#12 in Router parts & accessories
Use arrows to jump to the previous/next product
Reddit mentions of Freud 1-3/4 In Diam by ¾ In Double Flute Straight Router Bit w/½" Shank (12-194)
Sentiment score: 2
Reddit mentions: 7
We found 7 Reddit mentions of Freud 1-3/4 In Diam by ¾ In Double Flute Straight Router Bit w/½" Shank (12-194). Here are the top ones.
or
Ideal for general stock removalFeatures Freud's TiCo Hi-Density Carbide cuts for maximum durability, long life and a flawless finishCuts all composite materials, plywoods, hardwoods, and softwoodsUse on CNC and other automatic routers as well as hand-held and table-mounted portable routersUnique shear angles provide smooth finish, Imported
Specs:
| Color | Red |
| Height | 0.51 Inches |
| Length | 6.25 Inches |
| Size | One Size |
| Weight | 0.55 Pounds |
| Width | 0.82 Inches |
I used a 1 3/4 flat bit and took off between 1/8 and 1/4 per pass, sometimes more in particularly high spots. The slab started out very wavy!
Next time I would use longer rails, both for the sled to ride on and for the sled itself, I kept having to move the slab and rails around to get at different areas and it was a pain.
Yeah, I second this advice. I used this bit with good results the last time I used a router sled. With a 1-3/4" cut, it's about 7-8 passes per foot depending on how much overlap each pass.
You can use a larger bit and just take off less with each pass. Personallyy with flattening a workbench I'd rather be on the side of larger bit, less depth at one time. Here's a decent 1 3/4" flat bottom
http://www.amazon.com/gp/product/B00004T7CZ
I use two bits: a 2” from Infinity and 1.75” made by Freud:
Freud 1-3/4" (Dia.) Double Flute Straight Bit with 1/2" Shank (12-194) https://www.amazon.com/dp/B00004T7CZ/ref=cm_sw_r_cp_api_o753BbSQZB01S
This is the one I use https://smile.amazon.com/Freud-Double-Flute-Straight-12-194/dp/B00004T7CZ/ref=sr_1_1?ie=UTF8&qid=1542225656&sr=8-1&keywords=freud+straight+router+bit+1+3%2F4
I used a 1 3/4" Freud straight cut bit. Something like a Whiteside WS1101 would provide 2” of cutting and be slightly more time efficient I suppose. On this slab the result was pretty good, although given the width of the sled and me leaning over it with too much weight at times, some routes were slightly different. Not much though, but I did give it a 60/100/150 grit belt sand before random orbiting. I used the same process on the maple bench you see in some of the photos. With a smaller sled and not having to lean over the work on the garage floor, the maple top came out damn near perfect and required only finish sanding (there were visible lines on the maple but you couldn't really feel them brushing around with your hand).
I've used a similar setup to finish end grain slices and gotten best results from a 1 3/4” Freud straight bit. Shallow passes with the bit's big cutting area leaves a pretty smooth finish. Minimal sanding (think 15 mins with ROS) to get rid of faint lines.
Also, make sure the wood itself isn't moving at all. That can produce gouges.
Freud 1-3/4 In. Diameter by ¾ In. Double Flute Straight Router Bit with ½" Shank (12-194) https://www.amazon.com/dp/B00004T7CZ/ref=cm_sw_r_cp_apa_rtZHzbA2T2QG2