(Part 2) Reddit mentions: The best hose clamps
We found 30 Reddit comments discussing the best hose clamps. We ran sentiment analysis on each of these comments to determine how redditors feel about different products. We found 21 products and ranked them based on the amount of positive reactions they received. Here are the products ranked 21-40. You can also go back to the previous section.
21. Pro Tie 33200 SAE Size 4 Range 1/4-Inch-5/8-Inch Mini All Stainless Hose Clamp, 10-Pack
Band, housing, and screw are all stainless steelSAE Size: 4Low Range: 1/4-InchHigh Range: 5/8-InchScrew Size: 6 mm slotted hex head
Specs:
Color | Silver |
Height | 1 Inches |
Length | 1 Inches |
Number of items | 10 |
Size | SAE Size 4 Range 1/4" to 5/8", 10-Pack |
Width | 0.31 Inches |
🎓 Reddit experts on hose clamps
The comments and opinions expressed on this page are written exclusively by redditors. To provide you with the most relevant data, we sourced opinions from the most knowledgeable Reddit users based the total number of upvotes and downvotes received across comments on subreddits where hose clamps are discussed. For your reference and for the sake of transparency, here are the specialists whose opinions mattered the most in our ranking.
Sorry I was on my phone before. let me see what i can find. I can't find the exact coupler I used but I might be able to find something else with some searching
ed: you're in luck, found a two step way using items available on amazon that connects to the 1/4" flare you originally tried to shove the hose directly onto. when i got my oven in, i needed it working THAT DAY, and the local hvac supply place didn't have 1/4" flare swivel couplers in stock.
http://www.amazon.com/LASCO-17-5911-4-Inch-Female-Adapter/dp/B008E5CVKA/ref=sr_1_1?ie=UTF8&qid=1419741989&sr=8-1&keywords=1%2F4+inch+female+flare+swivel
http://www.amazon.com/dp/B006PKL6Z2/ref=biss_dp_t_asn
You may also want a hose clamp or two to go with that
http://www.amazon.com/Pro-Tie-33200-4-Inch-5-Stainless/dp/B006IOZ3YU/ref=sr_1_1?s=industrial&ie=UTF8&qid=1419742116&sr=1-1&keywords=1%2F4%22+hose+clamp
when i did it locally, i found a 1/2" Flare to 1/2" NPT swivel, and had to get some teflon tape and put a 1/2" NPT x 1/4" barb on it instead.
As noidios said the kegs are going to cost more unless you get a good deal from someone. My local store has the pin locks for $65 each.
Co2 tank sounds about right. You may need to have it filled though depending on how the store sells them. I would consider a bigger tank or a spare as you don't want to run out of Co2. 1 5lb can dispense roughly 6-8 kegs and that is if you don't have a leak. Some kegs can leek. Seeing as how they are all connected and will equalize in pressure one leak going unnoticed for a night can cost you the tank and the pressure in all your attached kegs.
Manifolds is dead on on price.
50ft of 5/16 at $50. maybe shop around on that one. If you know your PSI you can check out This I wouldn't think you would exceed 50 PSI under normal conditions.
Hose Clamps since you are going to be going off of the OD it should work as the OD of the smalles tube is 5/16. Figure you will need 4 for each keg (2 on each end of the line) plus 2 for the line going from the manifold to the tank should be about 34 (assuming 8 kegs.) so 4 orders comes to $$20
3/16 for beer line. I would look at this 100ft A bit more cost effective. Others can chime in on them if I linked a bad product.
Keg Lube save a couple bucks for 4 oz vs the normal 1 oz. Easier to dispense and keep clean imo.
Places where I would spend a little more:
Shanks are up to you but I would go the extra stop for stainless if you can just so you don't have to worry about chrome flaking off a few years from now.
Handles - for the price I take it you are looking at the cheap ones from northern brewer? Can't speak for them for myself but I think they will work. worst comes to worse you replace them a year later.
Edit: Also the kit you listed 1 4 way manifold (say $50 for rounding), 4 bev locks, 4 gas locks (6.50 ea so $52) the faucests look like the cheap chrome ones from amazon $31 ea ($124), 3 feet of gas line with 2 clamps and a faucet wrench aren't worth much.
$250 for the kit they are selling for $382 unless I missed something.+dual reg at say $98 but$50 for the regulator. so about $280 in parts that they are charging you $382 for. unless I missed something elsethieves are creatures of opportunity. It doesn't really matter what your bike's made of. What matters is how much of a pain in effort and time you can make it to steal. So it really comes down to a simple list of things:
`the D-lock is not just a big padlock that connects the two ends of a cable. It has to be around your frame and around a secure object at the same time. Please do not make this mistake!
Or custom-ordering screws that require a pentagon-shaped screw tip to turn, that's a rare tool thieves are unlikely to have. You'll have to order the tool, of course.
hose clamps locking down the quick-release levers of your wheel hubs.
here is Hal grading people's lock jobs. Follow his advice.