver&linkCode=sl1&tag=dre-youtube-20&linkId=d53d845db871ab90fe110b2918f60a7e
$381 no shipping/tax and the build kit comes with accessory kit including motor screws for CL1 5mm thick arms, double-sided tape, FC stack mounting screws, XT60 power lead, zip ties, and heat shrink.
​
Your idea seems like it may be "too little" for the project but I am honestly ok with that because I rather get something done then bite off something too big to chew and end up having to figure something out last second and it being a piece of crap.
​
So does that flight controller stick right into those frames and then you screw them in or something? You say I only need to solder the the power wires to the camera, where do the motors go? I probably sound like an idiot but I'm not really an electrician or carpenter, I don't build things, other then computers :P. I need to head off now so I can't do so much research right now and I spent all day researching today.. won't have much time tomorrow, we are going to tour a college. Can you recommend a good video that would go along with this build? Tomorrow, I am going to ask the teacher if the TV in the room I am presenting in has analog input, if not we go from there. We have access to a 3D printer but a lot of people are going to be using it most likely and I think its slow but I can definitely get the camera mount printed. Once again, appreciate the effort.
Yeah it's a pretty common cheap tx for beginners. I can't find any mode 2 tx on Amazon. I think this one is a mode 2 so should work.
https://www.amazon.com/dp/B0744DPPL8/ref=cm_sw_r_cp_apa_cpaSBbFCTAAFP
And here's the cable you need for use with simulators or any game.
https://www.amazon.com/dp/B01AAETLVY/ref=cm_sw_r_cp_apa_XuaSBbYTBB400
Or if you want a better Tx that's 'futureproof' consider paying more and getting a Taranis Qx7. It's about 100 bucks and both the hardware and firmware are better in quality and there is gobs and gobs of support online as it's one of the most used TX in the whole RC hobby. Plus there's no extra adapter cable needed to use with Sims. Any micro USB cable, plug it in to your PC and it's auto recognized by most Sims.
https://alofthobbies.com/frsky-taranis-q-x7.html
https://www.amazon.com/dp/B06XQWQ7C3/ref=cm_sw_r_cp_apa_fMaSBb5CRX90A
Would this one be better? Flysky FS-i6X 10CH 2.4GHz AFHDS RC Transmitter w/ FS-iA6B Receiver https://www.amazon.com/dp/B0744DPPL8/ref=cm_sw_r_cp_apa_cmWLAbDBVVNP2
Awesome, will do. Do you know if the kit I picked out can support 4S batteries? I've read that your components need to be able to handle the extra current. I'll read up on the x6b receivers :). Also, what are your thoughts on the I6x?
https://www.amazon.com/dp/B0744DPPL8/?coliid=I24XHKH2B0O5Y8&colid=3E2Q40NU5VK0A&psc=1&ref_=lv_ov_lig_dp_it
Since I recently purchased the receiver, I think I'll just return it and start over. This looks like it should have what I need: https://www.amazon.com/Flysky-FS-i6X-Transmitter-FS-iA6B-Receiver/dp/B0744DPPL8/ref=sr_1_1_sspa?ie=UTF8&qid=1519086107&sr=8-1-spons&keywords=flysky&psc=1
Any thoughts?