Reddit mentions: The best flow sensors
We found 8 Reddit comments discussing the best flow sensors. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 7 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Gems Sensors 226100 FT-330 NSF Approved Materials Flow Sensor
- Body Material: Noryl
- Flow Range (GPM): 0.4-4.0
- Port Size: 3/8" NPT Male
- Recommended Filtration: 50 micron
Features:
Specs:
Number of items | 1 |
Weight | 0.0220462262 Pounds |
2. DIGITEN G1" Water Flow Hall Effect Sensor Switch Flow Meter Flowmeter Counter 1-60L/min
Flow range:1-60L/min, Sensor: Hall effect.Allow compression:Water pressure 1.75 Mpa belowWorking voltage range:DC 5-18 VOutput Waveform:Square Wave,output pulse signal.Work for Android and PI system.
3. uxcell G1/4 inches Hall Effect Water Flow Sensor Switch Flowmeter Fluid Meter, 0.25-3L/minute
- All materials are in line with RoHS testing standards
- Light weight, small Size, easy to install
- Three wire connection: red for positive, black for negative, Yellow for pulse signal
- The water flow sensor is applied for water heater, and can be used as flow switch
- Maximum water pressure: 0.8MPa, flow range: 0.25-3.0L/min
Features:
Specs:
Number of items | 1 |
Size | G1/4" Male x G1/4" Male |
Weight | 0.07 Pounds |
4. DIGITEN G1-1/2" 1.5" Water Flow Hall Sensor Switch Meter Flowmeter Control 10-150L/min
- Flow range:10-150L/min
- Allow compression:Water pressure 1.75 Mpa below
- Working voltage range:DC 5-18 V
- Output Waveform:Square Wave,output pulse signal.
- Sensor:Hall effect
Features:
5. EKM Metering 3/4" Water Meter - Stainless Steel, Pulse Output
- Stainless steel body and fittings
- Simple 2-wire connection between water meter and kWh meter
- No additional power source required
- Pulse count can be read remotely using the free, remote reading, EKM Dash software.
- Quality materials and construction, 3/4" NPT Male Threads
Features:
Specs:
Height | 6 Inches |
Length | 13 Inches |
Weight | 100 Kilograms |
Width | 4 Inches |
6. DIGITEN G3/4" Water Flow Hall Sensor Switch Flow Meter Flowmeter Counter 1-60L/min
Flow range:1-60L/minAllow compression:Water pressure 1.75 Mpa belowWorking voltage range:DC 5-18 VOutput Waveform:Square Wave,output pulse signal.Sensor:Hall effect
7. 6560-860, Sundance Spas - Hot Tub Flow Switch
- Sundance Spas Flow Switch with Bypass 6560-860
- Original Sundance Spa Parts. No generics
- Flow Switch with transparent tee 3/4" barb with a 3/8" barb off the side
- 3/4" barb replaces part # 6560-858
- Flow Switch used on Sundance Spas 800/850/880 Series Spas, 1999 - Present
Features:
Specs:
Color | Blue |
Height | 4 Inches |
Length | 2 Inches |
Number of items | 1 |
Width | 6 Inches |
🎓 Reddit experts on flow sensors
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where flow sensors are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
So if you want cheap you can use - http://www.ebay.com/itm/G3-8-Water-Flow-Sensor-Flowmeter-Switch-Controller-Meter-0-3-10L-min-/201402645132?hash=item2ee4887a8c:g:WQoAAOSwT6pVxD1H
I haven't tested that one yet but I plan on using it on my second tap just to verify that it works with my system.
I'm currently using this one - http://www.amazon.com/Gems-Sensors-226100-Approved-Materials/dp/B005T692BI
I got it cheaper form the kegbot store back in the day but they don't sell them there anymore. I'm sure you could shop around to find one for around $85
There is also the SwissFlow but it uses BSP threads - http://www.swissflow.com/sf800.html
I've used this in the past with an Arduino and it worked fine. I just had to add a lot of thread tape since i didn't have a BSP to NPT converter.
A lot of this info can be found on the kegbot forums.
I assume you've seen these water flow meters on Amazon? https://www.amazon.com/DIGITEN-Effect-Sensor-Flowmeter-Counter/dp/B00VKAT7EE
I thought about doing using these for the irrigation to check if it's off or not, but it's pulling water from a canal, which means weeds and whatnot would clog the wheel. So I'll have to rely on some indirect solution.
Look for a "hall effect" flow sensor to give you a measurable flow rate. Not sure what you plan to use to read the sensor, I've interfaced these with an arduino before. Something like this? https://www.amazon.com/uxcell%C2%AE-Effect-Sensor-Flowmeter-0-25-3L/dp/B01FJRA4IQ
3/4" Water Meter - Stainless Steel, Pulse Output https://www.amazon.com/dp/B00GM5DCCA/ref=cm_sw_r_cp_api_Xm4nzb7SRPH0W
Try this?
How about a flow switch ? Hook it to a pi zero and count time that it runs. Calculate amount of water a minute the pump moves, and you can see how much a day it has pumped out give or take a gallon or so.
The included charger is designed for 12V batteries. Just about any 12V SLA UPS battery should work.
Add a Water Flow Hall Sensor to monitor for failed solenoid & leaks.
Yes, check valves etc. It was a definitely a unit "death" as after 7 months, my hot tub breaker kept flipping and by process of elimination, it was the Ozone generator causing the problem. Disconnected it and no more breaker flips. Connected it again, breaker immediately flipped. Spoke to manufacturer and they said that means it's dead.
And yes, I meant flow switch (the little reed sensor that's inline with the flow). Right after that, there's a little port. Why is that wrong? it's literally in my spa hot tub manual as the point of connection?
What is that port for?
https://www.amazon.com/6560-860-Sundance-Spas-Jacuzzi-Switch/dp/B0031B6Y9G/ref=asc_df_B0031B6Y9G/?tag=hyprod-20&linkCode=df0&hvadid=167126215582&hvpos=1o2&hvnetw=g&hvrand=15249422066160976126&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9030963&hvtargid=aud-801738734305:pla-338035636044&psc=1