Best body repair putty according to Reddit
Reddit mentions of J-B Weld 50132 PlasticWeld Quick-Setting Epoxy Syringe - Translucent Yellow - 25 ml
Sentiment score: 4
Reddit mentions: 9
We found 9 Reddit mentions of J-B Weld 50132 PlasticWeld Quick-Setting Epoxy Syringe - Translucent Yellow - 25 ml. Here are the top ones.
- J-B WELD PLASTICWELD: A quick setting and multipurpose two part epoxy that provides a strong and lasting bond on various plastic surfaces (Plastic & PVC, Fiberglass, Glass, ABS, Composites and Vinyl). J-B Weld PlasticWeld comes in a syringe allowing for an easy 1:1 mix ratio. The unique syringe has a re-sealable cap that prevents drying out and leaking, allowing for multiple uses!
- CURE AND SET TIME: After mixing the two part formula with the included mixing tray and stir stick, PlasticWeld takes 5 minutes to set and 1 hour to cure. J-B Weld PlasticWeld set and cure color is Translucent Yellow.
- STRENGTH: J-B Weld PlasticWeld has tensile strength of 3900 PSI.
- SURFACE APPLICATIONS: Plastic & PVC, Fiberglass, Glass, ABS, Composites and Vinyl.
- DO IT YOURSELF: Big or small, you can DIY it with J-B Weld. Our heavy duty epoxy and adhesives repair & restore it right the first time. J-B Weld delivers superior performance, quality, and results for the World’s Strongest Bond.
Features:
Specs:
| Color | Clear |
| Height | 7.086614166 Inches |
| Length | 1.574803148 Inches |
| Number of items | 1 |
| Release date | September 2012 |
| Size | 25 ml |
| Weight | 0.1 Pounds |
| Width | 1.181102361 Inches |
▼ More
#1 of 22
JB PLastic Weld for the tank. Saved my ass when I accidentally snapped off one of the ram clips in my computer. Works just like it sounds. Good as new.
JB Weld plastic epoxy works great for mending plastic.
I use it quite often.
If it's just cosmetic, I'd take it to a shop and get it sanded and repainted (or do it yourself!). If it is cracked, there are plenty of ways to repair a crack with ABS cement. Ebay is only really if the fairing piece is beyond repair, since anything off of Ebay for a bike that old will not be in pristine condition. Get it fixed, I've always loved the way the 90's GSXR's look!
I would take the driver assembly off of the frame (aka remove the thand use an epoxy specially formulated to bond plastic to glue the pieces together. I recommend JB PlasticWeld. You probably want to practice on something else before you try it on your cans, since it dries super quick and you only have one shot at this.
One that has fully cured (it says 1hr but definitely give it a full 24hours), I would wrap the cracked part of the frame tightly in a self-sealing tape. This is a rubber tape which resembles electrical tape but it has no 'adhesives'. What you do is stretch it out as you wrap it and then tightly overlay half of the width over your last pass each time. It will fuse to itself and should support it pretty well. Make sure you have enough clearance to put the layer of tape on and still reattach the driver assembly back on, because once it's one there it's not going to come off without a huge fight (which is the whole point). Again, practice beforehand on something else. I personally use the 3M brand all the time with good results, and it's super cheap. Link.
Good luck.
Just grab some milliput, it's what I use for this purpose and it is pretty cheap for decent quantities on eBay in the UK.
Source: Also UK and make things.
EDIT:
Conversely, I've just looked this up, as suggested by the other human: https://www.amazon.co.uk/J-B-PlasticWeld-Epoxy-50132-Plastic/dp/B009EU5ZMK
Both 3D printed accesoriees (the front left tactical rail for the flashlight and the 8 dart holder) were glued on using JB Plastic Weld. The front rail needed some additional support so it got some hot glue on the sides too.
https://www.amazon.com/J-B-Weld-50132-PlasticWeld-Quick-Setting/dp/B009EU5ZMK
Thanks JB Weld seems like it should do the trick?
Two part epoxy might work? JB plastic weld