Reddit mentions: The best automotive suspension ball joints
We found 6 Reddit comments discussing the best automotive suspension ball joints. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 5 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. Moog K8771T Ball Joint
- PROBLEM SOLVER GUSHER BEARING -- Metal-to-metal design provides strength and allows grease to flow through bearing surface for reduced friction and long life
- STRONG AND DURABLE -- Ball studs are heat treated to match or exceed OE requirements to inhibit premature failure and improve fatigue strength
- GREASEABLE SOCKET -- Reduces corrosion and wear by allowing new lubricant to flush contaminants
- KEEPS DIRT AND WATER OUT -- Pre-installed dust boot shields socket components from wear-causing contaminants
- ABSORBS IMPACT -- Belleville preload washer helps keep the bearing package tight as bearings wear
- EASY TO INSTALL -- Precision tolerances for easy installation and steering alignment giving you a perfect fit right out of the box
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
Features:
Specs:
Color | Regular |
Height | 0.6 Inches |
Length | 0.6 Inches |
Number of items | 1 |
Release date | September 2013 |
Weight | 1.4 Pounds |
Width | 1.6 Inches |
2. ACDelco 46D2172A Advantage Front Lower Suspension Ball Joint Assembly
- Forged housing for durability
- Undergo extreme impact, wear, and fatigue testing to ensure quality and durability
- Coated for corrosion resistance
- Manufactured at ISO 9001-certified facilities
- Forged, machined shell provides strength
Features:
Specs:
Height | 3.5 Inches |
Length | 4.2 Inches |
Number of items | 1 |
Weight | 0.6 Pounds |
Width | 4 Inches |
3. ACDelco 45D2206 Professional Front Lower Suspension Ball Joint Assembly
- one-piece forged housing for strength
- undergo extreme impact, wear, and fatigue testing to ensure quality and durability
- greaseable design for long life
- coated for corrosion resistance and long life
- manufactured at ts 16949-certified facilities to ensure consistent high-quality
- Fit type: Vehicle Specific
Features:
Specs:
Height | 2.7 Inches |
Length | 4 Inches |
Number of items | 1 |
Weight | 0.9 Pounds |
Width | 3.2 Inches |
4. Moog K3134T Ball Joint
- PROBLEM SOLVER GUSHER BEARING -- Metal-to-metal design provides strength and allows grease to flow through bearing surface for reduced friction and long life
- STRONG AND DURABLE -- Ball studs are heat treated to match or exceed OE requirements to inhibit premature failure and improve fatigue strength
- GREASEABLE SOCKET -- Reduces corrosion and wear by allowing new lubricant to flush contaminants
- ABSORBS IMPACT -- Belleville preload washer helps keep the bearing package tight as bearings wear
- RESTORES LIKE-NEW STEERING -- Patented pressed-in cover plate seals out debris and minimizes looseness, reducing bearing wear and promoting longer life
- EASY TO INSTALL -- Precision tolerances for easy installation and steering alignment giving you a perfect fit right out of the box
- COMPREHENSIVE COVERAGE -- Available for foreign and domestic nameplates
Features:
Specs:
Height | 2.75 Inches |
Length | 5.13 Inches |
Number of items | 1 |
Release date | September 2013 |
Weight | 1.36 Pounds |
Width | 3.31 Inches |
5. Beck Arnley 101-7664 Ball Joint
Matches OE form, fit, and functionCoated or plated for corrosion protectionNecessary hardware supplied as needed for a complete installationHardware functionality matches original design configuration and specificationsApplication specific to ensure a correct fit for your vehicle
Specs:
Color | Regular |
Height | 3.2 Inches |
Length | 4.7 Inches |
Number of items | 1 |
Release date | March 2014 |
Weight | 1.24 Pounds |
Width | 2.6 Inches |
🎓 Reddit experts on automotive suspension ball joints
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where automotive suspension ball joints are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
Since you are looking w/ coil springs I am assuming you are 2WD?
May I make a suggestion - for not much more money you can replace everything with quality MOOG parts for not much more than what you're looking at in just replacement ball joints.
MOOG replacement control arm/ball joint assemblies:
Part #RK80052 Front Right Upper; RWD; Front Coil springs
$47.70
http://www.amazon.com/Moog-RK80052-Control-Joint-Assembly/dp/B007ZLN4YG
Part #RK80054 Control Arm/Ball Joint Assembly Front Left Upper; RWD; Front Coil springs
$47.72
http://www.amazon.com/Moog-RK80054-Control-Joint-Assembly/dp/B007ZLN5LS.
For the lowers:
MOOG K8771T Lower Ball Joint Kit
$32.88 (x2)
http://www.amazon.com/Moog-K8771T-Lower-Ball-Joint/dp/B000C5A044.
I did not even research the best prices and this is what I came up. So for a huge upgrade in part quality you are looking at a total of ~$161.18
This is the item https://www.amazon.ca/dp/B006N9IBNA/ref=cm_sw_r_cp_apa_i_9YXxDb9YXD9ZV
Ordered two of them, both came like this
Not knowing your year, 4wd or 2wd, I guessed for a 2000 4wd cherokee. Labor is between $70-$110/hr at most places. It's $85/hr at a place I'm very uh familiar with.
ball joints $23.64 x 4
https://www.amazon.com/Moog-K3134T-Ball-Joint/dp/B000C542NY
Tie rod ends $25.99 x 2
https://www.amazon.com/Moog-ES3096L-Tie-Rod-End/dp/B000C59W7U
U-Joint $20.07
http://www.autopartswarehouse.com/sku/Jeep/Cherokee/Moog/U_Joint/2000/MO371.html?apwcid=gglpla&gclid=CIjEl_zD09ACFYyLaQodfTYC3Q
OR buy the entire kit
http://www.moog-suspension-parts.com/moog-packagedeal041
BB6 Prelude Ball Joints sir.
https://www.amazon.com/dp/B000C9Q0VM/ref=pe_385040_30332200_pe_309540_26725410_item
https://www.amazon.com/Beck-Arnley-101-7664-Ball-Joint/dp/B00HHNHONO
Sorry it is $60, those are the ones I installed on my 03 350z, grab a master bushing kit from AutoZone , take control arm off, take sway bar link off, push control arm out of the way, take cone bushing off and press it out, press the new one in, install new cone, reinstall control arm, done. 40min per side at most.