Reddit mentions: The best industrial pumps
We found 31 Reddit comments discussing the best industrial pumps. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 13 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. bayite 12V DC Fresh Water Pump with 2 Hose Clamps 12 Volt Diaphragm Pump Self Priming Sprayer Pump with Pressure Switch 4.5 L/Min 1.2 GPM 80 PSI Adjustable for RV Camper Marine Boat Lawn
- The patented design delivers smooth & consistent flow at all ranges of operation, while drawing low current
- Inlet and Outlet: 3/8-inch hose barb ports. Vertical Suction Lift: 6.6ft (2m). Adjustable CUT-OFF Pressure: Default 80-85PSI, MAX 100 PSI(5.5Bar). It doesn't mean 4.5L/min jet at 100PSI. Comes with 2 tube clamps
- The pump body is sealed to prevent incidental moisture and dust from entering. The pump can not run continuously more than 6 hours. Able to operate in a wet environment. Self priming function allows it to be mounted above water tank
- Sealed switches and electro coating to inhibit corrosion. Soft rubber mounting tabs to reduce vibrations. When installed correctly, Marine Duty Fresh Water Pumps provide years of quiet operation
- The pump in combination with a low backpressure water system can exceed all expectations
Features:
Specs:
Height | 4 Inches |
Length | 8 Inches |
Number of items | 1 |
Weight | 0.881849048 Pounds |
Width | 3 Inches |
2. General Hydroponics HGC728040 Dual Diaphragm Air Pump 320 GPH 4 Outlet
- General Hydroponics Dual Diaphragm air pump is the only air pump in the world that is manufactured exclusively for use with hydroponics systems
- This high output pump (320 mph/24, 800 cc/minute capacities) has four adjustable 1/4" outputs
- In addition, growers who use our Dual Diaphragm air pump can count on it to reliably oxygenate their reservoir with air stones
- Made in South Korea
Features:
Specs:
Height | 6.1 Inches |
Length | 7.1 Inches |
Number of items | 1 |
Size | 1-(Pack) |
Weight | 1.36 Pounds |
Width | 5.2 Inches |
3. ZJchao Peristaltic Liquid Pump [Electronics]
- Arduino Pump, The pump is basically a geared down DC motor, so it has a lot of torque. Inside the pump is a 'clover' pattern of rollers. As the motor turns, the clover presses on the tube to press the fluid though. The pump does not need to be primed and in fact can self-prime itself with water a half meter with ease.
- Intllab Peristaltic Pump 12v, You can PWM the motor to speed up or slow down the flow rate and if you connect the motor the other way it will move fluid the other direction. Works great with either a power transistor (basic on/off) or a motor driver chip such as the L293D. Features. Uses 3/16"" (4.7mm) outer diameter silicone tubing. Working Temperature: 0 ℃ - 40 ℃.
- Wolfcraft Peristaltic Pump Wolfcraft, Motor voltage: 12VDC. Motor current: 300mA. Flow rate: up to 100 mL/min. Weight: 200 grams. Dimensions: 27mm diameter motor, 62mm total length. Mounting holes: 3mm diameter, 5mm center-to-center distance.
- 12v Dc Diy Peristaltic, Dia.27.6 x Height 37.9 (mm) Pump head size(Φx H):Dia. 31.7 x Height 20.1(mm) pump tube size(IDxOD) :2.5*4.7mm weight: 200g
- DIY Dosing Pump Peristaltic Dosing Head, pump tube (ID x OD) : 2.5mm inner diameter x 4.7mm
Features:
Specs:
Height | 1.06299 Inches |
Length | 2.83464 Inches |
Width | 1.06299 Inches |
4. Zology Water Pressure Pump Self Priming RV Fresh Water Diaphragm Booster for Industrial Hydraulic Equipment,Water Filter System and Irrigation System
- Low Power Consumption(70Watts),High Performance(6L/Min,131 PSI)
- Easy to Install and Use:Good Replacement for Your Old Pump,Max inlet hose Length: 2 meters Pump head: 70 meters Max flow rate: 6L/Min Boost pressure: up to 0.9-1.0 Bar Inlet/outlet caliber: 3/8" (10mm),Power supply:12V
- Widely Used both in Industrial and Daily Life:Hydraulic Equipment,Water Filter System,Garden Watering System,Irrigation System,House Cleaning,etc.(Of Course You Need to Use Your Own Hose and Sprayer)
- High Quality Smart Motor:Over Pressure Protected,Stop Pumping When Pressure is Overload,Automatically Recover When Pressure Back to Normal
- Corrosion Resistance,Anti-Rust,Solid Construction.12-Month-Warranty,Easy-to-Reach After Sale Service
Features:
Specs:
Weight | 1.3 Pounds |
5. Fill-Rite FR112 Rotary Vane Hand Pump with Discharge Hose, Nozzle Spout, and Suction Pipe
- Top selling Fill-Rite product since the 1960's - highly durable and easy to use
- Flow-rate of 10 gallons per 100 revolutions
- Pump can easily be setup for reverse flow
- Pump can be padlocked for safety or security
- Cast aluminum housing for corrosion resistance and light weight
Features:
Specs:
Color | Red |
Height | 8.8 Inches |
Length | 8.8 Inches |
Number of items | 1 |
Size | Rotary w/Spout & Hose |
Weight | 0.8 Pounds |
Width | 23.8 Inches |
6. Peristaltic Pump with 42 Stepper Motor Dosing Tubing Hose Pump Small Flow 0~160ML/min (with 42 Motor)
- ✅This is a pump head with integrated design of the motor pump head. It has a large volume reduction and reasonable structure. It is suitable for the OEM pump head, with flexible upper pressure block and adaptive different hoses.
- ✅Speed range: 1 ~ 50.0rpm, forward and reverse reversible.Speed resolution: 1rpm (external control 0.1rpm).Voltage: 6-24V.Power consumption: <10W.Working environment: temperature 0 ~ 40 °C, relative humidity < 80%.
- ✅ This is a pump head with integrated design of the motor pump head. It has a large volume reduction and reasonable structure. It is suitable for the OEM pump head, with flexible upper pressure block and adaptive different hoses.
- ✅Flexible and easy to replace hose.Suitable for OEM products.Shell material: Nylon.Dimensions: 57x57x62mm/2.24x2.24x2.44inch.Color: Black.Quantity: 1 Pc.
- ✅ Small size and light weight.Can be mounted on the work panel or mounted on a stand.
Features:
Specs:
Color | BLACK |
Number of items | 1 |
Weight | 0.661386786 Pounds |
7. Laing D5-Strong-790N Centrifugal Pump
- Laing D5-Strong-790N Centrifugal Pump
Features:
Specs:
Number of items | 1 |
8. AR North America AL554-B, Blue Clean 22 mm Fitting, M15QC x M14 Plug, Pack of 50 pcs
- Price for Pack of 50 pcs
Features:
Specs:
Number of items | 50 |
9. AR North America AL553-B, Blue Clean 22 mm Fitting, M14QC x M15 Plug, Pack of 50 pcs
- Price for Pack of 50 pcs
Features:
Specs:
Number of items | 50 |
10. Amazing Drapery Hardware 20 Qty: White Vane Savers for Repairing Curved Vertical Blind Slats
Fix vanes with a broken hole, rehang your vertical blind slats!20 vane savers
Specs:
Color | White |
Height | 6 Inches |
Length | 1 Inches |
Width | 5 Inches |
11. Action Pump 4007 Polyethylene Siphon Pump, for use on 5 Gallon Pails, 2 GPM
- Siphon drum pump for use with kerosene, light oils, and various water-based solvents
- Hand-operated bellows action
- Polyethylene construction for resistance to chemicals
- Flow rate of 2 gpm
- 0.6" discharge spout
Features:
12. Action Pump EZ-55 Food Grade 55 Gallon Double Action Drum Pump
Double action pump for fluid delivery on both up and down strokesMade of polypropylene and polyethylene for resistance to chemicalsPumping mechanism eliminates wear on parts for longer lifeHigh volume delivery at low pressure for safety when pumping chemicals2" NPS and 2" buttress adapters
Specs:
Height | 7 inches |
Length | 0 inches |
Number of items | 1 |
Size | 2" NPT Male & 2 Butress(m) |
Weight | 5 Pounds |
Width | 7.5 inches |
13. Simply Pumps PM200F Peristaltic Industrial Grade Self Priming Dosing Dispensing and Metering Pump with Norprene Food Grade Tubing, 12V DC, 300 mL/min
- Includes award winning Simply Pumps customer support Includes award winning Simply Pumps customer support
- Industrial quality, made in the USA
- Designed for light duty dispensing or metering applications
- Variable speed using our PWM flow controller
- Compatible with many chemicals and aggressive fluids
Features:
Specs:
Height | 2.9 Inches |
Length | 2.4 Inches |
Number of items | 1 |
Weight | 0.5 Pounds |
Width | 3.5 Inches |
🎓 Reddit experts on industrial pumps
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where industrial pumps are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
This fence line is just shy of 90 feet and my setup works pretty well at that length. I used pretty small diameter pvc so it’s not much weight; I can’t imagine reinforcement would be needed for the watering— maybe for the vines depending. It’s not a raging torrent of water it basically is just a steady drip but it saturates pretty well when run in cycles and not run during the heat of the day.
My initial version of this setup was a single battery and small solar panel and it ran fine for a year or more (granted I’m in SoCal so we get a lot of sun)— I’ve since expanded a bit to a 4 battery setup and larger panel but just because I added two more pumps for covering other areas.
Here’s a picture of the control box of a basic single battery system with timer and a simple solar controller
https://i.imgur.com/JOfGqdp.jpg
Here’s some of the basic gear:
Water Storage
===========================
Current Water tank
https://www.amazon.com/dp/B003H9WJMI/
(Although I’ve also used smaller/cheaper tanks like this for my vegetable garden, just might mean more refills depending on how often it’s run: https://www.amazon.com/dp/B01BFC5NIA/ )
If you’re looking to go super cheap, I honestly started my first setup with a couple modified 5 gallon plastic water bottles I stole from my office like these: https://www.amazon.com/dp/B003B27RAA/
Power
===========================
Current solar panel for a 4 battery setup:
https://www.amazon.com/dp/B07HFMBF3G
Previous panel for single battery system:
https://www.amazon.com/dp/B00PFGP0EA
Solar regulator (keeps you from blowing up the battery! The smaller panel comes free with one that works fine, I just liked this one better because it had more lights!): https://www.amazon.com/dp/B00L37KZI6/
Batteries, one is plenty for a single pump system:
https://www.amazon.com/dp/B003S1RQ2S/
(obviously if you wanted to build a system on the cheap you could bypass the solar entirely and drop $20 on a second battery that you leave charging and just swap them back and forth every week or three, depending on how often/long you run the system)
Pump
===========================
Current Pump:
https://www.amazon.com/dp/B072BXBQGC/
Although I’ve also used cheaper ones like these for drip systems and they were fine:
https://www.amazon.com/dp/B07699RMVB
https://www.amazon.com/dp/B00WYMC492
https://www.amazon.com/dp/B00DLKT4OO
Misc
===========================
Timer (has like 16 stop/start memories which should be plenty for any configuration):
https://www.amazon.com/dp/B0090MTLFO
If there is some interest next weekend I could draw up a complete wiring/assembly diagram and detailed parts list and make a separate post (and include all the sundries: wire, hose, clamps, filters, waterproof project box, couplings, drip heads, etc).
Basil, as with all plants, enjoy lots of air. The more air the merrier. The container they are in looks like 14-18 gallon, for which I would recommend an 18 watt ecoplus pump, or even better this diaphragm pump, which though expensive, puts out amazing amounts of air and does not overheat. My watermelons loved it.
This one?
https://www.amazon.ca/General-Hydroponics-Dual-Diaphragm-Pump/dp/B008UF9XLY
I have one, picked it up from indoorgrowingcanada.com and I love it. I had a Fluval Q1(45-80gal) running 2x 8" stones in rez and a Q2(50-160gal) running 5x 4" one in each pail.
I now could run just with the GH dual with 8x 4" stones and also could easily run the 2x 8" in the rez too (they are still on the Q2 for redundancy reasons) and still have air left over for my aerocloner.
Make sure to hang it upside down by the base for quietest operation, but its easily as quiet as my smaller aquarium pump and moves so much more air just sitting upright on the base. Stay away from the eco air style of pumps if noise is an issue.
The only downside is it doesnt have a 3/8s outlet, so I just fed two 1/4 lines to my manifold inside and same same. The valves are easy to use and seal up good. It doesnt get any hotter than an aquarium pump too.
All in all, im real happy with my purchase.
One stone per container is fine. I would buy a better pump like this one https://www.amazon.com/General-Hydroponics-Dual-Diaphragm-Pump/dp/B008UF9XLY and use that to power all the pumps. I have about 5 of these and they work great.
I find this works best
https://www.amazon.com/gp/aw/d/B00O58UIZA/ref=cm_cr_arp_mb_bdcrb_top?ie=UTF8&amp;th=1&amp;psc=1
There is enough room in the base to carve out and install one of these guys in the base
https://www.amazon.com/bayite-Diaphragm-Priming-Pressure-Adjustable/dp/B074MZYS37/ref=mp_s_a_1_8?ie=UTF8&amp;qid=1543100993&amp;sr=8-8&amp;pi=AC_SX236_SY340_FMwebp_QL65&amp;keywords=small+water+pump&amp;dpPl=1&amp;dpID=51RkfxQN6rL&amp;ref=plSrch
For extra fun you can also install an inline juicer for a pour and play setup.
Reccomended ass milkshake recipe is-
5 grams psylocybe azuricans
15 peyote buttons
350mg ketamine
3 tabs acid
1/2 bottle of everclear
10g dmt
This is an easy fun home diy boof machine that you can make in under an hour!
I bought 4 peristaltic pumps (because they are food safe) from:
http://www.amazon.com/gp/product/B00HIX2PEG
some cheap food safe tubing (about $3), an RPi, A webcam (I use a Logitech c310) for the microphone, and a spark.io board and relay shield:
https://www.spark.io/
Total cost (minus the pi) is probably a little over $200. You really don't need the spark board though (it's new so I wanted to play with it). So you could cut it down to about $125
The relay code is really easy on the spark since it is just the default relay code. I wrote a quick script that sends the on api command, waits 60s, then sends the relay off api command. The voicecommand software you can get from:
http://stevenhickson.blogspot.com/2014/08/voicecommand-image-file-and-controlling.html
I'll probably extend it further with a touch screen and some more stuff and do a full write up at some point.
Was thinking about going with this guy. Bayite 12V DC Fresh Water Pump
I know you don’t know my set up, but you think this would work? I’ve been trying to piece together this project with minimal knowledge on solar, pressure, & volume.
Thanks for the help!
Yeah a pool pump is definitely not a good fit. It is designed for high flow low pressure, you need the opposite.
I found a decent style of pump, an rv pump.
https://www.amazon.com/gp/aw/cr/B074MZYS37/ref=mw_dp_cr
This one is a bit small only 1 GPM but it makes 80 PSI and it's cheap.
Something like this would be better but it's more expensive:
https://www.amazon.com/SHURFLO-4008-101-E65-Revolution-Water-Pump/dp/B002XM5G70
The first one has a couple reviews about people making portable showers
I got this pump it’s a bit loud but works great.
Sound cool.
A few observations, if you don't mind me butting in.... Sounds like a really good application for a small peristaltic pump. If you are using some other type of pump, like an impeller pump, it might be higher flow than you need. A peristaltic pump and a relay would probably work.
here's one for low flow apps that is $23. There are tons on amazon and ebay:
http://www.amazon.com/ZJchao-Peristaltic-Liquid-Pump-Electronics/dp/B00HIX2PEG/ref=sr_1_1?ie=UTF8&amp;qid=1452885463&amp;sr=8-1&amp;keywords=Peristaltic+Pump
I can appreciate your reluctance to use discrete semiconductors. (You are already using integrated semiconductors, of course.) It's a little trickier to make your own DC drivers out of discrete parts, but fortunately, there are many alternatives to that.
For one, you can use what's called an "H-bridge", which does both the direction changing and the driving of a DC load, and it's probably as easy to use as an SSR. You need one lead to "steer" and one lead to "drive". Another advantage of this is that you can use pulse width modulation, which preserves torque at low speeds and allows control over the speed of the pump. It also allows almost instant braking of the motor. When you turn that sucker off, it stops.
https://en.wikipedia.org/wiki/H_bridge
here is a data sheet for one from Mouser Electronics:
http://www.mouser.com/ds/2/405/lmd18200-440916.pdf
They are $15 in quantity 1.
http://www.mouser.com/ProductDetail/Texas-Instruments/LMD18200T-NOPB/?qs=sGAEpiMZZMvu8NZDyZ4K0cK2%252bZITVZKj
No harder to use than an SSR, I think. (I chose this one instead of 100 other because of its packaging. It's a TO-220 package and you can cram it into a PCB board without having to deal with surface mounting. (Heat sink it, though.)
For what you want to do using relays and slower pumps is the simplest, and using h-bridge and any pump is the most flexible.
If you want to do other things downstream of this, getting familiar with H-bridges is a good learning experience and will pay off more.
[edit: package]
don't forget the accessories.. Fill-Rite FR112 Rotary Vane Hand Pump with Discharge Hose, Nozzle Spout, and Suction Pipe https://www.amazon.com/dp/B0000AX0YM/ref=cm_sw_r_cp_apa_i_Joq0Db87K0XV6
> Korean diaphragm airpumps
Like This?. Have you used this pump? How many do you think I need for my system? Looks like regen blowers pull way too much current.
Cool! The converter I linked will need soldering, but here's one that doesn't. You should be aware that the motors you have linked offer very unreliable flow control, so use a stepper motor driven pump if you need fine control over the amount of liquid flow.
Unless its a commercial air pump, which you dont need for 10 gallons it should be whisper quiet. Look into the Eco whisper series, they come in various sizes, all of which are quiet until you get to the commercial level. IF you feel you need heavier air output from a commercial size BUT you also need it quiet id go with https://www.amazon.com/General-Hydroponics-Dual-Diaphragm-Pump/dp/B008UF9XLY
Its what I use indoors for DWC 60 gallons across 4 reservoirs and it does fine.
TLDR; Your pump can be small enough that you shouldnt even hardly hear it running if at all
I'm guessing something like this would constitute a 'bad idea':
https://www.amazon.com/bayite-Diaphragm-Priming-Pressure-Adjustable/dp/B074MZYS37/ref=zg_bs_1265115011_1?_encoding=UTF8&psc=1&refRID=VXF76MA1K4BF6S10CF8S
Also yes, using cylindrical fiber filters.
You're not looking hard enough ;)
http://lowara.com/pumps-circulators/wet-rotor-circulators/d5-high-efficiency-circulator-with-dc-motor/
https://www.pumpvendor.com/Laing_Pump_List.html
https://www.amazon.com/Laing-Pumps-D5-Strong-790N-Centrifugal-Pump/dp/B00E5USVGQ
Alright so, what you've got there are M22 couplings -- for simplicity's sake, let's call the side with the external threading M22-A and the side with the spinning nut M22-B.
The issue is that the standard internal size is 15mm (that's the width of the stem on part M22-B and of the hole it slides into on part M22-A), but chinese machines and accessories often use 14mm for some stupid reason, causing all sorts of incompatibilities. It's a very frequent issue.
The problem you're gonna be facing if you order kits like the one you linked is that it'll only ever fit one of your connections. Instead, consider these adapters:
Obviously you shouldn't order those packs of 50 units, but they are actually the correct parts. If you look around with the part numbers I gave you, you should find them pretty easily.
Will change your life, I guarantee it.
Yeah my two air stones are bubbling away now with [this] (https://www.amazon.ca/Marina-11116-200-Air-Pump/dp/B0048AOQK8). Its a pretty basic air pump but it seems to be going alright. It's only aerating about 7-8 gallons of water. Its replacing my old pump that broke.
https://www.amazon.com/Action-Pump-Polyethylene-Siphon-Gallon/dp/B00MWO9QN4
I use these for soy sauce. May have to add some extension to the output end, though.
Here's the pump we bought for multiple buckets http://www.amazon.com/gp/product/B008UF9XLY?psc=1&amp;redirect=true&amp;ref_=od_aui_detailpages00
You can even tee them off to do 8 buckets.
https://www.google.com/url?sa=t&amp;source=web&amp;rct=j&amp;url=https://www.amazon.com/bayite-Diaphragm-Priming-Pressure-Adjustable/dp/B074MZYS37&amp;ved=2ahUKEwj7zcOjgrXiAhWhxlQKHcjHDpsQFjAAegQIBRAC&amp;usg=AOvVaw2CG6WXejhWSatkNrjFgl-G
https://www.google.com/url?sa=t&amp;source=web&amp;rct=j&amp;url=https://www.amazon.com/Seaflo-Pre-Pressurized-Accumulator-Tank/dp/B01MVA6GCC&amp;ved=2ahUKEwj6uZq3grXiAhVIl1QKHepiCjEQFjAEegQIAxAB&amp;usg=AOvVaw0p7IxyCFGVv0hAILggLjyL
this will probably prove helpful, it's a paristaltic pump so the fluidic path never directly contacts the mechanical elements (as opposed to a syringe pump). PWM-able for timing control, and you can likely control the flow rate further by using varying inner and outer diameters of tubing.
https://www.amazon.com/Action-Pump-EZ-55-Gallon-Double/dp/B00866C8X2
I use an 12v rv water pump and a 12v power supply. The rv pumps are based on a diaphragm design and can handle a bit of debris going through them. I actually use an old computer power supply that you just have to mess with a little to perform the same function as the linked one. Just make sure your suction line is below your water level, it should stay primed.
If you pressurize a bottle it will drive the fluid out of it as long as the inlet for the fluid is below the fluid line. One danger is pressurizing the bottle may break it sending glass flying. Another problem is most compressors put a little bit of oil in the air it compresses. (not exactly a food grade idea.)
I have used a similar vacuum device. The exhaust is going to be a mixture of air and fluid if you attach the suction side to a bottle of liquid. It may work but you may not like the compressed air coming out of your nozzle. Again not a food grade solution.
I suggest one of these