Reddit mentions: The best fall arrest equipment
We found 36 Reddit comments discussing the best fall arrest equipment. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 25 products and ranked them based on the amount of positive reactions they received. Here are the top 20.
1. KwikSafety (Charlotte, NC) THUNDER 3D Ring Safety Harness (Pass Through Connectors) OSHA ANSI Industrial Full Body Fall Protection Personal Equipment Construction Carpenter Scaffold Contractor
- WE DON'T CUT CORNERS ON SAFETY: This construction harness is a durable, heavy duty, high performance Full Body Harness that meets and exceeds ANSI/ASSE Z359.11-2014 standards. Our safety harness fall protection is the complete safety package. Be seen and safe with the fluorescent yellow synthetic material. Use with any compatible fall protection safety lanyard, energy absorbers, lifelines, and anchorage lanyards. Safely perform the job knowing the THUNDER fall protection harness has your back!
- HEAVY DUTY D-RINGS: Our fall arrest harness is fully equipped with two side (2) D Rings and (1) Dorsal Ring suitable for primary fall arrest attachment, travel restraint, and rescue. The construction harness has load bearing straps, made from pure, non-recycled synthetic material that is water repellant, has superior stitching, and resistant against ageing, heat, and abrasion. Ensure a safe and proper fit with three (3) pass-through buckles located on the hips, chest and legs of the harness.
- PROPER FIT, PROPER PERFORMANCE: Regardless if its a mens or womens harness, correct fit is essential for proper performance. Our adjustable construction safety harness supports users within a small medium large capacity range of 130 to 310 pounds (59 to 140 kg), 4’10” to 6’6” (147 to 198 centimeters) due to the adjustment points. To ensure your harnesses properly fit, see that all buckles are connected, leg and shoulder straps are snug, and chest straps are in the center of the chest area.
- WE MET THE STANDARD, THEN ROSE ABOVE IT: ANSI/ ASSE Z359.11-2014 - All of KwikSafety’s full-body harnesses have undergone the “Qualification and Verification Testing of Fall Protection Products.” The THUNDER exceeds the already-rigorous ANSI testing standards and is heavy-duty, high-performance fall protection you can trust to have your back. Working at heights 6 ft or more? Equip yourself with the proper fall arrest system. View the Compliance Label/ Safety Label for more information.
- OSHA APPROVED: The Occupational Safety & Health Administration assures men and women safe and healthful working conditions by setting standards and providing training, outreach, education, and assistance. A personal fall arrest system is required when working 6ft. or more above lower levels. The THUNDER safety fall protection harness is ideal for a roofer, ironworker, construction work, arborist work, high-rise window cleaning, gutter cleaning, roofing and thatching, and Search and Rescue.
Features:
Specs:
Color | 1 Pack: Harness |
Height | 10.6 Inches |
Length | 14.2 Inches |
Size | 3 D-Ring Harness |
Weight | 0.41 pounds |
Width | 8 Inches |
2. Ergodyne Squids 3400 Glove Clip Holder with Dual Clips, Black
- KEEPS GEAR CLOSE – Hold gloves, mittens, keys, PPE, towels and more keeping them at the ready
- TWO STRONG CLIPS – Dual clip model connects to clothing, belt loops, tool belts, d-rings and more
- DURABLE – Ultra-resilient acetal copolymer and thermoplastic polyurethane materials are non-conductive and temperature resistant
- PATENTED BREAKAWAY DESIGN – Safely separates and allows for individual clips to be used independently on key chains, d-rings and more
- PREVENTS DROPPED & LOST OBJECTS – Reduces injuries and prevents dropped, lost and foreign objects by keeping gloves, PPE and other gear clipped to the person or worksite
- Measures 6.5in (16.5cm) Long x 1in (2.5cm) Wide x 1in (2.5cm)
Features:
Specs:
Color | Black |
Height | 6.5 Inches |
Length | 1.5 Inches |
Number of items | 1 |
Size | 2 Count (Pack of 1) |
Weight | 0.05 Pounds |
Width | 1 Inches |
3. Ergodyne Squids 3100 Tool Lanyard with Single Carabiner and Adjustable Loop End, Standard Length, Black
- Captive eye carabiner
- Single action aluminum carabiner
- Reflective accent for higher visibility
- Maximum safe working capacity: 10lbs (4.6kg)
Features:
Specs:
Color | Black |
Height | 1 Inches |
Length | 1 Inches |
Number of items | 1 |
Size | Standard |
Weight | 0.21 Pounds |
Width | 1 Inches |
4. KwikSafety (Charlotte, NC) SCORPION Safety Harness w/attached 6ft. Tubular Lanyard on back | OSHA ANSI Fall Protection | INTERNAL Shock Absorbing Lanyard | Construction Carpenter Scaffolding
- FALL PROTECTION GUARDIAN : The KwikSafety SCORPION is a durable, heavy duty, high performance Full Body Harness that meets and exceeds ANSI/ASSE Z359.11-2014 standards. Our harness fall protection is the complete support package because the SCORPION includes a fall protection safety lanyard! The harness is also compatible with other lanyards with shock absorbers, roof lifelines, and anchorage tether lanyards. Safely perform the job knowing the SCORPION fall protection harness has your back!
- HEAVY DUTY D-RING: One back dorsal ring is all it takes to provide functionality on the construction job. The dorsal ring is used for fall arrest & can be used for travel restraint or rescue. The pass-through buckles on our universal harness are made out of synthetic material that is superior to polyester. For some jobs, more fall prevention accessories may be necessary. If an anchor point is needed, like a roofers anchor point or scaffold cross arm strap, we have kits and combos available!
- PROPER FIT, PROPER PERFORMANCE: Regardless if its a mens or womens harness, correct fit is essential for proper performance. Our large adjustable KwikSafety SCORPION full body harness supports users within the capacity range of 130 to 310 pounds (59 to 140 kg), 4’10” to 6’6” (147 to 198 centimeters) due to the adjustment points. To ensure your harnesses properly fit, see that all buckles are connected, leg and shoulder straps are snug, and chest straps are in the center of the chest area.
- WE MET THE STANDARD, THEN ROSE ABOVE IT: ANSI/ ASSE Z359.11-2014: All of our KwikSafety Full Body Harnesses have undergone the "Qualification and Verification Testing of Fall Protection Products". This testing specifies requirements which include the number of specimens to be tested, test equipment to be used, the accreditation of the testing lab and the duties and responsibilities of both the manufacturer and the testing lab. View the Compliance Label/ Safety Label for more information.
- OSHA APPROVED: The Occupational Safety & Health Administration assures men and women safe and healthful working conditions by setting standards and providing training, outreach, education, and assistance. A personal fall arrest system is required when working 6ft. or more above lower levels. The SCORPION fall protection harness is ideal for a roofer, ironworker, construction work, arborist work, high-rise painters, window cleaning, gutter cleaning, roofing and thatching, and Search and Rescue.
Features:
Specs:
Color | Harness |
Size | 1 Pack |
5. Peakworks Roof Anchor Bracket for Fall Arrest System – Connects to Wood Surfaces with Roofing Applications, ANSI and OSHA Compliant, Adjustable Connector Made of Strong, Durable Steel, Red, V8229100
- SAFETY CERTIFICATIONS – Temporary roof anchor bracket meets ANSI Z359 18, CSA Z259 15, and OSHA safety requirements for residential and commercial roofing applications, ensuring your safety in the most dangerous conditions
- REUSABLE ROOFING TOOLS – Re-use this roof anchor bracket as part of your fall arrest system or roofing harness safety kit; roof anchor connects to wood surfaces with a screw size of 3" x #10 (32 screws / 16 per side)
- SUPERIOR QUALITY – Anchor bracket is made with the quality materials ensuring top strength and durability to stand up to the toughest working environments
- STRONG CAPACITY – Hinged roof bracket built with a minimum tensile strength of 5,000 lb. and has a 310 lb. weight capacity; roof harness safety kit
- COMPATIBILITY – PeakWorks Roof Anchors are designed and approved for use only with PeakWorks connectors, or with components that are approved by PeakWorks to be compatible with this product
Features:
Specs:
Color | Red |
Height | 0.87 Inches |
Length | 14.02 Inches |
Number of items | 1 |
Size | Standard |
Weight | 1 Pounds |
Width | 3.82 Inches |
6. 2815 Super Anchor Safety RetroFit Permanent Roof Anchor
- Permanent roof anchor
- Low profile design
- Includes stainless steel fasteners & butyl flashing
- Complies with OSHA standards
Features:
Specs:
Height | 0.5 Inches |
Length | 15 Inches |
Number of items | 1 |
Weight | 0.8 Pounds |
Width | 2 Inches |
7. Conterra Tool Chest Radio Chest Harness (Black)
- Built entirely out of Cordura nylon.
- Cargo pocket, two side mount pockets and elastic keeper.
- Cargo Pocket measures: 7. 75" Tall x 5. 75" Wide x 4" Deep at the top, tapering down at the bottom.
- Penlight, radio, and trauma shears not included.
Features:
Specs:
Color | Black |
8. Guardian Fall Protection 01360 VL58-100 Standard 5/8 Inch Thick Rope with Snaphook End, 100-Foot
- Heavy duty 5/8" poly rope
- Resists cuts and abrasions
- Attached self locking carabiner
- No tangle lifeline available with swivel snap hook
Features:
Specs:
Color | 0 |
Number of items | 1 |
Size | 100 ft |
Weight | 8.51 Pounds |
9. CLC Custom Leathercraft 1025 41-56 in. Interchangeable End Lanyard
3 interchangeable tool ends for quick tool changesHigh visibility 3/4 inch webbing with internal shock cord10-inch webbing loop with dual channel lock for secure tool attachmentCinch or carabiner belt attachmentConvenient webbing loop for belt attachment
Specs:
Color | Multicolor |
Height | 13 Inches |
Length | 6.125 Inches |
Number of items | 1 |
Size | Loop |
Weight | 0.1125 Pounds |
Width | 1 Inches |
10. Guardian Fall Protection 00500 RIDG-1 Single D-Ring Roof Anchor with Nails 11-Inch in Length and 1 D-ring
For permanent use on wood rooftopsMeets standards for fall arrestEasy InstallationStainless SteelComes with a D-ring on one end
Specs:
Height | 3 Inches |
Length | 4 Inches |
Number of items | 1 |
Size | 9¾" |
Weight | 0.7 Pounds |
Width | 3 Inches |
11. Gear Keeper RT5-5801 Micro Key/Tool Retractor with Snap Clip Mount, 50 lbs Breaking Strength, 2.5 oz Force, 36" Extension, Black
- Micro key/tool retractor
- With snap clip mount
- High tensile spectra/nylon line
- Stainless steel spring and hardware
- Made in USA
Features:
Specs:
Height | 1 Inches |
Length | 8 Inches |
Number of items | 1 |
Weight | 0.000625 Pounds |
Width | 3 Inches |
12. Guardian Fall Protection 11203 IS-72-2R 6-Foot Double Leg Internal Shock Lanyard with Rebar Hook
Made with a heavy duty outer polyester webbing and a polyester core specially sewn in to reduce impact forcesLightweightRebar hook included6 feet in lengthDouble leg lanyard
Specs:
Color | 0 |
Height | 2.9 Inches |
Length | 10.6 Inches |
Number of items | 1 |
Size | 6 ft |
Weight | 5.15 Pounds |
Width | 8.5 Inches |
13. 3M DBI-SALA ExoFit NEX 1103070 Nomex/Kevlar Full Body Harness, PVC Coated Alum Back/Side D-Ring's,Comfort Padding, Locking Quick Connect Buckle Leg Straps, Small, Black
- Resistant up to 40 cal/cm2 making it ideal for use where high voltage electricity is a concern
- Non-conductive spring-loaded design automatically stands-up ensuring fast, easy and safe connections to your fall arrest system
- Lightweight one-handed use with memory fit web-lock ensures fast, non-slipping connections
- Insulators behind exposed hardware prevent contact with body during "hot" situations
- PVC coated aluminum back and side D-rings, Nomex/Kevlar fiber webbing and comfort padding, locking quick connect buckle leg straps (size Small)
- For industrial/occupational use only. Not for consumer sale or use
Features:
Specs:
Height | 20.25 Inches |
Length | 15.5 Inches |
Number of items | 1 |
Weight | 10 Pounds |
Width | 12.5 Inches |
14. 3M Protecta Rebel AD115B 3/16" Galvanized Cable Self Retracting Lifeline, Swivel Hook, Housing Carabiner, 15', Red/Black
- Swiveling anchorage point
- Swiveling self-locking snap hook on lifeline
- Rugged aluminum housing
- Speed sensing all metal brake system
- 15 ft (45m) of 3/16" (5mm) galvanized steel wire rope with swiveling snap hook, swiveling anchorage and carabiner
- For industrial/occupational use only. Not for consumer sale or use
Features:
Specs:
Height | 6.375 Inches |
Length | 2.5 Inches |
Number of items | 1 |
Size | 15-Feet |
Weight | 7 Pounds |
Width | 6.625 Inches |
15. X XBEN Portable Safety Belt Fall Arrest Kit, With Hip Pad and 2 D Rings, Personal Protective Equipment Safety Climbing Harness
Side D rings,compact, lightweight and portable design: Easy to wear and adjust. protect belt will hold and sustain you at a specific work location such as rebar tying, tower maintenance, wall-form work safety harness, ladder work belt, trees climbing harness etcDurable polyester construction protect...
Specs:
Color | 2 D-rings |
Size | 31" - 56" |
16. Guardian Fall Protection 11200 IS-72 6-Foot Internal Shock Lanyard with snap hooks
- Made with a heavy duty outer polyester webbing and a polyester core specially sewn in to reduce impact forces
- Lightweight
- A Guardian Fall Product
- 6 feet in length
- Single leg lanyard
Features:
Specs:
Color | 0 |
Height | 5 Inches |
Length | 6 Inches |
Number of items | 1 |
Size | 6 Feet |
Weight | 2.5 Pounds |
Width | 6 Inches |
17. Eyeglass Lanyard, Black, Mono Slide, Rubber Sleeves, 15320
- 10 different attachments
- 6-quart stainless steel bowl with comfortable handle
- Bowl-lift design
- 10 different speeds, powerful enough for any task or recipe
- Includes: burnished flat beater, power knead spiral dough hook, wire whip
- All-metal 10-speed stand mixer with powerful 575-watt motor
- 6-quart stainless-steel mixing bowl; direct-drive transmission
- Electronic speed sensor; auto shut-off; Soft Start minimizes splatter
- Wire whip, burnished flat beater, spiral dough hook, and pouring shield included
- Measurements H: 16.5, W:11.3, D:14.6
Features:
18. Guardian Fall Protection 10560 HitchClip, Black, 3-Pack
Provide an additional 10-Inch to the length of your suspendersFor the extra big and tall builderFor use on multiple suspender models and suspension systemsMultiple accessory optionsMade in the USAPatent pending "key-hole" designIncredibly lightweightDoes not require flashingMultiple accessory option...
Specs:
Height | 1 Inches |
Length | 10 Inches |
Number of items | 1 |
Weight | 1.1 Pounds |
Width | 2.5 Inches |
19. 3M DBI-SALA Medium ExoFit NEX ConstructionFull Body Style Harness With Tech-Lite Aluminum Back D-Ring
Fall ProtectionManufacturer: 3MMade in: United StatesHybrid shoulder, back, leg and hip padding with premium comfort and durabilityRevolver vertical torso buckles make non-slip adjustment of shoulder straps fast and easyDuo-Lock quick connect buckles with memory-fit web-lock ensures an exact fit eve...
Specs:
Color | Blue/Gray |
Height | 6.4 Inches |
Length | 16 Inches |
Number of items | 1 |
Size | Medium |
Weight | 4.5 Pounds |
Width | 14 Inches |
20. RATS Tourniquet with READYMAN Every Day Carry Belt Sleeve Holder
✅ RATS Rapid Application Tourniquet is fast, easy and combat proven.✅ Designed by a 28 year Special Forces Veteran and also suitable for small limbs such as children and working dogs✅ Proven to be effective in occluding blood flow in both upper & lower extremities by the U.S. Army's Institute ...
🎓 Reddit experts on fall arrest equipment
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where fall arrest equipment are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
Or, you spend $300 once and you don't have to hire a lift or someone else to do a simple gutter clean-out.
I understand some people are scared or nervous of getting on their roof, but for the competent, an anchor system is a very common, well used and actually quite simple solution to keeping you safe.
I have a similar system that I installed myself when I bought my current home 2 years ago. So far I used it for 3 gutter cleanings, multiple frisbee, ball, nurf dart retrievals, a chimney cleaning, a bathroom fan vent install, tree branch trimming from a tree whose branches were getting to close to my roof and a couple roof/shingle inspections after some pretty big storms swept through. So instead of spending $4500 on lift rental or contracting out each of these jobs, I spent about $300 on a kit and some more anchors.
I also have an intimate knowledge of the condition of my roof, how it's wearing, where moss is beginning to grow (next project is zink strips, I live on the south west coast of BC)
FYI, "made in the USA" does not mean "all materials sourced from the USA." Also, while you sourced one safety harness which indicates at the bottom of the site that it is "Made in the USA," it is also many times more expensive than the common ones found on Amazon.
Also, I believe you dodged my point. Do you agree or disagree that tariffs are compatible with the formerly-conservative idea of free market capitalism?
>There are products that it is in your national interest to make domestically.
And yet, the United States did not impose tariffs on rare earth substances imported from China, which are used in all variety of electronics and military hardware.
If it's not in the national interest to minimize the cost of raw materials used in one's national security, then what is? Or do you believe the government is deliberately importing inferior materials from China?
Hi, new to climbing and looking for advise. There is a new rail to trail being built near my house and I somehow became caretaker to the trail. It has been basically 70 years of neglect and was built on a granite hill with a cliff on one side and a berm on the other. The hill is composed of fractured granite with a lot of invasive species growing between the rocks and fracturing it. I would like to be able to get the invasive species out but it is impossible on the cliff side. I plan on rappelling myself on the top side and tie the rope to the trees and be able to slowly walk down the edge and pull out or cut any vegetation.
What gear would I need? I was looking at https://smile.amazon.com/gp/product/B018RLPEY0/ref=ox_sc_saved_title_9?smid=A5THPGRP6FZBY&psc=1 but this seems to be only when you actually fall and not provide support or anchoring while I work or is this more what I need https://smile.amazon.com/gp/product/B073LSTSW3/ref=ox_sc_saved_title_10?smid=A2760MNFACRLA8&psc=1 ? I know I am supposed to get dynamic rope but its only 20 feet down max, would static rope be okay?
I would like to be able to be supported behind my back or on the side to be able to make cuts with I am going to use a one handed reciprocating saw or loppers.
The cliff is 15-20 feet tall max with it being a full 90 but above it is a dirt hill with trees greater than 12 inches diameter with a steep but with ropes manageable 60-70 degrees. You can walk around the cliff to reach the top as there is a trail up there. The closer you get to the cliff the more steep it gets.
Am I doing this wrong? Is this too dangerous? Thanks in advance.
My husband and I just DIY'd our metal roof last summer. It was labor intensive but fairly easy to do. It took us a few weeks to complete only because we replaced all of the decking at the same time (as most of it was delaminating). Total cost of materials for a snap-seam (hidden fastener) roof and new decking was approximately $6,000.... Our previous roof had been totalled in a hail storm so including the insurance payout, our actual out of pocket cost was like $100. So far we love it.
Two things I would do differently: One, don't skip the snow bars if you get any snow at all. We will be adding some before next winter. Two, add roof anchors every 8-10 feet under the ridge cap. This roof is horrible to walk on. Ours is only a 4/12 pitch and I fell off once.... My feet started sliding and there was nothing I could do to stop it. Luckily I was on the side that's only 9-ish feet off the ground and I was able to ninja roll out of it.
I used the Conterra Tool Chest for about a decade.
(In fact we used a version of this built by a local guy who knocked it off, and added a drawstring so things wouldn't fall out of it.)
One thing that is nice about this pack is it hold the radio in the vertical orientation which results in the best reception (antennas are sensitive to the orientation). Of course for best results we train members to remove the radio from the back so you're not driving signal into your body.
You will not be unprotected on your initial climb in if you use a line launcher or something similar on one side to put a line over the cross of your roof to the other. You then tie the rope in to a fixed point on the other side (like a tree or car) using a sling.
I used a kong ball with a hole in it (https://www.amazon.com/KONG-Ball-Dog-Medium-Large/dp/B0002DHOJA) and tied a thin 100 lb test nylon rope to it then launched it across with a dog ball launcher (https://www.amazon.com/Chuckit-Classic-Launcher-Colors-Vary/dp/B00006IX59). Once the small nylon rope was across the roof, I then tied it to a 100 foot 5/8" rope (https://www.amazon.com/Guardian-Fall-Protection-01360-VL58-100/dp/B004EEPTDG) and pulled it back across the roof so I could safely tie in.
It adds a few minutes to the time to get on the roof but it is worth it as you will have very low risk of falling because you will always be tied in.
I also use fall protection whenever I need to get up on a ladder on my 2nd story home. I have several different anchors that I can hang ropes from depending upon where I need to work.
You should also always be tied in moving anchor to anchor, something like this comes in really handy if you need to move across a larger roof: http://www.fallprotectionpros.com/guardian-big-boss-dual-leg-lanyard.html
This is a great video for finding rafters when you nail the fall protection in:
https://www.youtube.com/watch?v=OIMEMffezwI
All in all you would need to buy:
When I did this on my home I:
If your shingles are older this job will be tougher. Old shingles tend to tear instead of lifting.
I'll also recommend the ultimate focus tool, it basically does everything you need and makes you faster, which is something that gets you rehired, as for a bungee, this is a good one with a great length. I'm also a student so the Ultimate focus tool did hit my wallet, but it's well worth it.
My Essentials for an Electrics call
Ultimate Focus Tool: http://www.fullcompass.com/prod/224936-StageJunk-7280-RT/
Adjustable C Wrench: http://www.homedepot.com/p/Husky-8-in-Double-Speed-Adjustable-Wrench-96596/203467743
Screwdriver (multi bit) Similar to this one: http://www.amazon.com/dp/B0015SBILG/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&colid=3NM0LBGK3Q7YA&coliid=I3TJ4V0YRRN22T
Belt Tether: http://www.amazon.com/gp/product/B007H6DRGO?psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s00
Leatherman Surge: http://www.leatherman.com/surge-3.html#start=2
Mini Mag Light: http://www.amazon.com/MAGLITE-M2A016-Mini-Flashlight-Black/dp/B00002N6SL%3Fpsc%3D1%26SubscriptionId%3DAKIAILSHYYTFIVPWUY6Q%26tag%3Dduckduckgo-ffsb-20%26linkCode%3Dxm2%26camp%3D2025%26creative%3D165953%26creativeASIN%3DB00002N6SL
Gloves Preferably leather for heat protection when focusing, good dexterity for tying knots and I generally like a Velcro latch on the wrist to give a snug fit
Hahaha, no not the harness, just the anchor. Just a tie off point I don't need to worry about.
https://www.amazon.com/Guardian-Fall-Protection-00500-11-Inch/dp/B004A7XUQU/ref=pd_sim_469_3?_encoding=UTF8&pd_rd_i=B004A7XUQU&pd_rd_r=59VRW9Y64W0RDWCWKWZA&pd_rd_w=pbiiJ&pd_rd_wg=5bIgg&psc=1&refRID=59VRW9Y64W0RDWCWKWZA
I'm talking about nailing that up in my attic and using it as the point I tie the top of the ladder onto. Something strong enough to not move.
Well, as I told him... Almost anyone willing to have a boom arm suspended from their ceiling can probably figure it out and fabricate it for themselves :D I'll let him know people would use it, but if you wanted a headstart it's basically 3 microphone boom stands with this attached to the end to neutralize weight.
His endgame is to hook the headset into the arm, having special contacts (or something) at the joints so it can utilize the full 3-in-1 length and move it around the room. He's got a system right now using keychain/Id card retractors for seated stuff that he adds more or keychains to for weight changes. Getting from where he is now to his grandiose plan probably will take time, haha.
Not terribly comfortable, but it does the job and is relatively cheap.
https://www.amazon.com/dp/B018RLPEY0
https://www.amazon.com/gp/aw/d/B004A7XVU0/
Please please PLEASE DO NOT CLIMB until you know how to PROPERLY use that equipment (its really not hard, just Google it). Also, inspect the equipment when you get it for any defects.
This is a great VR room build idea, unfortunately instead of posting a build DIY of a few simple things from Amazon, or a home improvement store some people want to try and charge a middle man fee. Just using google I found pretty much each component used to build this.
 
One of the harnesses used in the video
Ceiling hook
Fall protection lanyard
Rock Climbing Carbineers
 
I didn’t look too heavily beyond finding the exact harness, but already you have the majority of what you need and probably spent around $150.00, asking for $300.00 dollars to gather a few simple already manufactured items together for a DIY project is ridiculous.
cross posted this from /r/vive hopefully to save more people from wasting money.
DBI Sala makes a nomex/kevlar harness for welding. I've used lots of their harnesses in the past and been to many of their classes. Like others have said, make sure it fits nice and snug.
https://www.amazon.com/Squids-3400-Glove-Grabber-Black/dp/B002ORK3M2
would this work? or too big.. Honestly I would just use a plastic safety pin (plastic so the metal doesnt scratch the leather)
https://www.amazon.com/Plastic-Knitting-Crotchet-Locking-Markers/dp/B00VNI2PJ2/ref=sr_1_9?s=arts-crafts&ie=UTF8&qid=1518041432&sr=1-9&keywords=plastic+safety+pins
$12 CLC drill/driver holster for your tool belt. So much less bending over and saves a ton of time freeing up both hands. Add a tool tether so if you’re in a lift or ladder the people under you are safe. Also saves the drill if you have butter-fingers.
https://www.amazon.com/gp/aw/d/B000LNM2H0/ref=mp_s_a_1_5?ie=UTF8&qid=1518209629&sr=8-5&pi=AC_SX236_SY340_QL65&keywords=clc+holster&dpPl=1&dpID=51KrTs13UyL&ref=plSrch
https://www.amazon.com/gp/aw/d/B0001VO35Q/ref=mp_s_a_1_3?ie=UTF8&qid=1518209667&sr=8-3&pi=AC_SX236_SY340_QL65&keywords=tool+tether&dpPl=1&dpID=31x1v3yD2cL&ref=plSrch
Edit: Sorry. That’s two things.
this kinda looks like it it actually might be worth good money.
When my kids were young I did something very similar with our Rottweiler. He loved pulling them. The harness had a metal loop at the top where I could run a strap through it and attach it to each of the PVC pipes. I suggest you consider something similar to free your hands. There is a safety belt on Amazon for $32 with a metal loop on each side which could very easily be used to attach to the PVC. Also, if you used longer PVC the first cart wouldn't have to tip back so far.
Not sure if this sub allows Amazon links, but here it is (with no referral info in the URL): https://www.amazon.com/Xben-Portable-Personal-Protective-Equipment/dp/B075JC7DSQ/
SPF 50 is a good idea. If you don't have a water jug it might not be a bad idea to get one.
Stay hydrated, wear your PPE if and when appropriate. If you have work gloves you might want to get a glove clip, it's the only way I can keep a pair of gloves for more than a day. Ergodyne Squids 3400 Glove Grabber, Black https://www.amazon.com/dp/B002ORK3M2/ref=cm_sw_r_cp_apa_i_JYo0Cb38RB73H
It's for occasions like this (and roller coasters) that I bought one of these. After having lost two pair in one year I bought one of these things. I went white water rafting and didn't lose them. Somehow that little strand of elastic is like magic.
HitchClip I bought the kit you were looking at along with a pack of HitchClips. They are permanent and you shingle over them.
I noticed that the hook on harness kit is rather heavy and awkward. Just be careful that you don't trip over your safety line.
Yeah I had a SALA that was like this: https://www.amazon.com/dp/B004RH3OI2
We were climbing ski-lift towers which required being a nimble: laying prone, curved ladders, etc. I got stuff stuck with the SALA several times. I started wearing the other departments basic petzel harnesses after a week.
There's nothing on the outside, so I was thinking of nailing down a few roof anchors.
https://www.amazon.com/Ergodyne-3100-Carabiner-Adjustable-Standard/dp/B0001VO35Q/ref=sr_1_6?keywords=squids&qid=1568214704&s=gateway&sr=8-6
It is a type of tourniquet.
https://www.amazon.com/RATS-Tourniquet-READYMAN-Sleeve-holder/dp/B074KP53SM
They make tool lanyards for this purpose, however using the tool becomes slightly more difficult with it depending on how long the lanyard is.